PROFILE AND FLATNESS CONTROL SYSTEM IN 1700mm HOT STRIP MILLS OF ANSTEEL

Varying contact-length backup roll and linearly variable crown work roll are provided for improving the mill performance of profile and flatness control. Integrated with theses technologies, relevant profile and flatness control models are developed for hot strip mills on the basis of large amount of finite element calculation. These models include shape setup control model in process control system, bending force feedforward control model, crown feedback control model and flatness feedback control model in basis automation system. Such a profile and flatness control system with full functions is applied in 1 700 mm industrial hot strip mills of Ansteel. Large amount of production data shows that the crown precision with the tolerance of±18 μm is over 90%, the strip percentage which the actual flatness is within ±25 I-unit surpasses 96%, and general roll consume is reduced by 28% by using the profile and fiatness control system. In addition, schedule-free rolling is realized.

VCR and ASR technology for profile and flatness control in hot strip mills

The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and analyzed by the developed finite element models of different typical roll contours configurations.A rather smooth local work roll contour near strip edges and an increase in rolled length can be obtained by application of long stroke work roll shifting system with conventional work roll contours that is incapable of the crown control.In comparison with the conventional backup and work roll contours configuration,the crown control range by the roll bending force enhances by 12.79% and the roll gap stiffness increases by 25.26% with the developed asymmetry self-compensating work rolls(ASR) and varying contact backup rolls(VCR).A better strip profile and flatness quality,an increase in coil numbers within the rolling campaign and a significant alleviated effect of severe work roll wear contours on performance of edge drop control are achieved by the application of ASR with crown control and wear control ability in downstream stand F5 and VCR in all stands of 1 700 mm hot strip mill.

Gene expression profile in rat small intestinal allografts after cold preservation/reperfusion

AIM: To determine the changes of gene expression profile in small intestinal allografts in rats after cold preservation/ reperfusion, and to identify the genes relevant to cold preservation/reperfusion injury. METHODS: Heterotopic segmental small bowel transplantation was performed in six rats with a sham operation and they were used as controls. Total RNA was extracted from the allografts (experimental group) and normal intestines (control group) 1 h after cold preservation/ reperfusion, and then purified to mRNA, which was then reversely transcribed to cDNA, and labeled with fluorescent Cy5-dUTP and Cy3-dUTP to prepare hybridization probes. The mixed probes were hybridized to the cDNA microarray. After high-stringent washing, the fluorescent signals on cDNA microarray chip were scanned and analyzed. RESULTS: Among the 4 096 target genes, 82 differentially expressed genes were identified between the two groups. There were 18 novel genes, 33 expression sequence tags, and 31 previously reported genes. The selected genes may be divided into four classes: genes modulating cellular adhesion, genes regulating cellular energy, glucose and protein metabolism, early response genes and other genes. CONCLUSION: A total of 82 genes that may be relevant to cold preservation/reperfusion injury in small intestinal allografts are identified. Abnormal adhesion between polymorphonuclears and endothelia and failure in energy, glucose and protein metabolism of the grafts may contribute to preservation/reperfusion injury. The functions of the novel genes identified in our study need to be clarified further.

X-ray peak profile analysis of dislocation type,density and crystallite size distribution in cold deformed Pb-Ca-Sn alloys

The density,nature of the dislocations and distribution of the domain sizes in cold-deformed Pb-Ca-Sn solid solution were determined by X-ray diffraction profile analysis.The dislocation densities are of the order of 1010 cm-2.The strain broadening of diffraction profiles was accounted for by dislocation contrast factor.The coherent domain size was determined by the recently developed PM2K software package.Assuming that the domain size distribution is log-normal,the distribution function（median μ and variance σ） was calculated from the size parameters determined from X-ray diffraction profile analysis.

Determination of Optimal Work Roll Profile for Cold Strip Mill

The model of predicting distribution of strip thickness at the exit and tension stress is established by using weighted residual method and variational method with consideration of rolled metal lateral flow.A New method of calculating loaded roll gap in relation to target tension stress is proposed.The minimum square summation of loaded roll gap deviation is used as an objective function for the first time to optimize initial work roll profile.

The analysis and control methods of profile irregular on 1580 mm hot rolling mill

The profile quality of hot strip will affect the quality of cold strip,therefore,it is one of key quality fields which needs improve.In this paper,three kinds of profile irregular defects of hot rolling strip were discussed based on the production experience.Through profile,rolling,work-roll's wear and simulation methods,this paper discovered the reasons of these quality defects.Meanwhile,the ways to deal with these defects were presented and have been proved effectively.Decrease the number of narrow strips,select the suitable type of spray,set the better angle of nozzle can improve the profile quality of hot strip.

Thermal profile of work roll during strip hot rolling

The thermal expansion of work rolls during hot strip rolling was modeled by a two-dimensional difference method. The calculation model was validated by comparison between the predictions to the measured results. With that model ,the effects of rolling process parameters such as the rolling plan, mill pacing ,coolant flow rate and stepped cooling on the roll thermal profile were investigated. The result shows that stepped cooling of work rolls can be used to control complicated flatness defects such as quarter buckles during hot strip rolling.

Cold exposure alters proteomic profiles of the hypothalamus and pituitary in female rats

Objective:Studies have shown that both short-term and long-term cold exposures disturb the biological process.The aim of the present study is to investigate the effects of intermittent cold exposure on proteomic profiles in the hypothalamus and pituitary of female Sprague-Dawley(SD)rats.Materials and methods:The rats were exposed to-10°C in a cabin for 4 h per day,and the treatment lasted for 14 days.The comparative label-free LC-MS/MS analysis was performed to investigate the changes of proteomic profiles in the hypothalamus and pituitary.ELISA analysis was used to validate the expression of differential proteins.Results:22 differential proteins in the hypothalamus and 75 differential proteins in the pituitary were identified by the label-free proteomic analysis.Gene ontology annotation and enrichment analysis indicated that cold exposure disrupted protein phosphorylation,filopodium assembly,intracellular protein transport,peripheral nervous system neuron axonogenesis,spinal cord development,Golgi organization,positive regulation of pseudopodium assembly,and cell-cell adhesion.Three proteins(Cdc42,Ptprs,and Setd7)were down-regulated in the cold exposure group.Conclusion:The results indicate that intermittent cold exposure alters the proteomic profiles of hypothalamus and pituitary in female rats.

Microstructural evolution during hot and cold deformation of Ti-36Nb-2Ta-3Zr-0.35O alloy

The Ti-36Nb-2Ta-3Zr-0.350 （mass fraction, %） （TNTZO） alloy was produced by cold isostatic pressing and sintering from elemental powders, followed by hot and cold deformation. The effects of deformation process on microstructures and mechanical properties were investigated using the SEM, TEM, OM and the universal material testing machine. Results show that the alloy can be easily hot forged and cold swaged due to the fine-grained microstructure. Only after cold swaging by 85%, the alloy shows the typical ＂marble-like＂ structure. And thecold deformation is accompanied by stress-induced a＂ phase transformations. Moreover, both the strength and the ductility of the alloy are significantly improved by hot and cold working.

Removal of diminutive colorectal polyps: A prospective randomized clinical trial between cold snare polypectomy and hot forceps biopsy

AIMTo compare the efficacy and safety of cold snare polypectomy (CSP) and hot forceps biopsy (HFB) for diminutive colorectal polyps.METHODSThis prospective, randomized single-center clinical trial included consecutive patients ≥ 20 years of age with diminutive colorectal polyps 3-5 mm from December 2014 to October 2015. The primary outcome measures were en-bloc resection (endoscopic evaluation) and complete resection rates (pathological evaluation). The secondary outcome measures were the immediate bleeding or immediate perforation rate after polypectomy, delayed bleeding or delayed perforation rate after polypectomy, use of clipping for bleeding or perforation, and polyp retrieval rate. Prophylactic clipping after polyp removal wasn’t routinely performed.RESULTSTwo hundred eight patients were randomized into the CSP (102), HFB (106) and 283 polyps were evaluated (CSP: 148, HFB: 135). The en-bloc resection rate was significantly higher with CSP than with HFB [99.3% (147/148) vs 80.0% (108/135), P < 0.0001]. The complete resection rate was significantly higher with CSP than with HFB [80.4% (119/148) vs 47.4% (64/135), P < 0.0001]. The immediate bleeding rate was similar between the groups [8.6% (13/148) vs 8.1% (11/135), P = 1.000], and endoscopic hemostasis with hemoclips was successful in all cases. No cases of perforation or delayed bleeding occurred. The rate of severe tissue injury to the pathological specimen was higher HFB than CSP [52.6% (71/135) vs 1.3% (2/148), P < 0.0001]. Polyp retrieval failure was encountered CSP (7), HFB (2).CONCLUSIONCSP is more effective than HFB for resecting diminutive polyps. Further long-term follow-up study is required.

Efficacy and adverse events of cold vs hot polypectomy: A meta-analysis

AIM: To compare previously reported randomized controlled studies (RCTs) of cold and hot polypectomy, we systematically reviewed and clarify the utility of cold polypectomy over hot with respect to efficacy and adverse events.METHODS: A meta-analysis was conducted to evaluate the predominance of cold and hot polypectomy for removing colon polyps. Published articles and abstracts from worldwide conferences were searched using the keywords “cold polypectomy”. RCTs that compared either or both the effects or adverse events of cold polypectomy with those of hot polypectomy were collected. The patients’ demographics, endoscopic procedures, No. of examined lesions, lesion size, macroscopic and histologic findings, rates of incomplete resection, bleeding amount, perforation, and length of procedure were extracted from each study. A forest plot analysis was used to verify the relative strength of the effects and adverse events of each procedure. A funnel plot was generated to assess the possibility of publication bias.RESULTS: Ultimately, six RCTs were selected. No significant differences were noted in the average lesion size (less than 10 mm) between the cold and hot polypectomy groups in each study. Further, the rates of complete resection and adverse events, including delayed bleeding, did not differ markedly between cold and hot polypectomy. The average procedural time in the cold polypectomy group was significantly shorter than in the hot polypectomy group.CONCLUSION: Cold polypectomy is a time-saving procedure for removing small polyps with markedly similar curability and safety to hot polypectomy.

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

To get a full understanding of hot extrusion,solid solution treatment and aging process on the Al−0.56Mg−0.63Si alloy,the microstructure and mechanical properties of a U-shaped profile were studied through optical microscopy,scanning electrical microscopy,transmission electrical microscopy,hardness,and tensile tests.The coarse equiaxed grains existed near the profile edge as a result of the dynamic recrystallization nucleation and exceeding growth during hot extrusion.The fibrous deformed and sub-structured grains located between the two coarse grain layers,due to the occurrence of work-hardening and dynamic recovery.Perpendicular needle β′′precipitates were distributed inside the grain,and obvious precipitates-free zone appeared after aging treatment.The tensile strength,yield strength and elongation of the aged Al−Mg−Si alloy U-shaped profile were no less than 279.4 MPa,258.6 MPa,and 21.6%,respectively.The fracture morphology showed dimple rupture characteristics.The precipitates and grain boundaries played key role in the strengthening contribution.

Comment on 'Efficacy and adverse events of cold vs hot polypectomy: A meta-analysis'

This is a comment on a meta-analysis of published studies comparing cold vs hot polypectomy. We believe that the conclusion of this meta-analysis that "cold polypectomy is a time-saving procedure for removing small polyps with markedly similar curability and safety to hot polypectomy" needs more rigorous evidence.

Chemical Properties of Pectin from Industry Hot and Cold Break Tomato Products

Tomato processing includes a break step, which involves rapid heating of freshly chopped tomatoes to >90°C for hot break, or 60°C to 77°C for cold break. Pectolytic enzyme deactivation is believed to be the key element in the hot break step;therefore, pectin content of different products should be qualitatively distinct. The objective of this study was to investigate the effect of hot break versus cold break on the cell-wall pectin of tomato. Cell-wall pectin from hot and cold break tomato products was isolated and analyzed for carbohydrate composition, degree of polymerization, and degree of esterification. The results showed no observable differences in the cell-wall pectin isolated from the two products, indicating that there was no significant pectolytic breakdown of the tomato in the cold break product, and the pectin might not, by itself, contribute to the differences in the final product viscosity resulting from the two processing techniques.

Experimental research and application of cold cutting to hot stamping parts based on multiphase microstructure

Among the bottlenecks that hinder the improvement of the production efficiency of hot stamping are high strength and difficulty in edge cutting and hole punching.Starting from the preparation of hot stamping multiphase microstructure materials,this paper developed a plate quenching die system with controllable surface temperature and prepared four types of hot stamping plates with different martensite volume fractions.Then,straight edge cold cutting experiments were performed to study the influence of cutting clearance and cutting force on fracture quality.The results show that the bright zone is the largest when the cutting clearance is 0.14 mm,and the cutting experience coefficient of the hot stamping sheet with each martensite volume fraction is obtained when the cutting clearance is 0.14 mm.The research results of this paper were applied to the production of hot stamping parts.

A UML profile for framework modeling

The current standard Unified Modeling Language(UML) could not model framework flexibility and extendibility adequately due to lack of appropriate constructs to distinguish framework hot-spots from kernel elements. A new UML profile that may customize UML for framework modeling was presented using the extension mechanisms of UML, providing a group of UML extensions to meet the needs of framework modeling. In this profile, the extended class diagrams and sequence diagrams were defined to straightforwardly identify the hot-spots and describe their instantiation restrictions. A transformation model based on design patterns was also put forward, such that the profile based framework design diagrams could be automatically mapped to the corresponding implementation diagrams. It was proved that the presented profile makes framework modeling more straightforwardly and therefore easier to understand and instantiate.

Internal oxidation of hot-rolled ultra-high strength steel and its effect on the surface quality of cold-rolled sheets

In this study,the scale and internal oxidation of hot-rolled ultra-high strength steel sheets were characterized.It was found that both the formation of the scale and the internal oxidation of Si and Mn depended on the coiling temperature and position of the steel sample on the strip coil.At a relatively high coiling temperature,a large amount of internal oxidation was observed on the samples cut from the middle of the coil.The depth of the internal oxidation zone exceeded 10 μm and a thin iron layer covering the scale was observed in some cases.Pickling and cold-rolling experiments were conducted on selected samples.Scale pickling was found to be greatly delayed by the formation of an iron layer,which frequently resulted in under-pickled defects.In addition,pickling of the entire internal oxidation zone was difficult,except at the grain boundaries,where the degree of internal Si and Mn oxidation was enriched.The surface of the cold-rolled steel sheet was ruined by the remaining oxidation zone in the subsurface of the pickled steel.The internal oxidation of hot-rolled ultra-high strength steel must be precisely controlled to improve the subsequent surface quality of cold-rolled steel.

Profile distribution and seasonal dynamics of water-extractable carbohydrate in soils under mixed broad-leaved Korean pine forest on Changbai Mountain

Carbohydrate represents an important part of the soil labile organic carbon pool. Water soluble carbohydrate drives the C cycle in forest soil by affecting microbial activity and hot water extractable car- bohydrate is thought related to soil carbon sequestration due to the asso- ciation with soil aggregation. In a temperate forest region of northeast China, Changbai Mountain, we investigated the abundance, spatial dis- tribution, and seasonal dynamics of cool and hot-water extractable car- bohydrate in soils under mixed broad-leaved Korean pine forest. The concentrations of cool-water extractable carbohydrate （CWECH） in three soil layers （0-5, 5-10, 10-20 cm） ranged from 4.1 to 193.3 g.kg-1 dry soil, decreasing rapidly with soil depth. On an annual average, the CWECH concentrations in soils at depths of 5-10 and 10-20 cm were 54.2% and 24.0%, respectively, of that in the 0-5 cm soil layer. CWECH showed distinct seasonal dynamics with the highest concentrations in early spring, lowest in summer, and increasing concentrations in autumn. Hot-water extractable carbohydrate （HWECH） concentrations in three soil layers ranged from 121.4 to 2026.2 g.kgq dry soil, which were about one order of magnitude higher than CWECH. The abundance of HWECH was even more profile-dependent than CWECH, and decreased more rapidly with soil depth. On an annual average, the HWECH concentration in soils 10-20 cm deep was about one order of magnitude lower than that in the top 0-5 cm soil. The seasonality of HWECH roughly tracked that of CWECH but with seasonal fluctuations of smaller amplitude. The car- bohydrate concentrations in cool/hot water extracts of soil were positively correlated with UV254 and UV2s0 of the same solution, which has implications for predicting the leaching loss of water soluble organic carbon.

Ventilated Double Skin Facades in Hot-Summer and Cold-Winter Zones in China

Double-skin facades(DSF)are a technique developed for colder climates,so few people think about whether or not it can also be used for hot-summer and cold-winter zones in China.After analyzing the problems of using DSF for hot-summer zones,this paper explored on the possibility of applying DSF in hot-summer and cold-winter zones in China.The main existing research methods for DSF were also collected and commented.If properly managed,the ventilated DSF with controlled shading devices can be used even in hot summer in China.

THE COLD AND HOT DAMAGES TO THE CITRUS IN THE THREE GORGES AREA OF THE CHANGJIANG RIVER

Starting from the research on and collection of the damaging factors andindex of the cold and hot damages to citrus, this peper systematically studies the apparent properties in temporal and spatial distribution, differences, relationship of the twokinds of disasters and their impact on citrus production in the Three Gorges area inHubei. It also reveals the important faCt that it is warmer in winter and hotter in springsince the 1980s, which is the cause of departing to two poles of the cold and hot damages, and discusses the alleviating effect to the disasters by the Three Gorges Project.Finally some countermeasures are proposed.