Stress-strain behavior of plastic concrete using monotonic triaxial compression tests

The mechanical behavior of plastic concrete used in the cut-off walls of earth dams has been studied. Triaxial compression tests on the specimens in various ages and mix designs under different confining pressures have been done and the stress-strain behavior of such materials and their strength parameter changes have been experimentally investigated. It has been observed that increasing the confining pressures applied on the specimens causes the material behavior to be alike the more ductile materials and the compressive strength increases considerably as well. Moreover, a parametric study has been carded out to investigate the influence of essential parameters on the shear strength parameters of these materials. According to the research, increasing the coarse to fine aggregates ratio leads to the increase of compressive strength of the specimens as well as the increase of the cohesion and internal friction angle of the materials. Furthermore, the bentonite content decrease and the cement factor increase result in an increase of the cohesion parameter of plastic concretes and decrease of the internal friction angle of such materials.

Constitutive relationship of IN690 superalloy by using uniaxial compression tests

The hot deformation behavior of IN690 superalloy was characterized in a temperature range of 1273-1473 K and a strain rate range of 0.01-10 s^-1 using uniaxial compression tests on process annealed material.The constitutive relations between flow stress and effective strain,effective strain rate as well as deformation temperature were studied.It can be concluded that the flow stress significantly reduces with the deformation temperature of IN690 superalloy increasing.Whereas,there is a significant increase of flow stress when the strain rate increases from 0.1 s^-1 to 10 s^-1.Based on the hyperbolic-sine Arrhenius-type equation,a constitutive equation considering compensation of strain was developed.The activation energy and the material constants（Q,n and ln A） decrease as the deformation strain increases.The strain dependent term is successfully incorporated in the constitutive equation through a quartic equation.A good agreement between the experimental data and the predicted results has been achieved,indicating that the proposed constitutive equation and the methods of determing the material constants are suitable to model the high temperature deformation behavior of IN690 superalloy.

Variation of the friction conditions in cold ring compression tests of medium carbon steel

Lubrication and friction conditions vary with deformation during metal forming processes.Significant macro-variations can be observed when a threshold of deformation is reached.This study shows that during the cold compression processing of#45(AISI 1045)steel rings,the magnitude of friction and surface roughness(Ra)changes significantly upon reaching a 45%reduction in ring height.For example,the Ra of compressed ring specimens increased by approximately 55%immediately before and after reaching this threshold,compared to an 18% or 25%variation over a 35%-45%or a 45%-55%reduction in height,respectively.The ring compression test conducted by this study indicates that the Coulomb friction coefficient and Tresca friction factor mare 0.105 and 0.22,respectively,when the reduction in height is less than 45%;and 0.11 and 0.24,respectively,when the reduction in height is greater than 45%.

Three dimensional discrete element modelling of the conventional compression behavior of gas hydrate bearing coal

To analyze the relationship between macro and meso parameters of the gas hydrate bearing coal(GHBC)and to calibrate the meso-parameters,the numerical tests were conducted to simulate the laboratory triaxial compression tests by PFC3D,with the parallel bond model employed as the particle contact constitutive model.First,twenty simulation tests were conducted to quantify the relationship between the macro–meso parameters.Then,nine orthogonal simulation tests were performed using four meso-mechanical parameters in a three-level to evaluate the sensitivity of the meso-mechanical parameters.Furthermore,the calibration method of the meso-parameters were then proposed.Finally,the contact force chain,the contact force and the contact number were examined to investigate the saturation effect on the meso-mechanical behavior of GHBC.The results show that:(1)The elastic modulus linearly increases with the bonding stiffness ratio and the friction coefficient while exponentially increasing with the normal bonding strength and the bonding radius coefficient.The failure strength increases exponentially with the increase of the friction coefficient,the normal bonding strength and the bonding radius coefficient,and remains constant with the increase of bond stiffness ratio;(2)The friction coefficient and the bond radius coefficient are most sensitive to the elastic modulus and the failure strength;(3)The number of the force chains,the contact force,and the bond strength between particles will increase with the increase of the hydrate saturation,which leads to the larger failure strength.

Triaxial creep tests of weak sandstone from fracture zone of high dam foundation

The lithology of fracture zone which was developed at the dam foundation of a hydropower station is weak sandstone with poor integrity and pore cementation contact.Its creep properties have a significant impact on the deformation and stability of the dam.Based on the characteristics of loose organizational structure,high moisture content and poor mechanical properties,the triaxial compression tests and creep tests were carried out,respectively.The results show significant non-linear,low strength and no obvious strength peaks.Both axial and lateral strains are achieved more than 3%when the tests are failed.The weak sandstone has a significant creep property,but only transient and steady state appear under low stress.Increased stress causes creep intensified and lateral strain gradually exceeds axial strain.In the failure stage,it has characteristics of large axial plastic deformation,obvious volumetric ductility dilation and large steady creep rate.The accelerated creep appears shortly after transient loading under confining of pressures 1.0 MPa and 1.5 MPa.Therefore,an improved Burgers creep model considering the non-linear characteristics of weak sandstone is built based on hyperbolic equation and the creep parameters are identified.This model can well describe the creep properties of weak sandstone.

ADVANCED FREQUENCY-DIRECTED RUN-LENTH BASED CODING SCHEME ON TEST DATA COMPRESSION FOR SYSTEM-ON-CHIP

Test data compression and test resource partitioning （TRP） are essential to reduce the amount of test data in system-on-chip testing. A novel variable-to-variable-length compression codes is designed as advanced fre- quency-directed run-length （AFDR） codes. Different [rom frequency-directed run-length （FDR） codes, AFDR encodes both 0- and 1-runs and uses the same codes to the equal length runs. It also modifies the codes for 00 and 11 to improve the compression performance. Experimental results for ISCAS 89 benchmark circuits show that AFDR codes achieve higher compression ratio than FDR and other compression codes.

Quickly obtaining densely dispersed coherent particles in steel matrix and its related mechanical property

Densely distributed coherent nanoparticles(DCN)in steel matrix can enhance the work-hardening ability and ductility of steel simultaneously.All the routes to this end can be generally classified into the liquid-solid route and the solid-solid route.However,the formation of DCN structures in steel requires long processes and complex steps.So far,obtaining steel with coherent particle enhancement in a short time remains a bottleneck,and some necessary steps remain unavoidable.Here,we show a high-efficiency liquid-phase refining process reinforced by a dynamic magnetic field.Ti-Y-Mn-O particles had an average size of around(3.53±1.21)nm and can be obtained in just around 180 s.These small nanoparticles were coherent with the matrix,implying no accumulated dislocations between the particles and the steel matrix.Our findings have a potential application for improving material machining capacity,creep resistance,and radiation resistance.

An Efficient Test Data Compression Technique Based on Codes

This paper presents a new test data compression/decompression method for SoC testing,called hybrid run length codes. The method makes a full analysis of the factors which influence test parameters：compression ratio,test application time, and area overhead. To improve the compression ratio, the new method is based on variable-to-variable run length codes,and a novel algorithm is proposed to reorder the test vectors and fill the unspecified bits in the pre-processing step. With a novel on-chip decoder, low test application time and low area overhead are obtained by hybrid run length codes. Finally, an experimental comparison on ISCAS 89 benchmark circuits validates the proposed method

EFFECTS OF STRAIN RATE & TEMPERATURE ON HOT COMPRESSION FLOW BEHAVIOR OF A HYDROGENATED CAST Ti-25Al-10Nb-3V-1Mo ALLOY

The flow behavior of a cast Ti-25Al-10Nb-3V-1Mo alloy based onTi3Al, with and without hydrogen content, was investigated under isothermal compression test at strain rates of 0.1s-1 to 0.001s -1 in the temperature range of 900℃ to1000 ℃. The hot compression peak stress (or the maximum flow stress) of the alloy withand without hydrogen decreases with the increasing temperature and the decreasingstrain rate. Hydrogenation makes the hot compression peak stress decrease by 37%～53%, which corresponds to lowering the deformation temperature by about 50℃.Strain rate does not change the favorable effect of hydrogenation on hot compressionflow behavior at all three deformation temperatures. The microstructure of the alloywith 0.2% H (mass %) deformed at a fixed temperature exhibits the same feature asthat of the alloys without hydrogenation deformed at higher temperatures for bothstrain rates. Hydrogenation has the same effect on microstructure as strain rate andtemperature.

Particle simulation of the failure process of brittle rock under triaxial compression

In order to investigate the failure process of brittle rock under triaxial compression through both experimental and numerical approaches, the particle simulation method was used in numerical simulations and the simulated results were compared with those of the experiment. The numerical simulation results, such as fracture propagation, microcrack distribution, stress-strain response, and damage patterns, were discussed in detail. The simulated results under various confining pressures （0-60 MPa） are in good agreement with the experimental results. The simulated results reveal that rock failure is caused by axial splitting under uniaxial compression. As the confining pressure increases, rock failure occurs in a few localized shear planes and the rock mechanical behavior is changed from brittle to ductile. Consequently, the peak failure strength, microcrack numbers, and the shear plane angle increase, but the ratio of tensile to shear microcracks decreases. The damage formation during the compression simulations indicates that the particle simulation method can produce similar behaviors as those observed through laboratory compression tests.

Experimental study on cracking behaviour of moulded gypsum containing two non-parallel overlapping flaws under uniaxial compression

Failure of rock mass that is subjected to compressive loads occurs from initiation, propagation, and linkage of new cracks from preexisting fissures. Our research investigates the cracking behaviour and coalescence process in a brittle material with two non-parallel overlapping flaws using a high-speed camera. The coalescence tensile crack and tensile wing cracks were the first cracks to occur from the preexisting flaws. The initiation stresses of the primary cracks at the two tips of each flaw were simultaneous and decreased with reduced flaw inclination angle. The following types of coalescence cracks were identified between the flaws: primary tensile coalescence crack, tensile crack linkage, shear crack linkage, mixed tensile-shear crack, and indirect crack coalescence. Coalescence through tensile linkage occurred mostly at pre-peak stress. In contrast, coalescence through shear or mixed tensile-shear cracks occurred at higher stress. Overall, this study indicates that the geometry of preexisting flaws affect crack initiation and coalescence behaviour.

Specimen aspect ratio and progressive field strain development of sandstone under uniaxial compression by three-dimensional digital image correlation

The complete stress-strain characteristics of sandstone specimens were investigated in a series of quasistatic monotonic uniaxial compression tests.Strain patterns development during pre-and post-peak behaviours in specimens with different aspect ratios was also examined.Peak stress,post-peak portion of stress-strain,brittleness,characteristics of progressive localisation and field strain patterns development were affected at different extents by specimen aspect ratio.Strain patterns of the rocks were obtained by applying three-dimensional(3D) digital image correlation(DIC) technique.Unlike conventional strain measurement using strain gauges attached to specimen,3D DIC allowed not only measuring large strains,but more importantly,mapping the development of field strain throughout the compression test,i.e.in pre-and post-peak regimes.Field strain development in the surface of rock specimen suggests that strain starts localising progressively and develops at a lower rate in pre-peak regime.However,in post-peak regime,strains increase at different rates as local deformations take place at different extents in the vicinity and outside the localised zone.The extent of localised strains together with the rate of strain localisation is associated with the increase in rate of strength degradation.Strain localisation and local inelastic unloading outside the localised zone both feature post-peak regime.

Shape ratio effects on the mechanical characteristics of rectangular prism rocks and isolated pillars under uniaxial compression

Isolated pillars in underground mines are subjected to uniaxial stress,and the load bearing cross-section of pillars is commonly rectangularly shaped.In addition,the uniaxial compression test(UCT)is widely used for determining the basic mechanical properties of rocks and revealing the mechanism of isolated pillar disasters under unidimensional stress.The shape effects of rock mechanical properties under uniaxial compression are mainly quantitatively reflected in the specific shape ratios of rocks.Therefore,it is necessary to study the detailed shape ratio effects on the mechanical properties of rectangular prism rock specimens and isolated pillars under uniaxial compressive stress.In this study,granite,marble and sandstone rectangular prism specimens with various height to width ratios(r)and width to thickness ratios(u)were prepared and tested.The study results show that r and u have a great influence on the bearing ability of rocks,and thin or high rocks have lower uniaxial compressive strength.Reducing the level of r can enhance the u effect on the strength of rocks,and increasing the level of u can enhance the r effect on the strength of rocks.The lateral strain on the thickness side of the rock specimen is larger than that on the width side,which implies that crack growth occurs easily on the thickness side.Considering r and u,a novel strength prediction model of isolated pillars was proposed based on the testing results,and the prediction model was used for the safety assessment of 179 isolated pillars in the Xianglu Mountain Tungsten Mine.

Microstructure and compression properties of fine Al2O3 particles dispersion strengthened molybdenum alloy

The Mo alloys reinforced by Al2O3 particles were fabricated by hydrothermal synthesis and powder metallurgy. The microstructures of Mo-Al2O3 alloys were studied by using XRD, SEM and TEM. The results show that Al2O3 particles, existing as a stable hexagonal phase(α-Al2O3), are uniformly dispersed in Mo matrix. The ultrafine α-Al2O3 particles remarkably refine grain size and increase dislocation density of Mo alloys. Moreover, a good interfacial bonding zone between α-Al2O3 and Mo grain is obtained. The crystallographic orientations of the interface of the Al2O3 particles and Mo matrix are [111]a-Al2O3//[111]Mo and(112)a-Al2O3//(0 11)Mo. Due to the effect of secondary phase and dislocation strengthening, the yield strength of Mo-2.0 vol.%Al2O3 alloy annealed at 1200 ℃ is approximately 56.0% higher than that of pure Mo. The results confirm that the addition of Al2O3 particles is a promising method to improve the mechanical properties of Mo alloys.

Micro-failure process and failure mechanism of brittle rock under uniaxial compression using continuous real-time wave velocity measurement

In this study,the micro-failure process and failure mechanism of a typical brittle rock under uniaxial compression are investigated via continuous real-time measurement of wave velocities.The experimental results indicate that the evolutions of wave velocities became progressively anisotropic under uniaxial loading due to the direction-dependent development of micro-damage.A wave velocity model considering the inner anisotropic crack evolution is proposed to accurately describe the variations of wave velocities during uniaxial compression testing.Based on which,the effective elastic parameters are inferred by a transverse isotropic constitutive model,and the evolutions of the crack density are inversed using a self-consistent damage model.It is found that the propagation of axial cracks dominates the failure process of brittle rock under uniaxial loading and oblique shear cracks develop with the appearance of macrocrack.

Primary and secondary consolidation compression for saturated soil considering coupling effect of loading and heating

Geotechnical engineering that relates to the energy and environmental problem is receiving more and more attention worldwide.It is of great theoretical and practical value to study the properties of soil under thermal mechanical coupling and its mathematical description.Firstly,based on the general function,a unified primary and secondary consolidation model of saturated soil considering heating temperature is deduced.Combining the existing research achievements,a practical model is obtained which comprehensively reflects the effective stress change,creep and heating effects.After that,a series of thermo-consolidation tests are carried out using a temperature controlled consolidation instrument to study the effects of effective stress,temperature and consolidation duration on saturated soils.The corresponding functional formulas and parameters are obtained thusly.On this basis,the calculation and analysis are carried out to check the reliability and applicability of the newly proposed model.The new model is simple and practical and the parameters are easy to be obtained.And it describes the main law of consolidation compression of saturated soils under the thermal mechanical coupling effect.Therefore,it is suggested for theoretical analysis of thermal geotechnical engineering problems.

Analysis of the stress ratio of anisotropic rocks in uniaxial tests

The effect of structural discontinuities on the progressive failure process of anisotropic rocks should be paid particular attention.The crack damage stress σ_(cd),also considered as the yield strength,and the relationship between σ_(cd) and the uniaxial peak strength σ_(ucs) of anisotropic rocks for different orientations 8 of the isotropy planes with respect to the loading directions were investigated theoretically and experimentally.A theoretical relation of σ_(cd)/σ_(ucs) with the function of the shape parameter m was established.Additionally,uniaxial compression tests of shale samples were conducted for several inclinations θ.The test result of σ_(cd)/σ_(ucs) was close to the theoretical value for a given orientation.Furthermore,both experimental results and theoretical solutions of σ_(cd)/σ_(ucs) were independent of the inclination θ while σ_(cd) andσ_(ucs) were strongly affected by θ.The strength ratio σ_(cd)/σ_(ucs) may therefore be an intrinsic property of anisotropic rocks and could be used to predict the failure of rock samples.

Triaxial compression strength for artificial frozen clay with thermal gradient

A series of triaxial compression tests for frozen clay were performed by KoDCGF （freezing with non-uniform temperature under loading after K0 consolidation） method and GFC （freezing with non-uniform temperature without experiencing Ko consolidation） method at various confining pressures and thermal gradients. The experimental results indicate that the triaxial compression strength for frozen clay in KoDCGF test increases with the increase of confining pressure, but it decreases as the confining pressure increases further in GFC test. In other words, the compression strength for frozen clay with identical confining pressure decreases with the increase in thermal gradient both in KoDCGF test and GFC test. The strength of frozen clay in KoDCGF test is dependent of pore ice strength, soil particle strength and interaction between soil skeleton and pore ice. The decrease of water content and distance between soil particles leads to the decrease of pore size and the increase of contact area between particles in KoDCGF test, which further results in a higher compression strength than that in GFC test. The compression strength for frozen clay with thermal gradient can be descried by strength for frozen clay with a uniform temperature identical to the temperature at the height of specimen where the maximum tensile stress appears.

Temperature-controlled triaxial compression/creep test device for thermodynamic properties of soft sedimentary rock and corresponding theoretical prediction

In deep geological disposal of high-level nuclear waste,one of the most important subjects is to estimate long-term stability and strength of host rock under high temperature conditions caused by radioactive decay of the waste.In this paper,some experimental researches on the thermo-mechanical characteristics of soft sedimentary rock have been presented.For this reason,a new temperature-controlled triaxial compression and creep test device,operated automatically by a computer-controlled system,whose control software has been developed by the authors,was developed to conduct the thermo-mechanical tests in different thermal loading paths,including an isothermal path.The new device is proved to be able to conduct typical thermo-mechanical element tests for soft rock.The test device and the related testing method were introduced in detail.Finally,some test results have been simulated with a thermo-elasto-viscoplastic model that was also developed by the authors.

Validity of continuous-failure-state unloading triaxial tests as a means to estimate the residual strength of rocks

The residual strength of rocks and rock masses is an important parameter to be constrained for analysis and design purposes in many rock engineering applications.A residual strength envelope in principal stress space is typically developed using residual strength data obtained from compression tests on many different specimens of the same rock type.In this study,we examined the potential for use of the continuous-failure-state testing concept as a means to constrain the residual strength envelope using a limited number of specimens.Specifically,cylindrical specimens of three rock types(granodiorite,diabase,and Stanstead granite)were unloaded at the residual state such that a full residual strength envelope for each individual specimen was obtained.Using a residual strength model that introduces a single new strength parameter(the residual strength index,or RSI),the results of the continuous-failurestate unloading tests were compared to conventionally obtained residual strength envelopes.Overall,the continuous-failure-state residual strength data were found to be consistent with the conventional residual strength data.However,it was identified that the primary factor limiting an accurate characterization of the residual strength for a given rock type is not the amount of data for a given specimen,but the variety of specimens available to characterize the inherent variability of the rock unit of interest.Accordingly,the use of continuous-failure-state testing for estimation of the residual strength of a rock unit is only recommended when the number of specimens available for testing is very limited(i.e.<5).