Feedback linearization and equivalent-disturbance compensation control strategy for piezoelectric stage

Piezoelectric stages use piezoelectric actuators and flexure hinges as driving and amplifying mechanisms,respectively.These systems have high positioning accuracy and high-frequency responses,and they are widely used in various precision/ultra-precision positioning fields.However,the main challenge with these devices is the inherent hysteresis nonlinearity of piezoelectric actuators,which seriously affects the tracking accuracy of a piezoelectric stage.Inspired by this challenge,in this work,we developed a Hammerstein model to describe the hysteresis nonlinearity of a piezoelectric stage.In particular,in our proposed scheme,a feedback-linearization algorithm is used to eliminate the static hysteresis nonlinearity.In addition,a composite controller based on equivalent-disturbance compensation was designed to counteract model uncertainties and external disturbances.An analysis of the stability of a closed-loop system based on this feedback-linearization algorithm and composite controller was performed,and this was followed by extensive comparative experiments using a piezoelectric stage developed in the laboratory.The experimental results confirmed that the feedback-linearization algorithm and the composite controller offer improved linearization and trajectory-tracking performance.

Case study on the mechanics of NPR anchor cable compensation for large deformation tunnel in soft rock in the Transverse Mountain area,China

A study was conducted to analyze the deformation mechanism of strongly weathered quartz schist in the Daliangshan Tunnel,located in the western Transverse Mountain area.A large deformation problem was experienced during the tunnel construction.To mitigate this problem,a support system was designed incorporating negative Poisson ratio(NPR)anchor cables with negative Poisson ratio effect.Physical model experiments,field experiments,and numerical simulation experiments were conducted to investigate the compensation mechanical behavior of NPR anchor cables.The large deformations of soft rocks in the Daliangshan Tunnel are caused by a high ground stress,a high degree of joint fracture development,and a high degree of surrounding rock fragmentation.A compensation mechanics support system combining long and short NPR anchor cables was suggested to provide sufficient counter-support force(approximately 350 kN)for the surrounding rock inside the tunnel.Comparing the NPR anchor cable support system with the original support system used in the Daliangshan tunnel showed that an NPR anchor cable support system,combining cables of 6.3 m and 10.3 m in length,effectively prevented convergence of surrounding rock deformation,and the integrated settlement convergence value remained below 300 mm.This study provides an effective scientific basis for resolving large deformation problems in deeply buried soft rocks in western transverse mountain areas.

Ultrahigh spatiotemporal resolution beam signal reconstruction with bunch phase compensation

Various electromagnetic signals are excited by the beam in the acceleration and beam-diagnostic elements of a particle accelerator.It is important to obtain time-domain waveforms of these signals with high temporal resolution for research,such as the study of beam–cavity interactions and bunch-by-bunch parameter measurements.Therefore,a signal reconstruction algorithm with ultrahigh spatiotemporal resolution and bunch phase compensation based on equivalent sampling is proposed in this paper.Compared with traditional equivalent sampling,the use of phase compensation and setting the bunch signal zero-crossing point as the time reference can construct a more accurate reconstructed signal.The basic principles of the method,simulation,and experimental comparison are also introduced.Based on the beam test platform of the Shanghai Synchrotron Radiation Facility(SSRF)and the method of experimental verification,the factors that affect the reconstructed signal quality are analyzed and discussed,including the depth of the sampled data,quantization noise of analog-to-digital converter,beam transverse oscillation,and longitudinal oscillation.The results of the beam experiments show that under the user operation conditions of the SSRF,a beam excitation signal with an amplitude uncertainty of 2%can be reconstructed.

Excavation compensation and bolt support for a deep mine drift

To overcome large deformation of deep phosphate rock roadways and pillar damage,a new type of constant-resistance large-deformation negative Poisson’s ratio(NPR)bolt that can withstand a high prestress of at least 130 KN was developed.In the conducted tests,the amount of deformation was 200-2000 mm,the breaking force reached 350 KN,and a high constant-resistance pre-stress was maintained during the deformation process.A stress compensation theory of phosphate rock excavation based on NPR bolts is proposed together with a balance system for bolt compensation of the time-space effect and high NPR pre-stress.Traditional split-set rock bolts are unable to maintain the stability of roadway roofs and pillars.To verify the support effect of the proposed bolt,field tests were conducted using both the proposed NPR bolts and split-set rock bolts as support systems on the same mining face.In addition,the stress compensation mechanism of roadway mining was simulated using the particle flow code in three dimensions(PFC^(3D))-fast Lagrangian analysis of continua(FLAC^(3D))particle-flow coupling numerical model.On-site monitoring and numerical simulations showed that the NPR excavation compensation support scheme effectively improves the stress state of the bolts and reduces the deformation of the surrounding rock.Compared to the original support scheme,the final deformation of the surrounding rock was reduced by approximately 70%.These results significantly contribute to domestic and foreign research on phosphate-rock NPR compensation support technology,theoretical systems,and engineering practices,and further promote technological innovation in the phosphate rock mining industry.

Study on thermal decomposition kinetics of azobenzene-4,4′-dicarboxylic acid by using compensation parameter method and nonlinear fitting evaluation

Recently,azobenzene-4,4'-dicarboxylic acid(ADCA)has been produced gradually for use as an organic synthesis or pharmaceutical intermediate due to its eminent performance.With large quantities put into application in the future,the thermal stability of this substance during storage,transportation,and use will become quite important.Thus,in this work,the thermal decomposition behavior,thermal decomposition kinetics,and thermal hazard of ADCA were investigated.Experiments were conducted by using a SENSYS evo DSC device.A combination of differential iso-conversion method,compensation parameter method,and nonlinear fitting evaluation were also used to analyze thermal kinetics and mechanism of ADCA decomposition.The results show that when conversion rate α increases,the activation energies of ADCA's first and main decomposition peaks fall.The amount of heat released during decomposition varies between 182.46 and 231.16 J·g^(-1).The proposed kinetic equation is based on the Avrami-Erofeev model,which is consistent with the decomposition progress.Applying the Frank-Kamenetskii model,a calculated self-accelerating decomposition temperature of 287.0℃is obtained.

Research on Anti-Fluctuation Control of Winding Tension System Based on Feedforward Compensation

In the fiber winding process,strong disturbance,uncertainty,strong coupling,and fiber friction complicate the winding constant tension control.In order to effectively reduce the influence of these problems on the tension output,this paper proposed a tension fluctuation rejection strategy based on feedforward compensation.In addition to the bias harmonic curve of the unknown state,the tension fluctuation also contains the influence of bounded noise.A tension fluctuation observer(TFO)is designed to cancel the uncertain periodic signal,in which the frequency generator is used to estimate the critical parameter information.Then,the fluctuation signal is reconstructed by a third-order auxiliary filter.The estimated signal feedforward compensates for the actual tension fluctuation.Furthermore,a time-varying parameters fractional-order PID controller(TPFOPID)is realized to attenuate the bounded noise in the fluctuation.Finally,TPFOPID is enhanced by TFO and applied to control a tension control system considering multi-source disturbances.The stability of the method is analyzed by using the Lyapunov theorem.Finally,numerical simulations verify that the proposed scheme improves the tracking ability and robustness of the system in response to tension fluctuations.

Force Compensation Control for Electro-Hydraulic Servo System with Pump-Valve Compound Drive via QFT-DTOC

Each joint of a hydraulic-driven legged robot adopts a highly integrated hydraulic drive unit(HDU),which features a high power-weight ratio.However,most HDUs are throttling-valve-controlled cylinder systems,which exhibit high energy losses.By contrast,pump control systems offer a high efficiency.Nevertheless,their response ability is unsatisfactory.To fully utilize the advantages of pump and valve control systems,in this study,a new type of pump-valve compound drive system(PCDS)is designed,which can not only effectively reduce the energy loss,but can also ensure the response speed and response accuracy of the HDUs in robot joints to satisfy the performance requirements of robots.Herein,considering the force control requirements of energy conservation,high precision,and fast response of the robot joint HDU,a nonlinear mathematical model of the PCDS force control system is first introduced.In addition,pressure-flow nonlinearity,friction nonlinearity,load complexity and variability,and other factors affecting the system are considered,and a novel force control method based on quantitative feedback theory(QFT)and a disturbance torque observer(DTO)is designed,which is denoted as QFT-DTOC herein.This method improves the control accuracy and robustness of the force control system,reduces the effect of the disturbance torque on the control performance of the servo motor,and improves the overall force control performance of the system.Finally,experimental verification is performed using the PCDS performance test platform.The experimental results and quantitative data show that the QFT-DTOC proposed herein can significantly improve the force control performance of the PCDS.The relevant force control method can be used as a bottom-control method for the hydraulic servo system to provide a foundation for implementing the top-level trajectory planning of the robot.

The Rights to Claim for Industrial Injury Compensation and Tort Compensation are Applicable to the Law:Taking Fu and Li v.a Passenger Transport Company as an Example

In the case of third-party tort,due to the lack of clear and detailed provisions on the treatment of employee’s industrial injury insurance payment and tort damage compensation,the judicial theory and practice have brought many disputes.Through combing the current relevant laws and regulations,it can be found that the application of the two systems will lead to the overlapping of industrial injury compensation.This paper analyzes the problems arising from the concurrence of industrial injury compensation and tort compensation using the case of Fu and Li v.a passenger transport company,and puts forward some ideas and suggestions on how to improve the settlement measures of such cases.

Problems and Countermeasures to Improve Clinical Trial Participants’Compensation Rights in China

Objective To discuss the problems existing in the compensation of Chinese clinical trial participants and propose some suggestions for improving their rights.Methods The literature related to the participants’right to compensation at home and abroad was searched to study the inadequacy of the compensation right for clinical trial participants in China from four aspects:insurance system,principle of attribution,legal relationship and compensation regulations.Then,some suggestions to improve the participants’right to compensation were proposed.Results and Conclusion China lacks clear legal norms for participants’right to compensation.There are problems such as unclear insurance rules and compensation rules,unclear contractual relationships between parties to clinical trials,and no laws and regulations to rely on for attribution and compensation.China should issue regulatory guidelines related to the right to compensation of participants in clinical trials,so that all parties in clinical trials can have rules to follow if there is the occurrence of injury,which can better protect the rights and interests of the participants.

The Translation of Chinese Literature under the Theory of Translation Compensation

In order to promote the exchange of Chinese culture with foreign countries,translators bear an important mission in the process of cross-cultural communication.Although there are cultural differences,we can achieve cultural dissemination and exchange through continuous cultural dialogue.As an important way for foreign scholars to understand the history of the Shang and Zhou Dynasties in China,the translation of historical texts is crucial.Multiple typical cases are selected under the guidance of the translation theory of compensation to use relevant methods or techniques from the three levels of language,culture,and aesthetics to compensate for the loss of Li Xueqin’s The Origin of Ancient Chinese Civilization in English translation proofreading.

Design of Cold-Junction Compensation and Disconnection Detection Circuits of Various Thermocouples and Implementation of Multi-Channel Interfaces Using Them-A Secondary Publication

Cold-junction compensation(CJC)and disconnection detection circuit design of various thermocouples(TC)and multi-channel TC interface circuits were designed.The CJC and disconnection detection circuit consists of a CJC semiconductor device,an instrumentation amplifier(IA),two resistors,and a diode for disconnection detection.Based on the basic circuit,a multi-channel interface circuit was also implemented.The CJC was implemented using compensation semiconductor and IA,and disconnection detection was detected by using two resistors and a diode so that IA input voltage became-0.42 V.As a result of the experiment using R-type TC,the error of the designed circuit was reduced from 0.14 mV to 3μV after CJC in the temperature range of 0°C to 1400°C.In addition,it was confirmed that the output voltage of IA was saturated from 88 mV to-14.2 V when TC was disconnected from normal.The output voltage of the designed circuit was 0 V to 10 V in the temperature range of 0°C to 1400°C.The results of the 4-channel interface experiment using R-type TC were almost identical to the CJC and disconnection detection results for each channel.The implemented multi-channel interface has a feature that can be applied equally to E,J,K,T,R,and S-type TCs by changing the terminals of CJC semiconductor devices and adjusting the IA gain.

Validation of the albumin-bilirubin score for identifying decompensation risk in patients with compensated cirrhosis

BACKGROUND The albumin-bilirubin(ALBI)score is an index of liver function recently developed to assess prognosis in patients with hepatocellular carcinoma(HCC).It can detect small changes in liver dysfunction and has been successfully applied to the prediction of survival in patients with non-malignant liver diseases of various etiologies.AIM To investigate the ALBI score for identifying decompensation risk at the 3-year follow-up in patients with compensated cirrhosis.METHODS One-hundred and twenty-three patients with compensated cirrhosis without HCC in King Chulalongkorn Memorial Hospital diagnosed by imaging were retrospectively enrolled from January 2016 to December 2020.A total of 113 patients(91.9%)had Child A cirrhosis with a median model for end-stage liver disease(MELD)score of less than 9.Baseline clinical and laboratory variables and decompensation events were collected.The ALBI score was calculated and validated to classify decompensation risk into low-,middle-,and high-risk groups using three ALBI grade ranges(ALBI grade 1:≤-2.60;grade 2:>-2.60 but≤-1.39;grade 3:>-1.39).Decompensation events were defined as ascites development,variceal bleeding,or grade 3 or 4 hepatic encephalopathy.RESULTS Among 123 cirrhotic patients enrolled,13.8%(n=17)developed decompensating events at a median time of 25[95%confidence interval(CI):17-31]mo.Median baseline ALBI score in compensated cirrhosis was significantly lower than that of patients who developed decompensation events[-2.768(-2.956 to-2.453)vs-2.007(-2.533 to-1.537);P=0.01].Analysis of decompensation risk at 3 years showed that ALBI score had a time-dependent area under the curve(tAUC)of 0.86(95%CI:0.78-0.92),which was significantly better than that of ALBI-Fibrosis-4(ALBI-FIB4)score(tAUC=0.77),MELD score(tAUC=0.66),Child-Pugh score(tAUC=0.65),and FIB-4 score(tAUC=0.48)(P<0.05 for all).The 3-year cumulative incidence of decompensation was 3.1%,22.6%,and 50%in the low-,middle-,and high-risk groups,respectively(P<0.001).The odds ratio for decompensation in patients of the high-risk group was 23.33(95%CI:3.88-140.12,P=0.001).CONCLUSION The ALBI score accurately identifies decompensation risk at the 3-year follow-up in patients with compensated cirrhosis.Those cirrhotic patients with a high-risk grade of ALBI score showed a 23 times greater odds of decompensation.

Excavation compensation theory and supplementary technology system for large deformation disasters

Given the challenges in managing large deformation disasters in energy engineering,traffic tunnel engineering,and slope engineering,the excavation compensation theory has been proposed for large deformation disasters and the supplementary technology system is developed accordingly.This theory is based on the concept that“all destructive behaviors in tunnel engineering originate from excavation.”This paper summarizes the development of the excavation compensation theory in five aspects:the“theory,”“equipment,”“technology,”the design method with large deformation mechanics,and engineering applications.First,the calculation method for compensation force has been developed based on this theory,and a comprehensive large deformation disaster control theory system is formed.Second,a negative Poisson's ratio anchor cable with high preload,large deformation,and super energy absorption characteristics has been independently developed and applied to large deformation disaster control.An intelligent tunnel monitoring and early warning cloud platform system are established for remote monitoring and early warning system of Newton force in landslide geological hazards.Third,the double gradient advance grouting technology,the two-dimensional blasting technology,and the integrated Newton force monitoring--early warning--control technology are developed for different engineering environments.Finally,some applications of this theory in China's energy,traffic tunnels,landslide,and other field projects have been analyzed,which successfully demonstrates the capability of this theory in large deformation disaster control.

A high frequency vibration compensation approach for ultrahigh resolution SAR imaging based on sinusoidal frequency modulation Fourier-Bessel transform

Ultrahigh resolution synthetic aperture radar(SAR)imaging for ship targets is significant in SAR imaging,but it suffers from high frequency vibration of the platform,which will induce defocus into SAR imaging results.In this paper,a novel compensation method based on the sinusoidal frequency modulation Fourier-Bessel transform(SFMFBT)is proposed,it can estimate the vibration errors,and the phase shift ambiguity can be avoided via extracting the time frequency ridge consequently.By constructing the corresponding compensation function and combined with the inverse SAR(ISAR)technique,well-focused imaging results can be obtained.The simulation imaging results of ship targets demonstrate the validity of the proposed approach.

A Compensation Algorithm for Large Element Characterizing the Damage Evolution Process and Its Application to Structure Collisions

When simulating the process from elastic–plastic deformation,damage to failure in a metal structure collision,it is necessary to use the large shell element due to the calculation efficiency,but this would affect the accuracy of damage evolution simulation.The compensation algorithm adjusting failure strain according to element size is usually used in the damage model to deal with the problem.In this paper,a new nonlinear compensation algorithm between failure strain and element size was proposed,which was incorporated in the damage model GISSMO(Generalized incremental stress state dependent damage model)to characterize ductile fracture.And associated material parameters were calibrated based on tensile experiments of aluminum alloy specimens with notches.Simulation and experimental results show that the new compensation algorithm significantly reduces the dependence of element size compared with the constant failure strain model and the damage model with the linear compensation algorithm.During the axial splitting process of a circular tubular structure,the new compensation algorithm keeps the failure prediction errors low over the stress states ranging from shear to biaxial tension,and achieves the objective prediction of the damage evolution process.This study demonstrates how the compensation algorithm resolves the contradiction between large element size and fracture prediction accuracy,and this facilitates the use of the damage model in ductile fracture prediction for engineering structures.

Minimum eigenvalue based adaptive fault compensation for hypersonic vehicles

The attitude tracking control problem is addressed for hypersonic vehicles under actuator faults that may cause an uncertain time-varying control gain matrix.An adaptive compensation scheme is developed to ensure system stability and asymptotic tracking properties,including a kinematic control signal and a dynamic control signal.To deal with the uncertainties of the control gain matrix,a new positive definite one is constructed.The minimum eigenvalue of such a new control gain matrix is estimated.Simulation results of application to an X-33 vehicle model verify the effectiveness of the proposed minimum eigenvalue based adaptive fault compensation scheme.

Pre-compensation of Friction for CNC Machine Tools through Constructing a Nonlinear Model Predictive Scheme

Nonlinear friction is a dominant factor afecting the control accuracy of CNC machine tools.This paper proposes a friction pre-compensation method for CNC machine tools through constructing a nonlinear model predictive scheme.The nonlinear friction-induced tracking error is frstly modeled and then utilized to establish the nonlinear model predictive scheme,which is subsequently used to optimize the compensation signal by treating the friction-induced tracking error as the optimization objective.During the optimization procedure,the derivative of compensation signal is constrained to avoid vibration of machine tools.In contrast to other existing approaches,the proposed method only needs the parameters of Stribeck friction model and an additional tuning parameter,while fnely identifying the parameters related to the pre-sliding phenomenon is not required.As a result,it greatly facilitates the practical applicability.Both air cutting and real cutting experiments conducted on an in-house developed open-architecture CNC machine tool prove that the proposed method can reduce the tracking errors by more than 56%,and reduce the contour errors by more than 50%.

Optimal design of culling compensation policy under the African swine fever——Based on simulations of typical pig farms in China

This paper aims to optimize the culling compensation policy from a micro perspective through scenario simulation.Based on an investigation of 273 pig farms in eight regions,four typical pig farms were constructed according to farm size and breeding mode,representing the swine producers in China.Besides,a decision objective function of pig farms facing suspected African swine fever(ASF)outbreaks was constructed.This study used a mathematical programming model to design and simulate scenarios based on compensation standards and local implementation levels,aiming to incentivize pig farms to report epidemics.The results show that the optimal decisions on epidemic reports differed among typical farms and by herd daily age.The results suggest the following adjustments for optimizing culling compensation policies:(1)to set culling compensation standards based on the market value and(2)to maintain a high level of epidemic surveillance capability in the animal husbandry and veterinary sector.

Improved High Order Model-Free Adaptive Iterative Learning Control with Disturbance Compensation and Enhanced Convergence

In this paper,an improved high-order model-free adaptive iterative control(IHOMFAILC)method for a class of nonlinear discrete-time systems is proposed based on the compact format dynamic linearization method.This method adds the differential of tracking error in the criteria function to compensate for the effect of the random disturbance.Meanwhile,a high-order estimation algorithmis used to estimate the value of pseudo partial derivative(PPD),that is,the current value of PPD is updated by that of previous iterations.Thus the rapid convergence of the maximumtracking error is not limited by the initial value of PPD.The convergence of the maximumtracking error is deduced in detail.This method can track the desired output with enhanced convergence and improved tracking performance.Two examples are used to verify the convergence and effectiveness of the proposed method.

Subsea Compensation of Pressure Based on Reducer Bellows

In this study,the pressure compensation mechanism of a reducer bellows is analyzed.This device is typically used to reduce the size of undersea instruments and improve related pressure resistance and sealing capabilities.Here,its axial stiffness is studied through a multi-fold approach based on theory,simulations and experiments.The results indicate that the mechanical strength of the reducer bellows,together with the oil volume and temperature are the main factors influencing its performances.In particular,the wall thickness,wave number,middle distance,and wave height are the most influential parameters.For a certain type of reducer bellows,the compensation capacity attains a maximum when the wave number ratio is between 6:6 and 8:4,the wall thickness is 0.3 mm,and the wave height is between 4–5 mm and 5–6 mm.Moreover,the maximum allowable ambient pres-sure of the optimized reducer bellows can reach 62.6 MPa without failure,and the maximum working water depth is 6284 m.