Research on casing deformation prevention technology based on cementing slurry system optimization

The casing deformation prevention technology based on the optimization of cement slurry is proposed to reduce the casing deformation of shale oil and gas wells during hydraulic fracturing. In this paper, the fracture mechanism of hollow particles in cement sheath was firstly analyzed by discrete element method, and the effect of hollow particles in cement on casing deformation was investigated by laboratory experiment method. Finally, field test was carried out to verify the improvement effect of the casing deformation based on cement slurry modification. The results show that the formation displacement can be absorbed effectively by hollow particles inside the cement transferring the excessive deformation away from casing. The particles in the uncemented state provide deformation space during formation slipping. The casing with diameter of 139.7 mm could be passed through by bridge plug with the diameter of 99 mm when the mass ratio of particle/cement reaches 1:4. According to the field test feedback, the method based on optimization of cement slurry can effectively reduce the risk of casing deformation, and the recommended range of hollow microbeads content in the cement slurry is between 15% and 25%.

Influence of filler characteristics on particle removal in fluid catalytic cracking slurry under an alternating electric field

The characteristics of the packing material under an alternating electric field are an important factor in the removal of FCCS particles.In this study,the electric field distribution of a separation unit consisting of packed spheres under an alternating electric field is simulated,and the movement mechanism of catalyst particles is analysed.An"effective contact point"model is derived to predict the adsorption of filler contact points on catalyst particles under the alternating electric field,and the model is validated by simulations and experiments.The numerical calculation and experimental results indicate that the electrical properties of the filler spheres,the filler angleθ,and the frequency f of the alternating electric field affect the adsorption of catalyst particles.As the frequency of the electric field increases,the particle removal efficiency of the high-conductivity filler(silicon carbide)increases and then settles,and the separation efficiency of the low-conductivity filler(glass,zirconia)is not sensitive to the change in electric field frequency.

Preparation and Electrochemical Performance Study of Catalytic Cracking Oil Slurry-based Porous Carbon Materials

Catalytic cracking oil slurry is a by-product of catalytic cracking projects,and the efficient conversion and sustainable utilization of this material are issues of continuous concern in the petroleum refining industry.In this study,oxygen-enriched activated carbon is prepared using a one-step KOH activation method with catalytic cracking oil slurry as the raw material.The as-prepared oil slurry-based activated carbon exhibits a high specific surface area of 2102 m^(2)/g,welldefined micropores with an average diameter of 2 nm,and a rich oxygen doping content of 32.97%.The electrochemical performance of the nitrogen-doped porous carbon is tested in a three-electrode system using a 6 mol/L KOH solution as the electrolyte.It achieves a specific capacitance of up to 230 F/g at a current density of 1 A/g.Moreover,the capacitance retention rate exceeds 89%after 10000 charge and discharge cycles,demonstrating excellent cycle stability.This method not only improves the utilization efficiency of industrial fuel waste but also reduces the production cost of supercapacitor electrode materials,thereby providing a simple and effective strategy for the resource utilization of catalytic cracking oil slurries.

A Gasification Technology to Combine Oil Sludge with Coal-Water Slurry:CFD Analysis and Performance Determination

The development of more environment-friendly ways to dispose of oil sludge is currently regarded as a hot topic.In this context,gasification technologies are generally seen as a promising way to combine oil sludge with coal–water slurry(CWS)and generate resourceful fuel.In this study,a novel five-nozzle gasifier reactor was analyzed by means of a CFD(Computational fluid dynamic)method.Among several influential factors,special attention was paid to the height-to-diameter ratio of the gasifier and the mixing ratio of oil sludge,which are known to have a significant impact on the flow field,temperature distribution and gasifier performances.According to the numerical results,the optimal height-to-diameter ratio and oil mixing ratio are about 2.4:1 and 20%,respectively.Furthermore,the carbon conversion rate can become as high as 98.55%with the hydrolysis rate reaching a value of 53.88%.The consumption of raw coal and oxygen is generally reduced,while the effective gas production is increased to 50.93 mol/%.

Current collectors’ effects on the electrochemical performance of LiNi_(0.6)Co_(0.2)Mn_(0.2)O_(2) suspension electrodes for lithium slurry battery

Take after the advantages of lithium-ion battery (LIB) and redox flow battery (RFB), semi-solid flow battery (SSFB) is a promising electrochemical energy storage device in renewable energy utilization. The flowable slurry electrode realizes decouple of energy and power density, while it also brings about new challenge to SSFBs, electron transport between active material and the out circuit. In this consideration, three types of current collectors (CCs) are applied to study the resistance and electrochemical performances of slurry cathodes within pouch cells for the first time. It proves that the electronic resistance (Re) between slurry electrode and the CC plays a decisive role in SSFB operation, and it is so large when Al foil is adopted that the cell cannot even work. Contact angle between Ketjen black (KB) slurry without active material (AM) and the CC is a preliminarily sign for the Re, the smaller the angle, the lower the resistance, and the better electrochemical performance of the cell.

Enhanced recovery of high-purity Fe powder from iron-rich electrolytic manganese residue by slurry electrolysis

Iron-rich electrolytic manganese residue(IREMR)is an industrial waste produced during the processing of electrolytic metal manganese,and it contains certain amounts of Fe and Mn resources and other heavy metals.In this study,the slurry electrolysis technique was used to recover high-purity Fe powder from IREMR.The effects of IREMR and H2SO4 mass ratio,current density,reaction temper-ature,and electrolytic time on the leaching and current efficiencies of Fe were studied.According to the results,high-purity Fe powder can be recovered from the cathode plate,and the slurry electrolyte can be recycled.The leaching efficiency,current efficiency,and purity of Fe reached 92.58%,80.65%,and 98.72wt%,respectively,at a 1:2.5 mass ratio of H2SO4 and IREMR,reaction temperature of 60℃,electric current density of 30 mA/cm^(2),and reaction time of 8 h.In addition,vibrating sample magnetometer(VSM)analysis showed that the coercivity of electrolytic iron powder was 54.5 A/m,which reached the advanced magnetic grade of electrical pure-iron powder(DT4A coercivity standard).The slurry electrolytic method provides fundamental support for the industrial application of Fe resource recovery in IRMER.

Rapid prediction of flow and concentration fields in solid-liquid suspensions of slurry electrolysis tanks

Slurry electrolysis(SE),as a hydrometallurgical process,has the characteristic of a multitank series connection,which leads to various stirring conditions and a complex solid suspension state.The computational fluid dynamics(CFD),which requires high computing resources,and a combination with machine learning was proposed to construct a rapid prediction model for the liquid flow and solid concentration fields in a SE tank.Through scientific selection of calculation samples via orthogonal experiments,a comprehensive dataset covering a wide range of conditions was established while effectively reducing the number of simulations and providing reasonable weights for each factor.Then,a prediction model of the SE tank was constructed using the K-nearest neighbor algorithm.The results show that with the increase in levels of orthogonal experiments,the prediction accuracy of the model improved remarkably.The model established with four factors and nine levels can accurately predict the flow and concentration fields,and the regression coefficients of average velocity and solid concentration were 0.926 and 0.937,respectively.Compared with traditional CFD,the response time of field information prediction in this model was reduced from 75 h to 20 s,which solves the problem of serious lag in CFD applied alone to actual production and meets real-time production control requirements.

Study on the rheology of coal-oil slurries during heating at high pressure

Using the self-developed viscosity measuring device, the viscosity variations of coal-oil slurries with temperature increasing during coal-oil co-processing were studied. The results show that the viscosity of coal-oil slurries prepared by different kinds of oil varies differently during heating. The viscosity of the coal-oil slurry prepared by the catalytic cracking slurry （FCC） generally decreases during heating. However, the viscosity of the coal-oil slurry prepared by the high-temperature coal tar （CT） will peak at 338 ℃ during heating. The differences in viscosity variations of coal-oil slurries are analyzed. In addition to the temperature, the properties of the solvents and coal are the main influencing factors. Because the used coal contains a large number of polar functional groups, the swelling behavior of the coal in polar solvent （CT） is stronger than that in non-polar solvent （FCC）. The swelling effect of the coal can result in the appearance of the viscosity peak. Therefore, before 100 ~C, the solvent molecules entering into the coal pores is the main influencing factor of coal-oil slurries viscosity variations. After 100 ℃, the increasing of particle size of coal particles is the main influencing factor of coal-oil slurries viscosity variations.

Impacts of solid physical properties on the performances of a slurry external airlift loop reactor integrating mixing and separation

Solid physical properties are vital for the design, optimization, and scale-up of gas–liquid–solid multiphase reactors. The complex and interactional effects of the solid physical properties, including particle diameter, density, wettability, and sphericity, on the hydrodynamic behaviors in a new external airlift loop reactor(EALR) integrating mixing and separation are decoupled in this work. Two semi-empirical equations are proposed and validated to predict the overall gas holdup and liquid circulating velocity satisfactorily, and then the individual influence of such solid physical properties is further investigated. The results demonstrate that both the overall gas holdup in the riser and the liquid circulating velocity in the downcomer increase with the contact angle, but decrease with particle size, density, and sphericity.Additionally, the impact of the particle size on the liquid circulating velocity is also profoundly revealed on a micro-level considering the particle size distribution. Moreover, the axial solid concentration distribution is discussed, and the uniformity of the slurry is described by the mixing index of the solid particles. The results show that a more homogeneous mixture can be achieved by adding finer particles other than attaining violent turbulence. Therefore, this work lays a foundation for the design, scale-up, and industrialization of the EALRs.

Kinetic mechanism of copper extraction from methylchlorosilane slurry residue using hydrogen peroxide as oxidant

Copper was extracted from methylchlorosilane slurry residue by a direct hydrogen peroxide leaching method.A number of experimental parameters were analyzed to determine the extraction efficiency of copper.The extraction efficiency of copper reached 98.5%under the optimal leaching conditions,such as the hydrogen peroxide concentration of 1.875 mol·L^(-1),the leaching temperature of 323 K,the liquid–solid ratio of 20 ml·g^(-1),and the stirring speed of 300 r·min^(-1).The leaching kinetics of the copper extraction process was then described by the shrinking core model.There were two stages.The first stage was controlled by chemical reactions,while the second stage was controlled by interface transfer and product layer diffusion.The activation energy and kinetic control equations were determined,as well as an explanation of the leaching mechanism of copper extraction based on kinetic analysis and materials characterization.Copper resources can be recovered from the methylchlorosilane slurry residue efficiently and inexpensively with the methods used in this study.

Physical model investigation on effects of drainage condition and cement addition on consolidation behavior of tailings slurry within backfilled stopes

Estimation of stressses within the tailings slurry during self-weight consolidation is a critical issue for cost-effective barricade design and efficient backfill planning in underground mine stopes.This process requires a good understanding of self-weight consolidation behaviors of the tailings slurry within practical stopes,where many factors can have significant effects on the consolidation,including drainage condition and cement addition.In this paper,the prepared tailings slurry with different cement contents(0,4.76wt%,and 6.25wt%)was poured into1.2 m-high columns,which allowed three drainage scenarios(undrained,partial lateral drainage near the bottom part,and full lateral drainage boundaries)to investigate the effects of drainage condition and cement addition on the consolidation behavior of the tailings slurry.The consolidation behavior was analyzed in terms of pore water pressure(PWP),settlement,volume of drainage water,and residual water content.The results indicate that increasing the length of the drainage boundary or cement content aids in PWP dissipation.In addition,constructing an efficient drainage boundary was more favorable to PWP dissipation than increasing cement addition.The final stable PWP on the column floor was not sensitive to cement addition.The final settlement of uncemented tailings slurry was independent of drainage conditions,and that of cemented tailings slurry decreased with the increase in cement addition.Notably,more pore water can drain out from the cemented tailings slurry than the uncemented tailings slurry during consolidation.

Mechanical properties and microstructural evolution of rheocast A356 semi-solid slurry prepared by annular electromagnetic stirring

Nowadays,having an effective technique in preparing semi-solid slurries for rheocasting process seems to be an essential requirement.In this study,semi-solid slurry of A356 aluminum alloy was prepared by three-phase annular electromagnetic stirring(A-EMS)technique under different conditions.The effects of stirring current,pouring temperature and stirring time on microstructural evolution,mean particle size,shape factor and solid fraction were investigated.The rheocasting process was carried out by using a drop weight setup and to inject the prepared semi-solid slurry in optimal conditions into the step-die cavity.The filling behavior and mechanical properties of parts were studied.Microstructural evolution showed that the best semi-solid slurry which had fine spherical particles with the average size of~27μm and a shape factor of~0.8 was achieved at the stirring current of 70 A,melt pouring temperature of 670℃,and stirring time of 30 s.Under these conditions,the step-die cavity was completely filled at die preheating temperature of 470℃.The hardness increases by decreasing step thickness as well as die preheating temperature.Moreover,the tensile properties are improved at lower die preheating temperatures.The fracture surface,which consists of a complex topography,indicates a typical ductile fracture.

Kinetics of Selective Hydrogenation of PAHs from FCC Slurry Extract over Ni-W/γ-Al_(2)O_(3) Catalyst

The selective hydrogenation of polycyclic aromatic hydrocarbons(PAHs)from fluid catalytic cracking(FCC)slurry extract was conducted in a batch reactor over aγ-Al_(2)O_(3)-supported bimetallic Ni-W catalyst.For the Ni-W/γ-Al_(2)O_(3) catalyst,the experiment run was divided into three processes according to the reaction conditions used:(1)the absence of hydrogenation as both temperature and pressure increased;(2)the desulfurization of FCC slurry extract under a fixed pressure as the temperature increased;and(3)the selective hydrogenation of PAHs when both pressure and temperature remained constant.The hydrogen consumption could be accurately calculated from the Redlich–Kwong equation of state.The results for the removal of PAHs with hydrogenation displayed an excellent fit to the first-order kinetics.The apparent activation energy was determined to be 20.80 kJ/mol.

Multi-criteria comparative analysis of the pressure drop on coal gangue fly-ash slurry at different parts along an L-shaped pipeline

Disposing of coal gangue and fly-ash on the surface is a risky method with tremendous potential catastrophic consequences for the environment.Backfill mining is a promising practice for turning those hazardous wastes into functional backfill materi-als.Unfortunately,how to efficiently deliver the slurry to the desired places remains under-researched.To address this issue,the computational fluid dynamics software Fluent was used in the current study in addition to a laboratory rheological test to simulate the impact of various parameters on the evolution of pressure at a particular section of the pipeline.Furthermore,the response surface method was employed to investigate how the various components and their corresponding influencing weights interact to affect the pressure drop.This study demonstrates that the pressure drop of the slurry is highly influenced by slurry concentration,speed,and pipe diameter.While conveying speed is the main component in the bend section,pipe diameter takes over in the horizontal and vertical pipe sections.

Development of a High-Temperature Thixotropic Cement Slurry System

Cementing carbonate reservoirs is generally a difficult task.The so-called thixotropic cement slurry has gained considerable attention in this regard as it can help tofix some notable problems.More precisely,it can easilyfill the leakage layer;moreover,its gelling strength can grow rapidly when pumping stops,thereby increasing the resistance to gas channeling,effectively preventing this undesired phenomenon in many cases.High-temperature thixotropic cement slurry systems,however,are still in an early stage of development and additional research is needed to make them a viable option.In the present study,using a self-developed composite high-temperature thixotropic additive as a basis,it is shown that the compressive strength can be adjusted by tuning the proportion of silica sand,the high-temperature retarder,fluid loss additive and dispersant(compatible with the thixotropic additive).According to the tests,the developed high-temperature thixotropic cement slurry system has a 14 d compressive strength of 29.73 MPa at 150°C,and a thickening time of 330 min when the dosage of retarder is 2%.At the same time,the rheological property,water loss,permeability,water separation rate,and settlement stability of the cement slurry system meet the requirements of cementing construction.

Efect of Micro Abrasive Slurry Jet Polishing on Properties of Coated Cemented Carbide Tools

Owing to the popularization of coating technology, physical Vapor Deposition (PVD) coated tools have become indispensable in the cutting process. Additionally, the post-treatment of coated tools applied to industrial production can efectively enhance the surface quality of coating. To improve the processing performance of coated tools, micro abrasive slurry jet (MASJ) polishing technology is frst applied to the post-treatment of coated tools. Subsequently, the efects of process parameters on the surface quality and cutting thickness of coating are investigated via single-factor experiments. In the experiment, the best surface roughness is obtained by setting the working pressure to 0.4 MPa, particle size to 3 μm, incidence angle to 30°, and abrasive mass concentration to 100 g/L. Based on the results of the single-factor experiments, combination experiments are designed, and three types of coated tools with diferent surface qualities and coating thicknesses are obtained. The MASJ process for the post-treatment of coated tools is investigated based on a tool wear experiment and the efects of cutting parameters on the cutting force and workpiece surface quality of three types of cutting tools. The result indicates that MASJ machining can efectively improve the machining performance of coated tools.

Numerical simulation study on multiphase flow pattern of hydrate slurry

The research on the multiphase flow characteristics of hydrate slurry is the key to implementing the risk prevention and control technology of hydrate slurry in deep-water oil and gas mixed transportation system.This paper established a geometric model based on the high-pressure hydrate slurry experimental loop.The model was used to carry out simulation research on the flow characteristics of gas-liquid-solid three-phase flow.The specific research is as follows:Firstly,the effects of factors such as slurry flow velocity,hydrate particle density,hydrate particle size,and hydrate volume fraction on the stratified smooth flow were specifically studied.Orthogonal test obtained particle size has the most influence on the particle concentration distribution.The slurry flow velocity is gradually increased based on stratified smooth flow.Various flow patterns were observed and their characteristics were analyzed.Secondly,increasing the slurry velocity to 2 m/s could achieve the slurry flow pattern of partial hydrate in the pipeline transition from stratified smooth flow to wavy flow.When the flow rate increases to 3 m/s,a violent wave forms throughout the entire loop.Based on wave flow,as the velocity increased to 4 m/s,and the flow pattern changed to slug flow.When the particle concentration was below 10%,the increase of the concentration would aggravate the slug flow trend;if the particle concentration was above 10%,the increase of the concentration would weaken the slug flow trend,the increase of particle density and liquid viscosity would weaken the tendency of slug flow.The relationship between the pressure drop gradients of several different flow patterns is:slug flow>wave flow>stratified smooth flow.

Simulation Research on Coal-Water Slurry Gasification of Oil-Based Drill Cuttings Based on Fluent

In this paper,based on Fluent software,a five-nozzle gasifier reactor was established to simulate the gasification process of oil-based drill cuttings coal-water slurry.The influence of concentration and oxygen/carbon atomic ratio on the gasification process of oil-based drill cuttings coal-water slurry was investigated.The results show that when the oxygen flow is constant,the outlet temperature of gasifier decreases,the content of effective gas increases,and the carbon conversion rate decreases with the increase of concentration;When the ratio of oxygen to carbon atoms is constant,the effective gas content rises and the temperature rises with the increase of the concentration,and the carbon conversion rate reaches the maximum value when the concentration of oil-based drill cuttings coal-water slurry is 65%;When the concentration is constant,the effective gas content decreases and the outlet temperature rises with the increase of the oxygen/carbon atom ratio,and the carbon conversion rate reaches 99.80%when the oxygen/carbon atom ratio is 1.03.It shows that this method can effectively decompose the organic matter in oilbased drill cuttings and realize the efficient and cooperative treatment of oil-based drill cuttings.

A Comprehensive Method for the Optimization of Cement Slurry and to Avoid Air Channeling in High Temperature and High-Pressure Conditions

Air channeling in the annulus between the casing and the cement sheath and/or between the cement sheath and formation is the main factor affecting the safe operation of natural gas wells at high temperatures and pressures.Prevention of this problem requires,in general,excellent anti-channeling performances of the cement sheath.Three methods to predict such anti-channeling performances are proposed here,which use the weightless pressure of cement slurry,the permeability of cement stone and the volume expansion rate of cement sheath as input parameters.Guided by this approach,the anti-channeling performances of the cement slurry are evaluated by means of indoor experiments,and the cement slurry is optimized accordingly.The results show that the dangerous transition time of the cement slurry with optimized dosage of admixture is only 76 min,the permeability of cement stone is 0.005 md,the volume shrinkage at final setting is only 0.72%,and the anti-channeling performances are therefore maximized.The effective utilization of the optimized cement slurry in some representative wells(LD10–1-A1 and LD10–1-A2 in LD10–1 gas field)is also discussed.

A Comprehensive Review of the Influence of Heat Exchange Tubes on Hydrodynamic,Heat,and Mass Transfer in Bubble and Slurry Bubble

Bubble and slurry bubble column reactors(BCRs/SBCRs)are used for various chemical,biochemical,and petro-chemical applications.They have several operational and maintenance advantages,including excellent heat and mass transfer rates,simplicity,and low operating and maintenance cost.Typically,a catalyst is present in addition to biochemical processes where microorganisms are used to produce industrially valuable bio-products.Since most applications involve complicated gas-liquid,gas-liquid-solid,and exothermic processes,the BCR/SBCR must be equipped with heat-exchanging tubes to dissipate heat and control the reactor’s overall performance.In this review,past and very recent experimental and numerical investigations on such systems are critically dis-cussed.Furthermore,gaps to befilled and critical aspects still requiring investigation are identified.