Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coatings Prepared by Laser Cladding

21-4N(5Cr21Mn9Ni4N)is extensively employed in the production of engine valves,operating under severe conditions.Apart from withstanding high-temperature gas corrosion,it must also endure the impact of cylinder explosion pressure.The predominant failure mode of 21-4N valves is abrasive wear.Surface coatings serve as an effective approach to prevent such failures.In this investigation,Laser cladding technology was utilized to fabricate AlCoCrFeNiTi high entropy alloy coatings onto the surfaces of 21-4N valves.According to the findings,the cladding zone has a normal dendritic microstructure,a good substrate-to-cladding layer interaction,and no obvious flaws.In terms of hardness,the cladding demonstrates an average hardness of 620 HV.The hardness has increased by 140%compared to the substrate.The average hardness of the cladding remains at approximately 520 HV even at elevated temperatures.Regarding frictional wear performance,between 400℃and 800℃,the cladding layer exhibits an average friction coefficient of 0.4,with the primary wear mechanisms being abrasive wear,adhesive wear,and a minor degree of plastic deformation.

Effects of process parameters and annealing on microstructure and properties of CoCrFeMnNi high-entropy alloy coating prepared by plasma cladding

Plasma cladding was used to prepare a CoCrFeMnNi high-entropy alloy(HEA)coating under different conditions.The process parameters were optimized using an orthogonal experiment design based on surface morphology quality characteristics,dilution rate,and hardness.The optimal process parameters were determined through range and variance analysis to be a cladding current of 70 A,a cladding speed of 7 cm·min^(-1),and a powder gas flow rate of 8 L·s^(-1).During the optimized experiments,both the cladded and annealed CoCrFeMnNi HEA coatings exhibit some pores,micro-voids,and a small amount of aggregation.However,the aggregation in the annealed coating is more dispersed than that in the cladded coating.The cladded CoCrFeMnNi HEA coating consists of simple FCC phases,while a new Cr-rich phase precipitates from the FCC matrix after annealing the coating at a temperature range of 550°C-950°C.After annealing at 850°C,the proportion of the FCC phase decreases compared to the cladded coating,and the number of large-angle grain boundaries is significantly reduced.However,the proportion of grains with sizes below 50μm increases from 61.7%to 74.3%.The micro-hardness and wear resistance of the cladded coating initially increases but then decreases with an increase in annealing temperature,indicating that appropriate annealing can significantly improve the mechanical properties of the CoCrFeMnNi HEA coatings by plasma cladding.The micro-hardness of the CoCrFeMnNi HEA coatings after annealing at 650°C increases to 274.82 HV_(0.2),while the friction coefficient decreases to below 0.595.

Microstructure and microhardness of Co-8.8Al-9.8W superalloy cladding layer with different boron content

TIG welding was used to deposit Co-8.8 Al-9.8 W-0.2 B superalloy on 304 austenite stainless steel. The form factor of weld, dilution ratio, microhardness, microstructure and distribution of alloying elements were investigated. The microstructure of cladding layer was mainly hypoeutectic. The primary phases were cobalt-rich solid solution. The eutectic phase was composed of cobalt-rich solid solution,Co6W6C and Co Cx. When the boron content increased from 0.2% to 0.5%,the dilution ratio decreased,the primary phase became coarse and the microhardness decreased. When the boron content was from 0.5% to 2%,the dilution ratio and microhardness increased obviously,but the primary phase was refined.The hard phase of Co-8.8 Al-9.8 W became refined and the amount was raised,and the performance of cladding layer was improved with appropriate boron increase.

Ultra wear resistant TiC-Fe coating prepared by high efficient and economic plasma cladding method

The key components of engineering machinery frequently failed due to working in the high load and high wear operating envir-onment.And the performance of the Fe-based alloy coatings typically employed need to be improved for fulfilling the service requirements.Herein,a TiC strengthened Fe-based alloy cladding layer,named TiC-Fe coating,was designed and prepared by plasma cladding technology.The frictional wear performance of coating under various loads was tested.The wear morphology of the coating was observed,and its wear mechanism was examined.The results indicated that the TiC-Fe coating was well formed and metallurgically bonded to the Q345C substrate.Its microstructure mainly consisted of Fe-Cr solid solution,α-Fe phase,(Fe,Cr)_(7)C_(3) phase and TiC phase.The coating exhibited an average microhardness of 980 HV0.2,which was about 5.4 times that of the Q345C substrate.The wear mass loss of the TiC-Fe coatings was much smaller than that of the Q345C substrate,which indicated that the wear resistance of the Q345C coating was superior to the substrate,and the wear mechanism of the coating was mainly attributed to the abrasive wear.

Microstructure and high temperature tribological behavior of laser cladding Ni60A alloys coatings on 45 steel substrate

The crack-free Ni60 A coating was fabricated on 45 steel substrate by laser cladding and the microstructure including solidification characteristics, phases constitution and phase distribution was systematically investigated. The high temperature friction and wear behavior of the cladding coating and substrate sliding against GCr15 ball under different loads was systematically evaluated. It was found that the coating has homogenous and fine microstructure consisting of γ（Ni） solid solution, a considerable amount of network Ni-Ni3 B eutectics, m^23C6 with the floret-shape structure and Cr B with the dark spot-shape structure uniformly distributing in interdendritic eutectics. The microhardness of the coating is about 2.6 times as much as that of the substrate. The coating produces higher friction values than the substrate under the same load condition, but the friction process on the coating keeps relatively stable. Wear rates of the coating are about 1/6.2 of that of the substrate under the higher load（300 g）. Wear mechanism of the substrate includes adhesion wear, abrasive wear, severe plastic deformation and oxidation wear, while that of the coating is merely a combination of mild abrasive wear and moderate oxidation wear.

Effect of Laser Cladding Processing Parameters on Nitinol’s Clad Dimensions, Microstructure, and Hardness

Nickel Titanium alloy (Nitinol) is characterized by its good mechanical properties, good damping properties in addition to its distinctive shape-memory effect and superelasticity effect besides its great bio-mechanical compatibility and corrosion resistance. These properties have empowered its applications, particularly within the bio-medical and aerospace industry. Despite these exceptional properties, the manufacturing of Nitinol by conventional methods is exceptionally troublesome and costly and consequently must be inspected. Therefore, additive manufacturing specifically laser-based ones were used recently. In this research, the effect of processing parameters of laser cladding/laser direct deposition on Nitinol’s Microstructure, Hardness and Clad Dimensions was evaluated. Systematic characterization of Nitinol samples was done utilizing Optical Microscopy and Vickers hardness tester. Samples of Nitinol were synthesized with different processing parameters using laser cladding and its properties were investigated and compared to one another to get the optimum processing parameters to synthesize a near net shape, fully dense Nitinol component with reliable properties. The results showed that there’s a processing parameter window at which the alloy possesses its best mechanical and functional properties which were of Laser power of value 1.25 Kw, Scan speed of 1.5 m/min and powder deposition rate of 1.5/1.5 RPM, these conditions resulted in the formation of martensite phase which is responsible for its functional properties with 40% volume fraction and a hardness value of 598 HV.

Microstructure and properties of laser cladding of 316L stainless steel on hydraulic support tube

In consideration of the special environmental conditions of coal equipment in mining, the seamless steel tube of hy-draulic prop made of 20^# carbon steel was taken as the substrate, and 316L stainless steel powder was used to clad the sub-strate by a fiber-coupled semiconductor laser. The microstructure of the cladding layer was determined by metalloscope. The hardness, wear resistance and corrosion resistance of the cladding layer were measured. The results show that metallurgy bind-ing interface between the cladding layer and the substrate is obtained without defects such as cracks and pores. The hardness of the cladding layer is much higher than that of the matrix, and the wear resistance and corrosion resistance are simultaneously better. According to the analysis, it is summarized that the improvement in performance of the cladding layer is closely related to the change of microstructure and the thermal effect in the cladding process. The maximum hardness occurs in the equiaxed zone, and with the grain coarsening, the hardness reduces simultaneously. In addition, the precipitated phase, hard particles and trace elements also have a great influence on the properties of the cladding layer, and they will prevent the surface from ab-rasion and reduce the plastic deformation of the matrix. It is verified that the 316L stainless steel is suitable for the 20^# steel in laser cladding repairing process. Since this study focused on coal machine equipment parts, it has certain practical significance for the repair of hydraulic equipment.

Microstructure and mechanical properties of Ni-based composite coatings reinforced by in situ synthesized TiB_2 + TiC by laser cladding

A Ni-based composite coating reinforced by in situ synthesized TiB2 and TiC particles was fabricated on Ti6A14V by laser cladding. An attempt was made to correlate the thermodynamic predictions and experimental observation. The micro- structure and the microhardness profile across the coating were investigated by means of X-ray diffraction （XRD）, scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and a hardness tester. It is found that the coating mainly consists of a large number of reinforcements （black blocky TiB2, flower-like or equiaxial TiC, and fine acicular CrB） and the 7 matrix. The hardness of TiB2, TiC, and CrB reinforcements is much higher than that of the 7 matrix. The dispersive distribu- tion of such high hardness reinforcements causes the increase in hardness of the whole coating. The average value of the hard- ness is approximately Hv0.2 700 in the coating. The hardness of the coating is obviously higher than that of the substrate due to the dispersion strengthening of reinforcements.

Microstructure and Thermal Physical Parameters of Ni60-Cr_3C_2 Composite Coating by Laser Cladding

To satisfy performance and long life requirements for hot forging die,Ni60-Cr3C2 composite coatings were prepared on the high-speed steel W6Mo5Cr4V2 using laser cladding technology.Laser clad coatings with different ratios of Ni60：Cr3C2 were investigated by scanning electron microscopy（SEM）,X-ray diffraction（XRD）,energy-dispersive X-ray analysis（EDX） and micro-hardness tester,respectively.Specific heat capacity and thermal conductivity were measured by Laser Thermal Constant Meter.Thermal expansion coefficient and elastic modulus were measured by Dynamic Mechanical Thermal Analyzer and Electro-Hydraulic Servocontrolled Testing System,respectively.The results indicated that Ni60＋50wt% Cr3C2 composite coating had dense and homogeneous structure,as well as a metallurgical bonding with the substrate.With the increase of Cr3C2 content,volume of chromium-containing compounds in the composite coating increased,microhardness increased and microstructure refined.The thermal physical parameters results showed that Ni60＋50wt% Cr3C2 composite coating was overall worse than W6Mo5Cr4V2,but had a higher hot yield strength to alleviate hot fatigue and surface hot wear of hot forging die during hot forging and thus improve the service life of hot forging die.

Influence of heat treatment on microstructure and mechanical properties of FeCrNi coating produced by laser cladding

The FeCrNi alloy powders were used on the dovetail groove of FV520B steel to fabricate the multilayer laser cladding layers. The effects of heat treatment on the microstructure and mechanical properties of FeCrNi layers were investigated. The results showed that the heat treatment at the temperature ranged from 1073 to 1273 K refined the grains of the substrate materials and removed the soft zone of hardness between the fused zone (FZ) and base material (BM) effectively mainly due to a secondary quench of heat treatment. When the temperature of heat treatment was 1073 K, the maximum ultimate tensile strength (UTS) values of the laser cladding component were obtained. However, the heat treatment at high temperature had a bad effect on wear resistance of coatings at some extent.

Microstructure and properties of WC-12Co composite coatings prepared by laser cladding

A comprehensive study of the phase composition, microstructure evolution, microhardness and wear performance of WC-12 Co composite coatings fabricated by laser cladding using coaxial powder-feed mode was presented. It was shown that a combination of high scan speed and high laser energy density made WC on the edge of WC-12 Co composite powders partially melt in liquid Co and 304 stainless steel matrix, and then new carbides consisting of lamellar WC and herringbone M3 W3 C(M=Fe,Co) were formed. Meanwhile, WC-12 Co composite coatings with no porosity, cracks and drawbacks like decarburization were obtained, showing high densification and good metallurgical bonding with the substrate. Furthermore, a considerably high microhardness of HV0.3 1500-1600, low coefficient of friction of 0.55 and wear rate of(2.15±0.31)×10-7 mm3/(N·m) were achieved owing to the synergistic effect of excellent metallurgical bonding and fine microstructures of composite coating under laser power of 1500 W.

Microstructure characteristics of Ni/WC composite cladding coatings

A multilayer tungsten carbide particle（WCp）-reinforced Ni-based alloy coating was fabricated on a steel substrate using vacuum cladding technology.The morphology,microstructure,and formation mechanism of the coating were studied and discussed in different zones.The microstructure morphology and phase composition were investigated by scanning electron microscopy,optical microscopy,X-ray diffraction,and energy-dispersive X-ray spectroscopy.In the results,the coating presents a dense and homogeneous microstructure with few pores and is free from cracks.The whole coating shows a multilayer structure,including composite,transition,fusion,and diffusion-affected layers.Metallurgical bonding was achieved between the coating and substrate because of the formation of the fusion and diffusion-affected layers.The Ni-based alloy is mainly composed of y-Ni solid solution with finely dispersed Cr7C3/Cr（23）C6,CrB,and Ni＋Ni3Si.WC particles in the composite layer distribute evenly in areas among initial Ni-based alloying particles,forming a special three-dimensional reticular microstructure.The macrohardness of the coating is HRC 55,which is remarkably improved compared to that of the substrate.The microhardness increases gradually from the substrate to the composite zone,whereas the microhardness remains almost unchanged in the transition and composite zones.

Effects of TiB_2+TiC content on microstructure and wear resistance of Ni55-based composite coatings produced by plasma cladding

TiB2-TiC reinforced Ni55 matrix composite coatings were in-situ fabricated via plasma cladding on steels using Ti, B4C, and Ni55 as precursor materials at different proportions. Effects of TiB2+TiC content of ceramics phase on the microstructure and wear resistance were studied. The results showed that ceramic phases TiB2 and TiC were in-situ synthesized by plasma cladding, and the ceramic phase content significantly affected tribological performance and the wear mechanism of coatings under different loads. The composite ceramics protected coatings from further delamination wear by crack-resistance under a load of 30 N. Severe abrasive wear and adhesive wear were prevented when the load increased to 60 N because of the high hardness and strength of ceramic phases. Moreover, a compacted layer appeared on the wear surface of coatings with high content of ceramic phases, which effectively decreased the friction coefficient and wear rate. The TiB2-TiC composite ceramics significantly improved the wear performance of metal matrix composite coatings by different mechanisms under loads of 30 and 60 N.

Microstructure,strength and welding window of aluminum alloy-stainless steel explosive cladding with different interlayers

Aluminum 5052(Al 5052)-stainless steel 316(SS 316)plates were explosively cladded with Al 1100,pure copper and SS 304 interlayers.The operational parameters viz.,standoff distance,explosive mass ratio(mass ratio of the explosive to the flyer plate)and inclination angle were varied and the results were presented.The advent of interlayer relocates the lower boundary of the welding window,and enhances the welding regime by 40%.A triaxial welding window,considering the influence of the third operational parameter,was developed as well.Use of interlayer transforms the continuous molten layer formed in the traditional Al 5052-SS 316 explosive clad interfaces into a smooth interface devoid or with a slender presence of intermetallic compounds.The microhardness,ram tensile and shear strengths of the interlayered clads are higher than those of the traditional explosive clads,and the maximum values are witnessed for stainless steel interlaced Al 5052-SS 316 explosive clads.

Microstructure and Properties of Fe-Based Coating on Column Surface Formed by High Frequency Induction Cladding

The Fe-based coating was produced on the surface of the column substrate with a Al2O3 cylindrical sleeve by high frequency induction cladding, microstructure of the coating was investigated with scanning electron microscope (SEM), the crystal structure was characterized by X-ray diffractometer (XRD), the microhardness and wear resisitance of the coating were evaluated. The results show that a metallurgical bond between coating and substrate was obtained during the rapid solidification, the phases of the coating were composed of austenite and the eutectic of γ-Fe + (Cr, Fe)7(C, B)3. Compared with the substrate, the microhardness and wear resistance of the coating improved apparently, solid-solution strengthening and second-phase particle hardening led to these results.

Microstructures and properties of Fe-Co-B-Si-Nb coating prepared by laser cladding and remelting

High power laser cladding of [ （ Fe0. 5 Co0. 5 ） 0. 75 B0. 2 Si0.05 ] 95. 7 Nb4. 3 powder mixture afier-remelting was performed to fabricate Fe-based metallic glass coating on the surface of steel of China Classification Society： Grade B （CCS-B）. Scanning electron microscopy （SEM）, X-ray diffraction （XRD）, transmission electron microscopy （TEM） with energy dispersive spectrometer （EDS）, Vickers hardness tester and corrosion resistance tester were employed to characterize microstructures and evaluate properties of this coating. According to the results of SEM, XRD and TEM, the cladding coating consisted of nanocrystalline embedded in amorphous phase. EDS data indicated that Nb segregated in the amorphous matrix. The results of hardness test revealed that the hardness of the top layer was higher than that of the inner layer of the coating. The coating exhibited excellent corrosion resistance in a 3.5% NaCl solution.

Laser Multi-layer Cladding Experiment on the DD3 Single Crystal Using FGH95 Powder:Investigation on the Microstructure of Single Crystal Cladding Layer

Laser multi\|layer cladding experiments were performed on the substrate of DD3 single crystal with FGH95 powder as cladding material.The solidification microstructure in the sample was investigated.It was found that the solidification microstructure was greatly influenced by the crystallography orientation of the substrate and the local solidification conditions.When the angle between the preferred orientation of the single crystal and the direction of heat flow in the cladding layer is less than 30°,single crystal cladding layers were acquired.Otherwise the crystallography orientation of the cladding layer will deviate from the orientation of the substrate and the microstructure with polycrystalline appears.Meanwhile,even when the experiments were performed on the same preferred crystal surface,the solidification microstructures will be different distinctly resulting from the variation of the local solidification conditions.The secondary arms were degenerated and the primary arm spacing was about 10\|20μm.Further investigation shows that the phases of the cladding layer are mainly made up ofγ,γ′,the flower\|likeγ/γ′eutectic and carbide.The morphology ofγ′was cubical and the size is less than 0.1μm.

Microstructure and corrosion resistance of 304 stainless steel electroslag strip cladding

The 304 stainless steel strips were deposited one layer on carbon steel base metal by electroslag strip cladding （ESC） and submerged arc cladding （SAC）, respectively. The solidification microstrueture of ESC metal was analyzed by the optical microscopy, scanning electron microscope and energy dispersive spectroscopy. The corrosion resistance studies of strip cladding metals were carried out in 10% oxalic acid electrolytic etching test. The results showed that the cladding metal obtained by ESC presented low content of C, high content of Cr and enough alloying element of Ni in the chemical composition. The transition zone of ESC with small width was almost parallel with the base metal, leading to a lower dilution. There are three types of solidification modes （ A→AF→FA ） occurred in the ESC metal due to the decrease of cooling rate and degree of dilution from the transition zone to the top of ESC metal. As a result, the microstructure of ESC metal exhibited mainly austenite with a small amount of ferrite, contributing to achievement of better corrosion resistance.

Microstructure and wear resistance of AlCrFeNiMo_(0.5)Si_(x) high-entropy alloy coatings prepared by laser cladding

In recent years,the coating prepared by laser cladding has attracted much attention in the field of wear research.In this work,AlCrFeNiMo_(0.5)Si_(x)(x=0,0.5,1.0,1.5,2.0)high-entropy alloy coatings were designed and prepared on Q235 steel by laser cladding.The effect of Si content on microstructure,microhardness and wear resistance of the coatings was studied in detail.The results indicate that the AlCrFeNiMo_(0.5)Si_(x) highentropy alloy coatings show an excellent bonding between substrate and the cladding layer.The AlCrFeNiMo_(0.5)Si_(x) coatings are composed of nano-precipitated phase with BCC structure and matrix with ordered B2 structure.With the addition of Si,the white phase(Cr,Mo)_(3)Si with cubic structure appears in the interdendritic,and the morphology of the coating(x=2.0)transforms into lamellar eutectic-like structures.The addition of Si enhances the microhardness and significantly improves the wear resistance of the coatings.As x increases from 0 to 2.0,the average hardness of the cladding zone increases from 632 HV to 835 HV,and the wear rate decreases from 1.64×10^(-5) mm^(3)·(N·m)^(-1) to 5.13×10^(-6) mm^(3)·(N·m)^(-1).When x≥1.5,the decreasing trend of the wear rate gradually slows down.The wear rates of Si1.5 and Si2.0 coatings are 5.85×10^(-6) mm^(3)·(N·m)^(-1) and 5.13×10^(-6) mm^(3)·(N·m)^(-1),respectively,which is an order of magnitude lower than that of Q235 steel.

Microstructure evolution and liquid phase separation in Ta-O hypermonotectic melts during laser-cladding

A three-layer Ta_2O_5-containing coating was successfully fabricated by laser cladding on a pure Ta substrate. The maximum thickness of such a coating is about 1.6 mm. The microstructure, phase constitution and elemental distribution in the coating were investigated. Results show that the coating has been metallurgically bonded to the Ta substrate and the microstructure exhibits a graded change along the deposition direction from Ta substrate to the top of coating. In the layers I and II of the graded coating, the microstructure evolution can be confi rmed as a result of hypomonotectic reaction, but in the layer Ⅲ it was formed by hypermonotectic reaction. At the top of coating, the microstructure was still homogeneous although liquid phase separation had occurred, which can be attributed to the fact that the O-rich droplets do not have enough time to fl oat at high cooling rate. The theoretical calculation results show that during laser cladding, the solidifi cation time of the melt pool was less than 0.1 s, which fi ts well with the results from the experiment.