Damage statistical mechanics model of horizontal section height in the top caving was constructed in the paper. The influence factors including supporting pressure, dip angle and characteristic of coal on horizontal s...Damage statistical mechanics model of horizontal section height in the top caving was constructed in the paper. The influence factors including supporting pressure, dip angle and characteristic of coal on horizontal section height were analyzed as well. By terms of the practice project analysis, the horizontal section height increases with the increase of dip angle β and thickness of coal seam M. Dip angle of coal seam β has tremendous impact on horizontal section height, while thickness of coal seam M has slight impact. When thickness of coal seam is below 10m, horizontal section height increases sharply. While thickness exceeds 15m, it is not major factor influencing on horizontal section height any long.展开更多
This paper seeks to enhance the understanding that the horizontal stresses build up and release during coal pillar loading and unloading(post-failure) drawing upon three decades of observations, geomechanical monitori...This paper seeks to enhance the understanding that the horizontal stresses build up and release during coal pillar loading and unloading(post-failure) drawing upon three decades of observations, geomechanical monitoring and numerical modeling in bump-prone U.S. mines. The focus is on induced horizontal stress in mine pillars and surrounding strata as highly stressed pillars punch into the roof and floor, causing shear failure and buckling of strata; under stiff stratigraphic units of some western US mines, these events could be accompanied by violent failure of pillar cores. Pillar punching eventually results in tensile stresses at the base of the pillar, facilitating transition into the post-failure regime; this transition will be nonviolent if certain conditions are met, notably the presence of interbedded mudstones with low shear strength properties and proper mine designs for controlling seismicity and dynamic loads. The study clearly shows high confining stress build-up in coal pillars resulting in up to twice higher peak vertical stress and high strain energy accumulations in some western US mines in comparison with peak stresses predicted using common empirical pillar design methods. It is the unstable release of this strain energy that can cause significant damage resulting from pillar dilation and ground movements. These forces are much greater than the capacity of most common internal support systems, resulting in horizontal stressinduced roof falls locally, in mines under unremarkable far-field horizontal stress. Attention should be placed on pillar designs as increasing support density may prove to be ineffective. This mechanism is analyzed using field measurements and generic finite-difference stress analyses. The study confirms the higher load carrying capacity of confinement-controlled coal seams in comparison with structurally controlled coal seams. Such significant differences in confining stresses are not taken into account when estimating peak pillar strength using most common empirical techniques such as those proposed by Bieniawski and Salamon. While using lower pillar strength estimates may be considered conservative,it underestimates the actual capacity of pillars in accumulating much higher stress and strain energies,misleading the designer and inadvertently diminishing mine safety. The role of induced horizontal stress in mine pillars and surrounding strata is emphasized in coal pillar mechanics of violent failure. The triggering mechanism for the violent events is sudden loss of pillar confinement due to dynamic loading resulting from failure of overlying stiff and strong strata. Evidence of such mechanism is noted in the field by observed red-dust at the coal-rock interfaces at the location of coal bumps and irregular, periodic caving in room-and-pillar mines quantified through direct pressure measurements in the gob.展开更多
Taking Adaohai Coal Mine as the example, underground pressure appearance laws of fully mechanized top coal slice caving on high-dipping and thick coal seams. Through site visit, theoretical analysis and discrete eleme...Taking Adaohai Coal Mine as the example, underground pressure appearance laws of fully mechanized top coal slice caving on high-dipping and thick coal seams. Through site visit, theoretical analysis and discrete element calculation, the research shows that, as the mining deepens, underground stress of lower sublevels is more obvious and higher than that of upper sublevels and is higher in the air return roadway than that in the air intake roadway in the area that is near to the top coal. Because the top coal is thick and gangue is caved above the support, underground pressure to the working face is relatively gentle. Immediate roof will mainly fall down along the floor. Main roof and the rock bed above the main roof will move to the mined out area along the fault in the early stage and then fall down with the mined out area later. In addition, roof pressure mainly periodically appears in two directions along the trend and the dip.展开更多
基金This work was financially supported by the National Natural Science fund of China (No.50274058).
文摘Damage statistical mechanics model of horizontal section height in the top caving was constructed in the paper. The influence factors including supporting pressure, dip angle and characteristic of coal on horizontal section height were analyzed as well. By terms of the practice project analysis, the horizontal section height increases with the increase of dip angle β and thickness of coal seam M. Dip angle of coal seam β has tremendous impact on horizontal section height, while thickness of coal seam M has slight impact. When thickness of coal seam is below 10m, horizontal section height increases sharply. While thickness exceeds 15m, it is not major factor influencing on horizontal section height any long.
文摘This paper seeks to enhance the understanding that the horizontal stresses build up and release during coal pillar loading and unloading(post-failure) drawing upon three decades of observations, geomechanical monitoring and numerical modeling in bump-prone U.S. mines. The focus is on induced horizontal stress in mine pillars and surrounding strata as highly stressed pillars punch into the roof and floor, causing shear failure and buckling of strata; under stiff stratigraphic units of some western US mines, these events could be accompanied by violent failure of pillar cores. Pillar punching eventually results in tensile stresses at the base of the pillar, facilitating transition into the post-failure regime; this transition will be nonviolent if certain conditions are met, notably the presence of interbedded mudstones with low shear strength properties and proper mine designs for controlling seismicity and dynamic loads. The study clearly shows high confining stress build-up in coal pillars resulting in up to twice higher peak vertical stress and high strain energy accumulations in some western US mines in comparison with peak stresses predicted using common empirical pillar design methods. It is the unstable release of this strain energy that can cause significant damage resulting from pillar dilation and ground movements. These forces are much greater than the capacity of most common internal support systems, resulting in horizontal stressinduced roof falls locally, in mines under unremarkable far-field horizontal stress. Attention should be placed on pillar designs as increasing support density may prove to be ineffective. This mechanism is analyzed using field measurements and generic finite-difference stress analyses. The study confirms the higher load carrying capacity of confinement-controlled coal seams in comparison with structurally controlled coal seams. Such significant differences in confining stresses are not taken into account when estimating peak pillar strength using most common empirical techniques such as those proposed by Bieniawski and Salamon. While using lower pillar strength estimates may be considered conservative,it underestimates the actual capacity of pillars in accumulating much higher stress and strain energies,misleading the designer and inadvertently diminishing mine safety. The role of induced horizontal stress in mine pillars and surrounding strata is emphasized in coal pillar mechanics of violent failure. The triggering mechanism for the violent events is sudden loss of pillar confinement due to dynamic loading resulting from failure of overlying stiff and strong strata. Evidence of such mechanism is noted in the field by observed red-dust at the coal-rock interfaces at the location of coal bumps and irregular, periodic caving in room-and-pillar mines quantified through direct pressure measurements in the gob.
基金Supported by the Scientific Research Business of China University of Mining ＆ Technology （Beijing） （2009QZ04） the National Natural Science Foundation of China （50974123）
文摘Taking Adaohai Coal Mine as the example, underground pressure appearance laws of fully mechanized top coal slice caving on high-dipping and thick coal seams. Through site visit, theoretical analysis and discrete element calculation, the research shows that, as the mining deepens, underground stress of lower sublevels is more obvious and higher than that of upper sublevels and is higher in the air return roadway than that in the air intake roadway in the area that is near to the top coal. Because the top coal is thick and gangue is caved above the support, underground pressure to the working face is relatively gentle. Immediate roof will mainly fall down along the floor. Main roof and the rock bed above the main roof will move to the mined out area along the fault in the early stage and then fall down with the mined out area later. In addition, roof pressure mainly periodically appears in two directions along the trend and the dip.
