Urinary levels of nickel and chromium associated with dental restoration by nickel-chromium based alloys

This paper aims to investigate if the dental restoration of nickel-chromium based alloy(Ni-Cr) leads to the enhanced excretions of Ni and Cr in urine.Seven hundred and ninety-five patients in a dental hospital had single or multiple Ni-Cr alloy restoration recently and 198 controls were recruited to collect information on dental restoration by questionnaire and clinical examination.Urinary concentrations of Ni and Cr from each subject were measure by graphite furnace atomic absorption spectrometry.Compared to the control group,the urinary level of Ni was significantly higher in the patient group of < 1 month of the restoration duration,among which higher Ni excretions were found in those with either a higher number of teeth replaced by dental alloys or a higher index of metal crown not covered with the porcelain.Urinary levels of Cr were significantly higher in the three patient groups of <1,1 to <3 and 3 to <6 months,especially in those with a higher metal crown exposure index.Linear curve estimations showed better relationships between urinary Ni and Cr in patients within 6-month groups.Our data suggested significant increased excretions of urinary Ni and Cr after dental restoration.Potential short- and long-term effects of Ni-Cr alloy restoration need to be investigated.

Influence of chromium on the initial corrosion behavior of low alloy steels in the CO_2–O_2–H_2S–SO_2 wet–dry corrosion environment of cargo oil tankers

The influence of Cr on the initial corrosion behavior of low-alloy steels exposed to a CO2–O2–H2S–SO2 wet–dry corrosion environment was investigated using weight-loss measurements, scanning electron microscopy, N2 adsorption tests, X-ray diffraction analysis, and electrochemical impedance spectroscopy. The results show that the corrosion rate increases with increasing Cr content in samples subjected to corrosion for 21 d. However, the rust grain size decreases, its specific surface area increases, and it becomes more compact and denser with increasing Cr content, which indicates the enhanced protectivity of the rust. The results of charge transfer resistance(Rct) calculations indicate that higher Cr contents can accelerate the corrosion during the first 7 d and promote the formation of the enhanced protective inner rust after 14 d; the formed protective inner rust is responsible for the greater corrosion resistance during long-term exposure.

Experimental study of electron beam welded titanium alloy to chromium bronze joint with a vanadium sheet

Electron beam welding experiment of titanium alloy to chromium bronze with a vanadium filler metal was carried out. Microstructure of the joint was observed by optical microscopy and scanning electron microscopy. Tensile strength of the joint was evaluated. The fracture surface of the joint was also analyzed. The results showed that the addition of vanadium filler metal reduced the brittleness of joint by increasing the amount of vanadium-based solid solution in the weld. But the melting point of vanadium.filler metal was so high that large heat input was needed to completely melt the filler metal. Thus, a large amount of interfacial compounds were produced. The tensile strength of joint was 280 MPa with a brittle fracture mode.

Effects of extrusion on chromium precipitation in Cu-Cr alloy

Cu Cr alloys containing Cr from 0.14% to 2.0% in mass were prepared as foils for TEM observation before and after being extruded. The results show that before extrusion, the spheroid or short bar chromium disperse in copper matrix of the Cu Cr alloy, and the relationship between Cu and Cr follows the Nishiyama Wasserman (NW) relationship, i.e. [110] Cu ∥ [001] Cr . After the Cu Cr alloy was extruded at 860 ℃, dark field image along (224) Cu clearly shows that there are precipitated chromium particles in copper matrix. However, the SADP comprises only (112) Cu zone.

LASER ALLOYING ON CHROMIUM-COATED SURFACE OF NODULAR CAST IRON

１ＩＮＴＲＯＤＵＣＴＩＯＮＬａｓｅｒａｌｏｙｉｎｇｔｒｅａｔｍｅｎｔｍａｋｅｓｌａｓｅｒｂｅａｍｈｅａｔ，ａｎｄｍｅｌｔｏｒｓｏｌｉｄｉｆｙｍｅｔａｌｓｕｒｆａｃｅｑｕｉｃｋｌｙｂｙｈｅａｔｉｎｇｃｏｎｄｕｃｔｉｏｎｉｎｉｔｓｏｗｎｂｏｄｙ．Ｄｕｅｔ...

Chromium Electroplating of Aluminium Alloys Using Electroless Nickel as Underlayer

The growing demand for chromium coated aluminium components especially for the automotive industry is due to their favourable physical properties (density, strength to weight ratio etc.). However, their frequent use under harsh environmental conditions renders them corrosion sensitive and consequently they need to be protected. An approach that has been applied in industry is to directly electroplate nickel onto aluminium substrate prior to a top metallic finish;however, in components with complex geometry, certain areas could become exposed to corrosion attack due to poor surface coverage during plating. In this study, a modified electroless nickel undercoat was applied to pre-treated aluminium alloys prior to duplex nickel and chromium plating with a view to enhance corrosion resistance, improve coating adherence and durability, and overall, to achieve substrate protection. Hexavalent and trivalent chromium were applied to pre-treated Al 1050 and Al 6061 following electroless nickel deposition, and plating performance was assessed by surface and corrosion techniques, while durability was measured by scratch, adhesion and hardness tests. Overall, while chromium plating with an electroless nickel undercoat did not improve corrosion resistance or hardness of the materials, it provided an additional protective layer for the substrate with a potential for longer term durability.

Study of a New Chromium-Free Conversion Coating Formed on ZnAl Alloy

A new chromium-free conversion film was obtained on surface of a ZnAl alloy by chemical conversion process. Influence of the additives in treating solution containing cerium salt on the corrosion protection of the conversion film formed on zinc alloy was investigated. Corrosion tests and electrochemical measurements in sodium chloride solution were performed . The microstructure and composition of the coatings were examined by means of SEM, EDS and XRD. It was found that the corrosion protection capabilities of the conversion film are markedly increased with the cerium nitride plus additives (hydrogen fluoride acid and an organic inhibitor) treating process. The modified conversion film is an organic/inorganic composite coating and is much more corrosion resistant than the conventional chromate conversion coating and the single cerium conversion coating.

Effect of Ti-V-Nb-Mo addition on microstructure of high chromium cast iron

The effects of trace additions of multi-alloying elements （Ti, Nb, V, Mo） on carbides precipitation and ascast microstructure of eutectic high chromium cast iron containing 2.85wt.%C and 31.0wt.%Cr were investigated from thermodynamic and kinetic considerations. The thermodynamic calculations show that Ti and Nb exist in the multi-alloying system in the forms of TiC and NbC. The formation of VC during the solidification is not feasible from the thermodynamic consideration. XRD analysis shows that the V exists in alloy compounds （VCr2C2, VCrFes）. The first precipitated high melting point particles （TIC, NbC） can act as the heterogeneous substrate of M7C3 carbides, which results in significant refinement of the M7C3 carbides. After the addition of alloying elements, C atom diffusion is hindered due to the strong affinities of the strong carbide forming elements for carbon, which decreases the growth rate of carbides. The combined roles of the increase of nucleation rate and the decrease of carbides growth rate lead to the finer microstructure.

Synthesis of nanocrystalline NiCrC alloy feedstock powders for thermal spraying by cryogenic ball milling

Nanocrystalline NiCrC alloy powders with a qualified particle size distribution for thermal spraying were synthesized using the cryogenic ball milling （cryomilling） method. The morphology, microstructure, size distribution, and phase transformation of the powders were characterized by scanning electron microscopy （SEM）, laser scattering for particle size analysis, X-ray diffraction （XRD）, and transmission electron microscopy （TEM）. After cryomilling for 20 h, the average grain size of the as-milled powders approached a constant value of 30 nm by XRD measurement. The average particle size slightly increased from 17.5 to 20.3 μm during the 20-h milling. About 90vol% of the powders satisfied the requirement for thermal spraying with the particle dimension of 10-50 μm, and most of the powders exhibited spherical morphology, which were expected to have good fluidity during thermal spraying. The Cr2O3 phase formed during the cryornilling process as revealed in the XRD spectra, which was expected to enhance the thermal stability of the as-milled powders during the followed thermal spraying or other heat treatment.

A Cu-Cr alloy with nano and microscale Cr particles produced in a water-cooled copper mold

Microstructures have profound effects on the hardness and strength of Cu-Cr alloys. The microstructures of a Cu-Cr alloy cast in a water-cooled copper mold were studied in the present work. The scanning electron microscopy （SEM） results show that there are the copper matrix saturated with chromium, spherical precipitates of chromium separated from liquid phase during cooling before the initiation of so- lidification, and a eutectic phase in grain boundary areas. To investigate the effect of age-hardening treatment on the microstructures and properties of the material, some samples were subsequently age-hardened in a salt bath and investigated by transmission electron microscopy （TEM）. The results show that coherent precipitates with the diameter of 11 nm are detectable in the samples before and after the age-hardening stage. Of course, the volume fraction of coherent precipitates is higher after the aging process.

Microstructural Stability of a Single Crystal Superalloy DD8 during Thermal Exposure

Microstructural stability of a nickel base single crystal alloy DD8 has been investigated.Standard heat treated specimen showed good microstructural stability at 950℃.While under the as-cast condition,a kind of rod-like phase precipitated in the interdendritic region of as-cast specimen during thermal exposure.The phase,which has bcc structure,was enriched with Cr.Thermo-calc also predicted precipitation of a bcc phase at around 950℃.The Cr-rich bcc phase was considered asα-Cr and formed due to the segregation of Cr under the as-cast condition.

OXIDATION OF A TWO-PHASE Cu-75Cr ALLOY IN AIRAT 700-900℃

The cormsion in air of a two-phase Cu-75Cr alloy was studied at 700-900℃. Thealloy cormded nearly parabolically at 700-800℃, but at 900℃ its instantaneousparabolic mte constant decreased with time. The scales were complex and consistedof an outermost layer of copper oxide generally followed bg a layer of the double ox-ide Cu2 Cr2 O4 sometimes containing particles of unoxidized chromium surmunded bya chromia layer. An innermost layer of chromia was also observed in some cases.Finally metallic copper was al8o frequently mixed with chromia particles. No Cr de-pletion was observed in the alloy close to the inteffoce with the scale. In any case,this alloy was not able to form an exclusive continuous protective chromia layer. Thespecial cormsion behavior Of this alloy is typical of two-phase binary systems with alange solubility gaP in which the outwaof dthesion fiux of the most-reactive componentin the alloy is strongly reduced and may be inswncient to fOrm a protective externallayer of the cormsponding oxide. In paTticular, the presence of particles of Cr withina double oxide layer is very unusual and is allowed only for the kinetic reason.

Solidification microstructure formation in HK40 and HH40 alloys

The microstructure formation processes in HK40 and HH40 alloys were investigated through JmatP ro calculations and quenching performed during directional solidification. The phase transition routes of HK40 and HH40 alloys were determined as L → L ＋ γ→ L ＋ γ ＋ M_7C_3 →γ ＋ M_7C_3 →γ ＋ M_7C_3 ＋ M_（23）C_6→γ ＋ M_（23）C_6 and L → L ＋ δ→ L ＋ δ ＋ γ→ L ＋ δ ＋ γ ＋ M_（23）C_6→δ ＋ γ ＋ M_（23）C_6, respectively. The solidification mode was determined to be the austenitic mode（A mode） in HK40 alloy and the ferritic–austenitic solidification mode（FA mode） in HH40 alloy. In HK40 alloy, eutectic carbides directly precipitate in a liquid and coarsen during cooling. The primary γ dendrites grow at the 60° angle to each other. On the other hand, in HH40 alloy, residual δ forms because of the incomplete transformation from δ to γ. Cr_（23）C_6 carbide is produced in solid delta ferrite δ but not directly in liquid HH40 alloy. Because of carbide formation in the solid phase and no rapid growth of the dendrite in a non-preferential direction, HH40 alloy is more resistant to cast defect formation than HK40 alloy.

Yixunite and Damiaoite—A Twin of New Native Alloys of Indium and Platinum from the Yanshan Mountains

Yixunite and damiaoite Were found in a cobalt- and copper-bearing platinum ore vein of a contact metasomatic deposit. The chief ore minerals are bornite, chalcopyrite, magnetite and carrollite. The platinum minerals include moncheite, sperrylite, daomanite, cobalt malanite and cooperite. Yixunite and damiaoite occur as immiscible globules, 1.0 to 2.0 mm in diameter. Yixunite is always in the central part of a globule. It is opaque with metallic lustre, bright white colour and black streak. HM = 5.8; VHN50 = 634 kg/mm2 (573-681 kg/ mm2); insoluble in HCl, HNO3, HF or H3PO4; no cleavage; no magnetism. Density is hard to measure because of small grain size. Calculated density = 18.21 g/cm3. Reflective colour is bright white with a yellowish tint. Isotropic. The mean analytical results (ranges) (%) are: Pt 82.8 (81.8-83.6), In 16.4(15.6-17.1) and total 99.2. The empirical formula (based on 4 atoms) is Pt2.993 In1.007 . The five strongest lines of X-ray diffraction (hkl, d,I) are 111, 2.30 (100); 200, 1.99 (60); 202, 1.411 (40);311, 1.203 (80); 222, 1.151(40). Space group: Pm3m with a =0.3988(3) nm and Z= 1. Damiaoite occurs as single globules or was exsolved from yixunite. Opaque with metallic lustre; bright white colour with black streak; HM = 5.3; VHN50 = 485 kg/mm2 (434-529 kg/mm2); insoluble in HC1, HNO3, HF or H3PO4; cleavage: no; magnetism: no. Density: hard to measure because of small grain size. Calculated density = 10.95 g/ cm3. Reflective colour is bright white with a yellowish tint. Isotropic. The mean analytical results (ranges) (%) are Pt 45.6 (45.4-46.0), In 53.5 (52.4-53.9), total 99.1. The empirical formula (based on 3 atoms) is Pt0.002 In1.998. The six strongest lines of X-ray diffraction (hkl.d,I) are 220,2.25 (100); 311,1.92 (60); 400,1.59 (60); 422,1.299 (80); 440,1.125 (60); 620,1.006 (70). Space group: Fm3m with a = 0.6364 (3) nm and Z = 4.

Electroplating process of amorphous Fe-Ni-Cr alloy

A novel process of electroplating amorphous Fe Cr Ni alloy in chloride aqueous solution with Fe(Ⅱ), Ni(Ⅱ) and Cr(Ⅲ) was reported. Couple plasma atomic emission spectrometry (ICP AES), X ray diffractometry(XRD), scanning electronic microscopy(SEM), microhardness test and rapid heating cooling method were adopted to detect the properties of the amorphous Fe Ni Cr deposit, such as composition, crystalline structure, micrograph, hardness, and adherence between deposit and substrate. The effects of the operating parameters on the electrodeposit of the amorphous Fe Ni Cr alloy were discussed in detail. The results show that a 8.7?μm thick mirror like amorphous Fe Ni Cr alloy deposit, with Vicker’s hardness of 530 and composition of 45%～55% Fe, 33%～37% Ni, 9%～23% Cr was obtained by electroplating for 20?min at room temperature(10～30?℃), cathode current 10～16?A/dm 2, pH=1.0～3.0. The XRD patterns show that there only appears a broad hump around 2 θ of 41?°～47?°for the amorphous Fe Ni Cr alloy deposit, while the SEM micrographs show that the deposit contains only a few fine cracks but no pinholes.

Alloy600的性能及其在石化装置中的选用

Alloy600是一种镍-铬-铁合金,其中镍元素的成分限值大于等于72.0%,铬的含量在14.0%~17.0%之间,铁的含量在6.0%~10.0%之间。Alloy600不仅具有非常强的抗氯化物应力裂变腐蚀能力,且在零下、室温及高温时都具有很好的机械性能和可加工性,使其可以进行各种冷,热加工,机加工和焊接。Alloy600的优秀性能使其广泛应用于石化工程装置中。

Properties of CuCr contact materials with low chromium content and fine particles

The voltage withstanding capability and electric conductivity of CuCr contact materials with low chromium content and fine Cr particles were studied. The results show that the withstanding voltage has little relation with the Cr content for the melted casting CuCr alloy within 15%29% Cr content, and that the electric conductivity of the alloy increases with the decreasing of Cr content.

WIDE-BAND LASER CLADDING: WEAR AND CORROSION RESISTANCE OF A Ni-BASED ALLOY

A novel wide-band laser cladding system, with high rate of cladding, has been developed in the present work. The system mainly consisted of a 5kW CO2 laser, an automatic powder feeder and a wide-band scanning rotative polygon mirror which can produce a linear or rectangular focused laser beam. Using this system, a Ni-Cr-Si-B alloy powder was cladded on the surface of type 321 austenitic stainless steel in order to improve its wear and corrosion resistance. The pitting corrosion, high temperature oxidation and wear tests were conducted in order to evaluate the properties of the laser cladded layer. The results demonstrated that the cladded layer can significantly improve the adhesive wear and pitting corrosion resistance of the substrate. Moreover, the cladded layer exhibited good oxidation resistance, which is almost the same as that of GMR-235D Ni-based superalloy.

THE RESEARCH OF THE HIGHER TOUGHNESS HIGH CHROMIUM WHITE CAST IRONAS CAST

Inthispaper the effectof alloying on thestructure and properties of high chromium whilecastiron hasbeen research. Theresultsobtained show thatthealloyingcan changethe matrix structure,buttheeffecton thecarbidesislittle when thereisless Ccontent and less Cr con tent,and the alloyingcan changethe morphology and distribution ofthecarbides,which pro duce granular and bar likecarbides.Theimpacttoughness of the high chromium whitecast ironascast may definitely amount to above 12 1J/cm2 ～14 5J/cm2 ,higher by 35 % ～ 143 % than com mon high chromium whitecastiron .