A new approach for selecting best development face ventilation mode based on G1-coefficient of variation method

The current popular methods for decision making and project optimisation in mine ventilation contain a number of deficiencies as they are solely based on either subjective knowledge or objective information.This paper presents a new approach to rank the alternatives by G1-coefficient of variation method.The focus of this approach is the use of the combination weighing,which is able to compensate for the deficiencies in the method of evaluation index single weighing.In the case study,an appropriate evaluation index system was established to determine the evaluation value of each ventilation mode.Then the proposed approach was used to select the best development face ventilation mode.The result shows that the proposed approach is able to rank the alternative development face ventilation mode reasonably,the combination weighing method had the advantages of both subjective and objective weighing methods in that it took into consideration of both the experience and wisdom of experts,and the new changes in objective conditions.This approach provides a more reasonable and reliable procedure to analyse and evaluate different ventilation modes.

A preliminary study of the variation of phytoplankton absorption coefficients in the northern South China Sea

The temporal and spatial variabilities of phytoplankton absorption coefficients （a ph （λ）） and their relationships with physical processes in the northern South China Sea were examined, based on in situ data collected from two cruise surveys during May 14 to 25, 2001 and November 2 to 21, 2002. Significant changes in the surface water in a ph values and B/R ratios （a ph （440）/a ph （675）） were observed in May, which were caused by a phytoplankton bloom on the inner shelf stimulated by a large river plume due to heavy precipitation. This is consistent with the observed one order of magnitude elevation of chlorophyll a and a shift from a pico/nano dominated phytoplankton community to one dominated by micro-algae. Enhanced vertical mixing due to strengthened northeast monsoon in November has been observed to result in higher surface a ph （675） （0.002–0.006 m-1 higher） and less pronounced subsurface maximum on the outer shelf/slope in November as compared with that in May. Measurements of a ph and B/R ratios from three transects in November revealed a highest surface a ph （675） immediately outside the mouth of the Zhujiang （Pearl） River Estuary, whereas lower a ph （675） and higher B/R ratios were featured in the outer shelf/slope waters, demonstrating the respective influence of the Zhujiang River plume and the oligotrophic water of the South China Sea. The difference in spectral shapes of phytoplankton absorption （measured by B/R ratios and bathochromic shifts） on these three transects infers that picoprocaryotes are the major component of the phytoplankton community on the outer shelf/slope rather than on the inner shelf. A regional tuning of the phytoplankton absorption spectral model （Carder et al., 1999） was attempted, demonstrating a greater spatial variation than temporal variation in the lead parameter a 0 （λ）. It was thus implicated that region-based parameterization of ocean color remote sensing algorithms in the northern South China Sea was mandatory.

Terrain Rendering LOD Algorithm Based on Improved Restrictive Quadtree Segmentation and Variation Coefficient of Elevation

Aiming to deal with the difficult issues of terrain data model simplification and crack disposal,the paper proposed an improved level of detail(LOD)terrain rendering algorithm,in which a variation coefficient of elevation is introduced to express the undulation of topography.Then the coefficient is used to construct a node evaluation function in the terrain data model simplification step.Furthermore,an edge reduction strategy is combined with the improved restrictive quadtree segmentation to handle the crack problem.The experiment results demonstrated that the proposed method can reduce the amount of rendering triangles and enhance the rendering speed on the premise of ensuring the rendering effect compared with a traditional LOD algorithm.

New SST correction method from multi-satellite based on the coefficient of variation

In remote sensing sea surface temperature （SST）, the traditional fusion method is used to compute the dot product of a subjective weight vector with a satellite measurement vector, while the result requires validation by field measurement. However, field measurement that relative to the satellite measurement is very sparse, many information may not be verified. A relative objective weight vector is constructed by using the limited field measurement, which is based on coefficient of variation method. And then it make an application of the data fusion by the weighted average method in the SST data. fuse SST data with the weighted average method. In this way, some posteriori information can be added to the fusion process. The model reduces the dependence on verification, and some of the satellite measurement can be handled without corresponding to the field measurement, and the fusion result matches transfer errors theory.

Study on the Driving Forces of Rocky Desertification in Guizhou Province Based on Variation Coefficient Method

[Objective] The aim was to study the driving forces of rocky desertification in Guizhou Province. [Method] Based on GIS and RS technology, the main driving forces of rocky desertification in Guizhou Province were analyzed by means of correlation analysis and variation coefficient method, and then the distribution of rocky desertification in Guizhou Province was assessed synthetically. [Result] The main driving forces of rocky desertification in Guizhou Province were vegetation cover, rainfall, peasant income and gradient which were obviously correlative with rocky desertification; from theoretical distribution, rocky desertification was the most serious in Bijie, southwest Guizhou, southern Guizhou and northeastern Guizhou, and the theoretical distribution of rocky desertification in Bijie was severer than its current situation, which showed that construction of ecological function area in Bijie restrained the development of rocky desertification effectively; the good consistency between theoretical and current distribution of rocky desertification revealed that the study method was feasible. [Conclusion] The study could provide theoretical references for the practical control of rocky desertification.

Grading Standards of the Coefficient of Variation in the Electronic Raw Silk Size Testing

In order to shorten the difference between the raw silk size grading standards of the world and that of China, to quicken the step of the electronic raw silk testing process, the distribution of the coefficient of variation (CV50m%) of the raw silk size in the electronic testing and the development of the new standards are studied according to the sampling and grading theory. By the theoretical deduction and the simulating experiments, the distribution of the coefficient of variation of the raw silk size is given, and the grading scheme whose quality index is the coefficient of variation(CV50m%)of the raw silk size and the grading precisions of all grades are proposed. Moreover, the rightness and the feasibility of the grading scheme are testified by the sampling and grading simulation.

Predicting GM(1,N) Model for the Coefficient of Variation of Hectometer Yarn's Weight

The Coefficient of Variation(CV)of hectometer yarn's weight is one of the guidelines to evaluate its intrinsic quality.In the spinning manufacturing,the control of cotton yarn's weight unevenness is accomplished mainly in terms of a spot-check on semi-product and a succedent adjust in process parameters during spinning based on technicians' experience.However,it is theoretically believed among manufacturers that with fixed technical levels and parameters in the spinning process,the quality parameters of assorted cotton have a certain influence on the CV.In order to find out a rule of the influence that assorted cotton has on the CV,a GM(1,N)model,correlated raw cotton's quality parameter with the CV,has firstly been developed according to the modeling theory of grey system,and then been applied in the designing step to predict the CV.It has been approved by practical modeling and validation that the model could fit preferably an accrual CV value,and provide a method of quantitative predicting analysis for textile manufacturers to design cotton yarn's quality.

The coefficient of variation representing the non-uniformity of the strain field and its implication to detect earthquake precursor

Before the major earthquake or rock damage occurs,it is often accompanied by a sudden change in the degree of non-uniformity of the strain field.In order to find a stronger non-uniformity signal before the rock failure,the coefficient of variation(Cv)is examined and reformed in this study.We test the Cv calculation way of the"normal-abnormal"model proposed in the previous studies.Based on the analysis of the physical process of rock failure and its relationship to the shear strain field,we construct a new way to calculate the Cv value.The variation of shear strain field on rock sample with the increase of stress is obtained by the digital speckle correlation method(DSCM).The new Cv value calculation way is used to study the non-uniformity of the spatial distribution for the shear strain field.The results show that this Cv calculation way can get more obvious abnormal signals.When the number of observation points are limited,the specific distribution of points can increase the signal strength,which may provide reference for the research on precursor detection of earthquakes.

Seasonal variation of evapotranspiration,Priestley-Taylor coefficient and crop coefficient in diverse landscapes

Priestley-Taylor equation(PT)and the Penman-Monteith equation(PM)are commonly used methods for regional evapotranspiration monitoring,using the PT coefficient(α_(a))and PM crop/vegetation coefficient(K_(c)).This paper investigates the seasonal changes inα_(a)and K_(c)at five sites in Australia and China,to understand the relation-ship between environmental conditions and evapotranspiration when applying different evaporation estimation methods.The research shows that higher actual evapotranspiration does not lead to higherα_(a)and K_(c)values.α_(a)and K_(c)perform similarly in cropland and forest environments in both China and Australia.Bothα_(a)and K_(c)continuously increase to a peak during the growing season and then decrease to their lowest values during the winter season.Considering K_(c)’s similar performance toα_(a)and its greater data processing requirements,K_(c)has few advantages for estimating regional evapotranspiration.Applying the Priestley-Taylor equation with a regional𝛼indicator will enhance the accuracy and reduce the workload when estimating regional evapotranspiration for similar landcover types based on remote sensing.

Application of Equality Test of Coefficients of Variation to the Heteroskedasticity Test

The presence of heteroskedasticity in a considered regression model may bias the standard deviations of parameters obtained by the Ordinary Least Square (OLS) method. In this case, several hypothesis tests on the model under consideration may be biased, for example, CHOW’s coefficient stability test (or structural change test), Student’s t-test and Fisher’s F-test. Most of the heteroscedasticity tests in the literature are based on the comparison of variances. Despite the multiplication of equality tests of coefficients of variation (CVs) that have appeared in the literature, to our knowledge, the first and only use of the coefficient of variation in the detection of heteroskedasticity was offered by Li and Yao in 2017. Thus, this paper offers an approach to determine the existence of heteroskedasticity by a test of equality of coefficients of variation. We verify by a Monte Carlo robustness and performance test that our method seems even better than some tests in the literature. The results of this study contribute to the exploitation of the statistical measurement of CV dispersion. They help technicians economists to better verify their hypotheses before making a scientific decision when making a necessary forecast, in order to contribute effectively to the economic and sustainable development of a company or enterprise.

CLASSICAL LIMITS FOR THE COEFFICIENT OF VARIATION FOR THE NORMAL DISTRIBUTION

The exact classical limits for the coefficient of variation c for the normal distribution are derived. The hand-calculating approximated classical limits for c having high accuracy are given to meet practical engineering needs. Using Odeh and Owen's computational method and Brent's algorithm, the tables for the r-upper exact classical limits of coefficient of variation for normal distribution are calculated for the different confidence coefficient y, the sample size n=1(1)30,40,60,120, the sample coefficient of variation c=0.01(0.01)0.20. It is shown that if n<8,c<0.20, then the V -upper exact classical limits cu for c are slightly higher than the exact fiducial limits cu,F for c if. n>8, c<0.02,then cu-cu,f<5x10-6

Effect of Variation of the Coefficient of Friction on the Temperature at the Level of the Fault Lips

Earth’s crust is an anisotropic and purely heterogeneous medium, which is justified by existence of different discontinuities;our study aims to show the effect of the variation of coefficient of friction on the evolution of temperature and its impact on seismic forecasting. In this work, we are model in 2D the variation of thermal energy and temperature produced by friction at the level of fault lip as function of depth of the seismic focus and at different value of time. Earthquakes are born when the energy accumulated by friction at the level of fault is suddenly released causing damage, sometimes noticeable on the surface of earth (macroseisms), and sometimes not at all noticeable on the surface of earth (microseisms), then energy which occurs before is important to forecasting earthquake. Assuming that coefficient of friction is variable, our results have enabled us to highlight the fact that, the greater the coefficient of friction, more the temperature increases, although the temperature profile increase over time but not linearly reflecting the presence of different asperities and discontinuities zone;slip generated at the level of fault occur a variation of temperature on specific points called roughness in common agreement with the literature. A large part of energy produced by friction is dissipated in heat causing a local increases in temperature which a very short duration and called flash contact temperature, and that despite the fact that the temperature evolved in time and space, it all converged towards a perfectly distinguishable fixed point.

A VARIATIONAL METHOD FOR COMPUTING POTENTIAL COEFFICIENTS USING DIFFERENT TYPES OF GRAVIMETRIC DATA

In this paper,a variational method is presented for solving theclassical gravimetric,satellite gravimetric and satellite altimetric mixed typeboudary value problem to obtain the potential coefficients.According to thisprinciple,classical gravimetric data（height measured by geometric levelling orheight triangulation）,satellite gravimetric data（height measured by satellitegeodesy technique）and satellite altimetric data can be used jointly to calculate thepotential coefficients.

Improving seismic interpretation: a high-contrast approximation to the reflection coefficient of a plane longitudinal wave

Linearized approximations of reflection and transmission coefficients set a foundation for amplitude versus offset（AVO） analysis and inversion in exploration geophysics.However,the weak properties contrast hypothesis of those linearized approximate equations leads to big errors when the two media across the interface vary dramatically.To extend the application of AVO analysis and inversion to high contrast between the properties of the two layers,we derive a novel nonlinearized high-contrast approximation of the PP-wave reflection coefficient,which establishes the direct relationship between PPwave reflection coefficient and P-wave velocities,S-wave velocities and densities across the interface.（A PP wave is a reflected compressional wave from an incident compressional wave（P-wave）.） This novel approximation is derived from the exact reflection coefficient equation with Taylor expansion for the incident angle.Model tests demonstrate that,compared with the reflection coefficients of the linearized approximations,the reflection coefficients of the novel nonlinearized approximate equation agree with those of the exact PP equation better for a high contrast interface with a moderate incident angle.Furthermore,we introduce a nonlinear direct inversion method utilizing the novel reflection coefficient equation as forward solver,to implement the direct inversion for the six parameters including P-wave velocities,S-wave velocities,and densities in the upper and lower layers across the interface.This nonlinear inversion algorithm is able to estimate the inverse of the nonlinear function in terms of model parameters directly rather than in a conventional optimization way.Three examples verified the feasibility and suitability of this novel approximation for a high contrast interface,and we still could estimate the six parameters across the interface reasonably when the parameters in both media across the interface vary about 50%.

Individual Variation in Growth in Sea Cucumber Apostichopus japonicus(Selenck) Housed Individually

The exceptionally large individual growth variation has been previously recognized in several sea cucumber cohorts. However, there is a lack of information regarding the mechanism of such individual differences. In this study, the sea cucumber Apostichopusjaponicus （Selenka） was reared individually in order to eliminate possible effects of social interaction, stocking density, etc. The results showed that there were substantial differences in growth among the sea cucumber individuals during the 100-day experiment. The special growth rate of the sea cucumber individuals differed by up to three folds （from 0.40% to 1.01%）, and the coefficient of variation in body weight increased from 12.04% to 40.51%. The final wet body weight, food intake and food conversion efficiency for each sea cucumber were generally positively correlated with their initial wet body weight （P〈0.05）. Energy budget of the animals showed that the food energy spent on respiration was much greater （about four folds） but energy deposited for growth was much less for （initially） smaller than for larger A. japonicus. The present result implies that there are obvious genetic differences among the sea cucumber individuals, largely accounting for the individual growth variation of the cohort sea cucumber. These results will provide some basic data for promoting selective breeding and fanning of the sea cucumber.

Genetic variation of wood tracheid traits and their relationships with growth and wood density in clones of Pinus tabuliformis

To improve wood quality for pulpwood industries, it is important to examine not only wood density but also its components, especially tracheid characteristics. We studied genetic variations in the following tracheid traits by earlywood （EW） and latewood （LW）： tracheid length （TL）, double wall thickness （WT）, radial lumen diameter （R_D1）, tangential lumen diameter （T_D1）, radial central diameter （R_D2）, and tangential central diameter （T_D2）. We also studied the relationship with the following growth traits： diameter at breast height （DBH）, height （H）, crown breadth south-north axis （NSC）, crown breadth east-west axis （EWC）, ring width （RW）, latewood percentage （LWP）, and wood density （WD）. All sample materials were collected from a 33-year old clonal seed orchard of Pinus tabuliformis Carr. Genetic variation among clones was moderate for all tracheid traits, 9.49-26.03%. Clones significantly affected WT, R_D1, R_D2, T_D1, T_D2, and the two ratios WT/R_D1 and TL/T_D2 in EW but had no effects in LW. Clones significantly affected TL in LW but had no effects in EW. H2/C was higher in LW （0.50） than in EW （0.20） for TL, while H 2/C was higher in EW （0.27-0.46） for other tracheid traits and the two ratios （TL/T_D2 and WT/R_D1） than in EW （0.06-0.22）. WD and TL were significantly positively correlated, but WT and TL were negatively correlated both at individual and clone levels; all tracheid diameters and the four ratio values （EW_WT/ R_D1, LW WT/R_D1, EW_TL/T_D2 and LW_TL/ T_D2）, were strongly positively correlated with DBH, H, NSC, WEC and RW, and strongly negatively correlated with WD both at individual and clone levels. The most important variables for predicting WD were LW_TL, EW_WT and R_D1 in both EW and LW （r2= 0.22）. Selecting the top 10% of the clones by DBH would improve DBH growth by 12.19% （wood density was reduced by 0.14%） and produced similar responses between EW and LW for all tracheid traits： a reduction of 0.94 and 3.69% in tracheid length and increases in tracheid diameters （from 0.36 to 5.24%） and double wall thickness （0.07 and 0.87%）. The two ratios WT/R_D1 and TL/T_D2 across tissues （EW and LW） declined 0.59 and 4.56%, respectively. The decreased tracheid length and the ratio between tracheid length and diameter is disadvantageous for pulp production. The unfavorable relationship of tracheid traits with wood density indicate that multiple trait selection using optimal economic weights and optimal breeding strategies are recommended for the current longterm breeding program for P. tabuliformis.

Modelling spatial variation in the treatment costs of nonpoint source pollution in mountainous regions of southwest China

Non-point source(NPS) pollution is considered to be one of the main threats of the aquatic environment. Mountainous regions are particularly important water sources for urban areas. The various driving factors of NPS pollution such as terrain, precipitation, and vegetation type in mountainous regions show clear spatial heterogeneity. Consequently, the management systems required for NPS pollution in mountainous regions are complex. In this study, we developed a framework to estimate and map the treatment costs for NPS pollution in mountainous regions and applied this method in Baoxing County, a typical mountainous county in Sichuan Province of southwest China. The export levels of total nitrogen(TN) and total phosphorus(TP) in Baoxing County were estimated using the water purification model in InVEST(Itegrated Valuation of Ecosystem Services and Tradeoffs) tool. NPS pollutant treatment costs were calculated based on the level of pollutants exports, water yield, water quality targets, and treatment costs of NPS pollutants per unit mass. The results show that at the watershed level the amounts of TN and TP exported in Baoxing County were below threshold limits. However, at the sub-watershed level, TN and TP excesses of 291.64 and 2.96 tons per year were found, respectively, with mean TN and TP treatment costs of 6.58 US$/hm^2 and 0.35 US$/hm^2. Appraising pollution treatment cost intuitively reflects the overall expenditure in NPS pollution reduction from an economic perspective. This study provides a foundation for the implementation of Payment for Ecosystem Service(PES) and the prevention and control of NPS pollution.

Curvature Compensated CMOS Bandgap Reference with Novel Process Variation Calibration Technique

A lowtemperature coefficient（ TC） bandgap reference（ BGR） with novel process variation calibration technique is proposed in this paper. This proposed calibration technique compensating both TC and output value of BGR achieves fine adjustment step towards the reference voltage,while keeping optimal TC by utilizing large resistance to help layout match. The high-order curvature compensation realized by poly and p-diffusion resistors is introduced into the design to guarantee the temperature characteristic. Implemented in 180 nm technology,the proposed BGR has been simulated to have a power supply rejection ratio（ PSRR） of 91 dB@100 Hz. The calibration technique covers output voltage scope of 0. 49 V-0. 56 Vwith TC of 9. 45 × 10^（-6）/℃-9. 56 × 10^（-6）/℃ over the temperature range of-40 ℃-120 ℃. The designed BGR provides a reference voltage of 500 mV,with measured TC of 10. 1 × 10^（-6）/℃.

Research on the Application of Time Structure Variation Analysis to the Jiashi-Bachu Earthquake Swarm Sequence

In 1997 - 2003, 27 earthquakes with M≥ 5.0 occurred in the Jiashi-Bachu area of Xinjiang. It was a rare strong earthquake swarm activity. The earthquake swarm has three time segments of activity with different magnitudes in the years 1997, 1998 and 2003. In different time segments, the seismic activity showed strengthenin-qguiet changes in various degrees before earthquakes with M ≥ 5.0. In order to delimitate effectively the precursory meaning of the clustering （strengthening） quiet change in sequence and to seek the time criterion for impending prediction, the nonlinear characteristics of seismic activity have been used to analyze the time structure characteristics of the earthquake swarm sequence, and further to forecast the development tendency of earthquake sequences in the future. Using the sequence catalogue recorded by the Kashi Station, and taking the earthquakes with Ms≥ 5.0 in the sequence as the starting point and the next earthquake with Ms = 5.0 as the end, statistical analysis has been performed on the time structure relations of the earthquake sequence in different stages. The main results are as follows： （1） Before the major earthquakes with M ≥ 5.0 in the swarm sequence, the time variation coefficient （δ-value） has abnormal demonstrations to different degrees. （2） Within 10 days after δ= 1, occurrence of earthquakes with M ≥ 5.0 in the swarm is very possible. （3） The time variation coefficient has three types of change. （4） The change process before earthquakes with M5.0 is similar to that before earthquakes with M6.0, with little difference in the threshold value. In the earthquake swarm sequence, it is difficult to delimitate accurately the attribute of the current sequences （foreshock or aftershock sequence） and to judge the magnitude of the follow-up earthquake by δ-value. We can only make the judgment that earthquakes with M5.0 are likely to occur in the sequence. （5） The critical clustering characteristics of the sequence are hierarchical. Only corresponding to a certain magnitude can the sequence have the variation state of critical clustering. （6） The coefficient of the time variation has a clear meaning in physics. After the clustering-quiet state of earthquake activity has appeared, it can describe clearly the randomness of the seismogenic system. Furthermore, it can efficiently clarify whether or not the clustering quiescence variation is of some prognostic meaning. In the case that the earthquake frequency attenuation is essentially normal （h 〉 1 ） and there is no remarkable clustering-quiescence state, it is still possible to discover the abnormal change of the sequence from the time variation coefficient. On the contrary, in the later period of swarm activity, after the appearance of many seismic quiescence phenomena, this coefficient did not appear abnormally, even when h 〈 1, suggesting that the δ-value diagnosis is more universal.

COVID-19疫情期间兰州市大气污染时空变化分析

2020年新冠病毒席卷全球,我国政府采取一系列政策和措施进行防控,减少了污染排放,这个特殊时期为研究人类活动对大气污染的影响提供了良好机会.本文结合了监测站点数据、卫星遥感数据以及气象资料等,从时间和空间上对兰州市疫情期间大气污染物浓度变化进行分析,并利用Pearson相关系数法分析了6种大气污染物(PM_(2.5)、PM_(10)、SO_(2)、NO_(2)、CO、O_(3))之间以及与气象因素(温度、湿度、风速、气压)之间的相关性,同时分析了2021年10月兰州突发疫情下,大气污染物浓度变化,并与2020年作对比.结果表明:(1)2020年疫情防控期间NO_(2)、CO、PM_(2.5)、SO_(2)等的浓度下降明显,其中PM_(2.5)在进入全面抗疫阶段后,下降幅度最大,达到20.5%,NO_(2)、CO次之,大多是在主城区人口密集地区;(2)SO_(2)浓度与历年同期相比,下降幅度最大,达到26.8%,受工业影响较大;(3)CO、NO_(2)、SO_(2)三者具有强相关性,变化趋势保持一致;NO_(2)、SO_(2)浓度变化影响着PM_(2.5)浓度;O_(3)与5种大气污染物均呈负相关,其他5种大气污染物浓度升高时,太阳辐射减少,抑制O_(3)的生成,O_(3)浓度随之下降;(4)气象因素也影响着大气污染物浓度;温度与PM_(2.5)、PM_(10)、SO_(2)、NO_(2)、CO均呈负相关,与O_(3)呈强正相关;湿度与6种大气污染物均呈负相关;风速与PM_(2.5)、PM_(10)、SO_(2)、NO_(2)、CO均呈负相关,与O_(3)呈正相关,但是当风速过高时,也会使O_(3)浓度下降.(5)2021年10月突发疫情防控期间,NO_(2)、CO大幅度下降,PM_(2.5)也受影响,PM_(10)与O_(3)并未有太大变化,而由于工厂并未停工,SO_(2)浓度并未受太大影响.