High geostress,a typical attribute of tunnels located at significant depths,is crucial in causing stress-induced failure and influencing the stability of the tunnel crown.This study developed an analytical method for ...High geostress,a typical attribute of tunnels located at significant depths,is crucial in causing stress-induced failure and influencing the stability of the tunnel crown.This study developed an analytical method for the failure mechanism that occurs in deep-buried tunnel roofs,taking into account the influence of geostress.The limit analysis theory was utilized for deriving analytical solutions about the geometry of the collapsing surface and the limit supporting pressure.The collapsing surface obtained by the analytical solution was validated by the findings of the physical model test,which shows a high level of agreement with the actual one.An extensive investigation was done to explore the effects of the lateral pressure coefficients,the tunnel buried depth,the geological conditions of the surrounding rock,the long-short axis ratio,and the size of the tunnel profile.The findings indicate that an increase in the lateral pressure coefficient from 0.5 to 1.5 results in a reduction in the height of the collapsing zone by 2.08 m and the width of the collapsing zone by 1.15 m,while simultaneously increases the limit supporting pressure by 18.9%.The proposed upper bound method accurately determines the limit supporting pressure and the geometry of the collapsing surface,which aligns well with the results acquired through numerical modelling and on-site monitoring in actual engineering applications.The proposed analytical method can serve as a reference for similar crown failure issues of deep-buried tunnels.展开更多
Post-collisional magmatism contains important clues for understanding the reworking and growth of continental crust,as well as lithospheric delamination and orogenic collapse.Early Devonian magmatism has been identifi...Post-collisional magmatism contains important clues for understanding the reworking and growth of continental crust,as well as lithospheric delamination and orogenic collapse.Early Devonian magmatism has been identified in the North Qilian Orogenic Belt(NQOB).This paper reports an integrated study of petrology,whole-rock geochemistry,Sm-Nd isotope and zircon U-Pb dating,as well as Lu-Hf isotopic data,for two Early Devonian intrusive plutons.The Yongchang and Chijin granites yield zircon U-Pb ages of 394-407 Ma and 414 Ma,respectively.Both of them are characterized by weakly peraluminous to metaluminous without typical aluminium-rich minerals,LREE-enriched patterns with negative Eu anomalies and a negative correlation between P_(2)O_(5) and SiO_(2) contents,consistent with geochemical features of I-type granitoids.Zircons from the studied granites display negative to weak positive ε_(Hf)(t)values(−5.7 to 2.1),which agree well with those of negative ε_(Nd)(t)values(−6.4 to−2.9)for the whole-rock samples,indicating that they were derived from the partial melting of Mesoproterozoic crust.Furthermore,low Sr/Y ratios(1.13-21.28)and high zircon saturation temperatures(745℃ to 839℃,with the majority being>800℃)demonstrated a relatively shallow depth level below the garnet stability field and an additional heat source.Taken together,the Early Devonian granitic magmatism could have been produced by the partial melting of ancient crustal materials heated by mantle-derived magmas at high-temperature and low-pressure conditions during postcollisional extensional collapse.The data obtained in this study,when viewed in conjunction with previous studies,provides more information about the tectonic processes that followed the closure of the North Qilian Ocean.The tectonic transition from continental collision to post-collisional delamination could be constrained to~430 Ma,which is provided by the sudden decrease of Sr/Y and La/Yb ratios and an increase in zircon ε_(Hf)(t)values for granitoids.A two-stage tectonic evolution model from continental collision to post-collisional extensional collapse for the NQOB includes(a)continental collision and crustal thickening during ca.455-430 Ma,characterized by granulite-facies metamorphism and widespread low-Mg adakitic magmatism;(b)post-collisional delamination of thickened continental crust and extensional collapse of orogen during ca.430-390 Ma,provided by coeval high-Mg adakitic magmatism,A-type granites and I-type granitoids with low Sr-Y ratios.展开更多
The present paper first investigates the collapse behavior of a conventional pipe-framed greenhouse under snow loading based on a 3-D finite element analysis,in which both geometrical and material non-linearities are ...The present paper first investigates the collapse behavior of a conventional pipe-framed greenhouse under snow loading based on a 3-D finite element analysis,in which both geometrical and material non-linearities are considered.Three snow load distribution patterns related to the wind-driven snow particle movement are used in the analysis.It is found that snow load distribution affects the deformation and collapse behavior of the pipe-framed greenhouse significantly.The results obtained in this study are consistent with the actual damage observed.Next,discussion is made of the effects of reinforcements by adding members to the basic frame on the strength of the whole structure,in which seven kinds of reinforcement methods are examined.A buckling analysis is also carried out.The results indicate that the most effective reinforcement method depends on the snow load distribution pattern.展开更多
A new staggered isolated system developed from the mid-story isolated system is the new staggered story isolated system. There are not many studies on this structure currently. In this study, an 18-story new staggered...A new staggered isolated system developed from the mid-story isolated system is the new staggered story isolated system. There are not many studies on this structure currently. In this study, an 18-story new staggered story isolated system model is established using SAP2000. The dynamic nonlinear dynamic alternate method is used to analyze the structure against progressive collapse. Results show that the structure has good resistance to progressive collapse, and there is no progressive collapse under each working condition. The progressive collapse does not occur for the case of removing only one vertical structural member of the new staggered of isolated system. The side column has big influence on this isolated structures’ progressive collapse;the removal of vertical structural member of the isolation layer has less impact on the structure than the removal of the bottom vertical structural member. After the removing of the member, the internal force of the structure will be redistributed, and the axial force of the adjacent columns will change obviously, showing a trend of “near large and far small”.展开更多
Objective: We constructed 3D-model of ONFH in computer according to three-dimensional computerized tomography (3D-CT) data. We determined the location and volume of necrosis to investigate its clinical efficacy. Metho...Objective: We constructed 3D-model of ONFH in computer according to three-dimensional computerized tomography (3D-CT) data. We determined the location and volume of necrosis to investigate its clinical efficacy. Method: Totally 92 hips (59 cases) with ONFH (44 males, 15 females) were included, with mean age of 37.5 years (range from 26 to 58). Totally 20 cases (35 hips) were induced by corticosteroid (CTSs), 31 (49 hips) induced by alcohol, 4 (4 hips) induced by trauma and 4 (4 hips) idiopathic. All the hips were categorized into stage ARCO II. Finally diagnosed by MRI, all hips were scanned by CT to acquire data in DICOM format. The images were imported into software to extract 3D-shape of femoral heads, necrotic foci, their volumes and distribution in each quadrant. Deviation of volumes between digital image and biopsy specimen was analyzed by SAS9.1 package. Correlativity between collapse and volume of necrosis under specific pathogeneses was also analyzed. Among the cases necessitating total hip arthroplasty (THA) due to advancing to ARCO III, we randomly selected 8 of them to perform 3D-CT scanning thrice prior to surgical operation. Total femoral heads harvested were torn asunder. Cubic capacity of femoral heads and necrotic foci were hereby measured and compared with those acquired from digital models. Result: Through the digital model, necrotic foci were found mainly locating within the super lateral portion of femoral head, coinciding with those observed in biopsy specimen. Average volumetric ratio of digitally acquired necrosis focus/femoral head in 58 collapsed hips was 36.8%. The ratio of the 34 hips without collapse was 17.3%. In collapsed femoral heads, the distribution of necrosis focus was 23.4% in quadrant 1 (q1), 23.6% in q2, 12.1% in q3, 14.4% in q4, 9.0% in q5, 11.8% in q6, 1.6% in q7 and 3.9% in q8. In femoral heads without collapse, the distribution was 34.2% in q1, 29.6% in q2, 11.8% in q3, 11.3% in q4, 6.0% in q5, 6.0% in q6, 0.5% in q7 and 0.4% in q8. As for the average cubic capacities of femoral heads and necrotic foci, those acquired from the digital model and biopsy specimen had no significant difference in matched-pairs test (t = -1.49, P = 0.179 for femoral heads and t = -1.52, P = 0.172 for necrotic foci). There was significant difference (F = 2.720, P = 0.035 P was respectively 0.0001 and 0.0005). Decision tree model showed that 94.6% (53/56) hips would progress into collapse if the volumetric ratio of necrotic tissue was over 23.48%. Otherwise, if distribution in q2 was over 45.13%, 83.3% (5/6) hips would progress into collapse. No collapse (0/30) would occur if the distribution of necrotic tissue in q2 was under 45.13%. Conclusion: Digital 3D-model reconstructed from CT scanning can precisely incarnate spatial orientation of necrotic foci in femoral head. Multinomial logistic regression and decision-making tree shows that volumetric ratio of necrotic tissues plays an important role in anticipating collapse of femoral head.展开更多
The detailed density perturbations provided by the advanced polarimeter-interferometer system(Polaris) during sawtooth collapse on the Joint Texas Experimental Tokamak(J-TEXT) are reported in this article.During a saw...The detailed density perturbations provided by the advanced polarimeter-interferometer system(Polaris) during sawtooth collapse on the Joint Texas Experimental Tokamak(J-TEXT) are reported in this article.During a sawtooth collapse and the crash of plasma pressure at the center,it is found that the increase in density in the region between the inversion radius and mixing radius is poloidally asymmetrical,while the increase in temperature is poloidally symmetrical.The poloidal location where the density increases is dependent on the phase of the precursory m/n=1/1 kink mode.It is always out of phase with the hot core of the m/n=1/1 mode.The behaviors of density perturbations during sawtooth collapse observed in J-TEXT are beyond the expectations of the standard model,and this can shed new light on the understanding of sawtooth collapse.展开更多
Sofar,slope collapse detectionmainlydepends onmanpower,whichhas the followingdrawbacks:(1)lowreliability,(2)high risk of human safe,(3)high labor cost.To improve the efficiency and reduce the human investment of slope...Sofar,slope collapse detectionmainlydepends onmanpower,whichhas the followingdrawbacks:(1)lowreliability,(2)high risk of human safe,(3)high labor cost.To improve the efficiency and reduce the human investment of slope collapse detection,this paper proposes an intelligent detection method based on deep learning technology for the task.In thismethod,we first use the deep learning-based image segmentation technology to find the slope area from the captured scene image.Then the foreground motion detection method is used for detecting the motion of the slope area.Finally,we design a lightweight convolutional neural network with an attentionmechanismto recognize the detected motion object,thus eliminating the interference motion and increasing the detection accuracy rate.Experimental results on the artificial data and relevant scene data show that the proposed detection method can effectively identify the slope collapse,which has its applicative value and brilliant prospect.展开更多
This paper presents experimental and numerical investigations on progressive collapse behavior of a two-story glulam frame when the side column is exposed to ISO834 standard fire.The collapse mechanism initiated by fi...This paper presents experimental and numerical investigations on progressive collapse behavior of a two-story glulam frame when the side column is exposed to ISO834 standard fire.The collapse mechanism initiated by fire is identified.The experimental results show that the progressive collapse of a glulam frame could be described for three stages,namely bending effect stage,catenary effect stage and failure stage,respectively.These stages are discussed in detail to understand the structural behavior before and during collapse.It is demonstrated that the entire frame slopes towards the side of the heated column,and the“overturning”collapse occurs eventually.The catenary effect of beams is the main reason for the progressive collapse of the frame.In addition,a finite element model of a glulam frame is established to simulate the progressive collapse behavior.The effects of axial loads on the columns are summarized.The numerical simulation results agree well with the experimental results,which could verify the effectiveness and practicability of finite element simulation.Furthermore,the progressive collapse resistance of the frame in practical design were proposed.展开更多
Due to the influence of multiple factors such as internal and external formation and mechanical pressure, medium corrosion and construction operation environment, a tubing collapse failure occurred in an oil well. In ...Due to the influence of multiple factors such as internal and external formation and mechanical pressure, medium corrosion and construction operation environment, a tubing collapse failure occurred in an oil well. In order to determine the failure cause of the tubing, physical and chemical tests and mechanical properties analysis were carried out on the failed tubing sample and the intact tubing. The results show that the chemical composition, ultrasonic and magnetic particle inspection, metallographic test, Charpy impact energy and external pressure mechanical property test of the failed tubing all meet the requirements of API Spec 5CT-2021 standard, but the yield strength of the failed tubing does not meet the requirements of API Spec 5CT-2021 standard. Through the analysis of the working conditions, it can be seen that the anti-extrusion strength of the tubing collapse does not meet the API 5C3 anti-extrusion strength standard. The failure type of the well tubing is tubing collapse caused by large internal and external pressure difference.展开更多
The vapor film collapse that occurs in the quenching process is complicated and affects the heat treatment quality and its distortion.In order to incorporate it into the MBD(Model Based Development)technology required...The vapor film collapse that occurs in the quenching process is complicated and affects the heat treatment quality and its distortion.In order to incorporate it into the MBD(Model Based Development)technology required these days,it is necessary to predict the quality of heat treatment by CAE(Computer Added Engineering),shorten the product development period.The calculation of the vapor film collapses in a simple and practical time in order to improve the product performance.However,in the past,in order to formulate the vapor film collapse on a simulation,it was necessary to perform a very large amount of computational calculation CFD(computational fluid dynamics),which was a problem in terms of computer resources and the model of vapor film collapse.In addition,this phenomenon has a complexity behavior of the phenomenon in iterative processing,which also complicates the calculation.In this study,the vapor film collapse phenomenon is easily visualized using self-organized cellular automaton simulation which includes the phenomena of“vapor film thickness and its fluctuation”,“flow disturbance”,“surface step of workpiece”,and“decrease of cooling due to r shape of surface”.The average cooling state and repeated fluctuations of the cooling state were reproduced by this method.展开更多
We present a case of stent graft collapse after performing thoracic endovascular aortic repair with a custom-made fenestrated stent graft. The patient was a 70-year-old woman with an asymptomatic aneurysm of the dista...We present a case of stent graft collapse after performing thoracic endovascular aortic repair with a custom-made fenestrated stent graft. The patient was a 70-year-old woman with an asymptomatic aneurysm of the distal aortic arch, and thoracic endovascular aortic repair was performed. The patient showed a blood pressure difference between the left arm and the right arm on postoperative day (POD) 17 prompting the performance of a chest computed tomography scan which revealed stent graft collapse. She then underwent staged debranching of thoracic endovascular aortic repair. Stent graft collapse is a rare but well-described complication of thoracic endovascular repair. Therefore, patients who undergo such a procedure should be carefully monitored for signs and symptoms, which suggest the possibility of stent collapse.展开更多
Airblasts,as one common phenomenon accompanied by rapid movements of landslides or rock/snow avalanches,commonly result in catastrophic damages and are attracting more and more scientific attention.To quantitatively a...Airblasts,as one common phenomenon accompanied by rapid movements of landslides or rock/snow avalanches,commonly result in catastrophic damages and are attracting more and more scientific attention.To quantitatively analyze the intensity of airblast initiated by landslides,the Wangjiayan landslide,occurred in the Wenchuan earthquake,is selected here with the landslide propagation and airblast evolution being studied using FLUENT by introducing the Voellmy rheological law.The results reveal that:(1)For the Wangjiayan landslide,its whole travelling duration is only 12 s with its maximum velocity reaching 36 m/s at t=10 s;(2)corresponding to the landslide propagation,the maximum velocity,28 m/s,of the airblast initiated by the landslide also appears at t=10 s with its maximum pressure reaching594.8 Pa,which is equivalent to violent storm;(3)under the attack of airblast,the load suffered by buildings in the airblast zone increases to 1300 Pa at t=9.4 s and sharply decreased to-7000 Pa as the rapid decrease of the velocity of the sliding mass at t=10 s,which is seriously unfavorable for buildings and might be the key reason for the destructive collapse of buildings in the airblast zone of the Wangjiayan landslide.展开更多
The Sound and the Fury is the novel which Faulkner spent the most effort and is the writer's favourite book. The title of this book is taken from Shakespeare's tragedy Macbeth, implying the multiple themes of ...The Sound and the Fury is the novel which Faulkner spent the most effort and is the writer's favourite book. The title of this book is taken from Shakespeare's tragedy Macbeth, implying the multiple themes of the novel. One theme is to discuss the corruption and collapse of the old southern traditional values through the description of the Compson family's corruption and the decline of southern plantation economy. In the novel, Faulkner seeks the way out for American south during the transformation period though the figures he created, but no one is successful in getting out of the bad influence of the Old South.展开更多
Loess soil deposits are widely distributed in arid and semi-arid regions and constitute about 10% of land area of the world.These soils typically have a loose honeycomb-type meta-stable structure that is susceptible t...Loess soil deposits are widely distributed in arid and semi-arid regions and constitute about 10% of land area of the world.These soils typically have a loose honeycomb-type meta-stable structure that is susceptible to a large reduction in total volume or collapse upon wetting.Collapse characteristics contribute to various problems to infrastructures that are constructed on loess soils.For this reason,collapse triggering mechanism for loess soils has been of significant interest for researchers and practitioners all over the world.This paper aims at providing a state-of-the-art review on collapse mechanism with special reference to loess soil deposits.The collapse mechanism studies are summarized under three different categories,i.e.traditional approaches,microstructure approach,and soil mechanics-based approaches.The traditional and microstructure approaches for interpreting the collapse behavior are comprehensively summarized and critically reviewed based on the experimental results from the literature.The soil mechanics-based approaches proposed based on the experimental results of both compacted soils and natural loess soils are reviewed highlighting their strengths and limitations for estimating the collapse behavior.Simpler soil mechanics-based approaches with less parameters or parameters that are easy-to-determine from conventional tests are suggested for future research to better understand the collapse behavior of natural loess soils.Such studies would be more valuable for use in conventional geotechnical engineering practice applications.展开更多
Loess soils are characterized by metastable microstructure, high porosity and water-sensitivity. These soils have always been problematic soils and attracted attention from researchers all over the world. In the prese...Loess soils are characterized by metastable microstructure, high porosity and water-sensitivity. These soils have always been problematic soils and attracted attention from researchers all over the world. In the present study, three loess soils extracted at various depths from the Loess Plateau of China, i.e. Malan(Q_3), upper Lishi(Q_2~2) and lower Lishi(Q_2~1) loess soils, were studied. Single oedometer-collapse tests were performed on intact loess specimens to investigate the collapse behavior of three loess soils. The microstructure and chemical composition of each loess before and after collapse test were characterized using scanning electron microscopy(i.e. SEM) and energy dispersive spectroscopy(i.e. EDS) techniques. The microstructural evolution due to wetting collapse was interpreted qualitatively and quantitatively in terms of the pore morphology properties. The results suggest that:(1) the collapse potential of each loess may rise again after a round of rise and drop, which could be failure of the new-developed stable structure under quite high vertical pressure. It implies that loess may collapse even if it has collapsed.(2) Q_3, Q_2~2 and Q_2~1 loess have different types of microstructure, namely, granule, aggregate and matrix type of microstructure, respectively.(3) The microstructural evolution due to loading and wetting is observed from a granule type to an aggregate type and finally to a matrix type of structure. The variations in distributions of pore morphology properties indicate that collapse leads to a transformation of large-sized pores into small-sized pores, re-orientation and remolding of soil pores due to particle rearrangement.(4) A porous structure is essential for loess collapse; however, the non-water-stability of bonding agents promotes the occurrence of collapse under the coupling effect of loading and wetting.展开更多
Casing collapse is one of the costly incidents in the oil industry. In the oil fields of southwest Iran, most casing collapses have occurred in Gachsaran formation, and the halite rock salt layer in this formation may...Casing collapse is one of the costly incidents in the oil industry. In the oil fields of southwest Iran, most casing collapses have occurred in Gachsaran formation, and the halite rock salt layer in this formation may be the main cause for these incidents because of its peculiar creep behavior. In this research, triaxial creep experiments have been conducted on Gachsaran salt samples under various temperatures and differential stresses. The main purpose was to determine the creep characteristics of Gachsaran rock salt,and to examine the role of creep in several casing collapses that occurred in this formation. Results indicated that the halite rock salt of Gachsaran formation basically obeys the power law;however, its creep parameters are quite different from other halite rocks elsewhere. The time-dependent creep of Gachsaran rock salt exhibits strong sensitivity to temperature change;however, its sensitivity to variation of differential stress is rather low. The numerical simulation of the rock salt creep in a real oil well demonstrated the importance of creep and reservoir conditions on the safety factor of the tubing related to casing collapse.展开更多
Reponses of structures subjected to severe earthquakes sometimes significantly surpass what was considered in the design.It is important to investigate the failure mechanism and collapse margin of structures beyond de...Reponses of structures subjected to severe earthquakes sometimes significantly surpass what was considered in the design.It is important to investigate the failure mechanism and collapse margin of structures beyond design,especially for high-rise buildings.In this study,steel high-rise buildings using either square concrete-filled-tube(CFT) columns or steel tube columns are designed.A detailed three-dimensional(3 D) structural model is developed to analyze the seismic behavior of a steel high-rise towards a complete collapse.The effectiveness is verified by both component tests and a full-scale shaking table test.The collapse margin,which is defined as the ratio of PGA between the collapse level to the design major earthquake level(Level 2),is quantified by a series of numerical simulations using incremental dynamic analyses(IDA).The baseline building using CFT columns collapsed with a weak first story mechanism and presented a collapse margin ranging from 10 to 20.The significant variation in the collapse margin was caused by the different characteristics of the input ground motions.The building using equivalent steel columns collapsed earlier due to the significant shortening of the locally buckled columns,exhibiting only 57% of the collapse margin of the baseline building.The influence of reducing the height of the first story was quite significant.The shortened first story not only enlarged the collapse margin by 20%,but also changed the collapse mode.展开更多
基金supported partially by the National Natural Science Foundation of China(42277158,41972277,and U1934212)。
文摘High geostress,a typical attribute of tunnels located at significant depths,is crucial in causing stress-induced failure and influencing the stability of the tunnel crown.This study developed an analytical method for the failure mechanism that occurs in deep-buried tunnel roofs,taking into account the influence of geostress.The limit analysis theory was utilized for deriving analytical solutions about the geometry of the collapsing surface and the limit supporting pressure.The collapsing surface obtained by the analytical solution was validated by the findings of the physical model test,which shows a high level of agreement with the actual one.An extensive investigation was done to explore the effects of the lateral pressure coefficients,the tunnel buried depth,the geological conditions of the surrounding rock,the long-short axis ratio,and the size of the tunnel profile.The findings indicate that an increase in the lateral pressure coefficient from 0.5 to 1.5 results in a reduction in the height of the collapsing zone by 2.08 m and the width of the collapsing zone by 1.15 m,while simultaneously increases the limit supporting pressure by 18.9%.The proposed upper bound method accurately determines the limit supporting pressure and the geometry of the collapsing surface,which aligns well with the results acquired through numerical modelling and on-site monitoring in actual engineering applications.The proposed analytical method can serve as a reference for similar crown failure issues of deep-buried tunnels.
基金supported by the Natural Science Foundation of Shandong Province(Grant No.ZR2022QD055)the Taishan Scholars(Grant No.tstp 20231214)the National Natural Science Foundation of China(Grant No.42372247).
文摘Post-collisional magmatism contains important clues for understanding the reworking and growth of continental crust,as well as lithospheric delamination and orogenic collapse.Early Devonian magmatism has been identified in the North Qilian Orogenic Belt(NQOB).This paper reports an integrated study of petrology,whole-rock geochemistry,Sm-Nd isotope and zircon U-Pb dating,as well as Lu-Hf isotopic data,for two Early Devonian intrusive plutons.The Yongchang and Chijin granites yield zircon U-Pb ages of 394-407 Ma and 414 Ma,respectively.Both of them are characterized by weakly peraluminous to metaluminous without typical aluminium-rich minerals,LREE-enriched patterns with negative Eu anomalies and a negative correlation between P_(2)O_(5) and SiO_(2) contents,consistent with geochemical features of I-type granitoids.Zircons from the studied granites display negative to weak positive ε_(Hf)(t)values(−5.7 to 2.1),which agree well with those of negative ε_(Nd)(t)values(−6.4 to−2.9)for the whole-rock samples,indicating that they were derived from the partial melting of Mesoproterozoic crust.Furthermore,low Sr/Y ratios(1.13-21.28)and high zircon saturation temperatures(745℃ to 839℃,with the majority being>800℃)demonstrated a relatively shallow depth level below the garnet stability field and an additional heat source.Taken together,the Early Devonian granitic magmatism could have been produced by the partial melting of ancient crustal materials heated by mantle-derived magmas at high-temperature and low-pressure conditions during postcollisional extensional collapse.The data obtained in this study,when viewed in conjunction with previous studies,provides more information about the tectonic processes that followed the closure of the North Qilian Ocean.The tectonic transition from continental collision to post-collisional delamination could be constrained to~430 Ma,which is provided by the sudden decrease of Sr/Y and La/Yb ratios and an increase in zircon ε_(Hf)(t)values for granitoids.A two-stage tectonic evolution model from continental collision to post-collisional extensional collapse for the NQOB includes(a)continental collision and crustal thickening during ca.455-430 Ma,characterized by granulite-facies metamorphism and widespread low-Mg adakitic magmatism;(b)post-collisional delamination of thickened continental crust and extensional collapse of orogen during ca.430-390 Ma,provided by coeval high-Mg adakitic magmatism,A-type granites and I-type granitoids with low Sr-Y ratios.
基金financially supported by the Steel Structure Research and Education Promotion Project of the Japan Iron and Steel Federation in FY2016.
文摘The present paper first investigates the collapse behavior of a conventional pipe-framed greenhouse under snow loading based on a 3-D finite element analysis,in which both geometrical and material non-linearities are considered.Three snow load distribution patterns related to the wind-driven snow particle movement are used in the analysis.It is found that snow load distribution affects the deformation and collapse behavior of the pipe-framed greenhouse significantly.The results obtained in this study are consistent with the actual damage observed.Next,discussion is made of the effects of reinforcements by adding members to the basic frame on the strength of the whole structure,in which seven kinds of reinforcement methods are examined.A buckling analysis is also carried out.The results indicate that the most effective reinforcement method depends on the snow load distribution pattern.
文摘A new staggered isolated system developed from the mid-story isolated system is the new staggered story isolated system. There are not many studies on this structure currently. In this study, an 18-story new staggered story isolated system model is established using SAP2000. The dynamic nonlinear dynamic alternate method is used to analyze the structure against progressive collapse. Results show that the structure has good resistance to progressive collapse, and there is no progressive collapse under each working condition. The progressive collapse does not occur for the case of removing only one vertical structural member of the new staggered of isolated system. The side column has big influence on this isolated structures’ progressive collapse;the removal of vertical structural member of the isolation layer has less impact on the structure than the removal of the bottom vertical structural member. After the removing of the member, the internal force of the structure will be redistributed, and the axial force of the adjacent columns will change obviously, showing a trend of “near large and far small”.
文摘Objective: We constructed 3D-model of ONFH in computer according to three-dimensional computerized tomography (3D-CT) data. We determined the location and volume of necrosis to investigate its clinical efficacy. Method: Totally 92 hips (59 cases) with ONFH (44 males, 15 females) were included, with mean age of 37.5 years (range from 26 to 58). Totally 20 cases (35 hips) were induced by corticosteroid (CTSs), 31 (49 hips) induced by alcohol, 4 (4 hips) induced by trauma and 4 (4 hips) idiopathic. All the hips were categorized into stage ARCO II. Finally diagnosed by MRI, all hips were scanned by CT to acquire data in DICOM format. The images were imported into software to extract 3D-shape of femoral heads, necrotic foci, their volumes and distribution in each quadrant. Deviation of volumes between digital image and biopsy specimen was analyzed by SAS9.1 package. Correlativity between collapse and volume of necrosis under specific pathogeneses was also analyzed. Among the cases necessitating total hip arthroplasty (THA) due to advancing to ARCO III, we randomly selected 8 of them to perform 3D-CT scanning thrice prior to surgical operation. Total femoral heads harvested were torn asunder. Cubic capacity of femoral heads and necrotic foci were hereby measured and compared with those acquired from digital models. Result: Through the digital model, necrotic foci were found mainly locating within the super lateral portion of femoral head, coinciding with those observed in biopsy specimen. Average volumetric ratio of digitally acquired necrosis focus/femoral head in 58 collapsed hips was 36.8%. The ratio of the 34 hips without collapse was 17.3%. In collapsed femoral heads, the distribution of necrosis focus was 23.4% in quadrant 1 (q1), 23.6% in q2, 12.1% in q3, 14.4% in q4, 9.0% in q5, 11.8% in q6, 1.6% in q7 and 3.9% in q8. In femoral heads without collapse, the distribution was 34.2% in q1, 29.6% in q2, 11.8% in q3, 11.3% in q4, 6.0% in q5, 6.0% in q6, 0.5% in q7 and 0.4% in q8. As for the average cubic capacities of femoral heads and necrotic foci, those acquired from the digital model and biopsy specimen had no significant difference in matched-pairs test (t = -1.49, P = 0.179 for femoral heads and t = -1.52, P = 0.172 for necrotic foci). There was significant difference (F = 2.720, P = 0.035 P was respectively 0.0001 and 0.0005). Decision tree model showed that 94.6% (53/56) hips would progress into collapse if the volumetric ratio of necrotic tissue was over 23.48%. Otherwise, if distribution in q2 was over 45.13%, 83.3% (5/6) hips would progress into collapse. No collapse (0/30) would occur if the distribution of necrotic tissue in q2 was under 45.13%. Conclusion: Digital 3D-model reconstructed from CT scanning can precisely incarnate spatial orientation of necrotic foci in femoral head. Multinomial logistic regression and decision-making tree shows that volumetric ratio of necrotic tissues plays an important role in anticipating collapse of femoral head.
基金supported by the National MCF Energy R&D Program of China (No.2018YFE0310300)National Natural Science Foundation of China (No.51821005)。
文摘The detailed density perturbations provided by the advanced polarimeter-interferometer system(Polaris) during sawtooth collapse on the Joint Texas Experimental Tokamak(J-TEXT) are reported in this article.During a sawtooth collapse and the crash of plasma pressure at the center,it is found that the increase in density in the region between the inversion radius and mixing radius is poloidally asymmetrical,while the increase in temperature is poloidally symmetrical.The poloidal location where the density increases is dependent on the phase of the precursory m/n=1/1 kink mode.It is always out of phase with the hot core of the m/n=1/1 mode.The behaviors of density perturbations during sawtooth collapse observed in J-TEXT are beyond the expectations of the standard model,and this can shed new light on the understanding of sawtooth collapse.
基金supported in part by the National Science Foundation of Guangxi Province under Grant 2021JJA170199and in part by the Research Project of Yellow River Engineer-ing Consulting with No.2021ky015.
文摘Sofar,slope collapse detectionmainlydepends onmanpower,whichhas the followingdrawbacks:(1)lowreliability,(2)high risk of human safe,(3)high labor cost.To improve the efficiency and reduce the human investment of slope collapse detection,this paper proposes an intelligent detection method based on deep learning technology for the task.In thismethod,we first use the deep learning-based image segmentation technology to find the slope area from the captured scene image.Then the foreground motion detection method is used for detecting the motion of the slope area.Finally,we design a lightweight convolutional neural network with an attentionmechanismto recognize the detected motion object,thus eliminating the interference motion and increasing the detection accuracy rate.Experimental results on the artificial data and relevant scene data show that the proposed detection method can effectively identify the slope collapse,which has its applicative value and brilliant prospect.
基金funded by the Jiangsu Province Science Fund for Distinguished Young Scholars(Grant No.BK20211536)Research Foundation of Nanjing Gongda Construction Technology Co.,Ltd.(Grant No.2021RD01).
文摘This paper presents experimental and numerical investigations on progressive collapse behavior of a two-story glulam frame when the side column is exposed to ISO834 standard fire.The collapse mechanism initiated by fire is identified.The experimental results show that the progressive collapse of a glulam frame could be described for three stages,namely bending effect stage,catenary effect stage and failure stage,respectively.These stages are discussed in detail to understand the structural behavior before and during collapse.It is demonstrated that the entire frame slopes towards the side of the heated column,and the“overturning”collapse occurs eventually.The catenary effect of beams is the main reason for the progressive collapse of the frame.In addition,a finite element model of a glulam frame is established to simulate the progressive collapse behavior.The effects of axial loads on the columns are summarized.The numerical simulation results agree well with the experimental results,which could verify the effectiveness and practicability of finite element simulation.Furthermore,the progressive collapse resistance of the frame in practical design were proposed.
文摘Due to the influence of multiple factors such as internal and external formation and mechanical pressure, medium corrosion and construction operation environment, a tubing collapse failure occurred in an oil well. In order to determine the failure cause of the tubing, physical and chemical tests and mechanical properties analysis were carried out on the failed tubing sample and the intact tubing. The results show that the chemical composition, ultrasonic and magnetic particle inspection, metallographic test, Charpy impact energy and external pressure mechanical property test of the failed tubing all meet the requirements of API Spec 5CT-2021 standard, but the yield strength of the failed tubing does not meet the requirements of API Spec 5CT-2021 standard. Through the analysis of the working conditions, it can be seen that the anti-extrusion strength of the tubing collapse does not meet the API 5C3 anti-extrusion strength standard. The failure type of the well tubing is tubing collapse caused by large internal and external pressure difference.
文摘The vapor film collapse that occurs in the quenching process is complicated and affects the heat treatment quality and its distortion.In order to incorporate it into the MBD(Model Based Development)technology required these days,it is necessary to predict the quality of heat treatment by CAE(Computer Added Engineering),shorten the product development period.The calculation of the vapor film collapses in a simple and practical time in order to improve the product performance.However,in the past,in order to formulate the vapor film collapse on a simulation,it was necessary to perform a very large amount of computational calculation CFD(computational fluid dynamics),which was a problem in terms of computer resources and the model of vapor film collapse.In addition,this phenomenon has a complexity behavior of the phenomenon in iterative processing,which also complicates the calculation.In this study,the vapor film collapse phenomenon is easily visualized using self-organized cellular automaton simulation which includes the phenomena of“vapor film thickness and its fluctuation”,“flow disturbance”,“surface step of workpiece”,and“decrease of cooling due to r shape of surface”.The average cooling state and repeated fluctuations of the cooling state were reproduced by this method.
文摘We present a case of stent graft collapse after performing thoracic endovascular aortic repair with a custom-made fenestrated stent graft. The patient was a 70-year-old woman with an asymptomatic aneurysm of the distal aortic arch, and thoracic endovascular aortic repair was performed. The patient showed a blood pressure difference between the left arm and the right arm on postoperative day (POD) 17 prompting the performance of a chest computed tomography scan which revealed stent graft collapse. She then underwent staged debranching of thoracic endovascular aortic repair. Stent graft collapse is a rare but well-described complication of thoracic endovascular repair. Therefore, patients who undergo such a procedure should be carefully monitored for signs and symptoms, which suggest the possibility of stent collapse.
基金supported by the National Natural Science Foundation of China(42322702,42177131)。
文摘Airblasts,as one common phenomenon accompanied by rapid movements of landslides or rock/snow avalanches,commonly result in catastrophic damages and are attracting more and more scientific attention.To quantitatively analyze the intensity of airblast initiated by landslides,the Wangjiayan landslide,occurred in the Wenchuan earthquake,is selected here with the landslide propagation and airblast evolution being studied using FLUENT by introducing the Voellmy rheological law.The results reveal that:(1)For the Wangjiayan landslide,its whole travelling duration is only 12 s with its maximum velocity reaching 36 m/s at t=10 s;(2)corresponding to the landslide propagation,the maximum velocity,28 m/s,of the airblast initiated by the landslide also appears at t=10 s with its maximum pressure reaching594.8 Pa,which is equivalent to violent storm;(3)under the attack of airblast,the load suffered by buildings in the airblast zone increases to 1300 Pa at t=9.4 s and sharply decreased to-7000 Pa as the rapid decrease of the velocity of the sliding mass at t=10 s,which is seriously unfavorable for buildings and might be the key reason for the destructive collapse of buildings in the airblast zone of the Wangjiayan landslide.
文摘The Sound and the Fury is the novel which Faulkner spent the most effort and is the writer's favourite book. The title of this book is taken from Shakespeare's tragedy Macbeth, implying the multiple themes of the novel. One theme is to discuss the corruption and collapse of the old southern traditional values through the description of the Compson family's corruption and the decline of southern plantation economy. In the novel, Faulkner seeks the way out for American south during the transformation period though the figures he created, but no one is successful in getting out of the bad influence of the Old South.
基金the Chinese Scholarship Council,which funded her Joint Ph D research programthe support from Natural Sciences and Engineering Research Council of Canada(NSERC)for his research programsthe Chinese Ministry of Science and Technology for supporting his research program(grant No.2014CB744701)
文摘Loess soil deposits are widely distributed in arid and semi-arid regions and constitute about 10% of land area of the world.These soils typically have a loose honeycomb-type meta-stable structure that is susceptible to a large reduction in total volume or collapse upon wetting.Collapse characteristics contribute to various problems to infrastructures that are constructed on loess soils.For this reason,collapse triggering mechanism for loess soils has been of significant interest for researchers and practitioners all over the world.This paper aims at providing a state-of-the-art review on collapse mechanism with special reference to loess soil deposits.The collapse mechanism studies are summarized under three different categories,i.e.traditional approaches,microstructure approach,and soil mechanics-based approaches.The traditional and microstructure approaches for interpreting the collapse behavior are comprehensively summarized and critically reviewed based on the experimental results from the literature.The soil mechanics-based approaches proposed based on the experimental results of both compacted soils and natural loess soils are reviewed highlighting their strengths and limitations for estimating the collapse behavior.Simpler soil mechanics-based approaches with less parameters or parameters that are easy-to-determine from conventional tests are suggested for future research to better understand the collapse behavior of natural loess soils.Such studies would be more valuable for use in conventional geotechnical engineering practice applications.
基金the National Key Research and Development Program of China (2017YFD0800501)the National Natural Science Foundation of China (Grant No. 41772323)+2 种基金the Shaanxi Science and Technology Bureau (Grant No.2016KW-030)the Geological Survey Bureau of China (DD20189270)the Key Laboratory for Geohazard in Loess Area, Ministry of Land and Resources (Grant No. KLGLAMLR201502)
文摘Loess soils are characterized by metastable microstructure, high porosity and water-sensitivity. These soils have always been problematic soils and attracted attention from researchers all over the world. In the present study, three loess soils extracted at various depths from the Loess Plateau of China, i.e. Malan(Q_3), upper Lishi(Q_2~2) and lower Lishi(Q_2~1) loess soils, were studied. Single oedometer-collapse tests were performed on intact loess specimens to investigate the collapse behavior of three loess soils. The microstructure and chemical composition of each loess before and after collapse test were characterized using scanning electron microscopy(i.e. SEM) and energy dispersive spectroscopy(i.e. EDS) techniques. The microstructural evolution due to wetting collapse was interpreted qualitatively and quantitatively in terms of the pore morphology properties. The results suggest that:(1) the collapse potential of each loess may rise again after a round of rise and drop, which could be failure of the new-developed stable structure under quite high vertical pressure. It implies that loess may collapse even if it has collapsed.(2) Q_3, Q_2~2 and Q_2~1 loess have different types of microstructure, namely, granule, aggregate and matrix type of microstructure, respectively.(3) The microstructural evolution due to loading and wetting is observed from a granule type to an aggregate type and finally to a matrix type of structure. The variations in distributions of pore morphology properties indicate that collapse leads to a transformation of large-sized pores into small-sized pores, re-orientation and remolding of soil pores due to particle rearrangement.(4) A porous structure is essential for loess collapse; however, the non-water-stability of bonding agents promotes the occurrence of collapse under the coupling effect of loading and wetting.
基金funded by Iran National Science Foundation (Grant No. 96001589 and contract No. 96002219)
文摘Casing collapse is one of the costly incidents in the oil industry. In the oil fields of southwest Iran, most casing collapses have occurred in Gachsaran formation, and the halite rock salt layer in this formation may be the main cause for these incidents because of its peculiar creep behavior. In this research, triaxial creep experiments have been conducted on Gachsaran salt samples under various temperatures and differential stresses. The main purpose was to determine the creep characteristics of Gachsaran rock salt,and to examine the role of creep in several casing collapses that occurred in this formation. Results indicated that the halite rock salt of Gachsaran formation basically obeys the power law;however, its creep parameters are quite different from other halite rocks elsewhere. The time-dependent creep of Gachsaran rock salt exhibits strong sensitivity to temperature change;however, its sensitivity to variation of differential stress is rather low. The numerical simulation of the rock salt creep in a real oil well demonstrated the importance of creep and reservoir conditions on the safety factor of the tubing related to casing collapse.
基金Heilongjiang Province Application Technology Research and Development under Grant No.GX16C007National Key Research and Development Program of China under Grant No.2017YFC1500605
文摘Reponses of structures subjected to severe earthquakes sometimes significantly surpass what was considered in the design.It is important to investigate the failure mechanism and collapse margin of structures beyond design,especially for high-rise buildings.In this study,steel high-rise buildings using either square concrete-filled-tube(CFT) columns or steel tube columns are designed.A detailed three-dimensional(3 D) structural model is developed to analyze the seismic behavior of a steel high-rise towards a complete collapse.The effectiveness is verified by both component tests and a full-scale shaking table test.The collapse margin,which is defined as the ratio of PGA between the collapse level to the design major earthquake level(Level 2),is quantified by a series of numerical simulations using incremental dynamic analyses(IDA).The baseline building using CFT columns collapsed with a weak first story mechanism and presented a collapse margin ranging from 10 to 20.The significant variation in the collapse margin was caused by the different characteristics of the input ground motions.The building using equivalent steel columns collapsed earlier due to the significant shortening of the locally buckled columns,exhibiting only 57% of the collapse margin of the baseline building.The influence of reducing the height of the first story was quite significant.The shortened first story not only enlarged the collapse margin by 20%,but also changed the collapse mode.