Peeling behavior and spalling resistance of CFRP sheets bonded to bent concrete surfaces

In this paper, the peeling behavior and the spalling resistance effect of carbon fiber reinforced polymer （CFRP） sheets externally bonded to bent concrete surfaces are firstly investigated experimentally. Twenty one curved specimens and seven plane specimens are studied in the paper, in which curved specimens with bonded CFRP sheets can simulate the concrete spalling in tunnel, culvert, arch bridge etc., whereas plane specimens with bonded CFRP sheets can simulate the concrete spalling in beam bridge, slab bridge and pedestrian bridge. Three kinds of curved specimens with different radii of curvature are chosen by referring to practical tunnel structures, and plane specimens are used for comparison with curved ones. A peeling load is applied on the FRP sheet by loading a circular steel tube placed into the central notch of beam to debond CFRP sheets from the bent concrete surface, meanwhile full-range load-deflection curves are recorded by a MTS 831.10 Elastomer Test System. Based on the experimental results, a theoretical analysis is also conducted for the specimens. Both theoretical and experimental results show that only two material parameters, the interfacial fracture energy of CFRP-concrete interface and the tensile stiffness of CFRP sheets, are needed for describing the interfacial spalling behavior. It is found that the radius of curvature has remarkable influence on peeling load-deflection curves. The test methods and test results given in the paper are helpful and available for reference to the designer of tunnel strengthening.

Effect of Rubber Particle Modifi cation on Properties of Rubberized Concrete

To improve the combination of cement matrix and waste tire rubber particles in concrete, the rubber particles were treated with acrylic acid（ACA） and polyethylene glycol（PEG） for grafting hydrophilic groups on their surfaces. The X-Ray photoelectron spectroscopy（XPS） and surface contact angle were used to characterize the hydrophilicity and surface functional group of rubber particles. The effect of rubber particle modifi cation on fresh/hardened properties of rubberized concrete was studied. The experimental results show that the contact angle between rubber particle surface and water decreases when rubber particle is modifi ed. Compared with the unmodifi ed rubberized concrete（RC）, the unit weight of modifi ed rubberized concrete（MRC） changes slightly. However, the slump, air-entrainment, compressive strength, flexural strength, and impact performance of MRC are obviously improved. Under good condition of slump, the water-cement ratio of the MRC can be reduced from 0.4 to 0.38. And the compressive strength and fl exural strength of the MRC（10% rubber particle content） can be increased by 25.9% and 26.4%, respectively.

Resistivity-temperature Characteristics of Conductive Asphalt Concrete

The changes of resistivity of conductive asphalt concrete at different temperatures were studied,and positive temperature coefficient（PTC）modelwas established to estimate the influence of temperature on the resistivity quantitatively,which eliminated the interference with conductivity evaluation brought by temperature variation.Finally,the analysis of temperature cycling test results proves that the changes of percolation network structure caused by temperature variation prompt the emergence of PTC of conductive asphalt concrete.

Hydration Process and Crack Tendency of Concrete Based on Resistivity and Restrained Shrinkage Crack

Hydration process, crack potential and setting time of concrete grade C30, C40 and C50 were monitored by using a non-contact electrical resistivity apparatus, a novel plastic ring mould and penetration resistance methods, respectively. The results show the highest resistivity of C30 at the early stage until a point when C50 accelerated and overtook the others. It has been experimentally confirmed that the crossing point of C30 and C50 corresponds to the final setting time of C50. From resistivity derivative curve, four different stages were observed upon which the hydration process is classified; these are dissolution, induction, acceleration and deceleration periods. Consequently, restrained shrinkage crack and setting time results demonstrated that C50 set and cracked the earliest. The cracking time of all the samples occurred within a reasonable experimental period thus the novel plastic ring is a convenient method for predicting concrete＇s crack potential. The highest inflection time（t_i） obtained from resistivity curve and the final setting time（t_f） were used with crack time（t_c） in coming up with mathematical models for the prediction of concrete＇s cracking age for the range of concrete grade considered. Finally, an ANSYS numerical simulation supports the experimental findings in terms of the earliest crack age of C50 and the crack location.