Clogging caused by coupled grain migration and compaction effect during groundwater recharge for unconsolidated sandstone reservoir in groundwater-source heat pump

In unconsolidated sandstone reservoirs,presence of numerous movable grains and a complex grain size composition necessitates a clear understanding of the physical clogging process for effective groundwater recharge in groundwater-source heat pump systems.To investigate this,a series of seepage experiments was conducted under in situ stress conditions using unconsolidated sandstone samples with varying grain compositions.The clogging phenomenon arises from the combined effects of grain migration and compaction,wherein the migration of both original and secondary crushed fine-grain particles blocks the seepage channels.Notably,grain composition influences the migration and transport properties of the grains.For samples composed of smaller grains,the apparent permeability demonstrates a transition from stability to decrease.In contrast,samples with larger grains experience a skip at the stability stage and directly enter the decrease stage,with a minor exception of a slight increase observed.Furthermore,a unique failure mode characterized by diameter shrinkage in the upper part of the sample is observed due to the combined effects of grain migration and in situ stress-induced compaction.These testing results contribute to a better understanding of the clogging mechanism caused by the coupled effects of grain migration and compaction during groundwater recharge in unconsolidated sandstone reservoirs used in groundwater-source heat pump systems.

Consolidation of high replacement ratio stone column-reinforced ground:Analytical solutions incorporating clogging effect

The utilization of stone columns has emerged as a popular ground improvement strategy,whereas the drainage performance can be adversely hampered by clogging effect.Despite the ample progress of calculation methods for the consolidation of stone column-improved ground,theoretical investigations into the clogging effect have not been thoroughly explored.Furthermore,it is imperative to involve the column consolidation deformation to mitigate computational error on the consolidation of composite ground with high replacement ratios.In this context,an analytical model accounting for the initial clogging and coupled time and depth-dependent clogging of stone columns is established.Then,the resulting governing equations and analytical solutions are obtained under a new flow continuity relationship to incorporate column consolidation deformation.The accuracy and reliability of the proposed model are illustrated by degradation analysis and case studies with good agreements.Subsequently,the computed results of the current study are juxtaposed against the existing models,and an in-depth assessment of the impacts of several crucial parameters on the consolidation behavior is conducted.The results reveal that ignoring column consolidation deformation leads to an overestimate of the consolidation rate,with maximum error reaching up to 16%as the replacement ratio increases.Furthermore,the initial clogging also has a significant influence on the consolidation performance.Additionally,the increment of depth and time-clogging factors a and b will induce a noticeable retardation of the consolidation process,particularly in the later stage.

Experimental Study on Clogging Characteristics of Silt Soft Soil in Nansha District of Guangzhou

The silt soft soil in Nansha District of Guangzhou was the softest soft soil in China. It had the characteristics of high natural water content, high compressibility, long consolidation time, and complex layered distribution of soil layers. These characteristics formed the clogging characteristics of silt soft soil, which greatly increased the construction difficulty and hindered the construction progress. Therefore, based on the basic physical and mechanical properties of silt soft soil in Nansha District of Guangzhou, this paper evaluated the clogging characteristics of three silt soft soil areas in Nansha District of Guangzhou through long-term permeability test, and carried out scanning electron microscope test to explore the influence of different parameters and microstructure on the clogging difficulty of silt soft soil. The results showed that the silt soft soil Zone I and Zone II (shallow layer) in Nansha District of Guangzhou were divided into slight siltation levels, and the silt soft soil Zone III (deep layer) was mild siltation level. Large pores were widely distributed in shallow silt soft soil, while the continuity of large pores in deep silt soft soil was poor. The migration of fine particles that failed to establish contact with surrounding particles in the soil blocks the small pores of seepage and thus produces siltation.

On the critical particle size of soil with clogging potential in shield tunneling

Shield tunneling is easily obstructed by clogging in clayey strata with small soil particles.However,soil clogging rarely occurs in strata with coarse-grained soils.Theoretically,a critical particle size of soils should exist,below which there is a high risk of soil clogging in shield tunneling.To determine the critical particle size,a series of laboratory tests was carried out with a large-scale rotary shear apparatus to measure the tangential adhesion strength of soils with different particle sizes and water contents.It was found that the tangential adhesion strength at the soilesteel interface gradually increased linearly with applied normal pressure.When the particle size of the soil specimen was less than 0.15 mm,the interfacial adhesion force first increased and then decreased as the water content gradually increased;otherwise,the soil specimens did not manifest any interfacial adhesion force.The amount of soil mass adhering to the steel disc was positively correlated with the interfacial adhesion force,thus the interfacial adhesion force was adopted to characterize the soil clogging risk in shield tunneling.The critical particle size of soils causing clogging was determined to be 0.15 mm.Finally,the generation mechanism of interfacial adhesion force was explored for soils with different particle sizes to explain the critical particle size of soil with clogging risk in shield tunneling.

Scaling and clogging treatment of aging tunnel drainage pipes in karst areas using eco-friendly acid agent

In karst areas,the drainage pipes of aging tunnels are prone to be clogged by precipitated carbonates,resulting in lining cracking and tunnel leaking.As a result,not only the driving safety will be deteriorated,but also the water pressure on the lining might also be elevated significantly.For the structural stability and service lifespan of old tunnels,it is of great importance to remove these precipitated carbonates in time.Traditional treatment methods are often destructive to some extent or not efficient enough.This study aims to experimentally develop an eco-friendly acid-based chemical cleaning method to remove carbonate precipitations efficiently.The proposed chemical cleaning agent is an aqueous solution with strong acidity,consisting of sulfamic acid,water,and additives.The factors affecting the cleaning efficiency include the acid solubility,temperature and flow rate of the cleaning agent,as well as additives.Elevating the solution temperature to 50
C or a flow rate of no less than 0.2 m/s can improve cleaning efficiency.Although the salt effect cannot work,1 wt%of polymaleic acid as a surfactant could further promote the cleaning rate.The cleaning efficiency will increase with the flow rate in a power function.The relatively low flow rate that improves the cleaning rate considerably can avoid highpressure-induced mechanical damage to tunnel drainpipes.The waste could be easily treated to acceptable levels using commercial sewage treatment products and can also be recycled in agriculture.With the chemical cleaning,the water pressure at the arch springing of the lining will reduce with the increased radius of transverse drainpipes in a power function.The proposed acid-based cleaning method,which is highly efficient,non-or low-destructive to aging tunnels,sufficiently safe for humans,and friendly enough to the environment,will offer a promising alternative to remove the precipitated carbonates in tunnel drainpipes efficiently.

Scalable Core–Sheath Yarn for Boosting Solar Interfacial Desalination Through Engineering Controllable Water Supply

Tailoring water supply to achieve confined heating has proven to be an effective strategy for boosting solar interfacial evaporation rates.However,because of salt clogging during desalination,a critical point of constriction occurs when controlling the water rate for confined heating.In this study,we demonstrate a facile and scalable weaving technique for fabricating core-sheath photothermal yarns that facilitate controlled water supply for stable and efficient interracial solar desalination.The core-sheath yarn comprises modal fibers as the core and carbon fibers as the sheaths.Because of the core-sheath design,remarkable liquid pumping can be enabled in the carbon fiber bundle of the dispersed superhydrophilic modal fibers.Our woven fabrics absorb a high proportion(92%)of the electromagnetic radiation in the solar spectrum because of the weaving structure and the carbon fiber sheath.Under one-sun(1 kW·m^(-2))illumination,our woven fabric device can achieve the highest evaporation rate(of 2.12kg·m^(-2)·h^(-1) with energy conversion efficiency:93.7%)by regulating the number of core-sheath yarns.Practical application tests demonstrate that our device can maintain high and stable desalination performance in a 5 wt%NaCl solution.

Flow and clogging in a horizontal silo with a rotary obstacle

The external perturbation applied to a silo and the placement of an immobile obstacle before an exit are two common and effective ways to diminish clogging in the hopper/silo flow.Here,we incorporate the local perturbation into a fixed obstacle,and experimentally explore the effects of a rotary obstacle on clogging and the flowing characteristics in the horizontal silo flow driven by a conveyor belt.Even with a low spin rate,the total blocking probability that a particle constructs a stable blocking arch with its neighbors significantly drops.Correspondingly,the average flow rate of the particles through the exit abruptly rises,at least 1 order of magnitude better than that with an immobile obstacle and approaching the flow rate of continuous flow.The rotation enhances the breakage of clogging arches,which is responsible for improving the flowability in the horizontal silo.In addition,there always exists an optimal obstacle position at which the total blocking probability is minimal and the average flow rate peaks,regardless of the spin rate.Finally,clogging is relieved with the increase of the driving velocity of the conveyor belt,showing a“fast is fast”effect that is opposite to the“fast is slow”effect in other systems such as crowd evacuation and gravity-driven hoppers.

Flow-Induced Clogging in Microfiltration Membranes: Numerical Modeling and Parametric Study

Microfiltration membrane technology has been widely used in various industries for solid-liquid separation. However, pore clogging remains a persistent challenge. This study employs (CFD) and discrete element method (DEM) models to enhance our understanding of microfiltration membrane clogging. The models were validated by comparing them to experimental data, demonstrating reasonable consistency. Subsequently, a parametric study was conducted on a cross-flow model, exploring the influence of key parameters on clogging. Findings show that clogging is a complex phenomenon affected by various factors. The mean inlet velocity and transmembrane flux were found to directly impact clogging, while the confinement ratio and cosine of the membrane pore entrance angle had an inverse relationship with it. Two clog types were identified: internal (inside the pore) and external (arching at the pore entrance), with the confinement ratio determining the type. This study introduced a dimensionless number as a quantitative clogging indicator based on transmembrane flux, Reynolds number, filtration time, entrance angle cosine, and confinement ratio. While this hypothesis held true in simulations, future studies should explore variations in clogging indicators, and improved modeling of clogging characteristics. Calibration between numerical and physical times and consideration of particle volume fraction will enhance understanding.

Effects of Hydraulic Loading of Vertical Flow Constructed Wetland Clogging

[Objective] The aim was to al eviate the constructed wetland clogging problems and to explore to the effects of hydraulic loading on wetland clogging. [Method] The experiment, through artificial soil columns, simulated vertical flow arti-ficial wetland, set four hydraulic load level at 50, 100, 150 and 200 cm/d, to identify the impact of hydraulic loading on wetland clogging and to explore the factors run-ning threshold. [Result] The results show that the different levels of hydraulic loading have greater impact; in the constructed wetland clogging process under high hy-draulic loading of 200 cm/d, the effective life was only six months, and the single factor can be speculated that the threshold of the hydraulic load should be at 100-150 cm/d; system can last for six months at low hydraulic loading and last for three months at medium hydraulic load. [Conclusion] The research provides references for wetland clogging experiments in future.

日本光电MK-6108血液细胞自动分析仪异常故障及排除

本文介绍了一例MK—6108分析仪发生同时报BBL与CLOG的错误现象及故障分析、处理。

Clogging processes caused by biofilm growth and organic particle accumulation in lab-scale vertical flow constructed wetlands

The accumulation of organic matter in substratum pores is regarded as an important factor causing clogging separately in the subsurface flow constructed wetlands.In this study,the developing process of clogging caused by biofilm growth or organic particle accumulation instead of total organic matter accumulation was investigated in two groups of lab-scale vertical flow constructed wetlands（VFCWs）,which were fed with glucose（dissolved organic matter） and starch（particulate organic matter） influent.Results showed that the growth of biofilms within the substratum pores certainly caused remarkable reduction of effective porosity,especially for the strong organic wastewater,whereas its influence on infiltration rate was negligible.It was implied that the most important contribution of biofilm growth to clogging was accelerating the occurrence of clogging.In comparison with biofilm growth,particles accumulation within pores could rapidly reduce infiltration rate besides effective porosity and the clogging occurred in the upper 0-15 cm layer.With approximately equal amount of accumulated organic matter,the effective porosity of the clogged layer in starch-fed systems was far less than that of glucose-fed systems,which indicated that composition and accumulation mode in addition to the amount of the accumulated organic matter played an important role in causing clogging.

Clogging behavior of submerged entry nozzles for Ti-bearing IF steel

The nozzle clogging behavior of Ti-bearing IF steel was studied by metallographic analysis,scanning electron microscopy（SEM）, energy dispersive spectroscopy（EDS）,and X-ray diffraction（XRD）.According to the experimental results,nozzle clogging primarily appears three layers.There are a lot of large-sized iron particles in the inner layer and mainly slag phase in the middle and outer layers.The principal clog constituents of the inner layer are loose alumina cluster inclusions and granular shaped alumina inclusions,containing iron particles. The clog constituents of the middle layer are mainly dendrite alumina inclusions.The primary phases existing in nozzle clogging are FeO·TiO2 and FeO·Al2O3 besidesα-Al2O3 and a-Fe.The FeO·TiO2 phases among the deposits adhere the deposits together firmly enough to lead to the inferior castability of Ti-bearing ultra low carbon steel compared with that of Ti-free low carbon Al-killed steel.

Tomato Yield and Quality and Emitter Clogging as Affected by Chlorination Schemes of Drip Irrigation Systems Applying Sewage Effluent

Chlorination has been recognized as an efficient and economically favorable method for treating clogging in drip emitters caused by biological growth during sewage application. Further important criteria for determining an optimal chlorination scheme are the different responses of crops to the chloride added into the soil through chlorination. During two seasons in 2008 and 2009, field experiments were conducted in a solar-heated greenhouse with drip irrigation systems applying secondary sewage effluent to tomato plants to investigate the influences of chlorine injection intervals and levels on plant growth, yield, fruit quality, and emitter clogging. Injection intervals ranging from 2 to 8 wk and injection concentrations ranging 2-50 mg L-1 of free chlorine residual at the end of the laterals were used. For the 2008 experiments, the yield from the treatments of sewage application with chlorination was 7.5% lower than the yield from the treatment of sewage application without chlorination, while the yields for the treatments with and without chlorination were similar for the 2009 experiments. The statistical tests indicated that neither the chlorine injection intervals and concentrations nor the interactions between the two significantly influenced plant height, leaf area, or tomato yield for both years. The qualities of the fruit in response to chlorination were parameter-dependent. Chlorination did not significantly influence the quality of ascorbic acid, soluble sugar, or soluble acids, but the interaction between the chlorine injection interval and the chlorine concentration significantly influenced the levels of soluble solids. It was also confirmed that chlorination was an effective method for reducing biological clogging. These results suggested that chlorination is safe for a crop that has a moderate sensitivity to chlorine, like tomato, and can maintain a high level of performance in drip irrigation systems applying sewage effluent.

Variation in hydraulic conductivity of fractured rocks at a dam foundation during operation

Characterizing the permeability variation in fractured rocks is important in various subsurface applications,but how the permeability evolves in the foundation rocks of high dams during operation remains poorly understood.This permeability change is commonly evidenced by a continuous decrease in the amount of discharge(especially for dams on sediment-laden rivers),and can be attributed to fracture clogging and/or hydromechanical coupling.In this study,the permeability evolution of fractured rocks at a high arch dam foundation during operationwas evaluated by inverse modeling based on the field timeseries data of both pore pressure and discharge.A procedure combining orthogonal design,transient flow modeling,artificial neural network,and genetic algorithm was adopted to efficiently estimate the hydraulic conductivity values in each annual cycle after initial reservoir filling.The inverse results show that the permeability of the dam foundation rocks follows an exponential decay annually during operation(i.e.K/K0=0.97e^(-0.59t)+0.03),with good agreement between field observations and numerical simulations.The significance of the obtained permeability decay function was manifested by an assessment of the long-term seepage control performance and groundwater flow behaviors at the dam site.The proposed formula is also of merit for characterizing the permeability change in riverbed rocks induced by sediment transport and deposition.

Biofilm structure and its influence on clogging in drip irrigation emitters distributing reclaimed wastewater

Using reclaimed wastewater for crop irrigation is a practical alternative to discharge wastewater treatment plant effluents into surface waters.However,biofouling has been identified as a major contributor to emitter clogging in drip irrigation systems distributing reclaimed wastewater.Little is known about the biofilm structure and its influence on clogging in the drip emitter flow path.This study was first to investigate the microbial characteristics of mature biofilms present in the emitters and the effect of flow path structures on the biofilm microbial communities.The analysis of biofilm matrix structure using a scanning electron microscopy（SEM） revealed that particles in the matrix of the biofilm coupled extracellular polysaccharides（EPS） and formed sediment in the emitter flow path.Analysis of biofilm mass including protein,polysaccharide,and phospholipid fatty acids（PLFAs） showed that emitter flow path style influenced biofilm community structure and diversity.The correlations of biofilm biomass and discharge reduction after 360 h irrigation were computed and suggest that PFLAs provide the best correlation coeffcient.Comparatively,the emitter with the unsymmetrical dentate structure and shorter flow path（Emitter C） had the best anti-clogging capability.By optimizing the dentate structure,the internal flow pattern within the flow path could be enhanced as an important method to control the biofilm within emitter flow path.This study established electron microscope techniques and biochemical microbial analysis methods that may provide a framework for future emitter biofilm studies.

Online forecasting model of tundish nozzle clogging

A nozzle clogging online forecasting model based on hydrodynamics engineering was developed, in which the actual flow rate was calculated from the mold width, thickness, and casting speed. There is a linear relationship between the theoretical flow rate and the slide gate opening ratio as the molten steel level, argon flow rate, and the top slag weight are kept constant, and the relationship can be obtained by regression of the data collected at the beginning of the first heat in each casting sequence when the nozzle clogging does not occur. Then, during the casting, the theoretical flow rate can be calculated at intervals of one second. Comparing the theoretical flow rate with the actual flow rate, the online nozzle clogging ratio can be obtained at intervals of one second. The computer model based on the conception of the nozzle clogging ratio can display the degree of the nozzle clogging intuitively.

Influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds

The influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds was studied using commercial code CFX4.3. The results indicate that clogging at the top part of the nozzle port not only increases the velocity of molten steel, but also enhances the wall shear stress, F number and heat flux. This clogging has the greatest effect on the behavior of molten steel. However, clogging at the top 1/3 of the nozzle only increases the velocity of molten steel and has little influence. Clogging at the bottom of the nozzle almost has no influence.

Lessons Learned from Aquifer Storage and Recovery (ASR) Systems in the United States

This paper is the result of a survey and analyses of available data from 204 Aquifer Storage and Recovery (ASR) sites in the United States. This ASR site survey included all active and inactive sites and collected both operational and construction details. The inactive sites are of particular interest here because these are the projects from which valuable lessons can often be learned. The intent of this paper is to examine the reasons for those projects that are terminated. Statistical analyses indicated that there were factors associated with terminated ASR projects: general geographic location (e.g., region), operational issue, storage cycle, casing material, and injection formation. The injection formation involves local geology and aquifer characteristics (i.e., whether the aquifer is leaky and/or unconfined, and if water can be displaced to surface water bodies or adjacent aquifers). Operational problems associated with inactive projects include well clogging, metals mobilization, a low percentage of recovery for injected water, and disinfection byproducts in the recovered water.

Influence of anode temperature on ignition performance of the IRIT4-2D iodine-fueled radio frequency ion thruster

This paper reports the ignition performance of the iodine-fueled radio frequency(RF)ion thruster(IRIT)at different anode temperaturesT_(a0).The experimental results show that the anode temperature plays important role on the ignition process of the IRIT.There were two characteristic temperatures related to the anode:the minimum ignition temperatureT_(i0)and the stable ignition temperatureT_(is),which were much lower than the pipeline temperature and the storage tank temperature.AtT_(a0)<T_(i0),it failed to discharge.WhenT_(i0)≤T_(a0)<T_(is),it was ignited with dramatical oscillations.AtT_(a0)≥T_(is),the discharge was stable in a large anode temperature range.The analysis showed that the different discharge phenomena at different anode temperatures were attributed to the change of iodine flow rate during the process of the iodine deposition-clogging and sublimation-clearing inside the thruster.The research helps improve the preheating design of the iodine-fueled electric thruster.

Numerical simulation of A1203 deposition at a nozzle during continuous casting

The effects of various factors, such as argon flow rate and slide gate opening ratio, on the alumina deposition rate were researched by the numerical simulation method. The pressure in the nozzle is significantly affected by argon flow rate and slide gate opening ratio. To keep positive pressure in the nozzle, the argon flow rate should be increased with a decrease in slide gate opening ratio. The effect of argon flow rate on the alumina deposition rate depends on the condition of opening ratio or casting speed. The effect of increasing the argon flow rate on the deposition rate is not obvious when the opening ratio is small. The A1203 deposition rate decreases significantly with an increase in argon flow rate when the argon flow rate is low, but it decreases slowly when the argon flow rate reaches a certain value. The alumina deposition rate is linear with alumina content at different slide gate opening ratios and argon flow rates. The observed thickness of the deposition layer at the bottom and outlet of a real clogged nozzle is almost equal to the result of the numerical simulation.