Correlations between mineral composition and mechanical properties of granite using digital image processing and discrete element method

This study investigated the correlations between mechanical properties and mineralogy of granite using the digital image processing(DIP) and discrete element method(DEM). The results showed that the X-ray diffraction(XRD)-based DIP method effectively analyzed the mineral composition contents and spatial distributions of granite. During the particle flow code(PFC2D) model calibration phase, the numerical simulation exhibited that the uniaxial compressive strength(UCS) value, elastic modulus(E), and failure pattern of the granite specimen in the UCS test were comparable to the experiment. By establishing 351 sets of numerical models and exploring the impacts of mineral composition on the mechanical properties of granite, it indicated that there was no negative correlation between quartz and feldspar for UCS, tensile strength(σ_(t)), and E. In contrast, mica had a significant negative correlation for UCS, σ_(t), and E. The presence of quartz increased the brittleness of granite, whereas the presence of mica and feldspar increased its ductility in UCS and direct tensile strength(DTS) tests. Varying contents of major mineral compositions in granite showed minor influence on the number of cracks in both UCS and DTS tests.

STUDIES ON THE FROTH CHARACTERISTICS OF COMPOSITE COLLECTORS IN NONMETALLIC MINERAL FLOTATION

The flotation results of a phosphate ore are improved by replacing the conventional collectors of fatty acids with composite collectors. The synergistic effect on the froth characteristics in systems using composite collectors has then been studied, and the concept of 'mixed hemimicellae' has been proposed in the adsorption of composite collectors at the air/solution interfaces.

Long-Term Effect of Fertilizer and Rice Straw on Mineral Composition and Potassium Adsorption in a Reddish Paddy Soil

Increasing K＋ adsorption can be an effective alternative in building an available K pool in soils to optimize crop recovery and minimize losses into the environment. We hypothesized that long-term fertilization might change K＋ adsorption because of changes in the chemical and mineralogical properties of a rice （Oryza sativa L.）. The aims of this study were （i） to determine clay minerals in paddy soil clay size fractions using X-ray diffraction methods and a numerical diagramdecomposition method; （ii） to measure K＋ adsorption isotherms before and after H202 oxidation of organic matter, and （iii） to investigate whether K＋ adsorption is correlated with changes in soil chemical and mineral properties. The 30-yr longterm fertilization treatments caused little change in soil organic C （SOC） but a large variation in soil mineral composition. The whole-clay fraction （〈5 Jam） corresponded more to the fertilization treatment than the fine-clay fraction （〈1 gin） in terms of percentage of illite peak area. The total percentage of vermiculite-chlorite peak area was significantly negatively correlated with the total percentage ofillite peak area in the 〈5 lam soil particles （R=-0.946, P〈0.0006）. Different fertilization treatments gave significantly different results in K＋ adsorption. The SOC oxidation test showed positive effects of SOC on K＋ adsorption at lower K＋ concentration （≤120 mg L-0 and negative effects at higher K＋ concentration （240 mg L-l）. The K＋ adsorption by soil clay minerals after SOC oxidization accounted for 60-158% of that by unoxidized soils, suggesting a more important role of soil minerals than SOC on K＋ adsorption. The K＋ adsorption potential was significantly correlated to the amount of poorly crystallized illite present （R--0.879, P=0.012）. The availability of adsorbed K＋ for plant growth needs further study.

Textures and mineral compositions of the Xinjie layered intrusion,SW China:Implications for the origin of magnetite and fractionation process of Fe-Ti-rich basaltic magmas

The Xinjie layered intrusion in the Panxi region,SW China,hosts both Fe-Ti oxide and platinum-group element（PGE） sulfide mineralization.The intrusion can be divided,from the base upward,into UnitsⅠ,ⅡandⅢ,in terms of mineral assemblages.UnitsⅠandⅡare mainly composed of wehrlite and clino-pyroxenite, whereas UnitⅢis mainly composed of gabbro.PGE sulfide-rich layers mainly occur in Unit I, whereas thick Fe-Ti oxide-rich layers mainly occur in UnitⅢ.An ilmenite-rich layer occurs at the top of UnitⅠ.Fe-Ti oxides include magnetite and ilmenite.Small amounts of cumulus and intercumulus magnetite occur in UnitsⅠandⅡ.Cumulus magnetite grains are commonly euhedral and enclosed within olivine and clinopyroxene.They have high Cr2O3 contents ranging from 6.02 to 22.5 wt.%,indicating that they are likely an early crystallized phase from magmas.Intercumulus magnetite that usually displays ilmenite exsolution occupies the interstices between cumulus olivine crystals and coexists with interstitial clinopyroxene and plagioclase.Intercumulus magnetite has Cr2O3 ranging from 1.65 to 6.18 wt.%, lower than cumulus magnetite.The intercumulus magnetite may have crystallized from the trapped liquid.Large amounts of magnetite in UnitⅢcontains Cr2O3（＆lt;0.28 wt.%） much lower than magnetite in UnitsⅠandⅡ.The magnetite in UnitⅢis proposed to be accumulated from a Fe-Ti-rich melt.The Fe-Ti-rich melt is estimated to contain 35.9 wt.%of SiO2,26.9 wt.%of FeOt,8.2 wt.%of TiO2,13.2 wt.%of CaO, 8.3 wt.%of MgO,5.5 wt.%of Al2O3 and 1.0 wt.%of P2O5.The composition is comparable with the Fe-rich melts in the Skaergaard and Sept Iles intrusions.Paired non-reactive microstructures,granophyre pockets and ilmenite-rich intergrowths,are representative of Si-rich melt and Fe-Ti-rich melt,and are the direct evidence for the existence of an immiscible Fe-Ti-rich melt that formed from an evolved ferro-basaltic magma.

Mineralogical characterization of airborne individual particulates in Beijing PM10

This work mainly focuses on the mineralogical study of particulate matter（PM10） in Beijing. Samples were collected on polycarbonate filter from April, 2002 to March, 2003 in Beijing urban area. Scanning electronic microscopy coupled with energy dispersive X-ray（SEM/EDX） was used to investigate individual mineral particles in Beijing PM10. 1454 individual mineral particulates from 48 samples were analysed by SEM/EDX. The results revealed that mineral particulates were complex and heterogeneous. 38 kinds of minerals in PM10 were identified. The clay minerals, of annual average percentage of 30.1%, were the main composition among the identified minerals, and illite/smectite was the main composition in clay minerals, reaching up to 35%. Annual average percentage of quartz, calcite, compound particulates, carbonates were 13.5%, 10.9%, 11.95%, 10.31%, respectively. Annual average percentage less than 10% were gypsum, feldspar, dolomite, and so on. Fluorite, apatite, halite, barite and chloridize zinc（ZnCl2） were firstly identified in Beijing PM10. Sulfurization was found on surface of mineral particles, suggested extensive atmospheric reaction in air during summer.

Mineral composition and organic geochemistry of the Lower Cretaceous Xiagou Formation source rock from the Qingxi Sag,Jiuquan Basin, Northwest China

The Lower Cretaceous Xiagou Formation contains the major source rocks for the crude oils discovered in the Qingxi Sag and the South Uplift in the Jiuquan Basin, northwestern China. The Xiagou Formation source rock was formed in a closed,anoxic, reducing, alkaline lacustrine environment with a high salinity. Its high content of brittle minerals is favorable for the fracturing of reservoirs in source rock formations in the Qingxi Sag. The Xiagou Formation contains a great number of fair to excellent source rocks, and their organic matter（OM） came chiefly from plankton/algae and high plants as well as possibly bacterial organisms. The Xiagou Formation source rocks mainly contain Type II OM and some Type III and Type I OM, with good oil-generating potential. The source rock maturity is mainly in the early-mature and mature stages, and its Rovalue corresponding to oil peak is about 0.8%, which is lower than classic oil peak Rovalue of 1.0%; therefore, a great deal of hydrocarbon was generated before the classic oil peak Ro= 1.0%. Mature source rock in the Xiagou Formation tends to be distributed in the older members and at a greater depth. There is a better exploration potential of tight oil in the deep Qingxi Sag.

Petrogenesis and Mineralization of Two-Stage A-Type Granites in Jiuyishan,South China:Constraints from Whole-rock Geochemistry, Mineral Composition and Zircon U-Pb-Hf Isotopes

The Jiuyishan complex massif,located in the northern section of the Nanling region,is a combination of five plutons,namely,the Xuehuading,Jinjiling,Pangxiemu,Shaziling and Xishan plutons.Whole-rock geochemistry,Imineral electron microprobe analysis,zircon U-Pb dating and Hf isotope analysis were carried out for the Jinjiling and Pangxiemu plutons.The zircon U-Pb dating yields weighted mean ages of 152.9±0.9 Ma for the Jinjiling pluton and 151.7±1.5 Ma for the Pangxiemu pluton,with a narrow gap between them.The Jinjiling and Pangxiemu plutons both have geochemical characteristics of high SiO2,Al2 O3,Na2 O,K2 O and low TiO2,MgO,CaO,P2 O5 contents,with intense depletions in Sr,Ba,Ti,Eu and enrichments in Ga,FeoOT and HFSE,and these characteristics reflect an A-type affinity.From the Jinjiling to the Pangxiemu plutons,the mineral composition of mica changes from lepidomelane to zinnwaldite,with increases in F,Li2 O and Rb2 O contents.The mineral composition of zircon changes from low Zr/Hf to high Zr/Hf,with increasing HfO2,P2 O5 and UO2+ThO2+Y2 O3 contents.The mineral compositions of feldspar indicate that the Pangxiemu pluton contains more alkali feldspar than the Jinjiling pluton.The whole-rock geochemistry and mineral compositions reveal a higher degree of differentiation for the Pangxiemu pluton.The nearly uniformεHf(t)indicates the same source region for the two plutons:both were derived from partial melting of the lower crust,with small contributions of mantle materials.In addition,higher F,lower Nb/Ta and Zr/Hf ratios in the Pangxiemu Pluton suggest a closer relationship with the rare metal mineralization than for the Jinjiling pluton.

Mineralogical and Active Mechanical Excitation Characteristics of Filled Fly Ash Cementitious Materials

To reveal the influence of mechanical activation on the performance of fly ash, the microanalysis（the energy spectroscopy, XRD and SEM）, the distribution size of particle of fly ash and cement paste intensity of various age for different grinding time were studied. The relationships of the activity and the composition of fly ash, microstructure and the distribution of particle size by mechanical activation of fly ash were obtained. The internal glass beads with activity were released by grinding fly ash for a certain time. The particle specific surface area was improved and the hydration reaction of the interface and the surface active center was increased by grinding. The granularity distributing of fly-ash trended towards optimization. The polar molecules or ions were easier to intrude into the internal cavity of the vitreous body. The active silica and alumina of fly ash were rapidly depolymerized. Each performance index of fly ash was increased before grinding for 20 min. Cement paste intensity of various age increased along with the grinding time, and the early strength increase range was big, but the later period intensity increase range hastened slightly. The internal part of vitreous of fly ash was destroyed if the fly ash continued to be ground and the activity of fly ash was reduced. It is suggested that Guozhuang＇s fly ash should be ground for 20 min.

Inversion of the Main Mineral Compositions and Subdivision of Tectonic Units on Lunar LQ-4 based on Chang'e Data

Spectra are sensitive in detecting main minerals on the lunar surface from visible light to infrared light. Since spectral characteristics of minerals are closely related to their compositions and the maturity level of soil on the Moon, studying the compositions and distribution of elements and minerals on the lunar surface can help to understand the evolution of the Moon through remote sensing technology. The correlation between the spectral characteristics of Chang＇e-1 interference imaging spectrometry（IIM） reflectance images and the mineral contents of LSCC（Lunar Soil Characterization Consortium） lunar surface mineral samples was discussed and the spatial distributions of Fe O and Al_2O_3 contained in both pyroxene and plagioclase on LQ-4 were studied using the improved angle parameter method, MNF, and band ratio statistics. A comparison of the mapping results of the optical models by Lucey, Shkuractov and other researchers on Clementine and the gamma ray spectrometry data shows that the content error is within 0.6% for lunar mare areas and close to 1% for the highland areas. The tectonic framework on the lunar surface was also investigated. And based on integrated analysis of previous findings on topography of the lunar surface, Chang＇e LAM, CCD and LOLA images and the gravity anomalies data（Clementine GLGM-2）, the tectonic unit subdivision was established for LQ-4, the idea of subdividing the lunar tectonic units was proposed, and this will provide a good foundation for studying the lunar tectonic evolution.

Distribution and composition of authigenic minerals in surface sediments of the western Gulf of Thailand

Generation, morphology, and distribution of authigenic minerals directly reflect sedimentary environment and material sources. Surface sediments were collected from the western Gulf of Thailand during 2011–2012, and 159 samples were analyzed to determine detrital minerals. Authigenic minerals, including siderite, pyrite, and glauconite, are abundant whereas secondary minerals, such as chlorite and limonite, are distributed widely in the study area. Siderite has a maximum content of 19.98 g/kg and appears in three types from nearshore to continental shelf, showing the process of forming-maturity-oxidation. In this process, the Mn O content in siderite decreases, but FeOand Mg O content increase. Colorless or transparent siderite pellets are fresh grains generated within a short time and widely distributed throughout the region; high content appears in coastal area where river inputs are discharged. Translucent cemented double pellets appearing light yellow to red are mature grains; high content is observed in the central shelf. Red-brown opaque granular pellets are oxidized grains,which are concentrated in the eastern gulf. Pyrite is mostly distributed in the central continental shelf with an approximately north–south strip. Pyrite are mainly observed in foraminifera shell and distributed in clayey silt sediments, which is similar to that in the Yangtze River mouth and the Yellow Sea. The pyrite in the gulf is deduced from genetic types associated with sulfate reduction and organic matter decomposition. Majority of glauconite are granular with few laminar. Glauconite is concentrated in the northern and southern parts within the boundary of 9.5° to 10.5°N and is affected by river input diffusion. The distribution of glauconite is closely correlated with that of chlorite and plagioclase, indicating that glauconite is possibly derived from altered products of chlorite and plagioclase. The KO content of glauconite is low or absent, indicating its short formation time.

Nanoscale mechanical property variations concerning mineral composition and contact of marine shale

Mechanical properties of shales are key parameters influencing hydrocarbon production – impacting borehole stability, hydraulic fracture extension and microscale variations in in situ stress. We use Ordovician shale(Sichuan Basin, China) as a type-example to characterize variations in mineral particle properties at microscale including particle morphology, form of contact and spatial distribution via mineral liberation analysis(MLA) and scanning electron microscopy(SEM). Deformation-based constitutive models are then built using finite element methods to define the impact of various architectures of fracture and mineral distributions at nanometer scale on the deformation characteristics at macroscale.Relative compositions of siliceous, calcareous and clay mineral particles are shown to be the key factors influencing brittleness. Shales with similar mineral composition show a spectrum of equivalent medium mechanical properties due to differing particle morphology and mineral heterogeneity. The predominance of small particles and/or point-point contacts are conducive to brittle failure, in general, and especially so when quartz-rich. Fracture morphology, length and extent of filling all influence shale deformability. High aspect-ratio fractures concentrate stress at fracture tips and are conducive to extension, as when part-filled by carbonate minerals. As fracture spacing increases, stress transfer between adjacent fractures weakens, stress concentrations are amplified and fracture extension is favored. The higher the fractal dimension of the fracture and heterogeneity of the host the more pervasive the fractures. Moreover, when fractures extend, their potential for intersection and interconnection contributes to a reduction in strength and the promotion of brittle failure. Thus, these results provide important theoretical insights into the role of heterogeneity on the deformability and strength of shale reservoirs with practical implications for their stimulation and in the recovery of hydrocarbons from them.

Experimental of the influence of mineral composition and normal stress on the frictional slip of shale

Natural fractures are widely distributed in shale reservoirs.During the hydraulic fracturing process,frictional slip occurring on natural fractures can increase the reservoir permeability and is of great significance to improve the efficiency of reservoir stimulation.Shale contains a large amount of clay and organic matter,and its frictional behavior is different from that of other previously studied lithologies.In this paper,the frictional behavior of shale is analyzed,and the results show that the frictional behavior is controlled by the content of clay and organic matter.As the content of clay and organic matter increases,the micro support type transforms from the particle support mode by hard quartz mineral to matrix support mode by plastic clay and organic matter.Accordingly,the shear strength and friction coefficient of shale both decrease,and the shear type transforms from brittle to plastic.When the content of clay and organic matter is low,the asperity of friction surfaces will break in a brittle manner and the wear degree of surfaces is low.Therefore,fractures are still featured by moderate apertures after friction.The lower the content of clay and organic matter is,the easier the asperity of crack surfaces supports themselves,and the higher the fracture residual permeability is.Thus,promoting shear slip is the main measure of reservoir stimulation.However,when the content of clay and organic matter is high,the remaining post-slip fracture aperture is small.It is difficult to increase reservoir permeability through the frictional slip of natural fractures,and in this situation,the proppant support efficiency needs to be improved.

Study on properties of sinter mineral phases

In this study,the properties of sinter mineral phases were investigated by X-ray diffraction,optical microscopy quantitative observation,electron probe microanalysis,and the nanoindentation technique. The mechanisms that form return fines are discussed with respect to the factors of microregion composition,sintering temperature,and the reactive behavior of pisolite. The study results indicate the following：（ 1） Sinter mineral assemblage mainly comprises hematite,magnetite,calcium ferrite,and glass. In addition,the mineral assemblage of sinter products includes a great deal of calcium ferrite and melt-erosive magnetite,an abundance of secondary hematite,and a small amount of primary iron ore; whereas the mineral assemblage of return fines contains plentiful amounts of euhedral magnetite and secondary hematite,a large amount of relic pisolite with particle sizes less than1 mm,and relatively less calcium ferrite. In particular,some calcium ferrite was found to coexist with relic iron ore in a fiber-like microstructure.（ 2） Dentritic calcium ferrite has less SiO_2 and Al_2O_3,higher basicity（ w_（CaO）/w_（SiO_2））and a mole ratio of Fe_2O_3/CaO,whereas platy and blocky calcium ferrites have more SiO_2 and Al_2O_3,lower basicity and a mole ratio of Fe_2O_3/CaO.（ 3） The hardness of hematite is the highest（ around 18-22 GPa）,those of calcium ferrite and magnetite are relatively lower,and that of glass is the lowest. In terms of the formation mechanism of return fines,because of their weak ability to resist external shocks,these sorts of mineral phases and microstructures-（1） euhedral magnetite and glass formed in microregions with low basicity;（2） SFCA-Ⅰand relic iron ore formed in regions with a relatively low sintering temperature; and（3） relic pisolite and its nearby reaction regions-are inclined to form return fines.

Nutritional and Mineral Variability in 52 Accessions of Common Bean Varieties(Phaseolus vulgaris L.)from Madeira Island

The Phaseolus vulgaris L. is one of the traditional and most important leguminous crops in the Island of Madeira. The island’s bioclimatic tiers, agro-ecological environment and traditional farming practices had a great influence on the evolution of regional bean landraces. The variability of the nutritional and mineral seeds composition of 59 accessions of the Madeiran landraces, standard and commercial varieties was evaluated. Wide ranges of variability in biochemical parameters were reported among the Madeiran landraces, being the best sources of protein and mineral nutrition, according to the statistical results and literature comparative evaluation. Specifically, the content (g per 100 g DW) of ash ranged from 3.64-5.67, lipids from 0.57-2.86, protein from 18.55-29.69, starch from 23.40-52.65, soluble sugars from 2.97-6.84, while content of dry matter was from 83.35-93.55. The seeds also contained (per 100 g DW) between 2.55-4.83 g N, 0.30-7.50 g P, 1.30-2.49 g K, 0.10-0.18 g Mg, 4.10-10.00 mg Fe, 50.0-1.40 mg Cu, 2.20-5.00 mg Zn, 0.90-3.80 μg Mn and 0.20-2.40 μg B. This variability implies that the screened germplasm could serve as a source for breeding new varieties with improved biochemical and nutritional traits or could be highly recommended to meet specific dietary requirements. The cultivar Vaginha Grossa (ISOP 713) revealed low carbohydrate content that could be a good food choice for diabetics, while cultivar Vermelho (ISOP 724) bean should be offered as a valuable alternative source of protein and minerals in the local diet.

Application of sequential extraction for analyzing source and sink of uranium in Huanghe River sediments,China

Geochemical behaviors of heavy metals are closely related to their chemical state that can be divided by sequential extraction into exchangeable(F1),bound to carbonates(F2),bound to Fe-Mn oxides(F3),bound to organic matter or sulfide(F4),and residual(F5).Uranium in sediment of the Huanghe(Yellow)River,China,in different chemical states was extracted using the five-step procedure of Tessier and the source and sink were analyzed.Results show that more than 70%of the total uranium was immobile residual F5 in abundance,followed in order of F4>F3>F2>F1,indicating that the main source of uranium in the sediments was from weathered rock in the drainage basin.In addition,the uranium in the sediments presents potential exogenous input in the Lanzhou,Baotou,and Tongguan reach.Fe-Mn oxides are main carriers of unstable uranium,especially those of F1 and F3.Calcite and illite are secondary adsorption minerals of unstable uranium in sediments under natural conditions.Human activities can also produce an obvious impact on uranium speciation.This study provides a reference for the application of sequential extraction in analyzing the source and sink of uranium in river sediments.

Analysis and Evaluation of Nutrient Composition in the Wild, Pond- and Lake-Cultured Topmouth Culter (Culter alburnus)

Research was conducted on topmouth culter (Culter alburnus) grown in ponds and lakes as well as wild types in order to determine their chemical composition and nutritional value. There are three types of fish that differ in their proximate composition, amino acids, fatty acids, and minerals. Wild fish had a significantly lower crude lipid contents than cultured fish (P P ∑PUFAs) showed an obviously opposite trend. As compared with cultured fish, wild fish had significantly higher levels of n-3 PUFAs, arachidonic acid (AA), eicosapentaenoic acid (EPA) and docosahxaenoic acid (DHA) (P P > 0.05), except for Na, Fe and Se. In conclusion, diet composition and external aqueous environment may determine the differences between wild and cultured topmouth culter.

Physicochemical characteristics of ambient particles settling upon leaf surfaces of urban plants in Beijing

Particulate pollution is a serious health problem throughout the world, exacerbating a wide range of respiratory and vascular illnesses in urban areas. Urban plants play an important role in reducing particulate pollution. Physicochemical characteristics of ambient particles settling upon leaf surfaces of eleven roadside plants at four sites of Beijing were studies. Results showed that density of particles on the leaf surfaces greatly varied with plant species and traffic condition. Fraxinus chiuensis, Sophora japonica Ailanthus altissima, Syringa oblata and Prunus persica, had larger densities of particles among the tall species. Due to resuspension of road dust, the densities of particles of Euonymus japonicns and Parthenocissus quinquefolia with low sampling height were 2-35 times to other taller tree species. For test plant species, micro-roughness of leaf surfaces and density of particles showed a close correlation. In general, the larger micro-roughness of leaf surfaces is, the larger density of particles is. Particles settling upon leaf surfaces were dominantly PM30 （particulate matter less than 10 μm in aerodynamic diameter; 98.4%） and PM2.5 （particulate matter less than 2.5 μm in aerodynamic diameter; 64.2%） which were closely relative to human health. Constant elements of particles were C, O, K, Ca, Si, Al, Mg, Na, Fe, S, Cl and minerals with higher content were SiO2, CaCO3, CaMg（CO3）2, NaCI and 2CASO4. H2O, SiO2. CaCO3 and CaMg（CO3）2 mainly came from resuspension of road dust. 2CaSO4. H2O was produced by the reaction between CaCO3 derived from earth dust or industrial emission and SO2, H2SO4 or sulfate. NaCl was derived from sea salt.

A New Kind of Eco-Cement Made of Cement Kiln Dust and Granular Blast Furnace Slag

A research project wus conducted to manufacture eco-cement for sustainable development using cement kiln dust（ CKD ） and granular blast furnace slag（ GBFS ）. In the project, the burning process and minerul compositions of CKD dinker were investigated. Different minerulizers such as CaSO4 and CaF2 , sulfur and alkali corttent were coasidered. The strength of CKD and GBFS eco-cement were evaluated. The results indicate the CKD clinker can not only form ordinary cement clinker minerals such as C3 S, C2 S and C4 AF , but also form such high-reuctive minerals as C4 A3 S and C. A7 · CaF2 . The CKD and GBFS eco-cement will have the similar strength to the Portland cement grade 32.5 when blend proportion is properly applied.

Prediction of multiscale laminae structure and reservoir quality in fine-grained sedimentary rocks:The Permian Lucaogou Formation in Jimusar Sag,Junggar Basin

Fine-grained sedimentary rocks have become a research focus as important reservoirs and source rocks for tight and shale oil and gas.Laminae development determines the accumulation and production of tight and shale oil and gas in fine-grained rocks.However,due to the resolution limit of conventional logs,it is challenging to recognize the features of centimeter-scale laminae.To close this gap,complementary studies,including core observation,thin section,X-ray diffraction(XRD),conventional log analysis,and slabs of image logs,were conducted to unravel the centimeter-scale laminae.The laminae recognition models were built using well logs.The fine-grained rocks can be divided into laminated rocks(lamina thickness of<0.01 m),layered rocks(0.01-0.1 m),and massive rocks(no layer or layer spacing of>0.1 m)according to the laminae scale from core observations.According to the mineral superposition assemblages from thin-section observations,the laminated rocks can be further divided into binary,ternary,and multiple structures.The typical mineral components,slabs,and T2spectrum distributions of various lamina types are unraveled.The core can identify the centimeter-millimeter-scale laminae,and the thin section can identify the millimeter-micrometer-scale laminae.Furthermore,they can detect mineral types and their superposition sequence.Conventional logs can identify the meter-scale layers,whereas image logs and related slabs can identify the laminae variations at millimeter-centimeter scales.Therefore,the slab of image logs combined with thin sections can identify laminae assemblage characteristics,including the thickness and vertical assemblage.The identification and classification of lamina structure of various scales on a single well can be predicted using conventional logs,image logs,and slabs combined with thin sections.The layered rocks have better reservoir quality and oil-bearing potential than the massive and laminated rocks.The laminated rocks’binary lamina is better than the ternary and multiple layers due to the high content of felsic minerals.The abovementioned results build the prediction model for multiscale laminae structure using well logs,helping sweet spots prediction in the Permian Lucaogou Formation in the Jimusar Sag and fine-grained sedimentary rocks worldwide.

Frictional stability of Longmaxi shale gouges and its implication for deep seismic potential in the southeastern Sichuan Basin

Microearthquakes accompanying shale gas recovery highlight the importance of exploring the frictional and stability properties of shale gouges.Aiming to reveal the influencing factors on fault stability,this paper explores the impact of mineral compositions,effective stress and temperature on the frictional stability of Longmaxi shale gouges in deep reservoirs located in the Luzhou area,southeastern Sichuan Basin.Eleven shear experiments were conducted to define the frictional strength and stability of five shale gouges.The specific experimental conditions were as follows:temperatures:90–270°C;a confining stress:95 MPa;and pore fluid pressures:25–55 MPa.The results show that all five shale gouges generally display high frictional strength with friction coefficients ranging from 0.60 to 0.70 at the aforementioned experiment condition of pressures,and temperatures.Frictional stability is significantly affected by temperature and mineral compositions,but is insensitive to variation in pore fluid pressures.Fault instability is enhanced at higher temperatures(especially at>200°C)and with higher tectosilicate/carbonate contents.The results demonstrate that the combined effect of mineral composition and temperature is particularly important for induced seismicity during hydraulic fracturing in deep shale reservoirs.