Effects of water intrusion and loading rate on mechanical properties of and crack propagation in coal–rock combinations

Tackling the problems of underground water storage in collieries in arid regions requires knowledge of the effect of water intrusion and loading rate on the mechanical properties of and crack development in coal–rock combinations. Fifty-four coal–rock combinations were prepared and split equally into groups containing different moisture contents(dry, natural moisture and saturated) to conduct acoustic emission testing under uniaxial compression with loading rates ranging from 0.1 mm/min to 0.6 mm/min. The results show that the peak stress and strength-softening modulus, elastic modulus, strain-softening modulus, and post-peak modulus partly decrease with increasing moisture content and loading rate. In contrast, peak strain increases with increasing moisture content and fluctuates with rising loading rate. More significantly, the relationship between stiffness and stress, combined with accumulated counts of acoustic emission, can be used to precisely predict all phases of crack propagation. This is helpful in studying the impact of moisture content and loading rate on crack propagation and accurately calculating mechanical properties. We also determined that the stress thresholds of crack closure, crack initiation, and crack damage do not vary with changes of moisture content and loading rate, constituting 15.22%, 32.20%, and 80.98% of peak stress, respectively. These outcomes assist in developing approaches to water storage in coal mines, determining the necessary width of waterproof coal–rock pillars, and methods of supporting water-enriched roadways, while also advances understanding the mechanical properties of coal–rock combinations and laws of crack propagation.

Evaluation of Farmland Drainage Water Quality by Fuzzy–Gray Combination Method

The complex relationships between indicators and water conditions cause fuzzy and gray uncertainties in evaluation of water quality. Compared to conventional single-factor evaluation methods, the combination evaluation method can consider these two uncertainties to produce more objective and reasonable evaluation results. In this paper, we propose a combination evaluation method with two main parts:(1) the use of fuzzy comprehensive evaluation and gray correlation analysis as submodels with which to consider the fuzzy and gray uncertainties and(2) the establishment of a combination model based on minimum bias squares. In addition, using this method, we evaluate the water quality of a ditch in a typical rice–wheat system of Yixing city in the Taihu Lake Basin during three rainfall events. The results show that the ditch water quality is not good and we found the chemical oxygen demand to be the key indicator that affects water quality most significantly. The proposed combination evaluation method is more accurate and practical than single-factor evaluation methods in that it considers the uncertainties of fuzziness and grayness.

Pore-Throat Combination Types and Gas-Water Relative Permeability Responses of Tight Gas Sandstone Reservoirs in the Zizhou Area of East Ordos Basin, China

With the aim of better understanding the tight gas reservoirs in the Zizhou area of east Ordos Basin,a total of 222 samples were collected from 50 wells for a series of experiments.In this study,three pore-throat combination types in sandstones were revealed and confirmed to play a controlling role in the distribution of throat size and the characteristics of gas-water relative permeability.The type-I sandstones are dominated by intercrystalline micropores connected by cluster throats,of which the distribution curves of throat size are narrow and have a strong single peak(peak ratio>30%).The pores in the type-II sandstones dominantly consist of secondary dissolution pores and intercrystalline micropores,and throats mainly occur as slice-shaped throats along cleavages between rigid grain margins and cluster throats in clay cement.The distribution curves of throat size for the type-II sandstones show a bimodal distribution with a substantial low-value region between the peaks(peak ratio<15%).Primary intergranular pores and secondary intergranular pores are mainly found in type-III samples,which are connected by various throats.The throat size distribution curves of type-III sandstones show a nearly normal distribution with low kurtosis(peak ratio<10%),and the micro-scale throat radii(>0.5μm)constitute a large proportion.From type-I to type-III sandstones,the irreducible water saturation(Swo)decreased;furthermore,the slope of the curves of Krw/Krg in two-phase saturation zone decreased and the two-phase saturation zone increased,indicating that the gas relative flow ability increased.Variations of the permeability exist in sandstones with different porethroat combination types,which indicate the type-III sandstones are better reservoirs,followed by type-II sandstones and type-I sandstones.As an important factor affecting the reservoir quality,the pore-throat combination type in sandstones is the cumulative expression of lithology and diagenetic modifications with strong heterogeneity.

Strengthening pelletization of manganese ore fines containing high combined water by high pressure roll grinding and optimized temperature elevation system

Pelletization is one of useful processes for the agglomeration of iron ore or concentrates. However, manganese ore fines are mainly agglomerated by sintering due to its high combined water which adversely affects the roasting performance of pellets. In this work, high pressure roll grinding(HPRG) process and optimization of temperature elevation system were investigated to improve the strength of fired manganese ore pellets. It is shown that the manganese ore possesses good ballability after being pretreated by HPRG twice, and good green balls were produced under the conditions of blending 2.0% bentonite in the feed, balling for 7 min at 16.00% moisture. High quality roasted pellets with the compressive strength of 2711 N per pellet were manufactured through preheating at 1050 °C for 10 min and firing at 1335 °C for 15 min by controlling the cracks formation. The fired manganese pellets keep the strength by the solid interconnection of recrystallized pyrolusite grains and the binding of manganite liquid phase which filled the pores and clearance among minerals. The product pellets contain high Mn grade and low impurities, and can be used to smelt ferromanganese, which provides a possible way to use imported manganese ore fines containing high combined water to produce high value ferromanganese.

Produced-water treatment: Application and research of combined fiber coalescence technique in offshore oilfield

When the process of extraction of oil from an offshore oilfield enters the advanced stages,the water content in the extracted fluid can be above 90%.The water quality is complex with many types of pollutants and highly emulsified water.Therefore,a key consideration in the production process of offshore oilfields is the efficient and economical treatment of the oil-containing produced water to make it suitable for discharge and recover oil pollutants.In this study,we developed a hydrophilic and hydrophobic combined fiber coalescence separator with composite fiber shapes using fiber induction and X/Uweaving.The separator is designed based on experimental observations of the mechanism of structure coalescence in the physical oil removal method.A pilot test was performed on an oil exploration platform in the Bohai Sea.At the designed flow rate,the separator reduced the total concentration of petroleum in the produced water from 2000 to 3000 mg/L to below 60 mg/L,with an average oil removal efficiency of 98.24%.Furthermore,it effectively reduced the number of organic compounds present in the water from 120 to 17 and removed 70% of the SS.The test results show that the proposed device can be used fr produced-water treatment on offshore platforms.

Effects of Combined Organic-inorganic Fertilization on Quality and Water Use Efficiency of Spring Maize under Equal Nitrogen Fertilization

The experiment was conducted in the abandoned land of Liangjia Village,Huayin City,Shaanxi Province from April to September 2019.The experimental crop was spring maize.A total of six treatments were set up in a randomized block design.The moisture content of the top 0-60 cm soil was determined regularly,and the yield and quality indices of maize at maturity were checked.The results show that:(i)combined organic-inorganic fertilization increased the yield of spring maize by 3%-8%.(ii)Compared with CK,fertilization treatments significantly improved the water use efficiency of spring maize,with an increase of 59.2%.The average water use efficiency of three combined organic-inorganic fertilization treatments was 27.81 kg/(ha·mm).Compared with CON,combined application of organic and inorganic fertilizers significantly improved the water use efficiency of spring maize,with an increase of 12.5%.(iii)The combined application of organic and inorganic fertilizers increased the moisture,total starch,crude protein and crude fat contents,and reduced crude fiber content of maize kernels.However,with the increase of the proportion of organic fertilizer,the crude protein content of maize kernels decreased.(iv)Yield of spring maize showed a significant parabolic relationship with soil water consumption.In summary,70%inorganic fertilizer+30%organic fertilizer is a scientific and reasonable way of fertilization.

Construction and Application of Combined Evaluation Model of Regional Water Quality Plan

[Objective] The aim was to study the construction and application of combined evaluation model of regional water quality plan. [Meth- od] By dint of layer analysis, subjective and objective model of entropy evaluation, the water quality plan in Jinghe was evaluated. Combined evalu- ation model based on information entropy were constructed, and considering the single model evaluation result, the optimal water quality plan was selected. [ Result] The combination weight result suggested that COD amount was the most essential indicator in water quality plan and embodied the importance of water environment protection, which met basic objective of environment protection and social, economic effects. Combined evalu- ation indicated that in the sixteen plans, plan 16 was of highest comprehensive evaluation value, and can be considered as optimum water quality plan. [ Conclusion] Combined evaluation model can effectively list the advantages of each evaluation model and improve the dependability of water quality plan, and provided a new research idea for the optimal evaluation of water pollution control plan.

Feasibility Study on Common Methods for Wave Force Estimation of Deep Water Combined Breakwaters

China's newly enacted Breakwater Design Specifications(JTS154-2011) explicitly state that breakwaters with water depths greater than 20 m are categorized as deep-water breakwaters, and emphasize that design principles, methods and construction requirements are different from those of common shallow water breakwaters. However, the specifications do not make any mention of how to choose wave force calculation methods of deep-water breakwaters. To study the feasibility of different formulae for wave force estimation of deep water combined breakwaters, the wave force calculated by the Sainflou's, Goda's, modified Goda's and specifications' methods are compared for various water depths and wave heights in this paper. The calculated results are also compared with experimental data. The total horizontal forcing and the pattern of pressure distributions are presented. Comparisons show that the wave pressure distributions by the four methods are similar, but the total horizontal forces are different. The results obtained by the Goda's method and the specified formulae are much closer to the experimental data. As for the wave force estimation for the deepwater mixed embankment foundation bed parapet, the Goda's formula is applied in the case with a water depth of less than 42 m. The Specifications method is suitable for standing waves. In the wave force estimates of breastworks, Sainflou's and the modified Gaoda's formulae are no longer applicable for the foundation bed of mixed embankment.

Application of Combined Prediction Model in Predicting Total Water Consumption in Ningxia

The gray GM( 1,1) prediction model and Logistic equation gray prediction model were established separately,and then the combined prediction model was established. Taking the water consumption in Ningxia Hui Autonomous Region from 2006 to 2012 as modeling data,the total water consumption of the whole region of Ningxia in 2018-2020 was analyzed and predicted. The results show that the accuracy of the three prediction models meets the accuracy requirements,but the gray GM( 1,1) and combined prediction models better conform to the actual situation and have better applicability.

Combined imbibition system with black nanosheet and low-salinity water for improving oil recovery in tight sandstone reservoirs

Nanomaterials and low-salinity water(LSW)are two popular enhanced oil recovery(EOR)methods that have been widely studied in recent years.The former is used for in-depth conformance improvement and the latter for microscopic oil displacement(by altering the potential and contact angle).However,there are few literature on combining them to achieve synergistic effects,especially for tight sandstone res-ervoirs.Based on the reservoir conditions of the Jimusar Oilfield,this study investigated the oil recovery mechanism of the combined imbibition system,which was composed of black nanosheet(BN)and LSW.Its performances including decreasing interfacial tension,emulsification,and wettability alterations were evaluated.The imbibition differences between the single system of BN and LSW and the combined BN-LsW imbibition system were then compared.Results showed that the combined imbibition system had a better emulsification effect on the crude oil and could also alter the wettability of the core surface.Moreover,the combined system could increase both the imbibition rate and the ultimate oil recovery.The nuclear magnetic T2 spectrum also indicated that the addition of black nanosheets could divert more fluid into small pores and thus improve the microscopic sweep efficiency.

Water, Air Emissions, and Cost Impacts of Air-Cooled Microturbines for Combined Cooling, Heating, and Power Systems： A Case Study in the Atlanta Region

The increasing pace of urbanization means that cities and global organizations are looking for ways to increase energy efficiency and reduce emissions. Combined cooling, heating, and power （CCHP） systems have the potential to improve the energy generation efficiency of a city or urban region by providing energy for heating, cooling, and electricity simultaneously. The purpose of this study is to estimate the water consumption for energy generation use, carbon dioxide （CO2） and NOx emissions, and economic impact of implementing CCHP systems for five generic building types within the Atlanta metropolitan region, under various operational scenarios following the building thermal （heating and cooling） demands. Operating the CCHP system to follow the hourly thermal demand reduces CO2 emissions for most building types both with and without net metering. The system can be economically beneficial for all building types depending on the price of natural gas, the implementation of net metering, and the cost structure assumed for the CCHP system. The greatest reduction in water consumption for energy production and NOx emissions occurs when there is net metering and when the system is operated to meet the maximum yearly thermal demand, although this scenario also results in an increase in greenhouse gas emissions and, in some cases, cost. CCHP systems are more economical for medium office, large office, and multifamilv residential buildings.

Combined refraction and diffraction models for sea waves over complicated topography and with currents in shallow water

-Combined refraction and diffraction models in the form of linear parabolic approximation are derived through smallparameter method. More strictly theoretical basis and more accuracy in the models than Lozano's (1980) are obtained. Some theoretical defects in Liu's model (1985) with consideration of current are not only found but also eliminated. More strict and accurate models are, therefore, presented in this paper.The calculation results and analysis in applying the models to actual wave field with consideration of bottom friction will be given in the following paper.

Diagnostic Method and Adaptability Analysis of Multiple Water Breakthroughs in Horizontal Well in Combined Well Pattern

The combined well pattern has been widely used in reservoir development, with a common pattern being a horizontal well in the center for oil production and multiple vertical wells around for water injection. For this type of well pattern, determining the horizontal well is affected by which injection wells, especially when the injecting water breaks through, accurately determining the direction of water inflow will provide an important basis for targeted water well measures. Based on the production performance data of horizontal wells, the semi logarithmic relationship curves of water-oil ratio, derivative water-oil ratio, and cumulative production were used for the first time to determine the breakthrough problem of water injection in the surrounding water injection wells of horizontal wells based on their response characteristics. The adaptability of this method under different influencing factors was analyzed. Introducing the parameter of cumulative production not only preserves the variation trend of the derivative of water-oil ratio with time, but also facilitates the processing of actual production data.

NONLINEAR DYNAMICS RESPONSE OF CASING PIPE UNDER COMBINED WAVE-CURRENT

The vortex-induced nonlinear vibration of casing pipes in the deep water was studied considering the loads of current and combined wave-current. The vortex-induced vibration equation of a casing pipe was set up considering the beam mode and Morison’s nonlinear fluid loads as well as the vortex-excited loads. The approach of calculating vortex-excited nonlinear vibration by Galerkin’s method was proposed. The natural vibration frequencies and modes were obtained, and the response including primary resonance induced by current and the composite resonance under combined wave-current for the 170 m long casing pipe in the 160m depth of water were investigated. The results show that the dynamics response of casing pipe obviously increases, and the complicated response behaviors of casing pipe are described under combined wave-current.

Application of high-pressure water jet technology and the theory of rock burst control in roadway

This paper puts forward using high-pressure water jet technology to control rock burst in roadway, and analyzes the theory of controlling rock burst in roadway by the weak structure zone model. The weak structure zone is formed by using high-pressure water jet to cut the coal wall in a continuous and rotational way. In order to study the influence law of weak structure zone in surrounding rock, this paper numerically analyzed the influence law of weak structure zone, and the disturbance law of coal wall and floor under dynamic and static combined load. The results show that when the distance between high-pressure water jet drillings is 3 m and the diameter of drilling is 300 mm, continuous stress superposition zone can be formed. The weak structure zone can transfer and reduce the concentrated static load in surrounding rock, and then form distressed zone. The longer the high-pressure water jet drilling is, the larger the distressed zone is. The stress change and displacement change of non-distressed zone in coal wall and floor are significantly greater than that of distressed zone under dynamic and static combined load. And it shows that the distressed zone can effectively control rock burst in roadway under dynamic and static combined load. High-pressure water jet technology was applied in the haulage gate of 250203 working face in Yanbei Coal Mine, and had gained good effect. The study conclusions provide theoretical foundation and a new guidance for controlling rock burst in roadway.

Reasonable location parameters of pick and nozzle in combined cutting system

The drum shearer and high pressure water jet combined cutting system is an effective technology to cut hard coal-rock, but one problem of the technology is the choice of pick and nozzle location parameters. In order to solve the problem, the process and mechanism of combined cutting arc studied and mining seepage catastrophe theory is used to construct the mathematic and physical model of combined cutting hard coal-rock. Based on the model and detailed analysis of combined cutting mechanism, the single pick and nozzle combined cutting test-bed is built to test the main pick and nozzle location parameters of drum shearer and water jet combined cutting system. Test results show that the best vertical distance between the pick-tip and nozzle center point is the sum of cutting thickness and proper target distance in the Y axial direction; the best horizontal distance is the length between pick-tip point and coal-rock surface bursting crack point in the X axial direction. The best incident angle of water jet should be the same as the bursting crack line＇s angle in theory, but considering other important factors comprehensively, it is more reasonable when the incident angle of water jet is 90°.

NONLINEAR DYNAMICS RESPONSE OF CASING PIPE UNDER COMBINED WAVE-CURRENT

The vortex-induced nonlinear vibration of casing pipes in the deep water was studied considering the loads of current and combined wave-current. The vortex-induced vibration equation of a casing pipe was set up considering the beam mode and Morison＇s nonlinear fluid loads as well as the vortex-excited loads. The approach of calculating vortex-excited nonlinear vibration by Galerkin＇s method was proposed. The natural vibration frequencies and modes were obtained, and the response including primary resonance induced by current and the composite resonance under combined wave-current for the 170 m long casing pipe in the 160 m depth of water were investigated. The results show that the dynamics response of casing pipe obviously increases, and the complicated response behaviors of casing pipe are described under combined wavecurrent.

Study on the optimization of the combined blown converter process in Chongqing Iron and Steel Company

The effects of lance height and bottom blown flowrate on the mixed time, the splashing amount, the penetrating depth, and the level fluctuation of an 85 t combined blown converter have been studied using a water model. The results show that the maximal stirring energy is provided to the bath at the top lance height of about 50-100 mm. When the top lance height is in the range ofg0- 110 mm, the splashing amount caused by the top jet can reach the maximal value. The appropriate operational parameters of Chongqing Iron and Steel Company （CISC） converter have been established that the top lance height is 1600-1760 mm and the bottom blowing flowrate is 240-480 Nm^3/h in the primary phase of a heat, 1100-1300 mm and 160-200 Nm^3/h in the second phase, and 1040-1120 mm and 200-350 Nm^3/h in the end phase. Also, the trial shows that the metallurgical result of the studied blow pattern is better than that of the former pattern. At the starting 3-4 min of a heat, the strong splashing is eliminated. 2008 University of Science and Technology Beijing. All rights reserved.

Improved Design of a 25 MW Gas Turbine Plant Using Combined Cycle Application

This paper presents the improved design of a 25 MW gas turbine power plant at Omoku in the Niger Delta area of Nigeria, using combined cycle application. It entails retrofitting a steam bottoming plant to the existing 25 MW gas turbine plant by incorporating a heat recovery steam generator. The focus is to improve performance as well as reduction in total emission to the environment. Direct data collection was performed from the HMI monitoring screen, log books and manufacturer’s manual. Employing the application of MATLAB, the thermodynamics equations were modeled and appropriate parameters of the various components of the steam turbine power plant were determined. The results show that the combined cycle system had a total power output of 37.9 MW, made up of 25.0 MW from the gas turbine power plant and 12.9 MW (an increase of about 51%) from the steam turbine plant, having an HRSG, condenser and feed pump capacities of 42.46 MW, 29.61 MW and 1.76 MW respectively. The condenser cooling water parameters include a mass flow of 1180.42 kg/s, inlet and outlet temperatures of 29.8°C and 35.8°C respectively. The cycle efficiency of the dry mode gas turbine was 26.6% whereas, after modification, the combined cycle power plant overall efficiency is 48.8% (about 84% increases). Hence, SIEMENS steam turbine product of MODEL: SST-150 was recommended as the steam bottoming plant. Also the work reveals that a heat flow of about 42.46 MW which was otherwise being wasted in the exhaust gas of the 25 MW gas turbine power plant could be converted to 12.9 MW of electric power, thus reducing the total emission to the environment.