A Rapid Method for Compensating Output Error of Electromagnetic Tracker

Some methods which use an optical tracker(OT) as a standard reference of electromagnetic tracker(EMT) were proposed in order to compensate the output error of electromagnetic tracker. Usually,they use a magneto-optic tool to collect the outputs of OT and EMT simultaneously,and then compare the output of OT with that of EMT to compensate the error of EMT. Although the outputs of EMT and OT can be matched each other by using a time stamp which denotes when the acquirement command is sent,but the accuracy will decrease if the tool moves faster for the errors of the time stamp itself. A rapid method for compensating EMT output error is proposed. A particular scan mode of the magneto-optic tool is designed for collecting EMT and OT outputs,and a data registration method is proposed to match the outputs of EMT and OT. The simulated results show that the output error of EMT can be decreased efficiently and the accuracy of the compensation can be improved by about 15% compared with that of the existing methods.

Active Error Compensating Welding Fixture System for Auto Body

The welding fixtures are the most important devices for an auto body welding assembly line. The current special fixtures used by many automotive manufactures are only fit for one or several specific welding processes, and the dimensional problem in the circle due to several variation sources accumulation has no adjustment. The active error compensating welding fixture system for auto body is designed and manufactured. The detecting model, coordinate transformation model, and adjusting model based on auto body coordinate system are presented. The dowel pin modular design is adopted in the structure of the fixture to suit different workpieces with some similar characteristics. The online detection and adaptive control system using eddy current sensors and adaptive adjusting devices is analyzed. Three kinds of the left rear wheel covers SGM60 are selected to test workpieces of the developed system, and the active error compensating experiments are performed in the lab for many times. Test results show the validity of mechanism reconfigurations, on-line detections and error compensations of the developed welding fixture.

Research on dynamic error compensation for an armored K type thermocouple

A new method was proposed, in which a high-power CO2 laser modulated by high frequency was used as the driv- ing source to heat up a surface-temperature sensor. The continual beam and the pulsed beam sent out by the same laser could be used in the same system to carry on the static calibration of the radiation thermometer and the dynamic calibration of the temperature sensor to be checked. The frequency-response characteristics of high-speed radiation thermometer surpassed that of the temperature sensor, therefore it could be used as the reference value to calibrate the latter and let system error be cor- rected. Differences in the environment of the sensor installing and the error caused by the change of thermo-physical proper- ty could be avoided. Thus, the difficult problem of traceable dynamic calibration of temperature was solved. In experiment, to obtain the frequency characteristics of the thermocouple and the dynamic performance of the K type thermocouple, which could compensate the dynamic characteristics of the sensor, the sensor was dynamically corrected by using the method, and then the mathematical model was established.

Research on the Dynamic Model of Spindle Rotation Induced Error Compensation System of Boring and its Simulation

In this paper we address the dynamics of compensation cutting process from both Laplace s frequency domain and the time domain of the first time, using the two computer aided analyzing softwares: MATLAB and SIMULINK. Theoretical analysis and simulation experiments firstly show that not only the systematical stiffness of workpiece, spindle and tools, but also the regenerated coefficient affects the compensation displacement effect. The results show that the SREC is practicable in reality to decease the spindle induced errors in many engineering applications such as hard boring through simulation and the preliminary experiment results.

MODELING AND COMPENSATION TECHNIQUE FOR THE GEOMETRIC ERRORS OF FIVE-AXIS CNC MACHINE TOOLS

One of the important trends in precision machining is the development ofreal-time error compensation technique. The error compensation for multi-axis CNC machine tools isvery difficult and attractive. The modeling for the geometric error of five-axis CNC machine toolsbased on multi-body systems is proposed. And the key technique of the compensation―identifyinggeometric error parameters―is developed. The simulation of cutting workpiece to verify the modelingbased on the multi-body systems is also considered.

Error Compensation of Thin Plate-shape Part with Prebending Method in Face Milling

Low weight and good toughness thin plate parts are widely used in modem industry, but its flexibility seriously impacts the machinability. Plenty of studies locus on the influence of machine tool and cutting tool on the machining errors. However, few researches focus on compensating machining errors through the fixture. In order to improve the machining accuracy of thin plate-shape part in face milling, this paper presents a novel method for compensating the surfacc errors by prebending the workpiece during the milling process. First, a machining error prediction model using finite element method is formulated, which simplifies the contacts between the workpiece and fixture with spring constraints. Milling fbrces calculated by the micro-unit cutting force model arc loaded on the error prediction model to predict the machining error. The error prediction results are substituted into the given formulas to obtain the prebending clamping forces and clamping positions. Consequently, the workpiece is prebent in terms of the calculated clamping forces and positions during the face milling operation to reduce the machining error. Finally, simulation and experimental tests are carried out to validate the correctness and efficiency of the proposed error compensation method. The experimental measured flatness results show that the flatness improves by approximately 30 percent through this error compensation method. The proposed mcthod not only predicts the machining errors in face milling thin plate-shape parts but also reduces the machining errors by taking full advantage of the workpiece prebending caused by fixture, meanwhile, it provides a novel idea and theoretical basis for reducing milling errors and improving the milling accuracy.

Periodic Error Compensation for Quartz MEMS Gyroscope Drift of INS

In order to improve the navigation accuracy of an inertial navigation system （INS）, composed of quartz gyroscopes, the existing real-time compensation methods for periodic errors in quartz gyroscope drift and the periodic error term relationship between sampled original data and smoothed data are reviewed. On the base of the results, a new compensation method called using former period characteristics to compensate latter smoothness data （UFCL for short） method is proposed considering the INS working characteristics. This new method uses the original data without smoothing to work out an error conversion formula at the INS initial alignment time and then compensate the smoothed data errors by way of the formula at the navigation time. Both theoretical analysis and experimental results demonstrate that this method is able to cut down on computational time and raise the accuracy which makes it a better real-time compensation approach for periodic error terms of quartz micro electronic mechanical system （MEMS） gyroscope＇s zero drift.

Modeling and Compensation Technology for the Comprehensive Errors of Fixture System

Error modelling and compensating technology is an effective method to improve the processing precision.The position and orientation deviation of workpiece is caused by the fixing and manufacturing errors of the fixture.How to reduce the position and orientation deviation of workpiece has become a technical problem of improving the processing quality of workpiece.In order to increase machining accuracy,an implementation scheme of fixture system comprehensive errors（FSCE） compensation is proposed.A FSCE parameter model is established by analyzing the influence of contact points on the position and orientation of workpiece.Meanwhile,a parameter identification method for FSCE parameter model is presented by using the 3-2-1 deterministic positioning fixture,which determines the model parameters.Moreover,a FSCE compensation model is formulated to study the compensation value of the cutting position.By using RenishawOMP60 Probe and combining vertical machining centre（SKVH850） equipment with SKY2001 Open CNC System,on-machine verification system（OMVS） is built to measure FSCE successfully.The processing error can be reduced by analyzing the cutting position of the tool with the homogeneous transformation of space coordinate system.Finally,the compensation experiment of real time errors is conducted,and the cylindricality and perpendicularity errors of hole surface are reduced by 30.77% and 28.57%,respectively.This paper provides a new way of realizing the compensation of FCSE,which can improve the machining accuracy of workpiece largely.

Motion Error Compensation of Multi-legged Walking Robots

Existing errors in the structure and kinematic parameters of multi-legged walking robots,the motion trajectory of robot will diverge from the ideal sports requirements in movement.Since the existing error compensation is usually used for control compensation of manipulator arm,the error compensation of multi-legged robots has seldom been explored.In order to reduce the kinematic error of robots,a motion error compensation method based on the feedforward for multi-legged mobile robots is proposed to improve motion precision of a mobile robot.The locus error of a robot body is measured,when robot moves along a given track.Error of driven joint variables is obtained by error calculation model in terms of the locus error of robot body.Error value is used to compensate driven joint variables and modify control model of robot,which can drive the robots following control model modified.The model of the relation between robot＇s locus errors and kinematic variables errors is set up to achieve the kinematic error compensation.On the basis of the inverse kinematics of a multi-legged walking robot,the relation between error of the motion trajectory and driven joint variables of robots is discussed.Moreover,the equation set is obtained,which expresses relation among error of driven joint variables,structure parameters and error of robot＇s locus.Take MiniQuad as an example,when the robot MiniQuad moves following beeline tread,motion error compensation is studied.The actual locus errors of the robot body are measured before and after compensation in the test.According to the test,variations of the actual coordinate value of the robot centroid in x-direction and z-direction are reduced more than one time.The kinematic errors of robot body are reduced effectively by the use of the motion error compensation method based on the feedforward.

Kinematic Calibration and Forecast Error Compensation of a 2-DOF Planar Parallel Manipulator

Due to large workspace,heavy-duty and over-constrained mechanism,a small deformation is caused and the precision of the 2-DOF planar parallel manipulator is affected.The kinematic calibration cannot compensate the end-effector errors caused by the small deformation.This paper presents a method combined step kinematic calibration and linear forecast real-time error compensation in order to enhance the precision of a two degree-of-freedom(DOF) planar parallel manipulator of a hybrid machine tool.In the step kinematic calibration phase of the method,the end-effector errors caused by the errors of major constant geometrical parameters is compensated.The step kinematic calibration is based on the minimal linear combinations(MLCs) of the error parameters.All simple and feasible measurements in practice are given,and identification analysis of the set of the MLCs for each measurement is carried out.According to identification analysis results,both measurement costs and observability are considered,and a step calibration including step measurement,step identification and step error compensation is determined.The linear forecast real-time error compensation is used to compensate the end-effector errors caused by other parameters after the step kinematic calibration.Taking the advantages of the step kinematic calibration and the linear forecast real-time error compensation,a method for improving the precision of the 2-DOF planar parallel manipulator is developed.Experiment results show that the proposed method is robust and effective,so that the position errors are kept to the same order of the measurement noise.The presented method is attractive for the 2-DOF planar parallel manipulator and can be also applied to other parallel manipulators with fewer than six DOFs.

QFT control based on zero phase error compensation for flight simulator

To improve the robustness of high-precision servo systems, quantitative feedback theory （QFT） which aims to achieve a desired robust design over a specified region of plant uncertainty is proposed. The robust design problem can be solved using QFT but it fails to guarantee a high precision tracking. This problem is solved by a robust digital QFT control scheme based on zero phase error （ZPE） feed forward compensation. This scheme consists of two parts： a QFT controller in the closed-loop system and a ZPE feed-forward compensator. Digital QFT controller is designed to overcome the uncertainties in the system. Digital ZPE feed forward controller is used to improve the tracking precision. Simulation and real-time examples for flight simulator servo system indicate that this control scheme can guarantee both high robust performance and high position tracking precision.

Self-calibration and Compensation of Setting Errors for Surface Profile Measurement of a Microstructured Roll Workpiece

Microstructured roll workpieces have been widely used as functional components in the precision industries. Current researches on quality control have focused on surface profile measurement of microstructured roll workpieces, and types of measurement systems and measurement methods have been developed. However, low measurement efficiency and low measurement accuracy caused by setting errors are the common disadvantages for surface profile measurement of microstructured roll workpieces. In order to shorten the measurement time and enhance the measurement accuracy, a method for self-calibration and compensation of setting errors is proposed for surface profile measurement of microstructured roll workpieces. A measurement system is constructed for the measurement, in which a precision spindle is employed to rotate the roll workpiece and an air-bearing displacement sensor with a micro-stylus probe is employed to scan the microstructured surface of the roll workpiece. The resolution of the displacement sensor is 0.14 nm and that of the rotary encoder of the spindle was 0.15r~. Geometrical and mathematical models are established for analyzing the influences of the setting errors of the roll workpiece and the displacement sensor with respect to the axis of the spindle, including the eccentric error of the roll workpiece, the offset error of the sensor axis and the zero point error of the sensor output. Measurement experiments are carded out on a roll workpiece on which periodic microstructures are a period of 133 i^m along the circumferential direction. Experimental results demonstrate the feasibility of the self-compensation method. The proposed method can be used to detect and compensate the setting errors without using any additional accurate artifact.

Thermal Error Compensation for Telescopic Spindle of CNC Machine Tool Based on SIEMENS 840D System

In this paper, eddy current sensors and thermocouple sensors were employed to measure the thermal field and thermal deformation of a spindle of a telescopic CNC boring-milling machine tool, respectively. A linear regression method was proposed to establish the thermal error model. Furthermore, two compensation methods were implemented based on the SIEMENS 840D system by using the feed shaft of z direction and telescopic spindle respectively. Experimental results showed that the thermal error could be reduced by 73.79% when using the second compensation method, and the thermal error could be eliminated by using the two compensation methods effectively.

ROBOT'S MOTION ERROR AND ONLINE COMPENSATION BASED ON FORCE SENSOR

Robot＇s dynamic motion error and on-line compensation based on multi-axis force sensor are dealt with.It is revealed that the reasons of the error are formed and the relations of the error are delivered.A motion equation of robot＇s termination with the error is established,and then,an error matrix and an error compensation matrix of the motion equation are also defined.An on-line error＇s compensation method is put forward to decrease the displacement error,which is a degree of millimeter,shown by the result of simulation of PUMA562 robot.

Modeling Approach of Regression Orthogonal Experiment Design for Thermal Error Compensation of CNC Turning Center

The thermal induced errors can account for as much as 70% of the dimensional errors on a workpiece. Accurate modeling of errors is an essential part of error compensation. Base on analyzing the existing approaches of the thermal error modeling for machine tools, a new approach of regression orthogonal design is proposed, which combines the statistic theory with machine structures, surrounding condition, engineering judgements, and experience in modeling. A whole computation and analysis procedure is given. Therefore, the model got from this method are more robust and practical than those got from the present method that depends on the modeling data completely. At last more than 100 applications of CNC turning center with only one thermal error model are given. The cutting diameter variation reduces from more than 35 μm to about 12 μm with the orthogonal regression modeling and compensation of thermal error.

Prediction of diameter errors compensation in bars turning

On the basis of analyzing the machine-workpiece-tool system, the main factors affecting diameter errors in bars turning are considered, and the mathematic models of the actual workpiece diameter at the cutting point are established according to the three usual methods of mounting workpieces on a turning machine. Further a prediction system for diameter errors is developed; a new method, called discrete nodes output, is presented and applied to expressing workpiece diameter errors at given points along the part axis, then off-line compensation is implemented according to the prediction values to diminish machining errors. The results indicate that the method can diminish diameter errors more than 70%, greatly improve the machining accuracy of bars.

A convenient look-up-table based method for the compensation of non-linear error in digital fringe projection

Although the structured light system that uses digital fringe projection has been widely implemented in three-dimensional surface profile measurement, the measurement system is susceptible to non-linear error. In this work, we propose a convenient look-up-table-based （LUT-based） method to compensate for the non-linear error in captured fringe patterns. Without extra calibration, this LUT-based method completely utilizes the captured fringe pattern by recording the full-field differences. Then, a phase compensation map is established to revise the measured phase. Experimental results demonstrate that this method works effectively.

Non-Exchangeable Error Compensation for Strapdown Inertial Navigation System in High Dynamic Environment

Strapdown non-exchangeable error compensation technology in high dynamic environment is one of the key technologies of strapdown inertial navigation system.Mathematical platform is used in strapdown inertial navigation system instead of physical platform in traditional platform inertial navigation system,which improves reliability and reduces cost and volume of system.The maximum error source of attitude matrix solution is the non-exchangeable error of rotation due to the non-exchangeable of finite rotation of rigid bodies.The rotation non-exchangeable error reaches the maximum in coning motion,although it can be reduced by shortening the correction period and increasing the real-time calculation.The equivalent rotation vector method is used to modify the attitude to reduce the coning error in this paper.Simulation experiments show that the equivalent rotation vector method can effectively suppress the non-exchangeable error and improve the accuracy of attitude calculation.

Modeling, identification and compensation for geometric errors of laser annealing table

In order to improve the process precision of an XY laser annealing table, a geometric error modeling, and an identification and compensation method were proposed. Based on multi-body system theory, a geometric error model for the laser annealing table was established. It supports the identification of 7 geometric errors affecting the annealing accuracy. An original identification method was presented to recognize these geometric errors. Positioning errors of 5 lines in the workspace were measured by a laser interferometer, and the 7 geometric errors were identified by the proposed algorithm. Finally, a software-based error compensation method was adopted, and a compensation mechanism was developed in a postprocessor based on LabVIEW. The identified geometric errors can be compensated by converting ideal NC codes to actual NC codes. A validation experiment has been conducted on the laser annealing table, and the results indicate that positioning errors of two validation lines decreased from ±37 μm and ±33 μm to ±5 μm and ±4.5 μm, respectively. The geometric error modeling, identification and compensation method presented in this work can be straightforwardly extended to any configurations of 2-dimensional worktable.

Technical Research for Detector of Grain Moisture Content Based on Error Compensation

According to the existing method including testing the frequency and establishing the relationship between moisture content and frequency, a corresponding instrument was designed. In order to further improve the accuracy and rapidity of the system, a new approach to describe the relationship between the measurement error and the temperature was proposed. The error band could be obtained and divided into several parts（based on the range of temperature） to indicate the error value that should compensate the grain moisture content for the changes in temperature. By calculating the error band at the maximum and the minimum operating temperatures, as well as by determining the error compensation value from the error band based on the measurement moisture content, the final effective result was derived.