Intact rock is typically described according to its uniaxial compressive strength （UCS）. The UCS is needed in the design of geotechnical engineering problems including stability of rock slopes and design of shallow ...Intact rock is typically described according to its uniaxial compressive strength （UCS）. The UCS is needed in the design of geotechnical engineering problems including stability of rock slopes and design of shallow and deep foundations resting on and/or in rocks. Accordingly, a correct measure-ment/evaluation of the UCS is essential to a safe and economic design. Typically, the UCS is measured using the unconfined compression tests performed on cylindrical intact specimens with a minimum length to width ratio of 2. In several cases, especially for weak and very weak rocks, it is not possible to extract intact specimens with the needed minimum dimensions. Thus, alternative tests （e.g. point load test, Schmidt hammer） are used to measure rock strength. The UCS is computed based on the results of these tests through empirical correlations. The literature includes a plethora of these correlations that vary widely in estimating rock strength. Thus, it is paramount to validate these correlations to check their suitability for estimating rock strength for a specific location and geology. A review of the available correlations used to estimate the UCS from the point load test results is performed and summarized herein. Results of UCS, point load strength index and Young＇s modulus are gathered for calcareous sandstone specimens extracted from the Dubai area. A correlation for estimating the UCS from the point load strength index is proposed. Furthermore, the Young＇s modulus is correlated to the UCS.展开更多
Fe40Ni40P14B6 bulk metallic glass rods have been prepared by water quenching the fluxed alloy. The deformation behavior was investigated by nanoindentation tests and compressing tests. The average hardness and elastic...Fe40Ni40P14B6 bulk metallic glass rods have been prepared by water quenching the fluxed alloy. The deformation behavior was investigated by nanoindentation tests and compressing tests. The average hardness and elastic modulus of the as-prepared Fe40Ni40P14B6 BMG (bulk metallic glass) measured by nanoindentation tests are 8.347 and 176.61 GPa respectively. The displace- ment-load curve shows “pop-in” characteristics which correspond to the loading rate bursts. Many shear bands around the indent were observed. The as-prepared Fe-based BMG exhibits a compressive plastic strain of 5.21%, which is much larger than that of other Fe-based glassy alloys and most of other BMGs.展开更多
With the development of the micro-electro-mechanical system (MEMS),the flow characteristics in micro-channels have drawn increasing attention.In this paper,numerical simulations are conducted to investigate the flow c...With the development of the micro-electro-mechanical system (MEMS),the flow characteristics in micro-channels have drawn increasing attention.In this paper,numerical simulations are conducted to investigate the flow characteristics of compressible flow through micro-channels and micronozzles.An improved surface roughness viscosity model is used to simulate the effect of surface roughness on micro-channels flow characteristics.Using this model,better agreements between the computational results and the experimental data are found.The result indicates that the surface roughness is one of the important factors affecting the flow characteristics of gas through micro-channels.The numerical investigation on the expansion channel shows that by using the laminar model that considers surface roughness,the computational results and experimental data are consistent when Re<450,whereas deviation increases when Re>450.Based on the synthetic model with considerations of turbulence viscosity and surface roughness,the numerical results and the experimental data are identical.展开更多
文摘Intact rock is typically described according to its uniaxial compressive strength （UCS）. The UCS is needed in the design of geotechnical engineering problems including stability of rock slopes and design of shallow and deep foundations resting on and/or in rocks. Accordingly, a correct measure-ment/evaluation of the UCS is essential to a safe and economic design. Typically, the UCS is measured using the unconfined compression tests performed on cylindrical intact specimens with a minimum length to width ratio of 2. In several cases, especially for weak and very weak rocks, it is not possible to extract intact specimens with the needed minimum dimensions. Thus, alternative tests （e.g. point load test, Schmidt hammer） are used to measure rock strength. The UCS is computed based on the results of these tests through empirical correlations. The literature includes a plethora of these correlations that vary widely in estimating rock strength. Thus, it is paramount to validate these correlations to check their suitability for estimating rock strength for a specific location and geology. A review of the available correlations used to estimate the UCS from the point load test results is performed and summarized herein. Results of UCS, point load strength index and Young＇s modulus are gathered for calcareous sandstone specimens extracted from the Dubai area. A correlation for estimating the UCS from the point load strength index is proposed. Furthermore, the Young＇s modulus is correlated to the UCS.
文摘Fe40Ni40P14B6 bulk metallic glass rods have been prepared by water quenching the fluxed alloy. The deformation behavior was investigated by nanoindentation tests and compressing tests. The average hardness and elastic modulus of the as-prepared Fe40Ni40P14B6 BMG (bulk metallic glass) measured by nanoindentation tests are 8.347 and 176.61 GPa respectively. The displace- ment-load curve shows “pop-in” characteristics which correspond to the loading rate bursts. Many shear bands around the indent were observed. The as-prepared Fe-based BMG exhibits a compressive plastic strain of 5.21%, which is much larger than that of other Fe-based glassy alloys and most of other BMGs.
基金supported by the National Natural Science Foundation of China(Grant No. 10872106)
文摘With the development of the micro-electro-mechanical system (MEMS),the flow characteristics in micro-channels have drawn increasing attention.In this paper,numerical simulations are conducted to investigate the flow characteristics of compressible flow through micro-channels and micronozzles.An improved surface roughness viscosity model is used to simulate the effect of surface roughness on micro-channels flow characteristics.Using this model,better agreements between the computational results and the experimental data are found.The result indicates that the surface roughness is one of the important factors affecting the flow characteristics of gas through micro-channels.The numerical investigation on the expansion channel shows that by using the laminar model that considers surface roughness,the computational results and experimental data are consistent when Re<450,whereas deviation increases when Re>450.Based on the synthetic model with considerations of turbulence viscosity and surface roughness,the numerical results and the experimental data are identical.
