It was shown by the study of TEM that the fine lamellar pearlite becomes a ductile phase dur- ing cold drawing.There exist many ledges to emit dislocations at Fe_3C/Fe interface.It is one of the reasons that high dens...It was shown by the study of TEM that the fine lamellar pearlite becomes a ductile phase dur- ing cold drawing.There exist many ledges to emit dislocations at Fe_3C/Fe interface.It is one of the reasons that high density of dislocations emerges at the Fe_3C/Fe interface. Furthermore,there are some evidences to support that dislocation cuts through Fe_3C.There- fore,it is necessary to consider the contribution of cementite being sheared strengthening.展开更多
The paper presents the results of investigation on the effect of soaking time on the yield strength, ductility and hardness properties of annealed cold-drawn low carbon steel. The low carbon steel cold-drawn at 40% de...The paper presents the results of investigation on the effect of soaking time on the yield strength, ductility and hardness properties of annealed cold-drawn low carbon steel. The low carbon steel cold-drawn at 40% deformation was annealed at 900 deg Celsius for soaking times of 10, 20, 30, 40, 50 and 60 minutes. Tensile, charpy and Brinnel hardness tests were conducted to determine the yield strengths, tensile strengths, impact strengths, ductility and hardness of the annealed steel with increasing soaking time. The yield strength, tensile strength, hardness and impact strength of the steel showed a continuous drop in value with increasing soaking time up to 60 minutes with a steep drop between 30 and 40 minutes. Ductility values followed the same decreasing trend up to 40 minutes soaking time after which the values started increasing again till 60 minutes soaking time. There was a linear relationship between the tensile strength and hardness of the material for different soaking times. This linear relationship was also observed for yield strength and hardness of the material.展开更多
The evolution of microstructure and texture for drawn polycrystalline Ag was investigated by transmission electron microscopy and electron backscattering diffraction.The results show that there are deformation twins a...The evolution of microstructure and texture for drawn polycrystalline Ag was investigated by transmission electron microscopy and electron backscattering diffraction.The results show that there are deformation twins and some un-tangled discrete dislocations at low strains.When the strain is increased to 0.58,a lot of high density dislocation walls and microbands come into being.At the same time,some twins lose the twinning relationship of 60°<111>.At a strain of 0.94,both dislocation boundaries and twin boundaries will rotate to the axis direction of wires and the shear bands start to appear.When the strain is higher than 1.96,most of the boundaries are parallel to the drawn direction.Texture analysis indicates that with the strain increasing,the volume fraction of complex texture component decreases,but<111>and<100>texture components increase.However,the variation in the volume fraction of each texture component as strains is not evident when the strains are higher than 0.58.For polycrystalline Ag with low stacking fault energy,complex texture components are easily formed.展开更多
文摘It was shown by the study of TEM that the fine lamellar pearlite becomes a ductile phase dur- ing cold drawing.There exist many ledges to emit dislocations at Fe_3C/Fe interface.It is one of the reasons that high density of dislocations emerges at the Fe_3C/Fe interface. Furthermore,there are some evidences to support that dislocation cuts through Fe_3C.There- fore,it is necessary to consider the contribution of cementite being sheared strengthening.
文摘The paper presents the results of investigation on the effect of soaking time on the yield strength, ductility and hardness properties of annealed cold-drawn low carbon steel. The low carbon steel cold-drawn at 40% deformation was annealed at 900 deg Celsius for soaking times of 10, 20, 30, 40, 50 and 60 minutes. Tensile, charpy and Brinnel hardness tests were conducted to determine the yield strengths, tensile strengths, impact strengths, ductility and hardness of the annealed steel with increasing soaking time. The yield strength, tensile strength, hardness and impact strength of the steel showed a continuous drop in value with increasing soaking time up to 60 minutes with a steep drop between 30 and 40 minutes. Ductility values followed the same decreasing trend up to 40 minutes soaking time after which the values started increasing again till 60 minutes soaking time. There was a linear relationship between the tensile strength and hardness of the material for different soaking times. This linear relationship was also observed for yield strength and hardness of the material.
基金supported by the National Natural Science Foundation of China(Grant Nos.51471123,51171135)the Natural Science Foundation of Shaanxi Province(Grant Nos.2012K07-08,2013KJXX-61)the Industrialization Program of Shaanxi Province(Grant No.2013JC14)
文摘The evolution of microstructure and texture for drawn polycrystalline Ag was investigated by transmission electron microscopy and electron backscattering diffraction.The results show that there are deformation twins and some un-tangled discrete dislocations at low strains.When the strain is increased to 0.58,a lot of high density dislocation walls and microbands come into being.At the same time,some twins lose the twinning relationship of 60°<111>.At a strain of 0.94,both dislocation boundaries and twin boundaries will rotate to the axis direction of wires and the shear bands start to appear.When the strain is higher than 1.96,most of the boundaries are parallel to the drawn direction.Texture analysis indicates that with the strain increasing,the volume fraction of complex texture component decreases,but<111>and<100>texture components increase.However,the variation in the volume fraction of each texture component as strains is not evident when the strains are higher than 0.58.For polycrystalline Ag with low stacking fault energy,complex texture components are easily formed.
