Analysis of debris flow control effect and hazard assessment in Xinqiao Gully,Wenchuan M_(s)8.0 earthquake area based on numerical simulation

Xinqiao Gully is located in the area of the 2008 Wenchuan M_(s)8.0 earthquake in Sichuan province,China.Based on the investigation of the 2023"6-26"Xinqiao Gully debris flow event,this study assessed the effectiveness of the debris flow control project and evaluated the debris flow hazards.Through field investigation and numerical simulation methods,the indicators of flow intensity reduction rate and storage capacity fullness were proposed to quantify the effectiveness of the engineering measures in the debris flow event.The simulation results show that the debris flow control project reduced the flow intensity by41.05%to 64.61%.The storage capacity of the dam decreases gradually from upstream to the mouth of the gully,thus effectively intercepting and controlling the debris flow.By evaluating the debris flow of different recurrence intervals,further measures are recommended for managing debris flow events.

An intelligent control method based on artificial neural network for numerical flight simulation of the basic finner projectile with pitching maneuver

In this paper,an intelligent control method applying on numerical virtual flight is proposed.The proposed algorithm is verified and evaluated by combining with the case of the basic finner projectile model and shows a good application prospect.Firstly,a numerical virtual flight simulation model based on overlapping dynamic mesh technology is constructed.In order to verify the accuracy of the dynamic grid technology and the calculation of unsteady flow,a numerical simulation of the basic finner projectile without control is carried out.The simulation results are in good agreement with the experiment data which shows that the algorithm used in this paper can also be used in the design and evaluation of the intelligent controller in the numerical virtual flight simulation.Secondly,combined with the real-time control requirements of aerodynamic,attitude and displacement parameters of the projectile during the flight process,the numerical simulations of the basic finner projectile’s pitch channel are carried out under the traditional PID(Proportional-Integral-Derivative)control strategy and the intelligent PID control strategy respectively.The intelligent PID controller based on BP(Back Propagation)neural network can realize online learning and self-optimization of control parameters according to the acquired real-time flight parameters.Compared with the traditional PID controller,the concerned control variable overshoot,rise time,transition time and steady state error and other performance indicators have been greatly improved,and the higher the learning efficiency or the inertia coefficient,the faster the system,the larger the overshoot,and the smaller the stability error.The intelligent control method applying on numerical virtual flight is capable of solving the complicated unsteady motion and flow with the intelligent PID control strategy and has a strong promotion to engineering application.

Numerical Investigation of Thermal Behavior of CNC Machine Tool and Its Effects on Dimensional Accuracy of Machined Parts

The dimensional accuracy of machined parts is strongly influenced by the thermal behavior of machine tools (MT). Minimizing this influence represents a key objective for any modern manufacturing industry. Thermally induced positioning error compensation remains the most effective and practical method in this context. However, the efficiency of the compensation process depends on the quality of the model used to predict the thermal errors. The model should consistently reflect the relationships between temperature distribution in the MT structure and thermally induced positioning errors. A judicious choice of the number and location of temperature sensitive points to represent heat distribution is a key factor for robust thermal error modeling. Therefore, in this paper, the temperature sensitive points are selected following a structured thermomechanical analysis carried out to evaluate the effects of various temperature gradients on MT structure deformation intensity. The MT thermal behavior is first modeled using finite element method and validated by various experimentally measured temperature fields using temperature sensors and thermal imaging. MT Thermal behavior validation shows a maximum error of less than 10% when comparing the numerical estimations with the experimental results even under changing operation conditions. The numerical model is used through several series of simulations carried out using varied working condition to explore possible relationships between temperature distribution and thermal deformation characteristics to select the most appropriate temperature sensitive points that will be considered for building an empirical prediction model for thermal errors as function of MT thermal state. Validation tests achieved using an artificial neural network based simplified model confirmed the efficiency of the proposed temperature sensitive points allowing the prediction of the thermally induced errors with an accuracy greater than 90%.

Java Language for Numerical Control Simulation System Research

Java language is widely used in a variety of development platforms to develop all kinds of application software for its simple and efficient.The programming language owning platform independent is adopted to solve the image flicker,sound loading and other issues by the threading technology,multimedia technology,graphics and point by point comparison techniques.Dynamic real⁃time process simulation is implemented and a two⁃dimensional network of CNC machining simulation system is developed while Java applet application is as a carrier.The simulation results show that the system has a friendly interface and fast calculation speed,and platform portability has a certain practicality and application value.

Effect of geometrical parameters on forming quality of high-strength TA18 titanium alloy tube in numerical control bending

The forming quality of high-strength TA18 titanium alloy tube during numerical control bending in changing bending angle β, relative bending radius R/D and tube sizes such as diameter D and wall thickness t was clarified by finite element simulation. The results show that the distribution of wall thickness change ratio Δt and cross section deformation ratio ΔD are very similar under different β; the Δt and ΔD decrease with the increase of R/D, and to obtain the qualified bent tube, the R/D must be greater than 2.0; the wall thinning ratio Δto slightly increases with larger D and t, while the wall thickening ratio Δti and ΔD increase with the larger D and smaller t; the Δto and ΔD firstly decrease and then increase, while the Δti increases, for the same D/t with the increase of D and t.

METHOD FOR SUPPRESSING CUTTING CHATTER IN NUMERICAL CONTROL MACHINE TOOLS

A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC machine tool is established. It includes the mechanical system, the servo system and the cutting chatter system. Interactions between every two systems are shown in the model. The cutting system stability is simulated and relation curves between the limited cutting width and servo system parameters are described in the experiment. Simulation and experimental results show that there is a mapping relation between the limited cutting width and servo parameters of the NC machine tool, and the method is applicable and credible to suppress chatter.

基于CNC系统的数控车床故障诊断方法

数控车床在现代制造业中扮演着重要角色,其故障诊断对于保障生产效率至关重要。提出一种基于计算机数控(Computer Numerical Control,CNC)系统的数控车床故障诊断方法,通过运行参数采集、数据预处理、特征提取和支持向量机算法,实现故障模式的智能识别。实验结果表明,该方法在故障检出率、误报率、诊断时间和准确率等方面均优于传统方法,为数控车床的智能化维护提供了新的思路,有助于提高设备的可靠性和生产效率。

Performance analysis model for real-time Ethernet-based computer numerical control system

In order to optimize the embedded system implementation for Ethernet-based computer numerical control （CNC） system, it is very necessary to establish the performance analysis model and further adopt the codesign method from the control, communication and computing perspectives. On the basis of analyzing real-time Ethemet, system architecture, time characteristic parameters of control-loop ere, a performance analysis model for real-time Ethemet-based CNC system was proposed, which is able to include the timing effects caused by the implementation platform in the simulation. The key for establishing the model is accomplished by designing the error analysis module and the controller nodes. Under the restraint of CPU resource and communication bandwidth, the experiment with a case study was conducted, and the results show that if the deadline miss ratio of data packets is 0.2%, then the percentage error is 1.105%. The proposed model can be used at several stages of CNC system development.

Shaking table test and numerical analysis of offshore wind turbine tower systems controlled by TLCD

A wind turbine system equipped with a tuned liquid column damper （TLCD） is comprehensively studied via shaking table tests using a 1/13-scaled model. The effects of wind and wave actions are considered by inputting response- equivalent accelerations on the shaking table. The test results show that the control effect of the TLCD system is significant in reducing the responses under both wind-wave equivalent loads and ground motions, but obviously varies for different inputs, Further, a blade-hub-tower integrated numerical model for the wind turbine system is established. The model is capable of considering the rotational effect of blades by combining Kane＇s equation with the finite element method. The responses of the wind tower equipped with TLCD devices are numerically obtained and compared to the test results, showing that under both controlled and uncontrolled conditions with and without blades＇ rotation, the corresponding responses exhibit good agreement. This demonstrates that the proposed numerical model performs well in capturing the wind-wave coupled response of the offshore wind turbine systems under control. Both numerical and experimental results show that the TLCD system can significantly reduce the structural response and thus improve the safety and serviceability of the offshore wind turbine tower systems. Additional issues that require further study are discussed.

Numerical modelling of structural controls on fluid flow and mineralization

This paper presents the results of a set of numerical models focussing on structural controls on hydrothermal mineralization. We first give an overview of natural phenomena of structurally-controlled ore formation and the background theory and mechanisms for such controls. We then provide the results of a group of simple 2D numerical models validated through comparison with Cu-vein structure observed near the Shilu Copper deposit （Yangchun, Guangdong Province, China） and finally a case study of 3D numerical modelling applied to the Hodgkinson Province in North Queensland （Australia）. Two modelling approaches, discrete deformation modelling and continuum coupled deformation and fluid flow modelling, are involved. The 2D model-derived patterns are remarkably consistent with the Cu-vein structure from the Shilu Copper deposit, and show that both modelling approaches can realistically simulate the mechanical behaviours of shear and dilatant fractures. The continuum coupled deformation and fluid flow model indicates that pattern of the Cu- veins near the Shilu deposit is the result of shear strain localization, development of dilation and fluid focussing into the dilatant fracture segments. The 3D case-study models （with deformation and fluid flow coupling） on the Hodgkinson Province generated a number of potential gold mineralization

Underground ground control monitoring and interpretation,and numerical modeling, and shield capacity design

Mine or longwall panel layout is a 3D structure with highly non-uniform stress distribution. Recognition of such fact will facilitate underground problem identification/investigation and solving by numerical modeling through proper model construction. Due to its versatility, numerical modeling is the most popular method for ground control design and problem solving. However numerical modeling results require highly experienced professionals to interpret its validity/applicability to actual mining operations due to complicated mining and geological conditions. Underground ground control monitoring is routinely performed to predict roof behavior such as weighting and weighting interval without matching observation of face mining condition while the mining pressures are being monitored, resulting in unrealistic interpretation of the obtained data on mining pressure. The importance of ground control pressure monitoring and simultaneous observation of mining and geological conditions is illustrated by an example of shield leg pressure monitoring and interpretation in an U.S. longwall coal mine: it was found that the roof strata act like a plate, not an individual block of the size of a shield dimension, as commonly assumed by all researchers and shield capacity is not a fixed property for a longwall panel or a mine or a coal seam. A new mechanism on the interaction between shield's hydraulic leg pressure and roof strata for shield loading is proposed.

NUMERICAL SOLUTION OF VISCOUS FLOW PAST A SOLID SPHERE WITH THE CONTROL VOLUME FORMULATION

The control volume formulation with the QUICK finite difference scheme is used to solveincompressible liquid flow past a solid sphere in terms of stream function and vorticity.Several tech-nical points are addressed on improving the accuracy and efficiency of numerical simulation of similarproblems of fluid flow.In particular,the importance of suitable specification of the distortion func-tion to enforcing the far field boundarv conditions is emphasized.

NOVEL STRUCTURE FOR DISTRIBUTED NUMERICAL CONTROL

Because of an unexpected signal noise within the network or an unpredictedfault with personal computers (PCs), many problems emerge in the implementation of distributednumerical control (DNC) with PCs-based network. To solve the problems, an industrial solution ofinvolving the field-bus technology in DNC communicating area is provided. A kind of advancedField-bus, named controller area network (CAN), is originally developed to support cheap and rathersimple automotive applications. However, because of its good performance and low cost, it is alsobeing considered in automated-manufacturing and process control environments to interconnectintelligent devices, such as modem sensors and actuators. Recently it creates a new role for CANBusin DNC that brings new thinking to DNC. CAN is used as the network platform for connecting machinetools to share information with each other reliably. Additionally, thanks to also applying of'plug-in' technology and a special interface of hardware, this solution exhibits some highcompatibility with different pedigree numerical control (NC) systems, such as Fanuc, Siemens,Cincinnati and so on. In order to improve CANBus for DNC application, a communicating competitionmodel of the basic CAN protocol, called CC model, is then highlighted. This model is able to satisfythe requirements that different machine tools share the communicating bandwidth fairly when theyrun concurrently. Finally the novel view of the latest advancement in CANBus-based DNC incombination with the manufacturing paradigm is also presented.

A Numerical-analytic Method for Quickly Predicting Springback of Numerical Control Bending of Thin-walled Tube

Springback is one of important factors influencing the forming quality of numerical control （NC） bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process was put forward. The method is based on springback angle model derived using analytic method and simulation results from three-dimensional （3D） rigid-plastic finite element method （FEM）. The method is validated through comparison with experimental results. The features of the method are as follows： （1） The method is high in efficiency because it combines advantages of rigid-plastic FEM and analytic method. （2） The method is satisfactory in accuracy, since the field variables used in the model is resulting from 3D rigid-plastic FEM solution, and the effects both of axial force and strain neutral axis shift have been included. （3） Research on multi-factor effects can be carried out using the method due to its advantage inheriting from rigid-plastic FEM. The method described here is also of general significance to other bending processes.

A Windows bitmap-based numerically controlled sculpture method and its application

Bitmap （BMP） is a widely used format in image processing. With the combination of the digital image processing and computer numerically controlled （NC） techniques, we developed a bitmap-based NC single-step and multi-dot method. An example was provided to illustrate the application and principle of this bitmap-based method in our newly innovated sandblasting glass NC sculpture system.

Numerical study on cavitation in a globe control valve with different numbers of anti-cavitation trims

Cavitation is a destructive phenomenon in control valves.In order to delay cavitation,a multi-series of perforated cylindrical plates,called trims,are used.Previously,the effects of orifice diameter and different types of trims have been investigated.In this study,by numerical analysis,a globe control valve was investigated by employing four different cases(without trim,with one trim,with two and three trims)and the impact of the number of these trims on the intensity,formation region and the initiation point of cavitation was analyzed.It was found that the addition of one stage or two stages of trims reduces the intensity and delays the onset of cavitation,relative to the valve without trim.However,no significant differences in terms of intensity and initiation point of cavitation were observed in the cases where two or three trims were used.Therefore,due to the high cost of producing the trims,and the severe drop in flow coefficient,it is not economically and technically justified to increase the number of trims to more than three.

Mathematical model for the thermal process of controlled cooling of wires and its numerical simulation

The mathematical model for the thermal process of billets rolling has beenestablished, including transporting in air and temperature-holding cover, descaling withhigh-pressure water, and the process of rolling and cooling in water box. The calculated data by themodel have been compared with the measured data and the results show that the model is right andcreditable. Based on the model, the main thermal characters of rolling line have been simulated andthe influence of all the parameters on the temperature of rolling has been analyzed.

Deformation behaviors of 21-6-9 stainless steel tube numerical control bending under different friction conditions

For contact dominated numerical control(NC) bending process of tube, the effect of friction on bending deformation behaviors should be focused on to achieve precision bending forming. A three dimensional(3D) elastic-plastic finite element(FE) model of NC bending process was established under ABAQUS/Explicit platform, and its reliability was validated by the experiment. Then, numerical study on bending deformation behaviors under different frictions between tube and various dies was explored from multiple aspects such as wrinkling, wall thickness change and cross section deformation. The results show that the large friction of wiper die-tube reduces the wrinkling wave ratio η and cross section deformation degree ΔD and increases the wall thinning degree Δt. The large friction of mandrel-tube causes large η, Δt and ΔD, and the onset of wrinkling near clamp die. The large friction of pressure die-tube reduces Δt and ΔD, and the friction on this interface has little effect on η. The large friction of bending die-tube reduces η and ΔD, and the friction on this interface has little effect on Δt. The reasonable friction coefficients on wiper die-tube, mandrel-tube, pressure die-tube and bending die-tube of 21-6-9(0Cr21Ni6Mn9N) stainless steel tube in NC bending are 0.05-0.15, 0.05-0.15, 0.25-0.35 and 0.25-0.35, respectively. The results can provide a guideline for applying the friction conditions to establish the robust bending environment for stable and precise bending deformation of tube bending.

NUMERICAL SIMULATION OF MOLTEN POOL AND CONTROL STRATEGY OF KISS POINT IN A TWIN-ROLL STRIP CASTING PROCESS

Coupled turbulent flow, temperature fields of the twin-roll casting strip process were simulated by three-dimensional finite element method. Based on the heat balance calculation and using inverse methods between the simulations and real experiments, the relational models among casting speed, location, and coefficient of heat transfer between molten metal and rolls in different regions are given. In the simulation, the calculated surface temperatures are in good agreement with the measured values. An on-line model of kiss point is derived by simulations and the geometry of molten pool, corresponding control strategy is also proposed.

Bayesian networks modeling for thermal error of numerical control machine tools

The interaction between the heat source location, its intensity, thermal expansion coefficient, the machine system configuration and the running environment creates complex thermal behavior of a machine tool, and also makes thermal error prediction difficult. To address this issue, a novel prediction method for machine tool thermal error based on Bayesian networks (BNs) was presented. The method described causal relationships of factors inducing thermal deformation by graph theory and estimated the thermal error by Bayesian statistical techniques. Due to the effective combination of domain knowledge and sampled data, the BN method could adapt to the change of running state of machine, and obtain satisfactory prediction accuracy. Ex- periments on spindle thermal deformation were conducted to evaluate the modeling performance. Experimental results indicate that the BN method performs far better than the least squares (LS) analysis in terms of modeling estimation accuracy.