This paper describes a method of the computer aided garment design,and discusses 3-D humanbody,wire frame modelling,approaches of expressing and a shading model of the 3-D garment.
The field of solid modeling has created numerous techniques for unambiguous computer representations of three-dimensional objects. Its data structures and algorithms have been used in a broad range of applications: Co...The field of solid modeling has created numerous techniques for unambiguous computer representations of three-dimensional objects. Its data structures and algorithms have been used in a broad range of applications: Computer-Aided Design and Computer-Aided Manufacturing (CAD/ CAM), robotics, computer vision, computer graphics and visualization, virtual reality, etc. This research paper is used to generate process plan from feature-based modeling, based on an integrated geometric modeling system that supports both feature-based modeling and information storage. Present system is developed only for milling components and limited to selective machining features for prismatic components and further implemented for more machining features to develop algorithms for modeling the components through the input of machining features. As a result, feature information is directly available to downstream activities, and feature extraction is no longer needed. The various systematic steps involved in this approach are study of Design, identification of Features, selection of Processes, Tools and Machines, Machining and Inspection [DFPTMMI]. Machining features generated in the design stage are recognized and stored under the Visual Basic control of CATIA software ActiveX interface. Algorithms are developed for individual features and these algorithms are embedded in Visual Basic forms. This system is discussed and suited for 2.5 Dimensional part approach, however, that can be extended to 3 dimensional prismatic part and complex features machining. Finally a process planning chart has been presented as a model process planning.展开更多
Stress-induced failure is among the most common causes of instability in Canadian deep underground mines.Open stoping is the most widely practiced underground excavation method in these mines,and creates large stopes ...Stress-induced failure is among the most common causes of instability in Canadian deep underground mines.Open stoping is the most widely practiced underground excavation method in these mines,and creates large stopes which are subjected to stress-induced failure.The probability of failure(POF)depends on many factors,of which the geometry of an open stope is especially important.In this study,a methodology is proposed to assess the effect of stope geometrical parameters on the POF,using numerical modelling.Different ranges for each input parameter are defined according to previous surveys on open stope geometry in a number of Canadian underground mines.A Monte-Carlo simulation technique is combined with the finite difference code FLAC3D,to generate model realizations containing stopes with different geometrical features.The probability of failure(POF)for different categories of stope geometry,is calculated by considering two modes of failure;relaxation-related gravity driven(tensile)failure and rock mass brittle failure.The individual and interactive effects of stope geometrical parameters on the POF,are analyzed using a general multi-level factorial design.Finally,mathematical optimization techniques are employed to estimate the most stable stope conditions,by determining the optimal ranges for each stope’s geometrical parameter.展开更多
Artificial bone with porous structure is crucial for tissue scaffold and clinic implants.Scaffold provides structure support for cells and guides tissues regeneration for final tissue structure.A computational aided p...Artificial bone with porous structure is crucial for tissue scaffold and clinic implants.Scaffold provides structure support for cells and guides tissues regeneration for final tissue structure.A computational aided process of porous bone modeling was developed which described the design and fabrication of tissue scaffolds by considering intricate architecture,porosity and pore size.To simulate intricate bone structure,different constructive units were presented.In modeling process,bone contour was gotten from computed tomography(CT)images and was divided into two levels.Each level was represented by relatively reconstructive process.Pore size distribution was controlled by using mesh generation.The whole hexahedral mesh was reduced by unit structure,when a 3D mesh with various hexahedral elements was provided.The simulation results show that constructive structure of porous scaffold can meet the needs of clinic implants in accurate and controlled way.展开更多
The concept of′Probe detector′is introduced in this paper with its application in geometricmodeling and graphics.In terms of the concept,the authors derive edge data from the CSG datarepresentation and establish a w...The concept of′Probe detector′is introduced in this paper with its application in geometricmodeling and graphics.In terms of the concept,the authors derive edge data from the CSG datarepresentation and establish a wireframe model.展开更多
This paper proposes a new computer aided pattern design system(CAPDS)in which a uniformmathematical expression is used to construct different objects. In the geometric model, 3 B-splineis adopted as a line model. The ...This paper proposes a new computer aided pattern design system(CAPDS)in which a uniformmathematical expression is used to construct different objects. In the geometric model, 3 B-splineis adopted as a line model. The new system with uniform mathematical expression has the distin-guishing features: curve smoothness and fidelity, convenience to process graphic data in thedatabase and etc.. This paper presents the data structure, the program structure and also the implementation.展开更多
The general computer-aided design （CAD） software cannot meet the mould design requirement of the autoclave process for composites, because many parameters such as temperature and pressure should be considered in the...The general computer-aided design （CAD） software cannot meet the mould design requirement of the autoclave process for composites, because many parameters such as temperature and pressure should be considered in the mould design process, in addition to the material and geometry of the part. A framed-mould computer-aided design system （FMCAD） used in the autoclave moulding process is proposed in this paper. A function model of the software is presented, in which influence factors such as part structure, mould structure, and process parameters are considered; a design model of the software is established using object oriented （O-O） technology to integrate the stiffness calculation, temperature field calculation, and deformation field calculation of mould in the design, and in the design model, a hybrid model of mould based on calculation feature and form feature is presented to support those calculations. A prototype system is developed, in which a mould design process wizard is built to integrate the input information, calculation, analysis, data storage, display, and design results of mould design. Finally, three design examples are used to verify the prototype.展开更多
This paper gives and verifies a mathematical model with only one argument which determines the movement parameters of any point in a plane four-bar linkage on the basis of the analysis of mining machinery linkages. C ...This paper gives and verifies a mathematical model with only one argument which determines the movement parameters of any point in a plane four-bar linkage on the basis of the analysis of mining machinery linkages. C A A (computer aided analysis) based on the mathemetical model can be used to make not only the quick and accurate analysis and design of mining machinery linkages but also the movement analysis and optimization design of any other plane four-bar linkage.展开更多
A 3-Dimensional computer aided garment design (CAGD) system has been developed andimplemented on a high-performance workstation. We studied various approaches to the func-tional modelling of garment designs for the sy...A 3-Dimensional computer aided garment design (CAGD) system has been developed andimplemented on a high-performance workstation. We studied various approaches to the func-tional modelling of garment designs for the system. According to the characteristic data of a hu-man body, the models of human body and the garment are displayed on the screen, then we canmodify the garment with various styles and different sizes. The system can transform the 3-Dgarment to the 2-D pieces. The system has improved design efficiency. Various potential alterna-tives and improvement of the system have also been studied and explored.展开更多
The reasonability of cabin layout is studied according to the ergonomic theory on micro-computer. This system includes the anthropometric model,modeling of aircraft seats and cabin,interactive ergonomic analyses on ef...The reasonability of cabin layout is studied according to the ergonomic theory on micro-computer. This system includes the anthropometric model,modeling of aircraft seats and cabin,interactive ergonomic analyses on effect.展开更多
An object oriented data modelling in computer aided design (CAD) databases is focused. Starting with the discussion of data modelling requirements for CAD applications, appropriate data modelling features are introdu...An object oriented data modelling in computer aided design (CAD) databases is focused. Starting with the discussion of data modelling requirements for CAD applications, appropriate data modelling features are introduced herewith. A feasible approach to select the “best” data model for an application is to analyze the data which has to be stored in the database. A data model is appropriate for modelling a given task if the information of the application environment can be easily mapped to the data model. Thus, the involved data are analyzed and then object oriented data model appropriate for CAD applications are derived. Based on the reviewed object oriented techniques applied in CAD, object oriented data modelling in CAD is addressed in details. At last 3D geometrical data models and implementation of their data model using the object oriented method are presented.展开更多
In the context of applying computer aided design tools to aircraft conceptualdesign, a sketch based approach is proposed to help designers turn their original concepts intocomplex numerical models that are usable for ...In the context of applying computer aided design tools to aircraft conceptualdesign, a sketch based approach is proposed to help designers turn their original concepts intocomplex numerical models that are usable for further analysis and optimization. This approachemphasizes the integration of general configuration and the layout of such components as engines,payloads, fuel tanks and landing gears, and the representation of a design scheme as uniform planesketches and three dimensional models. This paper presents the measures adopted to implement theapproach in a prototype system, including the object-oriented data structure, friendly graphicaluser interfaces and basic features of relevant modules. Several examples generated in the prototypeand applications of the results are finally outlined to illustrate the effectiveness of theapproach.展开更多
Abstract For two rational quadratic B spline curves with same control vertexes, the cross ratio of four collinear points are represented: which are any one of the vertexes, and the two points that the ray initialing f...Abstract For two rational quadratic B spline curves with same control vertexes, the cross ratio of four collinear points are represented: which are any one of the vertexes, and the two points that the ray initialing from the vertex intersects with the corresponding segments of the two curves, and the point the ray intersecting with the connecting line between the two neighboring vertexes. Different from rational quadratic Bézier curves, the value is generally related with the location of the ray, and the necessary and sufficient condition of the ratio being independent of the ray's location is showed. Also another cross ratio of the following four collinear points are suggested, i.e. one vertex, the points that the ray from the initial vertex intersects respectively with the curve segment, the line connecting the segments end points, and the line connecting the two neighboring vertexes. This cross ratio is concerned only with the ray's location, but not with the weights of the curve. Furthermore, the cross ratio is projective invariant under the projective transformation between the two segments.展开更多
文摘This paper describes a method of the computer aided garment design,and discusses 3-D humanbody,wire frame modelling,approaches of expressing and a shading model of the 3-D garment.
文摘The field of solid modeling has created numerous techniques for unambiguous computer representations of three-dimensional objects. Its data structures and algorithms have been used in a broad range of applications: Computer-Aided Design and Computer-Aided Manufacturing (CAD/ CAM), robotics, computer vision, computer graphics and visualization, virtual reality, etc. This research paper is used to generate process plan from feature-based modeling, based on an integrated geometric modeling system that supports both feature-based modeling and information storage. Present system is developed only for milling components and limited to selective machining features for prismatic components and further implemented for more machining features to develop algorithms for modeling the components through the input of machining features. As a result, feature information is directly available to downstream activities, and feature extraction is no longer needed. The various systematic steps involved in this approach are study of Design, identification of Features, selection of Processes, Tools and Machines, Machining and Inspection [DFPTMMI]. Machining features generated in the design stage are recognized and stored under the Visual Basic control of CATIA software ActiveX interface. Algorithms are developed for individual features and these algorithms are embedded in Visual Basic forms. This system is discussed and suited for 2.5 Dimensional part approach, however, that can be extended to 3 dimensional prismatic part and complex features machining. Finally a process planning chart has been presented as a model process planning.
基金funded by a grant from Natural Sciences and Engineering Research Council of Canada (NSERC)the authors would like to acknowledge the Niobec mine (Saint-Honoré, QuébecQuébec)
文摘Stress-induced failure is among the most common causes of instability in Canadian deep underground mines.Open stoping is the most widely practiced underground excavation method in these mines,and creates large stopes which are subjected to stress-induced failure.The probability of failure(POF)depends on many factors,of which the geometry of an open stope is especially important.In this study,a methodology is proposed to assess the effect of stope geometrical parameters on the POF,using numerical modelling.Different ranges for each input parameter are defined according to previous surveys on open stope geometry in a number of Canadian underground mines.A Monte-Carlo simulation technique is combined with the finite difference code FLAC3D,to generate model realizations containing stopes with different geometrical features.The probability of failure(POF)for different categories of stope geometry,is calculated by considering two modes of failure;relaxation-related gravity driven(tensile)failure and rock mass brittle failure.The individual and interactive effects of stope geometrical parameters on the POF,are analyzed using a general multi-level factorial design.Finally,mathematical optimization techniques are employed to estimate the most stable stope conditions,by determining the optimal ranges for each stope’s geometrical parameter.
基金Project(2011DFB70230)supported by State International Cooperation Program of ChinaProject(N110403003)supported by Basic Research Foundation of Education Ministry of China
文摘Artificial bone with porous structure is crucial for tissue scaffold and clinic implants.Scaffold provides structure support for cells and guides tissues regeneration for final tissue structure.A computational aided process of porous bone modeling was developed which described the design and fabrication of tissue scaffolds by considering intricate architecture,porosity and pore size.To simulate intricate bone structure,different constructive units were presented.In modeling process,bone contour was gotten from computed tomography(CT)images and was divided into two levels.Each level was represented by relatively reconstructive process.Pore size distribution was controlled by using mesh generation.The whole hexahedral mesh was reduced by unit structure,when a 3D mesh with various hexahedral elements was provided.The simulation results show that constructive structure of porous scaffold can meet the needs of clinic implants in accurate and controlled way.
文摘The concept of′Probe detector′is introduced in this paper with its application in geometricmodeling and graphics.In terms of the concept,the authors derive edge data from the CSG datarepresentation and establish a wireframe model.
文摘This paper proposes a new computer aided pattern design system(CAPDS)in which a uniformmathematical expression is used to construct different objects. In the geometric model, 3 B-splineis adopted as a line model. The new system with uniform mathematical expression has the distin-guishing features: curve smoothness and fidelity, convenience to process graphic data in thedatabase and etc.. This paper presents the data structure, the program structure and also the implementation.
文摘The general computer-aided design （CAD） software cannot meet the mould design requirement of the autoclave process for composites, because many parameters such as temperature and pressure should be considered in the mould design process, in addition to the material and geometry of the part. A framed-mould computer-aided design system （FMCAD） used in the autoclave moulding process is proposed in this paper. A function model of the software is presented, in which influence factors such as part structure, mould structure, and process parameters are considered; a design model of the software is established using object oriented （O-O） technology to integrate the stiffness calculation, temperature field calculation, and deformation field calculation of mould in the design, and in the design model, a hybrid model of mould based on calculation feature and form feature is presented to support those calculations. A prototype system is developed, in which a mould design process wizard is built to integrate the input information, calculation, analysis, data storage, display, and design results of mould design. Finally, three design examples are used to verify the prototype.
文摘This paper gives and verifies a mathematical model with only one argument which determines the movement parameters of any point in a plane four-bar linkage on the basis of the analysis of mining machinery linkages. C A A (computer aided analysis) based on the mathemetical model can be used to make not only the quick and accurate analysis and design of mining machinery linkages but also the movement analysis and optimization design of any other plane four-bar linkage.
文摘A 3-Dimensional computer aided garment design (CAGD) system has been developed andimplemented on a high-performance workstation. We studied various approaches to the func-tional modelling of garment designs for the system. According to the characteristic data of a hu-man body, the models of human body and the garment are displayed on the screen, then we canmodify the garment with various styles and different sizes. The system can transform the 3-Dgarment to the 2-D pieces. The system has improved design efficiency. Various potential alterna-tives and improvement of the system have also been studied and explored.
文摘The reasonability of cabin layout is studied according to the ergonomic theory on micro-computer. This system includes the anthropometric model,modeling of aircraft seats and cabin,interactive ergonomic analyses on effect.
文摘An object oriented data modelling in computer aided design (CAD) databases is focused. Starting with the discussion of data modelling requirements for CAD applications, appropriate data modelling features are introduced herewith. A feasible approach to select the “best” data model for an application is to analyze the data which has to be stored in the database. A data model is appropriate for modelling a given task if the information of the application environment can be easily mapped to the data model. Thus, the involved data are analyzed and then object oriented data model appropriate for CAD applications are derived. Based on the reviewed object oriented techniques applied in CAD, object oriented data modelling in CAD is addressed in details. At last 3D geometrical data models and implementation of their data model using the object oriented method are presented.
文摘In the context of applying computer aided design tools to aircraft conceptualdesign, a sketch based approach is proposed to help designers turn their original concepts intocomplex numerical models that are usable for further analysis and optimization. This approachemphasizes the integration of general configuration and the layout of such components as engines,payloads, fuel tanks and landing gears, and the representation of a design scheme as uniform planesketches and three dimensional models. This paper presents the measures adopted to implement theapproach in a prototype system, including the object-oriented data structure, friendly graphicaluser interfaces and basic features of relevant modules. Several examples generated in the prototypeand applications of the results are finally outlined to illustrate the effectiveness of theapproach.
文摘Abstract For two rational quadratic B spline curves with same control vertexes, the cross ratio of four collinear points are represented: which are any one of the vertexes, and the two points that the ray initialing from the vertex intersects with the corresponding segments of the two curves, and the point the ray intersecting with the connecting line between the two neighboring vertexes. Different from rational quadratic Bézier curves, the value is generally related with the location of the ray, and the necessary and sufficient condition of the ratio being independent of the ray's location is showed. Also another cross ratio of the following four collinear points are suggested, i.e. one vertex, the points that the ray from the initial vertex intersects respectively with the curve segment, the line connecting the segments end points, and the line connecting the two neighboring vertexes. This cross ratio is concerned only with the ray's location, but not with the weights of the curve. Furthermore, the cross ratio is projective invariant under the projective transformation between the two segments.
