Low frequency damping capacities of commercial pure magnesium

The amplitude-dependent and temperature-dependent low frequency damping capacities of magnesium with 99.96% purity were studied by a dynamic mechanical analyzer. The pure magnesium alloys include CPM1 and CPM2 castings having textures of columnar grains which extraordinarily influence the damping behaviours. The commercial pure magnesium alloy CPM was re-melted to obtain equiaxed grains, which could remove the effect of texture orientation on the damping behaviours of these pure magnesium alloys. The results of strain amplitude-dependent damping spectrums of these pure magnesium alloys show that the pure magnesium with equiaxed grains possesses the highest damping capacity. In temperature-dependent damping plot for all these three pure magnesium alloys, there are two damping peaks P1 and P2 located at 80 and 230 °C, respectively. These two damping peaks are considered to be caused by the interaction between dislocation and point defects, and the movement of grain boundaries, respectively.

Effect of strain rate on microstructural evolution and thermal stability of 1050 commercial pure aluminum

Effects of strain rate on the microstructure evolution and thermal stability of1050commercial pure aluminum processed by means of split Hopkinson pressure bar(SHPB)and Instron?3369mechanical testing machine were investigated.Samples in the deformed state and after various annealing treatments at423?523K(150?250°C)for1h were characterized by TEM and hardness test.The result reveals that the samples in the deformed state were mainly composed of elongated subgrains/cells with high density of dislocations.Microstructures of the quasi-static compressed aluminum were quite stable throughout the temperature range studied,and no significant grain growth was observed.However,for the dynamic impacted one,recrystallized grains with an average grain size of4.7μm were evolved after annealing at523K(250°C)for1h.It is suggested that the annealing behavior of this dynamic deformed aluminum is a continuous process of grain coarsening,rather than the traditional discontinuous recrystallization for the quasi-static compressed aluminum.

Surface nanocrystallization of commercial pure titanium by shot peening

The surface nanostructures of commercial pure titanium was realized by the modified shot peening equipment commonly used in industry through the special treatment process. The results show that high-energy-shot-peening(HESP) commonly used to prepare nanostructured surface layers can be achieved by the increase of pill size, pill speed, and treatment time in the commercial shot peening equipment. XRD, SEM and TEM were used to characterize the surface layer microstructure of treated specimens. The analytic results show that the main deformation mode of commercial pure Ti is twinning. At the beginning of deformation, the dislocations are formed and twins occur within or on plane, then twins in intersection plane appear, and at last the twin characteristics disappear in the surface layer after longer treatment time. The deformation layer depth increases with treatment time in a certain period when the pill size and speed are unchanged. And in the severe plastic deformation (SPD) layer in which the twins are not identified easily by using SEM, the nanocrystalline microstructures are found under TEM. The finest grain size in the surface layer is about 40 nm, and the depth of nanostructured layers is over 60 μm. The microhardness of the nanostructured surface layers is enhanced significantly after shot peening compared with that of the initial simple.

Tension-Compression Asymmetry in Ultrafine-grained Commercially Pure Ti Processed by ECAP

A homogenous microstructure of ultrafine-grained (UFG) commercially pure (CP) Ti characterized by equiaxed grains/subgrains with an average grain size of about 150 nm and strong prismatic fiber texture were obtained after 4 passes of equal channel angular pressing (ECAP).Tension–compression asymmetry in yield and work hardening behavior of UFG CP Ti were investigated by uniaxial tension and compression tests.The experimental results reveal that UFG CP Ti exhibits a relatively obvious tensioncompression asymmetry in yielding and work hardening behavior.The basal and prismaticslip are suppressed either for tension or compression,which is the easiest to activate.The tension twin system{1012}<1011> easily activated in compression deformation due to the prismatic fiber texture based on the Schmidt factor,consequently resulting in a lower yield strength under compression than tension.ECAP can improve the tension-compression asymmetry of CP Ti due to grain refinement.The interaction among the dislocations,grain boundaries and deformation twins are the main work hardening mechanisms for compression deformation,while the interaction between the dislocations and grain boundaries for tension deformation.Deformation twins lead to the higher work hardening under compression than tension.

Deformation and fracture behavior of commercially pure titanium with gradient nano-to-micron-grained surface layer

Titanium with gradient nano-to-micron scale grains from surface to matrix was fabricated by surface mechanical grinding treatment(SMGT) at room temperature.The SMGT-treated titanium shows higher strength than that of as-received one,but moderate ductility between those of ultra-fine grained(UFG) and coarse-grained titanium.Tensile stress-strain curves of SMGT-treated titanium show double strain hardening regimes.The strain hardening rate(dσ/dε) decreases with increasing strain in tensile deformation.The high strain hardening rate at initial yielding is attributed to nano-to-micron-grained surface layer.The low strain hardening rate at large plastic strain regime primarily results from coarse-grained matrix.The SMGT-treated titanium shows a ductile fracture mode with a large number of dimples.The small size of dimples in the treated surface layer is due to the combination of the high strength and strain hardening exponent.The difference between dimple size in nano-to-micron-grained surface layer and coarse-grained matrix is discussed in terms of plastic zone size at the tip of crack in the SMGT-treated titanium.

Comparison of microstructures and mechanical properties between forging and rolling processes for commercially pure titanium

In order to reveal the differences caused by forging and rolling process for titanium ingots, hot compression behavior, mechanical properties and the microstructures of forged billets and rolled ones were investigated in detail using Gleeble-1500 thermal mechanical simulator, universal testing machine and optical microscope （OM）. The compression deformation experimental data of commercially pure titanium （CP-Ti） were mapped to be a T vs lg diagram in which data fall into three distinct regions, i.e., three-stage work hardening, two-stage work hardening and flow softening, which can be separated by border lines at 17.5 and 15.4 for lg Z, where Z represents the Zener-Hollomon parameter. The deformation twin is found to have higher Z-value corresponding to the work hardening region. The differences in microstructures and mechanical properties for two kinds of billets indicate that forged billet consists of deformation twins and some twin intersections, and many twins cross the grain boundaries. However, nearly no twins can be seen in the microstructure of billet formed by rolling under optical microscope （OM）, but there are equiaxed and platelike grains. Tensile tests and Vickers hardness test indicate that yield strength, tensile strength and microhardness of the samples after forging are higher than those after rolling.

Enhanced Surface Mechanical Properties and Microstructure Evolution of Commercial Pure Titanium Under Electropulsing-Assisted Ultrasonic Surface Rolling Process

The effects of electropulsing-assisted ultrasonic surface rolling process on surface mechanical properties andmicrostructure evolution of commercial pure titanium were investigated. It was found that the surface mechanical prop-erties were significantly enhanced compared to traditional ultrasonic surface rolling process （USRP）, leading to smallersurface roughness and smoother morphology with fewer cracks and defects. Moreover, surface strengthened layer wasremarkably enhanced with deeper severe plastic deformation layer and higher surface hardness. Remarkable enhancementsof surface mechanical properties may be related to the gradient refined microstructure, the enhanced severe plasticdeformation layer and the accelerated formation of sub-boundaries and twins induced by coupling effects of USRP andelectropulsing. The primary intrinsic reasons for these improvements may be attributed to the thermal and athermal effectscaused by electropulsing treatment, which would accelerate dislocation mobility and atom diffusion.

Microstructure and textural evolution during cold rolling and annealing of commercially pure titanium sheet

The effects of cold rolling and annealing on the microstructure and textural evolution of a commercially pure titanium（CP-Ti） sheet were investigated. Electron backscatter diffractometry demonstrates that the deformation during rolling is accommodated by twinning and slip. Additionally, twinning is the dominant deformation mechanism when the cold rolling reduction is less than 40%. During rolling, {11ˉ22}11ˉ2ˉ3contraction twinning（CT） and {10ˉ12}10ˉ11 extension twinning（ET） are activated. And, the intensity of the（0002） pole along the ND gradually increases with increasing deformation. During annealing, the fraction of low angle grain boundaries（LAGBs） and the intensity of the（0002） pole along the ND gradually decrease slightly with increasing annealing time, while twinning lamellae disappear rapidly. When the annealing time reaches 60 min, 20% cold-rolled sheet recrystallizes almost completely.

Static mechanical properties and ductility of biomedical ultrafine-grained commercially pure titanium produced by ECAP process

Equal channel angular pressing(ECAP)is one of the most effective processes to produce ultra-fine grain(UFG)and nanocrystalline(NC)materials.Because the commercially pure titanium exhibits excellent biocompatibility properties,it has a significant potential to be utilized as an implant material.The low static and dynamic strengths of the pure titanium are one of the weaknesses of this material.This defect can be removed by applying the ECAP process on the pure titanium.In this work,the commercially pure titanium Grade2(CP-Ti of Grade2)was pressed at room temperature by the ECAP process via a channel angle of135°for3passes.The microstructural analysis and mechanical tests such as tensile test,hardness test,three-point bending test and Charpy impact test were all carried out on the ECAPed CP-Ti through3passes.The microstructural evolution reveals that by applying the ECAP process,coarse grain(CG)structure develops to UFG/NC structure.Moreover,the results of the mechanical tests show that the process significantly increases the yield and ultimate tensile strengths,bending strength,hardness and fracture toughness of the commercially pure titanium so that it can be used as a replacement for metallic alloys used as biomaterials.

Transformation mechanism and mechanical properties of commercially pure titanium

In order to establish the rolling process parameters of grade-2 commercially pure titanium （CP-Ti）, it is necessary to understand the transformation mechanism and mechanical properties of this material. The β→α transformation kinetics of the grade-2 CP-Ti during continuous cooling was measured and its hot compression behavior was investigated using Gleeble-1500 thermal mechanical simulator. Dynamic CCT diagram confirms that cooling rate has an obvious effect on the start and finishing transformation and microstructures at room temperature. The critical cooling rate for γ-phase transforms to a phase is about 15℃/s. When the cooling rate is higher than 15 ℃/s, some β phases with fine granular shape remain residually into plate-like structure. The plate-like a phase forms at cooling rate lower than 2 ℃/s, serrate a phase forms at medium cooling rates, about 5-15℃/s. The flow stress behavior of grade-2 CP-Ti was investigated in a temperature range of 700-900℃ and strain rate of 3.6-40 mm/min. The results show that dynamic recrystallization, dynamic recovery and work-hardening obviously occur during hot deformation. Constitutive equation of grade-2 CP-Ti was established by analyzing the relationship of the deformation temperature, strain rate, deformation degree and deformation resistance.

Effect of annealing temperature on microstructure and mechanical properties of cold-rolled commercially pure titanium sheets

The strength of traditional commercially pure titanium(CP-Ti) alloys often fails to meet the demand of structural materials. In order to enhance their mechanical properties, the cold-rolled CP-Ti alloys were annealed at different temperatures, and the recrystallization behavior and texture evolution were investigated. It was found that the bimodal microstructure(equiaxed and elongated grains) was formed after partial recrystallization, and the corresponding sample exhibited an excellent combination of ultimate tensile strength(702 MPa) and total elongation(36.4%). The recrystallization nucleation of CP-Ti sheets occurred preferentially in the high strain and the high-angle grain boundaries(HAGBs) regions. Meanwhile, the internal misorientations of the deformed heterogeneous grains increased and transformed into HAGBs, which further promoted the recrystallization nucleation. The main recrystallization texture was basal TD-split texture transformed from cold-rolled basal RD-split texture, and the oriented nucleation played a dominated role during recrystallization.

Microstructural approach to equal channel angular processing of commercially pure titanium——A review

A review on severe plastic deformation（SPD） technique of equal channel angular pressing（ECAP） process of commercially pure titanium（CP-Ti） alloys was presented with a major emphasize on the influence of ECAP parameters that include channel and curvature angles, processing route, temperature of operation, pressing speed, internal heating, number of pass through the die and back pressure. Various ECAP characteristics such as microstructure, strain inhomogeneity and mechanical properties are considered to achieve the maximum homogeneity, equilibrium grain refinement and mechanical improvement of CP-Ti. Investigations show that a pressing speed of 1-3 mm/s at 450 °C with route BC along with channel and curvature angles of 90° and 20° respectively with backpressure can lead to the most homogeneous ultrafine microstructure.

Effect of electropulsing on anisotropy behaviour of cold-rolled commercially pure titanium sheet

The specimens cut from the cold-rolled pure titanium sheet at 0°,45°and 90°to the rolling direction were treated by high density electropulsing(maximum current density J=(7.22-7.96)×10^(3)A/mm^(2),pulse period t_(p)=110μs).The mechanical properties and microstructures of the cold-rolled,electropulsed and conventional annealed commercially pure titanium sheet were examined by using uniaxial tension test machine and optical microscope(OM),respectively.The results show that the deformation behavior of the electropulsed pure titanium sheet is significantly different from that of conventional annealed pure titanium sheet.The difference of the mechanical properties between the 0°,45°and 90°direction specimens is almost diminished.It is mainly due to the increase in dislocation mobility and formation of lamellar microstructure after the electropulsing.

Improving the solidification structure of commercially pure aluminium with electropulse acting on liquid metal

The effect of electropulse on the solidification structure of commercially pure aluminium was studied. The orthogonal array L9 was used to determine the effect of three process parameters of electropulse modification （EPM）, which were pulse current intensity, pulse frequency, and treating time. For each factor, three levels were chosen to cover the experimental region. According to the experimental results, the solidification structure of commercially pure aluminium was modified from large grains with columnar crystals to finer grains with equiaxed crystals, by allowing the electropulse to act on liquid aluminium. However, the solidification structures could be refined differently at different EPM parameters. Certain EPM parameters should be selected to get the optimum solidification structure. Among the three parameters, pulse frequency was the most important factor influencing the solidification structure, the secondary factor was current intensity, and treating time was the third one. The optimum parameters were the pulse frequency of 5 Hz, the current intensity of 68 A, and the treating time of l0 s.

Planar anisotropy of commercially pure titanium sheets

Commercially pure titanium （CP Ti） sheets show typical planar anisotropy due to the inherently crys- tallographic texture and manufacturing process. To char- acterize the planar anisotropic behaviors of CP Ti sheets in the forming process, uniaxial tensile tests of TA0 sheets were performed along rolling, transverse, and diagonal directions at room temperature; corresponding stress-strain curves and Lankford coefficients were obtained. Based on Hi11＇48 and Barlat＇89 yield functions, the planar anisotropy of TA0 sheets was investigated. In order to verify the accuracy of two models, we compared the experimental and predicted values of yield stress and Lankford coeffi- cients. It reveals that Barlat＇89 criterion with M = 10 is good agreement with experimental data, and the obtained function can be used in simulation of forming process.

Mechanical Property Prediction of Commercially Pure Titanium Welds with Artificial Neural Network

Factors that affect weld mechanical properties of commercially pure titanium have been investigated using artificial neural networks. Input data were obtained from mechanical testing of single-pass, autogenous welds, and neural network models were used to predict the ultimate tensile strength, yield strength, elongation, reduction of area, Vickers hardness and Rockwell B hardness. The results show that both oxygen and nitrogen have the most significant effects on the strength while hydrogen has the least effect over the range investigated. Predictions of the mechanical properties are shown and agree well with those obtained using the 'oxygen equivalent' (OE) equations.

Surface modifications of biometallic commercially pure Ti and Ti–13Nb–13Zr alloy by picosecond Nd:YAG laser

The effects of picosecond Nd:YAG laser irradiation on chemical and morphological surface characteristics of the commercially pure titanium and Ti–13Nb–13Zr alloy in air and argon atmospheres were studied under different laser output energy values.During the interaction of laser irradiation with the investigated materials,a part of the energy was absorbed on the target surface,influencing surface modifications.Laser beam interaction with the target surface resulted in various morphological alterations,resulting in crater formation and the presence of microcracks and hydrodynamic structures.Moreover,different chemical changes were induced on the target materials’surfaces,resulting in the titanium oxide formation in the irradiation-affected area and consequently increasing the irradiation energy absorption.Given the high energy absorption at the site of interaction,the dimensions of the surface damaged area increased.Consequently,surface roughness increased.The appearance of surface oxides also led to the increased material hardness in the surface-modified area.Observed chemical and morphological changes were pronounced after laser irradiation of the Ti–13Nb–13Zr alloy surface.

The Evolution of Hardness Homogeneity in Commercially Pure Ti Processed by ECAP

The evolution of hardness homogeneity in commercially pure titanium processed by equal channel angular pressing （ECAP） for up to 4 passes following route C at room temperature using a die of 90° was investigated by recording the microhardness on the cross-sectional and longitudinal planes of each billet. The results show that the hardness increases significantly after the first pass although there is a region of lower hardness on the cross-section running in a band near the bottom surface of the billet, and then increases by very small amounts in subsequent passes. With increasing numbers of passes, the lower hardness region near the bottom surface disappears and the microhardness values are distributed homogeneously throughout the cross- sectional and longitudinal planes after 4 passes of ECAP. The microhardness values in the central regions of the billet are slightly lower than those of the top and bottom surfaces. The results show that good homogeneity may be achieved throughout the billets after 4 passes of ECAP following route C.

Cell Attachment of Periodontal Ligament Cells on Commercially Pure Titanium at the Early Stage

Summary: In order to study the character of periodontal ligament cells (PDLCs) attaching on commercially pure titanium (cpTi) by morphology and metrology on the early stage (24 h), 1×105/ml PDLCs in 2 ml culture medium were seeded on cpTi discs fixed in 24-well culture plates. Morphology of cell attachment was observed by contrast phase microscope, scanning electron microscope (SEM) and fluroscence microscopy. Cell adhesion was analyzed by MTT at 0.5, 1, 2, 4 h respectively. PDLCs could attach and spread on cpTi discs. SEM showed that PDLCs had pseudopod-like protuberance. PDLCs showed different attaching phases and reached saturation in cell number at 2 h. It was concluded that PDLCs had good biocompatibility with cpTi, and showed a regular and dynamic pattern in the process of attaching to cpTi.

Improvement of Surface Mechanical and Tribological Characteristics of L-PBF Processed Commercially Pure Titanium through Ultrasonic Impact Treatment

Multi-pass ultrasonic impact treatment(UIT)was applied to modify the microstructure and improve the mechanical and tribological characteristics at the near-surface region of commercially pure Ti(CP-Ti)specimens produced by the laser powder bed fusion(L-PBF)method.UIT considerably refined the L-PBF process-related acicular martensites(α′-M)and produced a well-homogenized and dense surface microstructure,where the porosity content of 1-,3-,and 5-pass UITed samples was reduced by 43,60,and 67%,respectively.The UITed samples showed an enhancement in their near-surface mechanical properties up to a depth of about 300μm.The nanoindentation results for the 3-pass UITed sample revealed an increase of about 53,45,and 220%in its nanohardness,H/E_(r),and H_(3)/E_(r)^(2)indices,respectively.The stylus profilometry results showed that performing the UIT removed the L-PBF-related features/defects and offered a smooth surface.The roughness average(R_(a))and the skewness(R_(sk))of the 3-pass UITed sample were found to be lower than those of the L-PBFed sample by 95 and 223%,respectively.Applying the UIT also enhanced the material ratio,where the maximum load-bearing capacity(~100%)in as-L-PBFed(as-built)and 3-pass UITed samples was obtained at 60-and 10-µm depths,respectively.The tribological investigations showed that applying the UIT resulted in a significant reduction of wear rate and average coefficient of friction(COF)of CP-Ti.For instance,under the normal pressures of 0.05 and 0.2 MPa,the wear rate and COF of the 3-pass UITed sample were lower than those of the L-PBFed sample by 65 and 58%,and 20 and 17%,respectively.