Effects of cold rolling and heat treatment on microstructure and mechanical properties of AA 5052 aluminum alloy

The microstructures and mechanical properties of homogenized-rolled AA5052 aluminum alloys with different rolling reductions and following annealing treatments were investigated by optical microscope, scanning electron microscope, X-ray diffractometer, micro-hardness and tensile tests. The results show that with increasing rolling reduction, the equiaxed grains are elongated along the rolling direction obviously, and accumulation of rolling reduction increases the work hardening effect, which results in the enhanced strength and degraded plasticity. When rolling reduction is 87%, the ultimate tensile strength reaches 325 MPa but elongation is only 2.5%. There are much more secondary phase precipitates after annealing treatment. With an increase of annealing temperature, the amount of precipitates increases and work hardening diminishes continuously. The elongation is improved to ~23% but the tensile strength is decreased to 212 MPa after annealing at 300 °C for 4 h, which are comparable to those of as-homogenized alloy.

INFLUENCE OF COLD ROLLING REDUCTION ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF TWIP STEEL

The influence of cold rolling reduction on microstructure and mechanical properties of the TWIP （ttwinning induced plasticity） steel was investigated. The results＇ indicated that the steel had better comprehensive mechanical properties when cold rolling reduction was about 65.0% and the annealing temperature was 1000℃. The tensile strength of the steel is about 640MPa and the yield strength is higher than 255MPa, while the elongation is＇ above 82%. The microstructure is composed of austenitic matrix and annealing twins at room temperature, at the same time, a significant amount of annealing twins and stacking faults＇ are observed by transmission electron microscopy （TEM）. Mechanical twins play a dominant role during deformation, and result in exceUent mechanical properties.

Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels

Effects of cold rolling on the microstructure and mechanical properties of Fe-Ni-Mn-Mo-Ti-Cr maraging steels were studied.To investigate the microstructure and mechanical properties,optical microscopy,scanning electron microscopy,X-ray diffraction,tensile test,and hardness test were used.The results show that the solution-annealing treatment in the cold-rolled steel redounds to the formation of sub-microcrystalline Fe2（Mo,Ti） Laves phase particles,which are stable at high temperatures.These secondary Laves phase particles prevent from recrystallization at high temperatures and correspond to semi-brittle fracture in the subsequent aging treatment.

Microstructure and textural evolution during cold rolling and annealing of commercially pure titanium sheet

The effects of cold rolling and annealing on the microstructure and textural evolution of a commercially pure titanium（CP-Ti） sheet were investigated. Electron backscatter diffractometry demonstrates that the deformation during rolling is accommodated by twinning and slip. Additionally, twinning is the dominant deformation mechanism when the cold rolling reduction is less than 40%. During rolling, {11ˉ22}11ˉ2ˉ3contraction twinning（CT） and {10ˉ12}10ˉ11 extension twinning（ET） are activated. And, the intensity of the（0002） pole along the ND gradually increases with increasing deformation. During annealing, the fraction of low angle grain boundaries（LAGBs） and the intensity of the（0002） pole along the ND gradually decrease slightly with increasing annealing time, while twinning lamellae disappear rapidly. When the annealing time reaches 60 min, 20% cold-rolled sheet recrystallizes almost completely.

Microstructures of ultra-fine grained FeCoV alloys processed by ECAP plus cold rolling and their evolutions during tempering

A new processing method,equal channel angular pressing(ECAP)plus cold rolling(CR),was applied to producing ultra-fine grained FeCoV alloy.The microstructures of ultra-fine grained FeCoV alloy after ECAP,ECAP plus CR,and the effect of tempering treatment on the microstructure of FeCoV alloy produced by ECAP plus CR were investigated.The results show that an elongated substructure with a width of about 0.3μm is obtained after four-pass ECAP using Route A.Cold rolling after ECAP cannot change the morphologies of elongated substructure,and it results in higher fraction of high-angle boundaries and higher dislocation density compared with the identical ECAP without rolling.Subsequent tempering for 30 min at 853 K brings about many nano-phases precipitating at subgrain boundaries and insides the grains,and the size of precipitated phase is measured to be about 10 nm.Nano-phases grow up with increasing tempering temperature and equiaxed structure forms at 883 K.

Microstructure, cold rolling, heat treatment, and mechanical properties of Mg-Li alloys

The magnesium-lithium （Mg-Li） alloy exhibits two phase structures between 5.7wt% and 10.3wt% Li contents, consisting of the a （hcp） Mg-rich and the β （bcc） Li-rich phases, at room temperature. In the experiment, Mg-5Li-2Zn, Mg-9Li-2Zn, Mg-16Li-2Zn, Mg-22Li-2Zn, Mg-5Li-2Zn-2Ca, Mg-9Li-2Zn-2Ca, Mg-16Li-2Zn-2Ca, and Mg-22Li-2Zn-2Ca （wt%） were melted. During the melting process, the flux, which was composed of lithium chloride （LiCl） and lithium fluoride （LiF） in the proportion of 3：1 （mass ratio） and argon gas were used to protect the alloys from oxidation. The microstructure, mechanical properties, and cold-rolling workability of the wrought alloys were studied. The crystal grain of the alloys （adding Ga） is fine . The hardness of the studied alloys decreases with an increase in element Li. The density of the studied alloys is in the range of 1.187 to 1.617 g/cm^3. The reduction of the Mg-16Li-2Zn and Mg-22Li-2Zn alloys can exceed 85% at room temperature. The Mg-9Li-2Zn-2Ca alloy was heat treated at 300℃ for 8, 12, 16, and 24 h, respectively. The optimum heat treatment of the Mg-9Li-2Zn-2Ca alloy is 300℃×12h by metallographic observation and by studying the mechanical properties of the alloys.

MICROSTRUCTURE EVOLUTION AND MECHANICAL HARDENING OF HYPEREUTECTOID PEARLITIC STEEL DURING COLD ROLLING

The microstructure evolution of different cold rolling reductions （from 0 to 81.6%） was studied by SEM （scanning electron microscopy） and TEM （transmission electron microscope）. The study showed that the orientation multiplicity of pearlitic lamellas resulted in inhomogeneous deformation of different pearlitic lamellas, and with the increase of reduction, the microstructure underwent a course of ＂homogeneity → inhomogeneity → homogeneity＂. The result of XRD （X-ray diffraction） analysis indicated that cementite did not decompose and dissolve into ferrite; the results of the mechanical property test suggested that the relationship between Rp0.2 （yield strength） and ε （true strain） was in good agreement with Hollomon relationship. With the equation Rp0.2 = 1465ε^0.18, the yield strength of the steel in different reductions could be well predicted.

Microstructure and texture evolution in commercial-purity Zr 702 during cold rolling and annealing

Microstructure and texture evolution in commercial-purity Zr 702 during cold rolling and annealing was investigated by optical microscopy, transmission electron microscopy, and X-ray diffraction. The results showed that crystallographic slip was the predominant deformation mechanism in the early stage of deformation. Deformation twins started to form when the rolling reduction was larger than 38.9%; both the dislocation density and the number of twins increased with increasing rolling reduction. The initial texture of the Zr 702 plate consisted of the basal fiber component. During cold rolling the strength of the basal fiber first decreased and then increased with increasing rolling reduction. The cold-rolled sheets were fully recrystallized after being annealed at 550℃. The recrystallization temperature and the size of recrystallized grains decreased with increasing rolling reduction. A larger rolling reduction resulted in a higher grain growth rate when the annealing temperature increased from 550℃ to 700℃. The recrystallization texture was characterized by a major basal fiber and a minor {0113}〈2110〉 component. The strength of the recrystallization texture increased with increasing rolling reduction.

Effects of cold and warm cross-rolling on microstructure and texture evolution of AZ31B magnesium alloy sheet

Mg alloys conventionally rolled often present strong basal textures that affect negatively further deformations,limiting their applications.The present research found that cross-rolling experiences in adequate conditions can weaken those intense basal textures as a result of the interaction of deformation mechanisms and dynamic recrystallization.The effects of rolling temperature and strain rate on the microstructure and texture of an AZ31B magnesium alloy sheet generated heterogeneous microstructure where the initial basal texture was strengthened during cold cross-rolling and it was gradually weakening by the rolling reduction and the rolling temperature increases in such a way that a rather weak basal fiber was produced applying reductions higher than 15%at temperatures higher than 200℃.Their ODF functions supported the texture weakening,exhibiting a combination of two crystallographic orientations represented by{0001}<211^(-)0>and{0001}<101^(-)0>.

Effect of annealing cooling rate on microstructure and mechanical property of 100Cr6 steel ring manufactured by cold ring rolling process

Pre-heat treatment is a vital step before cold ring rolling and it has significant effect on the microstructure and mechanical properties of rolled rings.The 100Cr6 steel rings were subjected to pre-heat treatment and subsequent cold rolling process.Scanning electron microscopy and tensile tests were applied to investigate microstructure characteristic and mechanical property variations of 100Cr6 steel rings undergoing different pre-heat treatings.The results indicate that the average diameter of carbide particles,the tensile strength and hardness increase,while the elongation decreases with the decrease of cooling rate.The cooling rate has minor effect on the yield strength of sample.After cold ring rolling,the ferrite matrix shows a clear direction along the rolling direction.The distribution of cementite is more homogeneous and the cementite particles are finer.Meanwhile,the hardness of the rolled ring is higher than that before rolling.

Microstructure evolution and mechanical properties of Cu-0.36Be-0.46Co alloy fabricated by heating-cooling combined mold horizontal continuous casting during cold rolling

Cu-0.36 wt.%Be-0.46 wt.%Co alloy plate with 300 mm in width and 10 mm in thickness prepared by heating-cooling combined mold(HCCM) horizontal continuous casting was cold rolled. Microstructure evolution and mechanical properties of the alloy as well as its deformation mechanism were investigated. The results showed that the as-cast alloy plate had columnar grains along the length direction, good surface quality and elongation of 35%, which was directly large-reduction cold rolled without surface treatment, and the accumulative cold rolling reduction reached 98%. When the reduction was small(20%), numerous dislocations and dislocation cells formed, and the deformation mechanism was dislocation slip. When the reduction was 40%, deformation twins appeared, and interactions between twins and dislocation cells induced strip-like dislocation cells. When the reduction exceeded 60%, shear bands formed and apparent crystal rotation in the micro-region happened. Further increasing the reduction, the amount of the shear bands rose and they interacted with each other, which refined the grains apparently. The tensile strength and hardness increased from 353 MPa and HV 119 of the as-cast alloy to 625 MPa and HV 208 with 95% reduction, respectively, and the elongation reduced from 35% to 7.6%. A process of HCCM horizontal continuous casting-cold rolling can work as a novel compact method to fabricate Cu-Be alloy sheet.

Effect of annealing temperature on microstructure and mechanical properties of Mg-Zn-Zr-Nd alloy with large final rolling deformation

In this study,the Mg-3Zn-0.5Zr-χNd(χ=0,0.6)alloys were subjected to final rolling treatment with large deformation of 50%.The impact of annealing temperatures on the microstructure and mechanical properties was investigated.The rolled Mg-3Zn-0.5Zr-0.6Nd alloy exhibited an ultimate tensile strength of 386 MPa,a yield strength of 361 MPa,and an elongation of 7.1%.Annealing at different temperatures resulted in reduced strength and obviously increased elongation for both alloys.Optimal mechanical properties for the Mg-3Zn-0.5Zr-0.6Nd alloy were achieved after annealing at 200℃,with an ultimate tensile strength of 287 MPa,a yield strength of 235 MPa,and an elongation of 26.1%.The numerous deformed microstructures,twins,and precipitated phases in the rolled alloy could impede the deformation at room temperature and increase the work hardening rate.After annealing,a decrease in the work hardening effect and an increase in the dynamic recovery effect were obtained due to the formation of fine equiaxed grains,and the increased volume fraction of precipitated phases,which significantly improved the elongation of the alloy.Additionally,the addition of Nd element could enhance the annealing recrystallization rate,reduce the Schmid factor difference between basal and prismatic slip systems,facilitate multi-system slip initiation and improve the alloy plasticity.

Multilayered Ti-Al intermetallic sheets fabricated by cold rolling and annealing of titanium and aluminum foils

Multilayered Ti-Al based intermetallic sheets were fabricated by sintering alternately layered titanium and aluminum foils.The microstructure and phase formation of the obtained sheets under different sintering conditions were evaluated by various techniques.The results reveal that when the sintering temperature is above the melting point of aluminum,the self-propagating high-temperature synthesis reaction occurs between Ti and Al,and forms various phases of Ti-based solid solutions including α-Ti Ti3Al,TiAl,TiAl2 and α-Ti including TiAl3,etc.When the sintering time increased,Ti-based solid solution,TiAl2 and TiAl3 disappeared gradually,and the sheet containing Ti3Al and TiAl phases in a multilayered structure formed finally.A lot of voids were also observed in the sintered structures,which were caused by the melting Al,Kirkendall effect and the difference of molar volumes between reactants and products.The voids were eliminated and a dense sample was obtained by the following hot press.

Bonding enhancement of cold rolling TA1 P-Ti/AA6061 composite plates via surface oxidation treatment

TA1 P-Ti/AA6061 composite plate was produced by oxidizing the surface of the titanium plate and adopting a cold roll bonding process.The results revealed that the oxide film(Ti6O)prepared on the surface of TA1 pure titanium was easy to crack during the cold roll bonding,thereby promoting the formation of an effective mechanical interlock at the interface,which can effectively reduce the minimum reduction rate of the composite plates produced by cold rolling of titanium and aluminium plates.Moreover,the composite plate subjected to oxidation treatment exhibited high shear strength,particularly at a 43%reduction rate,achieving a commendable value of 117 MPa.Based on oxidation treatment and different reduction rates,the annealed composite plates at temperatures of 400,450,and 500°C displayed favorable resistance to interface delamination,highlighting their remarkable strength-plasticity compatibility as evidenced by a maximum elongation of 31.845%.

Effects of stress state on texture and microstructure in cold drawing-bulging of CP-Ti sheet

Three different stress states of the combination of tensile（t） stress and compressive（c） stress,t t,t c and t c c,exist in the deformed commercially pure titanium（CP-Ti） sheet during cold drawing-bulging.The textures and microstructures in the different stress state regions were investigated by means of XRD and TEM analysis.Similar development of texture and microstructure is achieved with less thickness strain under multiaxial stresses in drawing-bulging than in cold rolling.The results show that texture and microstructure are much sensitive to multiaxial stresses.Twinning is more easily activated under compressive stress than tensile stress.Prism a slip is heavily affected by tensile stress,resulting in a remarkable change of the intensity of（0°,35°,0°） texture,while pyramidal c＋a slip,forming（20°,35°,30°） texture,weakens with the increase of thickness strain in spite of stress state.

Strength enhancement of Mg-3Gd-1Zn alloy by cold rolling

The severe cold rolling was employed to enhance strength of Mg-3Gd-lZn （mass fraction, %） alloy sheet. The 0.2% yield stress of the Mg-3Gd-1Zn hot-rolled sheet can be increased by 150% through the single-pass cold rolling with the reduction of 23%, due to the high intensity of dislocation and basal texture established during cold rolling. Compared with the Mg-3Gd-lZn hot-rolled sheet, the cold-rolled sheet annealed at 350 for 30 min may get an enhancement in strength without a great loss of ductility. The sheet processed by multi-pass cold rolling does not show a higher strength as expected, due to the softening effect of shear bands. However, the thin slab with the thickness less than 1 mm can be produced by the multi-pass cold rolling with the annealing treatment as few as possible.

Mechanical performance and texture characteristic of an IF steel containing Nb and Ti by double cold rolling

Single cold rolling and double cold rolling were applied to hot rolled strips with different reduction ratios. The evolutions of { 100}, { 111} and Goss face texture during double rolling were investigated by comparing the orientation distribution function （ODF） of the double rolled sample with that of the single rolled one. The double cold rolling texture is characterized by a higher γ-texture and a lower α-texture, and the { 111}〈112〉 component is improved remarkably. Based on the TEM observation and mechanical properties test, it is found that the reduction ratio assignment significantly affects the texture variation, as-annealing microstructures, and properties of the double cold rolled samples. These results may provide a theoretical guide for the industrial production of double cold rolled IF steel.

Enhanced tensile properties of a reversion annealed 6.5Mn-TRIP alloy via tailoring initial microstructure and cold rolling reduction

The feasibility of improving the overall performance of medium Mn steels was demonstrated via tailoring the initial microstructure and cold rolling reduction. The combined effects of cooling patterns after hot rolling （HR） and cold rolling （CR） reductions show： （1） as the cooling pattern varied from furnace cooling （FC） to oil quenching （OQ）, the intercritically annealed microstructure was dramatically refined and the fraction of recrystallized ferrite dropped, regardless of CR reductions. This resulted in both high yield/ultimate tensile strengths （YS/UTS） but low total elongation to fracture （El）; （2） as the CR reduction increased from 50% to 75%, the OQ-samples after annealing exhibited a more refined microstructure with relatively higher fractions of retained austenite and sub-structure, leading to higher YS and UTS but lower El; whereas the FC samples appeared to exhibit little difference in overall tensile properties in both cases. The differences in microstructural evolution with cooling patterns and CR reductions were explained by the calculated accumulated effective strain （eAES）, which was considered to be related to degrees of recovery and recrystallization of the deformed martensite （α＇）. The optimal tensile properties of -1 GPa YS and -40 GPa.% UTSxEI were achieved in the OQ-50%CR annealed samples at 650 ℃ for 1 h. This was quite beneficial to large-scale production of ultra-high strength steels, owing to its serious springback during heaw cold working.

Effects of rolling and annealing on microstructures and properties of Cu-Mg-Te-Y alloy

Microstructures and element distributions of the as-cast, hot-rolled and cold-rolled Cu-Mg-Te-Y alloys were studied. Effects of rolling process and annealing temperature on the properties of the Cu-Mg-Te-Y alloys were correspondingly investigated. The results indicate that the Mg element is homogeneously distributed in the matrix and the fragmentized Cu2Te phase is dispersed in the matrix after hot rolling. Then, the Cu2Te phase is further stretched to strip shape after the cold rolling process. The microstructures of the cold-rolled alloy keep unchanged for the sample annealed below 390 ℃ for 1 h. However, after annealing at 550 ℃ for 1 h, the copper alloy with fibrous microstructures formed during the cold rolling process recrystallizes, leading to an obvious drop of hardening effect and an increase of electrical conductivity. The Cu-Mg-Te-Y alloy with better comprehensive properties is obtained by annealing at 360-390 ℃.

MECHANICS ANALYSIS ON PRECISE FORMING PROCESS OF EXTERNAL SPLINE COLD ROLLING

According to the suitable assumption, the deformation process of external spline cold rolling is analyzed. By the graphing method, the slip-line field of plastically deforming area in process of external spline cold rolling is set up. Different friction-conditions are used in different contact areas in order to realistically reflect the actual situation. The unit average pressure on contact surface of the rolling process is solved according to the stress filed theory of slip-line. And the formulae of the rolling-force and rolling-moment are established. The theoretical result is well consistent with the finite element analysis. A theoretical basis is provided for the precise forming process of spline cold rolling and the production of external splined shafts.