Employment of Two-Stage Oxygen Feeding to Control Temperature in a Downdraft Entrained-Flow Coal Gasifier

The traditional practice of employing a two-stage coal-fed gasification process is to feed all of the oxygen to provide a vigorous amount of combustion in the first stage but only feed the coal without oxygen in the second stage to allow the endothermic gasification process to occur downstream of the second stage. One of the merits of this 2-stage practice is to keep the gasifier temperature low downstream from the 2nd stage. This helps to extend the life of refractory bricks, decrease gasifier shut-down frequency for scheduled maintenance, and reduce the maintenance costs. In this traditional 2-stage practice, the temperature reduction in the second stage is achieved at the expense of a higher than normal temperature in the first stage. This study investigates a concept totally opposite to the traditional two-stage coal feeding practices in which the injected oxygen is split between the two stages, while all the coal is fed into the first stage. The hypothesis of this two-stage oxygen injection is that a distributed oxygen injection scheme can also distribute the release of heat to a larger gasifier volume and, thus, reduce the peak temperature distribution in the gasifier. The increased life expectancy and reduced maintenance of the refractory bricks can prevail in the entire gasifier and not just downstream from the second stage. In this study, both experiments and computational simulations have been performed to verify the hypothesis. A series of experiments conducted at 2.5 - 3.0 bars shows that the peak temperature and temperature range in the gasifier do decrease from 600?C - 1550?C with one stage oxygen injection to 950?C - 1230?C with a 60 - 40 oxygen split-injection. The CFD results conducted at 2.5 bars show that 1) the carbon conversion ratio for different oxygen injection schemes are all above 95%;2) H2 (about 70% vol.) dominates the syngas composition at the exit;3) the 80% - 20% case yields the lowest peak temperature and the most uniform temperature distribution along the gasifier;and 4) the 40% - 60% case produces the syngas with the highest HHV. Both experimental data and CFD predictions verify the hypothesis that it is feasible to reduce the peak temperature and achieve more uniform temperature in the gasifier by adequately controlling a two-stage oxygen injection with only minor changes of the composition and heating value of the syngas.

Mechanism and control of water seepage of vertical feeding borehole for solid materials in backflling coal mining

To solve the problem of water seepage of vertical feeding borehole for solid materials,we established the fluid-solid coupling dynamic model of groundwater flowing in rock mass adjacent to the vertical feeding borehole.Combining with the engineering geological conditions,we built a numeral model to study the influence rule of the aquifer hydraulic pressure and seepage location of feeding borehole on the amount of seepage with fnite element numerical method.The results show that the nonlinear relationship is presented among the amount of seepage,the seepage location and aquifer hydraulic pressure.The higher the aquifer hydraulic pressure is,the closer the distance between seepage location and aquifer is,and the faster the harmful levels of aquifer will grow.In practice,we calculated the allowable seepage of feeding borehole by the optimum moisture content and natural moisture content of backflling materials,and then determined the protection zone of feeding borehole,so the moisture content of backflling materials can be controlled within the scope of optimum moisture content.

Effect of UV-B radiation on the feeding behavior of the rotifer Brachionus plicatilis

Effect of UV - B radiation on the feeding behaviour of marine zooplankton is important to assessing the health harm of marine ecosystem due to the gradually enhanced UV - B radiation in air. However, there are a few studies on this topic. The feeding behavior of the rotifer, Brachionus plicatilis, under the treatment of UV - B radiation on five species of microalgae, i. e. , Chlorella sp. , Tetraselmis chuii, Isochrysis galbana Park 8701, Chaetoceros muelleri Lermumerman, and Nitzschia clostertum, was studied. The results showed that the filtering and feeding rates of the rotifer decreased significantly with the dose increase of UV - B radiation when fed with five species of microalgae respectively （ P 〈 0.05 ） which indicates UV - B radiation inhibits the feeding activities of the rotifer on microalage. The mixed culture experiments shows the rotifer preferred to feed Chlorella sp. , then C. muelleri, L galbana, N. clostertum and T. chuii in turn if without UV - B radiation. Under the highest dose of UV - B radiation treatment （2.70 kJ/m^2）, the rotifer preferred to feed C. muelleri, then Chlorella sp. , N. clostertum, L galbana and T. chuii in turn. Chlorella sp. , L galbana and C. muelleri became the more favorite foods of the rotifer while T. chuii and N. clostertum became less favorite foods. The change of feeding rate and feeding selectivity of zooplankton driven by the enhanced UV - B radiation will lead to the change in the structure of phytoplankton community.

A fuzzy control system of the variable construction for the feeding coal in the jigging process

This paper analyzes the detection means of the feeding coal in the jigging process, and puts forward a fuzzy control system of the variable construction in order to control the feeding coal. The fuzzy control system consists of three parts: bang-bang control, keep control and fuzzy control.

溶胶-凝胶水热合成法制备纳米CoAl_2O_4粉体

以仲丁醇铝和硝酸钴为原料,用溶胶-凝胶水热合成法制备了纳米CoAl2O4粉体,探讨了水热合成中前驱体的制备工艺条件,并用X射线衍射和扫描电镜等手段分析了水热系统中反应温度、反应时间对纳米CoAl2O4粉体的形成以及形貌的影响。结果表明:前驱体在250℃的水热系统中反应24h,能制备出较纯净、结晶完整、粒度均匀、粒径小、尖晶石结构的纳米CoAl2O4粉体,其平均粒度约为50～60nm。

Key technologies and equipment for a fully mechanized top-coal caving operation with a large mining height at ultra-thick coal seams

Thick and ultra-thick coal seams are main coal seams for high production rate and high efficiency in Chinese coal mines, which accounts for 44 % of the total minable coal reserve. A fully mechanized top-coal caving mining method is a main underground coal extraction method for ultra-thick coal seams. The coal extraction technologies for coal seams less than 14 m thick were extensively used in China. However, for coal seams with thickness greater than 14 m, there have been no reported cases in the world for underground mechanical extraction with safe performance, high efficiency and high coal recovery ratio. To deal with this case, China Coal Technology ＆ Engineering Group, Datong Coal Mine Group, and other 15 organizations in China launched a fundamental and big project to develop coal mining technologies and equipment for coal seams with thicknesses greater than 14 m. After the completion of the project, a coal extraction method was developed for top-coal caving with a large mining height, as well as a ground control theory for ultra-thick coal seams. In addition, the mining technology for top-coal caving with a large mining height, the ground support technology for roadway in coal seams with a large cross-section, and the prevention and control technology for gas and fire hazards were developed and applied. Furthermore, a hydraulic support with a mining height of 5.2 m, a shearer with high reliability, and auxiliary equipment were developed and manufactured. Practical implication on the technologies and equipment developed was successfully completed at the No. 8105 coal face in the Tashan coal mine, Datong, China. The major achievements of the project are summarized as follows： 1. A top-coal caving method for ultra-thick coal seams is proposed with a cutting height of 5 m and a top-coal caving height of 15 m. A structural mechanical model of overlying strata called cantilever beam-articulated rock beam is established. Based on the model, the load resistance of the hydraulic support with a large mining height for top-coal caving method is determined. With the analysis, the movement characteristics of the top coal and above strata are evaluated during top-coal caving operation at the coal face with a large mining height. Furthermore, there is successful development of comprehensive technologies for preventing and controlling spalling of the coal wall, and the top-coal caving technology with high efficiency and high recovery at the top-coal caving face with a large mining height. This means that the technologies developed have overcome the difficulties in strata control, top-coal caving with high efficiency and high coal recovery, and enabled to achieve a production rate of more than 10 Mtpa at a single top-coal caving face with a large mining height in ultra-thick coal seams; 2. A hydraulic support with 5.2 m supporting height and anti-rockburst capacity, a shearer with high reliability, a scraper conveyor with a large power at the back of face, and a large load and long distance headgate belt conveyor have been successfully developed for a top-coal caving face with large mining height. The study has developed the key technologies for improving the reliability of equipment at the coal face and has overcome the challenges in equipping the top-coal caving face with a large mining height in ultra-thick coal seams; 3. The deformation characteristics of a large cross-section roadway in ultra-thick coal seams are discovered. Based on the findings above, a series of bolt materials with a high yielding strength of 500-830 MPa and a high extension ratio, and cable bolt material with a 1 × 19 structure, large tonnage and high extension ratio are developed. In addition, in order to achieve a safe roadway and a fast face advance, installation equipment for high pre-tension bolt is developed to solve the problems with the support of roadway in coal seams for top-coal caving operation with a large mining height; 4. The characteristics of gas distribution and uneven emission at top-coal caving face with large mining height in ultra-thick coal seams are evaluated. With the application of the technologies of gas drainage in the roof, the difficulties in gas control for high intensive top-coal caving mining operations, known as ＂low gas content, high gas emission＂, are solved. In addition, large flow-rate underground mobile equipment for making nitrogen are developed to solve the problems with fire prevention and safe mining at a top-coal caving face with large mining height and production rate of more than 10 Mtpa. A case study to apply the developed technologies has been conducted at the No. 8105 face, the Tashan coal mine in Datong, China. The case study demonstrates that the three units of equipment, i.e., the support, shearer and scraper conveyor, are rationally equipped. Average equipment usage at the coal face is 92.1%. The coal recovery ratio at the coal face is up to 88.9 %. In 2011, the coal production at the No. 8105 face reached 10.849 Mtpa, exceeding the target of 10 Mtpa for a topcoal caving operation with large mining height performed by Chinese-made mining equipment. The technologies and equipment developed provide a way for extracting ultra-thick coal seams. Currently, the technologies and equipment are used in 13 mining areas in China including Datong, Pingshuo, Shendong and Xinjiang. With the exploitation of coal resources in Western China, there is great potential for the application of the technologies and equipment developed.

Investigation of Low Rank Coal Gasification in a Two-Stage Downdraft Entrained-Flow Gasifier

Low-rank coal contains more inherent moisture, high alkali metals (Na, K, Ca), high oxygen content, and low sulfur than high-rank coal. Low-rank coal gasification usually has lower efficiency than high-rank coal, since more energy has been used to drive out the moisture and volatile matters and vaporize them. Nevertheless, Low-rank coal comprises about half of both the current utilization and the reserves in the United States and is the largest energy resource in the United States, so it is worthwhile and important to investigate the low-rank coal gasification process. In this study, the two-stage fuel feeding scheme is investigated in a downdraft, entrained-flow, and refractory-lined reactor. Both a high-rank coal (Illinois No.6 bituminous) and a low-rank coal (South Hallsville Texas Lignite) are used for comparison under the following operating conditions: 1) low-rank coal vs. high-rank coal, 2) one-stage injection vs. two-stage injection, 3) low-rank coal with pre-drying vs. without pre-drying, and 4) dry coal feeding without steam injection vs. with steam injection at the second stage. The results show that 1) With predrying to 12% moisture, syngas produced from lignite has 538 K lower exit temperature and 18% greater Higher Heating Value (HHV) than syngas produced from Illinois #6. 2) The two-stage fuel feeding scheme results in a lower wall temperature (around 100 K) in the lower half of the gasifier than the single-stage injection scheme. 3) Without pre-drying, the high inherent moisture content in the lignite causes the syngas HHV to decrease by 27% and the mole fractions of both H2 and CO to decrease by 33%, while the water vapor content increases by 121% (by volume). The low-rank coal, without pre-drying, will take longer to finish the demoisturization and devolatilization processes, resulting in delayed combustion and gasification processes.

Non-isothermal oxidation of coal with Ce(NO3)3 and Cu(NO3)2 additives

Non-isothermal oxidation of brown coal with 5 wt% of Cu(NO3)2, 5 wt% of Ce(NO3)3 and {2.5 wt% Cu(NO3)2 + 2.5 wt% Ce(NO3)3} additives was studied. The introduction of additives was carried out by an incipient wet impregnation method to ensure uniform distribution of cerium and copper nitrates within the structure of coal powdery samples (according to SEM and EDX mapping). The samples reactivity was studied in an isothermal oxidation regime at 200 °C (1 h) and by DSC/TGA at 2.5 °C/min heating rate. The additives implementation was found to reduce significantly the oxidation onset temperature (△Ti = 20-55 °C), the samples oxidation delay time (△ti= 2-22 min) and overall duration of the oxidation process (△tc = 8-16 min). The additives efficiency could be graded in accordance with the activation on the coal oxidation in the following row: Cu(NO3)2 >{Cu(NO3)2 + Ce(NO3)3}> Ce(NO3)3. According to the mass spectroscopy, the obtained row of activation correlates well with the initial temperature of the studied nitrate's decomposition (from 190 to 223 °C). A presence of nitrates was found to change significantly the trend of heat release taking place during the oxidation of coal samples (according to DSC/TGA data). The influence of coal morphology and volatiles concern in initial sample on the parameters of the oxidation process was studied as well. Activation energy (Ea) of the coal oxidation was calculated using Coats-Redfern method. Maximum decrease in Ea from 69 to 58 kJ/mol was observed for the samples with Cu(NO3)2. Graphical abstract.

A novel suspension-floating-circulating fluidized combustion technology for coal slurry

A novel suspension-floating-circulating fluidized combustion technology is proposed for burning coal slurry fuel in traditional circulating ftuidized bed boilers （CFBB）. This technology can solve some existing problems in large- capacity CFBB burning coal slurry. The principles of the suspension-floating-circulating fluidized combustion technology were introduced in detail in this paper. A 130 t/h CFBB was retrofitted based on the technology, and the retrofitted system mainly includes a long-distance transport sub-system, a bed-material conveying sub-system with a wind-seal device invented by the authors, a superheater thermoregulation device using a novel temperature regulator, a return loop flu- idization facility, and a pneumatic ash conveying sub-system with sealed pump. The achieved performance of the retro- fitted CFBB shows that the thermal efficiency is 89.83 %, the combustion efficiency is 96.24 %, and the blending proportion of slurry is 94 %.

Association of TNF-α-238G/A and 308 G/A Gene Polymorphisms with Pulmonary Tuberculosis among Patients with Coal Worker’s Pneumoconiosis

Objectives Tumor necrosis factor-α （TNF-α） may play an important role in host＇s immune response to mycobacterium tuberculosis （M. tuberculosis） infection. This study was to investigate the association of TNF-α gene polymorphism with pulmonary tuberculosis （TB） among patients with coal worker＇s pneumoconiosis （CWP）. Methods A case-control study was conducted in 113 patients with confirmed CWP complicated with pulmonary TB and 113 non-TB controls with CWP. They were matched in gender, age, job, and stage of pneumoconiosis. All participants were interviewed with questionnaires and their blood specimens were collected for genetic determination with informed consent. The TNF-α gene polymorphism was determined with polymerase chain reaction of restriction fragment length polymorphism （PCR-RFLP）. Frequency of genotypes was assessed for Hardy-Weinberg equilibrium by chi-square test or Fisher＇s exact probability. Factors influencing the association of individual susceptibility with pulmonary TB were evaluated with logistic regression analysis. Gene-environment interaction was evaluated by a multiplieative model with combined OR. All data were analyzed using SAS version 8.2 software. Results No significant difference in frequency of the TNF-α-308 genotype was found between CWP complicated with pulmonary TB and non-TB controls （2,2=5.44, P=-0.07）. But difference in frequency of the TNF-α-308 A allele was identified between them （2,2-5.14, P=0.02）. No significant difference in frequencies of the TNF-α-238 genotype and allele （P=0.23 and P=0.09, respectively） was found between cases and controls either, with combined （GG and AA） OR of 3.96 （95% confidence interval of 1.30-12.09） at the -308 locus of the TNF-α gene, as compared to combination of the TNF-α-238 GG and TNF-α-308 GG genotypes. Multivariate-adjusted odds ratio of the TNF-α-238 GG and TNF-α-308 GA genotypes was 1.98 （95% CI of 1.06-3.71） for risk for pulmonary TB in patients with CWP. There was a synergic interaction between the TNF-a-308 GG genotype and body mass index （OR=4.92）, as well as an interaction between the TNF-α-308 GG genotype and history of BCG immunization or history of TB exposure. And, the interaction of the TNF-α-238 GG genotype and history of BCG immunization or TB exposure with risk for pulmonary TB in them was also indicated. Conclusions TNF-α-308 A allele is associated with an elevated risk for pulmonary TB, whereas TNF-α-238 A allele was otherwise.

Effect of ultrasonic irradiation on particle size,reagents consumption,and feed ash content in coal flotation

Ultrasonic waves have a lot of use in the particle surface cleaning.As flotation is one of the methods associated with surface properties,this paper investigates the effect of these waves on performance,particle size,reagents,and feed ash content in coal flotation.To accomplish this goal,coal samples in three size fractions,including coarse(-800 to+400μm),medium(-400 to+100 μm)and fine(-100μm)with various feed ash content.The flotation experiments were evaluated by process indexes such as yield,combustible recovery,and selectivity index.The results indicated the increasing of yield.The increasing was significant in medium size.Furthermore,the results showed that in presence of ultrasonic waves,the collector and frother consumption decreased.And also,applying ultrasonic waves would result more combustible recovery and selectivity index.The ash selectivity index had the highest impact for high feed ash content.

Effect of Mild-calcined Coal Gangue Additionon Hot Strength and Refractoriness Under Loadof Ultra Low Cement Castablesin Al_2O_3-SiO_2 System

This work explored the way to improve hot modulus q/＇ rupture （HMOR） and refractoriness under load （RUL） by adding mild-calcined coal gangue （MCG） in Al2O3 -SiO2 ultra low cement （ULC） castables, making use of the in-situ effect of the MCG during heating-up. The influence of respective additions of 5%, 10% and 1.5% of the MCG powders calcined at 700℃ was investigated on HMOR at 1400 ℃ and RUL of the castables. With increased addition of the MCG, HMOR and RUL become significantly enhanced. At 10% of the MCG addition, HMOR reaches 3 MPa, as compared to 0. 3 MPa in the case of no MCG addition. RUL of the specimens dried at 110 ℃for 24 h can be increased by some 270 ℃ with 10% of the MCG addition. RUL 0.11 the specimens preheated at 1 500℃ for 3 h maintains the growth trend with the MCG addition increasing. The microstructure of the heated castable samples was investigated by means of SEM. The in-situ formed needle-like and interlaced mullite in the matrix is contributive to the tmprovement.

Current Situation and Application in Coal-Generated Hydrocarbons

The characteristics and research methods of terrigenous organic hydrocarbon-generated source rock in coal measures are studied in this thesis. After abundance of organic matters, pyrolysis parameter of rocks and hydrocarbon generated capacity of macerals are basically discussed in coal measures of the Cretaceous Muleng-Chengzihe formation in Suibin depression in Sanjang basin, the hydrocarbon generated grade in coal-genera^ted source rock is ascertained in this depression. At last, we think that it is a main attack prospect in coal-genera^ted hydrocarbons study in the future to research the macerals of coal measures organic source rock and to build a criterion to classify the coal-generated hydrocarbons in Northeast region.

Investigation on the Structure of Chute-feed and Card Auto-leveller and Their Selection of Technological Processes

Based on the structure of chute - feed and autoleveHer, an analysis of their working principle and the verification of their practical production results have been carried out. Finally, the future investigation direetiom of chute - feed and card autuleveller are put forward.

固相萃取-GC-MS法测定饲料中的沙丁胺醇

沙丁胺醇(salbutamol),化学名称1-(4-羟基-3-羟甲基苯基)-2-(叔丁氨基)乙醇(结构式如图1所示),俗称舒喘宁,属于β-兴奋剂类药物的一种,临床上用于治疗支气管哮喘.同时沙丁胺醇同克伦特罗(瘦肉精)一样还具有提高饲料的转化率,促进动物生长的作用.但是,这种药物容易在动物内脏、组织中蓄积残留,有很大的副作用.……

裂解气相色谱-质谱法分离鉴定聚氨酯防水涂料中的煤焦油

建立了采用闪蒸裂解气相色谱-质谱测定固化后的聚氨酯防水涂料中的煤焦油的新方法。该方法方便快捷,无需对样品进行前处理,而且测定结果不受聚氨酯组分的干扰。该方法在建筑材料中有毒有害组分的分析检测方面有一定的应用价值。

淮北选煤厂Φ610-GT型煤泥旋流器应用探究

根据物料颗粒的受力情况,分析了煤泥旋流器直径、入料压力和矿粒直径之间的相关关系;通过对Φ610-GT型、SDMC500-1型煤泥旋流器进行单机检查试验,得到了二者浮沉试验数据,并对数据进行分析,得到了两种设备的降灰效果;此外,还对两种设备的可能偏差进行了计算,得出Φ610-GT型煤泥旋流器在现有条件下拥有更好的分选效果。

WGZ35/39-2型锅炉的节能技术改造与运行

通过对ＷＧＺ－ ３５／３９ － ２ 型锅炉进行节能技术改造，将燃烧器改为双向稳燃通用煤粉主燃烧器以及主送粉系统由乏气送粉改为热风送粉后，燃用低挥发分、高灰分的劣质烟煤时，燃烧稳定，飞灰可燃物含量降低，热效率提高，锅炉在６０ ％ 额定负荷下即可脱油稳定运行。

氢化物发生-原子荧光法在煤中砷测定的应用探析

从原子荧光的产生、原子荧光分析等方面阐述氢化物发生-原子荧光光谱法测定煤中砷的原理,并从激发光源、进样反应系统、原子化器、光学系统及检测系统剖析了原子荧光光谱仪的基本结构,以图示、化学方程式和公式推导的方式对氢化物发生-原子荧光光谱法在煤质分析中的应用进行解析,采用该方法对国家标准物质中砷含量进行测定结果准确性验证,指出氢化物发生-原子荧光光谱法对提高煤质检测水平有较大的意义。