The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of...The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of CJRM is important for engineering construction.The Voronoi diagram and three-dimensional printing technology were used to make an irregular columnar jointed mold,and the irregular CJRM(ICJRM)specimens with different dip directions and dip angles were prepared.Uniaxial compression tests were performed,and the anisotropic strength and deformation characteristics of ICJRM were described.The failure modes and mechanisms were revealed in accordance with the final appearances of the ICJRM specimens.Based on the model test results,the empirical correlations for determining the field deformation and strength parameters of CJRM were derived using the dip angle and modified joint factor.The proposed empirical equations were used in the Baihetan Project,and the calculated mechanical parameters were compared with the field test results and those obtained from the tunneling quality index method.Results showed that the deformation parameters determined by the two proposed methods are all consistent with the field test results,and these two methods can also estimate the strength parameters effectively.展开更多
For a special geological structure of columnar jointed rock mass(CJRM),its mechanical properties are strongly affected by the columnar joints.To describe the fracture behaviors of CJRM using the basic theories of inte...For a special geological structure of columnar jointed rock mass(CJRM),its mechanical properties are strongly affected by the columnar joints.To describe the fracture behaviors of CJRM using the basic theories of interface mechanics for composite materials,the interface stresses of the vertical and horizontal joints,which are the two primary joints in the CJRM under triaxial compression,are studied,and their mathematical expressions are derived based on the superposition principle.Based on the obtained interface stresses of the vertical and horizontal joints in the CJRM,the crack initiation of the joint interface in the CJRM is studied using the maximum circumferential stress theory in fracture mechanics.Moreover,based on this investigation,the fracture behaviors of CJRM are analyzed.According to the results of similar material physical model tests for the CJRM,the theoretical study is verified.Finally,the influence of the mechanical parameters of the CJRM on the joint interface stress is discussed comprehensively.展开更多
The columnar jointed rock mass(CJR), composed of polygonal cross-sectional columns cut by several groups of joints in various directions, was exposed during the excavations of the Baihetan hydropower station, China. I...The columnar jointed rock mass(CJR), composed of polygonal cross-sectional columns cut by several groups of joints in various directions, was exposed during the excavations of the Baihetan hydropower station, China. In order to investigate the unloading performances and the stability conditions during excavation of the columns, an experimental field study was performed. Firstly, on-site investigations indicated that the geotechnical problems, including rock relaxation, cracking and collapse, were the most prominent for the CJR Class I that contains intensive joint network and the smallest column sizes.Comprehensive field tests, including deformation measurement by multi-point extensometers, ultrasonic wave testing, borehole television observation and stress monitoring of rock anchors, revealed that the time-dependent relaxation of the CJRs was marked. The practical excavation experiences for the Baihetan columnar jointed rock masses, such as blasting scheme, supporting time of shotcrete and rock bolts, were presented in the excavations of the diversion tunnels. These detailed investigations and practical construction experiences can provide helpful information for similar geotechnical works in jointed rock mass.展开更多
Columnar jointed basalt, with a lot of small-spacing structural planes and poor integrity, is a kind of fractured rock mass. Through comprehensive study of columnar joints shape, roughness of fracture surface and chem...Columnar jointed basalt, with a lot of small-spacing structural planes and poor integrity, is a kind of fractured rock mass. Through comprehensive study of columnar joints shape, roughness of fracture surface and chemical composition of basalt, it is known that columnar joints of Baihetan dam area were formed as a result of cooling and shrinkage effects of magma. The columnar jointed basalt is mainly formed through chemical reaction of chlorite, kaolinite, epidote and tremolite, and the columnar joints mainly consist of chlorite according to slice identification and chemical analysis. Test results show that the columnar jointed basalt has high uniaxial compressive strength, low friction coefficient, and high cohesion, shear strength and deformation index. Meanwhile, the columnar jointed basalt is closely locked, and joint surfaces are well closed. The permeability of the rock is quite weak, and the P-wave velocity in the rock could get up to 5 000 m/s. All these show good rock properties. The columnar joints develop regularly, different from the general fractured rock masses. In summary, the columnar jointed basalt can be used directly as a foundation of dam.展开更多
The West Junggar of the western Central Asian Orogenic Belt is one of the typical regions in the term of ocean subduction, contraction and continental growth in the Late Paleozoic. However, it is still controversial o...The West Junggar of the western Central Asian Orogenic Belt is one of the typical regions in the term of ocean subduction, contraction and continental growth in the Late Paleozoic. However, it is still controversial on the exact time of ocean-continent transition so far. This study investigates rhyolites with columnar joint in the West Junggar for the first time.Based on zircon U-Pb dating, we determined that the ages of the newly-discovered rhyolites are between 303.6 and 294.5 Ma, belonging to Late Carboniferous–Early Permian, which is the oldest rhyolite with columnar joint preserved in the world at present. Geochemical results show that the characteristics of the major element compositions include a high content of SiO_2(75.78–79.20 wt%) and a moderate content of Al_2O_3(12.21–13.19 wt%). The total alkali content(K_2O +Na_2O) is 6.14–8.05 wt%, among which K_2O is 2.09–4.72 wt% and the rate of K_2O/Na_2O is 0.38–3.05. Over-based minerals such as Ne, Lc, and Ac do not appear. The contents of TiO_2(0.09–0.24 wt%), CaO(0.15–0.99 wt%) and MgO(0.06–0.18 wt%) are low. A/CNK=0.91–1.68, A/NK=1.06–1.76, and as such, these are associated with the quasi-aluminum-weak peraluminous high potassium calc-alkaline and some calc-alkaline magma series. These rhyolites show a significant negative Eu anomaly with relative enrichment of LREE and LILE(Rb, Ba, Th, U, K) and depletion of Sr, HREE and HFSE(Nb, Ta, Ti, P). These rhyolites also have the characteristics of an A2-type granite, similar to the Miaoergou batholith,which indicates they both were affected by post-orogenic extension. Combining petrological, zircon U-Pb dating and geochemical characteristics of the rhyolites, we conclude that the specific time of ocean-continent transition of the West Junggar is the Late Carboniferous–Early Permian.展开更多
From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the A...From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the AUTOCAD model into 3DEC (3-dimensional distinct element code) model was developed, and a numerical model was established in 3DEC. Moreover, the results of triaxial compression tests of columnar jointed rock masses were simulated numerically. The REV (representative element volume) scale was studied, and the result shows that the REV size is 3 m × 3 m. The proposed approach, the established model and the numerical simulation were applied to study the macro-mechanical properties and the equivalent strength parameters of the columnar jointed rock mass. The numerical simulation results are in good accordance with the in-situ test results.展开更多
Columnar joints are regular columnar primary magmatic structure with polygonal cross sections developed in volcanic rocks which are commonly induced in cooling basaltic larva with low viscosity and high fluidity.In re...Columnar joints are regular columnar primary magmatic structure with polygonal cross sections developed in volcanic rocks which are commonly induced in cooling basaltic larva with low viscosity and high fluidity.In recent years,typical columnar joints in acidic volcanic rocks have been discovered in many other regions in China,including Quzhou area in Zhejiang Province,Siping and Shanmen area in Jilin Province.The latest studies on columnar joints revealed a different point of view on the展开更多
Irregular columnar jointed structure is a primary irregular columnar morphological tensile fracture. In order to study the geometric features of irregular columnar joints and the new problems in geotechnical engineeri...Irregular columnar jointed structure is a primary irregular columnar morphological tensile fracture. In order to study the geometric features of irregular columnar joints and the new problems in geotechnical engineering, hydraulic and hydropower engineering caused by columnar jointed basaltic mass, Voronoi graph from geometry was introduced to simulate the irregular columnar jointed basaltic mass at Baihetan hydraulic station. Discrete element software UDEC was used to simulate the whole process of rigid bearing plate test. Anisotropic constitutive of columnar joints was adopted to analyze the stress diffusion of rock mass at dam base of Baihetan. The results show that, the compaction property and hysteresis effect are well simulated based on discrete element simulation of Voronoi joint structure by UDEC. Four stages of cyclic loading and unloading process are imaged clearly. The results from in situ rigid bearing plate tests are explicated and the stress diffusion rule of anisotropic body is affected by structure surface. The elements in the stress state of 4-5 MPa are the most, about more than 35% of the total. Appropriate constitutive must be proposed to columnar jointed rock mass with different styles. It has important significance to realize the nonlinear mechanical behavior of irregular columnar jointed basaltic mass.展开更多
Columnar jointed basalt(CJB) widely distributes in the dam site of the Baihetan Hydropower Station.The columnar joint structure and fracture development of CJB have significant influence on the mechanical properties o...Columnar jointed basalt(CJB) widely distributes in the dam site of the Baihetan Hydropower Station.The columnar joint structure and fracture development of CJB have significant influence on the mechanical properties of rock mass,and the mechanical properties of CJB are of great significance to the Baihetan Hydropower Project.Therefore,in-situ direct shear tests were carried out on ten test adit at different locations in the dam site area to study the shear behavior of CJB.In this study,21 sets of in-situ direct shear tests were conducted for rock types of type Ⅱ_(2),type Ⅲ_(1)and type Ⅲ_(2),with horizontal and vertical shear planes and two different specimen sizes of CJB.Shear strength parameters of CJB were obtained by linear fitting of in-situ direct shear test results based on the Mohr-Coulomb strength criterion.The results indicate that the shear strength parameters of CJB with horizontal shear plane increase as the increase of rock type grade.The shear strength parameters of CJB show obvious anisotropy and the friction coefficient of the horizontal shear plane is greater than the vertical shear plane.The friction coefficient in the horizontal direction of the shear plane is 1.27 times that in the vertical direction of the shear plane.With the increase of rock type grade,the difference of friction coefficient becomes larger.However,the cohesion changes little whether the shear plane is horizontal or vertical.In addition,the size effect of CJB in this area is significant.The shear strength parameters of large size(100 cm × 100 cm) specimens are lower than those of regular size(50 cm × 50 cm) specimens.The reduction of cohesion is greater than that of the friction coefficient.For rock type Ⅲ_(2),the cohesion of large-size specimens is 0.637 of the regular-size specimens.The reduction percentage of the friction coefficient for type Ⅲ_(2)is 1.66 times that of type Ⅲ_(1).The reduction percentage of the cohesion for type Ⅲ_(2)is 1.27 times that of type Ⅲ_(1).The size effect decreases with the increase of rock type grade.The research results of this study can provide an important basis for the selection of rock mechanics parameters in the dam site area of Baihetan Hydropower Station and the stability analysis of the dam foundation and rocky slopes.展开更多
To evaluate the columnar jointed basalts in the dam site of Baihetan hydropower station in southwest China, we developed a basic conceptual model of single jointed rock mass. Considering that the rock mass deformation...To evaluate the columnar jointed basalts in the dam site of Baihetan hydropower station in southwest China, we developed a basic conceptual model of single jointed rock mass. Considering that the rock mass deformation consists of rock block deformation and joints deformation, the linear mechanical characteristics of the cell (including the elastic joints and the nonlinear mechanical behaviors of the cell) with a combined frictional-elastic interface were analyzed. We developed formulas to calculate the rock block deformation, which can be adapted for multiple jointed rock mass and columnar jointed basalts. The formulas are effective in calculating the equivalent modulus of multiple jointed rock mass, and precisely reveal the anisotropic properties of columnar jointed basalts. Furthermore, the in situ rigid bearing plate tests were analyzed and calculated, and the types of loading-unloading curves and the equivalent modulus along different directions of columnar jointed basalts were obtained. The analytical results are in close compliance with the test results.展开更多
Rubbly pahoehoe lava flows are abundant in many continental flood basalts including the Deccan Traps.However,structures with radial joint columns surrounding cores of flow-top breccia(FTB),reported from some Deccan ru...Rubbly pahoehoe lava flows are abundant in many continental flood basalts including the Deccan Traps.However,structures with radial joint columns surrounding cores of flow-top breccia(FTB),reported from some Deccan rubbly pahoehoe flows,are yet unknown from other basaltic provinces.A previous study of these Deccan "breccia-cored columnar rosettes" ruled out explanations such as volcanic vents and lava tubes,and showed that the radial joint columns had grown outwards from cold FTB inclusions incorporated into the hot molten interiors.How the highly vesicular(thus low-density)FTB blocks might have sunk into the flow interiors has remained a puzzle.Here we describe a new example of a Deccan rubbly pahoehoe flow with FTB-cored rosettes,from Elephanta Island in the Mumbai harbor.Noting that(1)thick rubbly pahoehoe flows probably form by rapid inflation(involving many lava injections into a largely molten advancing flow),and(2)such flows are transitional to 'a'a flows(which continuously shed their top clinker in front of them as they advance),we propose a model for the FTB-cored rosettes.We suggest that the Deccan flows under study were shedding some of their FTB in front of them as they advanced and,with high-eruption rate lava injection and inflation,frontal breakouts would incorporate this FTB rubble,with thickening of the flow carrying the rubble into the flow interior.This implies that,far from sinking into the molten interior,the FTB blocks may have been rising,until lava supply and inflation stopped,the flow began solidifying,and joint columns developed outward from each cold FTB inclusion as already inferred,forming the FTB-cored rosettes.Those rubbly pahoehoe flows which began recycling most of their FTB became the 'a'a flows of the Deccan.展开更多
基金This work was supported by the Fundamental Research Funds for the Central Universities,the Postgraduate Research&Practice Innovation Program of Jiangsu Province(Grant No.KYCX21_0487)the National Natural Science Foundation of China(Grant Nos.41831278,and 51579081).
文摘The irregularity of jointed network poses a challenge to the determination of field mechanical param-eters of columnar jointed rock mass(CJRM),and a reasonable prediction of deformation and strength characteristics of CJRM is important for engineering construction.The Voronoi diagram and three-dimensional printing technology were used to make an irregular columnar jointed mold,and the irregular CJRM(ICJRM)specimens with different dip directions and dip angles were prepared.Uniaxial compression tests were performed,and the anisotropic strength and deformation characteristics of ICJRM were described.The failure modes and mechanisms were revealed in accordance with the final appearances of the ICJRM specimens.Based on the model test results,the empirical correlations for determining the field deformation and strength parameters of CJRM were derived using the dip angle and modified joint factor.The proposed empirical equations were used in the Baihetan Project,and the calculated mechanical parameters were compared with the field test results and those obtained from the tunneling quality index method.Results showed that the deformation parameters determined by the two proposed methods are all consistent with the field test results,and these two methods can also estimate the strength parameters effectively.
基金funding support from National Natural Science Foundation of China(Grant No.41831278).
文摘For a special geological structure of columnar jointed rock mass(CJRM),its mechanical properties are strongly affected by the columnar joints.To describe the fracture behaviors of CJRM using the basic theories of interface mechanics for composite materials,the interface stresses of the vertical and horizontal joints,which are the two primary joints in the CJRM under triaxial compression,are studied,and their mathematical expressions are derived based on the superposition principle.Based on the obtained interface stresses of the vertical and horizontal joints in the CJRM,the crack initiation of the joint interface in the CJRM is studied using the maximum circumferential stress theory in fracture mechanics.Moreover,based on this investigation,the fracture behaviors of CJRM are analyzed.According to the results of similar material physical model tests for the CJRM,the theoretical study is verified.Finally,the influence of the mechanical parameters of the CJRM on the joint interface stress is discussed comprehensively.
基金the financial support from the International Partnership Program of Chinese Academy of Sciences(Grant No.115242KYSB20160017)the Key Project of Natural Science Foundation of China(Grant No.11232014)National Natural Science Foundation of China(Grant No.51379202)
文摘The columnar jointed rock mass(CJR), composed of polygonal cross-sectional columns cut by several groups of joints in various directions, was exposed during the excavations of the Baihetan hydropower station, China. In order to investigate the unloading performances and the stability conditions during excavation of the columns, an experimental field study was performed. Firstly, on-site investigations indicated that the geotechnical problems, including rock relaxation, cracking and collapse, were the most prominent for the CJR Class I that contains intensive joint network and the smallest column sizes.Comprehensive field tests, including deformation measurement by multi-point extensometers, ultrasonic wave testing, borehole television observation and stress monitoring of rock anchors, revealed that the time-dependent relaxation of the CJRs was marked. The practical excavation experiences for the Baihetan columnar jointed rock masses, such as blasting scheme, supporting time of shotcrete and rock bolts, were presented in the excavations of the diversion tunnels. These detailed investigations and practical construction experiences can provide helpful information for similar geotechnical works in jointed rock mass.
基金Supported by the National Natural Science Foundation of China (41172254)the Opening Fund of State Key Laboratory of Geohazard Prevention and Geoenvironment Protection, Chengdu University of Technology (SKLGP2010K020)
文摘Columnar jointed basalt, with a lot of small-spacing structural planes and poor integrity, is a kind of fractured rock mass. Through comprehensive study of columnar joints shape, roughness of fracture surface and chemical composition of basalt, it is known that columnar joints of Baihetan dam area were formed as a result of cooling and shrinkage effects of magma. The columnar jointed basalt is mainly formed through chemical reaction of chlorite, kaolinite, epidote and tremolite, and the columnar joints mainly consist of chlorite according to slice identification and chemical analysis. Test results show that the columnar jointed basalt has high uniaxial compressive strength, low friction coefficient, and high cohesion, shear strength and deformation index. Meanwhile, the columnar jointed basalt is closely locked, and joint surfaces are well closed. The permeability of the rock is quite weak, and the P-wave velocity in the rock could get up to 5 000 m/s. All these show good rock properties. The columnar joints develop regularly, different from the general fractured rock masses. In summary, the columnar jointed basalt can be used directly as a foundation of dam.
基金supported by the China Geological Survey (grant numbers DD20160083 and DD20160344-05)the National Key Research and Development Program of China (grant numbers 2018YFC0603701)Fundamental Research Funds for Central Public Welfare Research Institutes (grant numbers CAGS-YWF201706)
文摘The West Junggar of the western Central Asian Orogenic Belt is one of the typical regions in the term of ocean subduction, contraction and continental growth in the Late Paleozoic. However, it is still controversial on the exact time of ocean-continent transition so far. This study investigates rhyolites with columnar joint in the West Junggar for the first time.Based on zircon U-Pb dating, we determined that the ages of the newly-discovered rhyolites are between 303.6 and 294.5 Ma, belonging to Late Carboniferous–Early Permian, which is the oldest rhyolite with columnar joint preserved in the world at present. Geochemical results show that the characteristics of the major element compositions include a high content of SiO_2(75.78–79.20 wt%) and a moderate content of Al_2O_3(12.21–13.19 wt%). The total alkali content(K_2O +Na_2O) is 6.14–8.05 wt%, among which K_2O is 2.09–4.72 wt% and the rate of K_2O/Na_2O is 0.38–3.05. Over-based minerals such as Ne, Lc, and Ac do not appear. The contents of TiO_2(0.09–0.24 wt%), CaO(0.15–0.99 wt%) and MgO(0.06–0.18 wt%) are low. A/CNK=0.91–1.68, A/NK=1.06–1.76, and as such, these are associated with the quasi-aluminum-weak peraluminous high potassium calc-alkaline and some calc-alkaline magma series. These rhyolites show a significant negative Eu anomaly with relative enrichment of LREE and LILE(Rb, Ba, Th, U, K) and depletion of Sr, HREE and HFSE(Nb, Ta, Ti, P). These rhyolites also have the characteristics of an A2-type granite, similar to the Miaoergou batholith,which indicates they both were affected by post-orogenic extension. Combining petrological, zircon U-Pb dating and geochemical characteristics of the rhyolites, we conclude that the specific time of ocean-continent transition of the West Junggar is the Late Carboniferous–Early Permian.
基金Projects(50911130366, 50979030) supported by the National Natural Science Foundation of China
文摘From the geological structure of the columnar jointed rock mass, a visual model was established in software AUTOCAD by programming based on the algorithm of the Voronoi diagram. Furthermore, a program to convert the AUTOCAD model into 3DEC (3-dimensional distinct element code) model was developed, and a numerical model was established in 3DEC. Moreover, the results of triaxial compression tests of columnar jointed rock masses were simulated numerically. The REV (representative element volume) scale was studied, and the result shows that the REV size is 3 m × 3 m. The proposed approach, the established model and the numerical simulation were applied to study the macro-mechanical properties and the equivalent strength parameters of the columnar jointed rock mass. The numerical simulation results are in good accordance with the in-situ test results.
文摘Columnar joints are regular columnar primary magmatic structure with polygonal cross sections developed in volcanic rocks which are commonly induced in cooling basaltic larva with low viscosity and high fluidity.In recent years,typical columnar joints in acidic volcanic rocks have been discovered in many other regions in China,including Quzhou area in Zhejiang Province,Siping and Shanmen area in Jilin Province.The latest studies on columnar joints revealed a different point of view on the
基金Projects(50979030, 50911130366) supported by the National Natural Science Foundation of ChinaProject(2009B14014) supported by the Fundamental Research Funds for the Central Universities in China
文摘Irregular columnar jointed structure is a primary irregular columnar morphological tensile fracture. In order to study the geometric features of irregular columnar joints and the new problems in geotechnical engineering, hydraulic and hydropower engineering caused by columnar jointed basaltic mass, Voronoi graph from geometry was introduced to simulate the irregular columnar jointed basaltic mass at Baihetan hydraulic station. Discrete element software UDEC was used to simulate the whole process of rigid bearing plate test. Anisotropic constitutive of columnar joints was adopted to analyze the stress diffusion of rock mass at dam base of Baihetan. The results show that, the compaction property and hysteresis effect are well simulated based on discrete element simulation of Voronoi joint structure by UDEC. Four stages of cyclic loading and unloading process are imaged clearly. The results from in situ rigid bearing plate tests are explicated and the stress diffusion rule of anisotropic body is affected by structure surface. The elements in the stress state of 4-5 MPa are the most, about more than 35% of the total. Appropriate constitutive must be proposed to columnar jointed rock mass with different styles. It has important significance to realize the nonlinear mechanical behavior of irregular columnar jointed basaltic mass.
基金supported by the National Key Research and Development Program of China (No.2017YFC1501302)the National Natural Science Foundation of China (No.41630643)+1 种基金the Fundamental Research Funds for the Central Universities (No.CUGCJ1701)the Scientific research project of China Three Gorges Corporation Ltd。
文摘Columnar jointed basalt(CJB) widely distributes in the dam site of the Baihetan Hydropower Station.The columnar joint structure and fracture development of CJB have significant influence on the mechanical properties of rock mass,and the mechanical properties of CJB are of great significance to the Baihetan Hydropower Project.Therefore,in-situ direct shear tests were carried out on ten test adit at different locations in the dam site area to study the shear behavior of CJB.In this study,21 sets of in-situ direct shear tests were conducted for rock types of type Ⅱ_(2),type Ⅲ_(1)and type Ⅲ_(2),with horizontal and vertical shear planes and two different specimen sizes of CJB.Shear strength parameters of CJB were obtained by linear fitting of in-situ direct shear test results based on the Mohr-Coulomb strength criterion.The results indicate that the shear strength parameters of CJB with horizontal shear plane increase as the increase of rock type grade.The shear strength parameters of CJB show obvious anisotropy and the friction coefficient of the horizontal shear plane is greater than the vertical shear plane.The friction coefficient in the horizontal direction of the shear plane is 1.27 times that in the vertical direction of the shear plane.With the increase of rock type grade,the difference of friction coefficient becomes larger.However,the cohesion changes little whether the shear plane is horizontal or vertical.In addition,the size effect of CJB in this area is significant.The shear strength parameters of large size(100 cm × 100 cm) specimens are lower than those of regular size(50 cm × 50 cm) specimens.The reduction of cohesion is greater than that of the friction coefficient.For rock type Ⅲ_(2),the cohesion of large-size specimens is 0.637 of the regular-size specimens.The reduction percentage of the friction coefficient for type Ⅲ_(2)is 1.66 times that of type Ⅲ_(1).The reduction percentage of the cohesion for type Ⅲ_(2)is 1.27 times that of type Ⅲ_(1).The size effect decreases with the increase of rock type grade.The research results of this study can provide an important basis for the selection of rock mechanics parameters in the dam site area of Baihetan Hydropower Station and the stability analysis of the dam foundation and rocky slopes.
基金Project (Nos. 50911130366 and 2011CB013504) supported by the National Natural Science Foundation of Chinathe Postdoctoral Advanced Research Programs Class Ⅱ of Zhejiang Province (No. BSH1302013), China
文摘To evaluate the columnar jointed basalts in the dam site of Baihetan hydropower station in southwest China, we developed a basic conceptual model of single jointed rock mass. Considering that the rock mass deformation consists of rock block deformation and joints deformation, the linear mechanical characteristics of the cell (including the elastic joints and the nonlinear mechanical behaviors of the cell) with a combined frictional-elastic interface were analyzed. We developed formulas to calculate the rock block deformation, which can be adapted for multiple jointed rock mass and columnar jointed basalts. The formulas are effective in calculating the equivalent modulus of multiple jointed rock mass, and precisely reveal the anisotropic properties of columnar jointed basalts. Furthermore, the in situ rigid bearing plate tests were analyzed and calculated, and the types of loading-unloading curves and the equivalent modulus along different directions of columnar jointed basalts were obtained. The analytical results are in close compliance with the test results.
文摘Rubbly pahoehoe lava flows are abundant in many continental flood basalts including the Deccan Traps.However,structures with radial joint columns surrounding cores of flow-top breccia(FTB),reported from some Deccan rubbly pahoehoe flows,are yet unknown from other basaltic provinces.A previous study of these Deccan "breccia-cored columnar rosettes" ruled out explanations such as volcanic vents and lava tubes,and showed that the radial joint columns had grown outwards from cold FTB inclusions incorporated into the hot molten interiors.How the highly vesicular(thus low-density)FTB blocks might have sunk into the flow interiors has remained a puzzle.Here we describe a new example of a Deccan rubbly pahoehoe flow with FTB-cored rosettes,from Elephanta Island in the Mumbai harbor.Noting that(1)thick rubbly pahoehoe flows probably form by rapid inflation(involving many lava injections into a largely molten advancing flow),and(2)such flows are transitional to 'a'a flows(which continuously shed their top clinker in front of them as they advance),we propose a model for the FTB-cored rosettes.We suggest that the Deccan flows under study were shedding some of their FTB in front of them as they advanced and,with high-eruption rate lava injection and inflation,frontal breakouts would incorporate this FTB rubble,with thickening of the flow carrying the rubble into the flow interior.This implies that,far from sinking into the molten interior,the FTB blocks may have been rising,until lava supply and inflation stopped,the flow began solidifying,and joint columns developed outward from each cold FTB inclusion as already inferred,forming the FTB-cored rosettes.Those rubbly pahoehoe flows which began recycling most of their FTB became the 'a'a flows of the Deccan.