A characteristic curve-based numerical framework for predicting strength of multi-bolted composite joints subjected to hygrothermal condition

Many works have been made for predicting the failure of composite joints.However,there is still lack of method for multi-bolted composite joints subjected to the hygrothermal environment.In this work,a characteristic curve-based numerical framework is proposed,which includes two main steps and shows low computational cost.Firstly,a 3D finite element model considering hygrothermal effects is established to analyze the bolt-load distribution of multi-bolted joints.Secondly,a new characteristic curve considering the hygrothermal influence is used to obtain the failure pattern and strength of composite joints.The two-,three-and four-bolted composite joints with-55℃/dry(CTD),23℃/dry(RTD)and 70℃/wet(ETW)conditions are investigated.The test outcomes present good agreement with predicted results,which illustrates the effectiveness and applicability of the proposed method.Meanwhile,it is shown that the environmental condition affects the bolt-load ratio slightly,but does not change the location of the key loaded hole.Furthermore,deviations of the strengths in CTD and ETW conditions are about 5%and-16%from that in the RTD condition,respectively.The environmental condition does not affect the failure modes of two-and three-bolted joints,whereas changes the failure mode of the four-bolted joint.The proposed method is efficient,reliable and needs only linear elastic FE analysis,making it applicable for engineering practice.

Geological conditions and reservoir characteristics of various shales in major shalehosted regions of China

China is home to shales of three facies:Marine shale,continental shale,and marine-continental transitional shale.Different types of shale gas are associated with significantly different formation conditions and major controlling factors.This study compared the geological characteristics of various shales and analyzed the influences of different parameters on the formation and accumulation of shale gas.In general,shales in China’s several regions exhibit high total organic carbon(TOC)contents,which lays a sound material basis for shale gas generation.Marine strata generally show high degrees of thermal evolution.In contrast,continental shales manifest low degrees of thermal evolution,necessitating focusing on areas with relatively high degrees of thermal evolution in the process of shale gas surveys for these shales.The shales of the Wufeng and Silurian formations constitute the most favorable shale gas reservoirs since they exhibit the highest porosity among the three types of shales.These shales are followed by those in the Niutitang and Longtan formations.In contrast,the shales of the Doushantuo,Yanchang,and Qingshankou formations manifest low porosities.Furthermore,the shales of the Wufeng and Longmaxi formations exhibit high brittle mineral contents.Despite a low siliceous mineral content,the shales of the Doushantuo Formation feature a high carbonate mineral content,which can increase the shales’brittleness to some extent.For marine-continental transitional shales,where thin interbeds of tight sandstone with unequal thicknesses are generally found,it is recommended that fracturing combined with drainage of multiple sets of lithologic strata should be employed to enhance their shale gas production.

Characteristics of In-Situ Soil Water Hysteresis Observed through Multiple-Years Monitoring

A soil water retention curve (SWRC) is an essential soil physical property for analyzing transport and retention of water in a soil layer. A SWRC is often described as a single-valued function that relates the soil water potential ψ to volumetric water content θ of the soil. However, an in-situ ψ − θ relation should show soil water hysteresis, though this fact is often neglected in analyses of field soil water regimes while long-term in-situ soil water hysteresis is not well characterized. This study aimed at probing and characterizing in-situ ψ − θ relations. The developments of large hysteresis in the in-situ ψ − θ relations were observed only a few times during the study period of 82 months. Any of the large hysteretic behaviors in the ψ − θ relations began with an unusually strong continual reduction in ψ. The completion of a hysteresis loop required a recorded maximum rainfall. Because the study field had very small chances to meet such strong rainfall events, it took multiple years to restore the fraction of soil water depleted by the unusually strong continual reduction in ψ. While wetting-drying cycles had occurred within a certain domain of ψ, hysteretic behaviors tended to be so small that the in-situ ψ − θ relation can be approximated as a single-valued function of θ(ψ). These observed patterns of the in-situ ψ − θ relations were characterized by kinds of difference in dθ/dψ between a drying process and a wetting process at a given ψ. Thus, more amounts of experimental facts about wetting SWRCs in parallel with drying SWRCs should be needed for correct modelling, analyzing, and predicting soil water regimes in fields. It is also necessary to increase our understandings about the long-term trends of occurrences of extreme weather conditions associated with possible change in climate.

Enrichment conditions and distribution characteristics of lacustrine medium-to-high maturity shale oil in China

Successful breakthroughs have been made in shale oil exploration in several lacustrine basins in China,indicating a promising future for shale oil exploration and production.Current exploration results have revealed the following major conditions of lacustrine shale oil accumulation:(1)stable and widely distributed shale with a high organic abundance and appropriate thermal maturity acts as a fundamental basis for shale oil retention.This shale exhibits several critical parameters,such as total organic carbon content greater than 2%,with optimal values ranging from 3% to 4%,kerogen Ⅰ and Ⅱ_(1) as the dominant organic matter types,and vitrinite reflectance(R_(o))values greater than 0.9%(0.8% for brackish water environments).(2)Various types of reservoirs exhibiting brittleness and a certain volume of micro-nanoscale pores are critical conditions for shale oil accumulation,and these reservoirs have porosities greater than 3% to 6%.Moreover,when diagenesis is incipient,pure shales are not favorable for medium-to-high maturity shale oil enrichment,whereas tight sandstone and hybrid rocks with clay content less than 20% are favorable;however,for medium-to-late-stage diagenesis,pure shales with a clay content of 40% are favorable.(3)The retention of a large amount of high-quality hydrocarbons is the factor that best guarantees shale oil accumulation with good mobility.Free hydrocarbon content exceeding a threshold value of 2 mg/g is generally required,and the optimum value is 4 mg/g to 6 mg/g.Moreover,a gas-oil ratio exceeding a threshold value of 80 m^(3)/m^(3) is required,with the optimal value ranging from 150 m^(3)/m^(3) to 300 m^(3)/m^(3).(4)High-quality roof and floor sealing conditions are essential for the shale oil enrichment interval to maintain the overpressure and retain a sufficient amount of hydrocarbons with good quality.Lacustrine shale oil distributions exhibit the following characteristics:(1)major enrichment areas of shale oil are located in semi-deep to deep lacustrine depositional areas with external materials,such as volcanic ash fallout,hydrothermal solutions,and radioactive substances with catalytic action,as inputs;(2)intervals with“four high values and one preservation condition”govern the distribution of shale oil enrichment intervals;and(3)favorable assemblages of lithofacies/lithologies determine the distribution of enrichment area.According to preliminary estimates,China has 131×10^(8) to 163×10^(8) t of total shale oil resources with medium-to-high thermal maturity,among which 67×10^(8) to 84×10^(8) t is commercial.These resources are primarily located in the Chang 7^(1+2) interval in the Ordos Basin,Qing 1+2 members in Gulong sag in the Songliao Basin,Kongdian and Shahejie formations of Cangdong sag,Qikou sag and the Jiyang depression in the Bohai Bay Basin,and Lucaogou Formation in the Junggar Basin.

Effects of Different Ecological Conditions on Grain Quality and RVA Profile Characteristics of Japonica Rice Varieties from Yunnan Plateau of China and Korea

[Objective] This study aimed to investigate the variation characteristics of Yunnan and Korean japonica rice quality under different environmental conditions in Yunnan Plateau. [Method] Ten Yunnan japonica rice varieties and six Korean japonica rice varieties were selected to investigate the effects of ecological conditions on grain quality characteristics and starch RVA profile characteristic values of Yunnan and Korean japonica rice. [Result] The coefficient of variation of Yunnan and Korean japonica rice reached the maximum in setback viscosity (SBV). The coefficients of variation of brown rice length (BRL), chalkiness rate (CR), amylose content (AC), protein content (PC), alkali digestion value (ADV), final viscosity (FLV), setback viscosity (SBV) and peak time (PeT) of Yunnan japonica rice varieties were significantly higher than those of Korean japonica rice, while other grain quality characteristics were contrary. With the increasing altitudes, BRL, brown rice width (BRW), length-width ratio (L/W), whiteness (WH), AC, ADV, FLV and consistence viscosity (CTV) of Yunnan japonica rice and BRL, BRW, WH, PC, peak viscosity (PKV), hot viscosity (HTV) and breakdown viscosity (BDV) of Korean japonica rice were significantly reduced , while CR, PC, HTV and PeT of Yunnan japonica rice and L/W, AC, ADV and CTV of Korean japonica rice significantly increased, but CR of Korean japonica rice showed no significantly variation. PKV, BDV and pasting temperature (PaT) of Yunnan japonica rice and PaT of Korean japonica rice showed an upward trend after an initial drop with the increasing altitudes, while SBV of Yunnan japonica rice and FLV and PeT of Korean japonica rice were contrary. [Conclusion] This study provided theoretical basis for breeding of japonica rice in Yunnan Plateau.

Modeling of fine coal flotation separation based on particle characteristics and hydrodynamic conditions

Flotation is a complex multifaceted process that is widely used for the separation of finely ground minerals. The theory of froth flotation is complex and is not completely understood. This fact has been brought many monitoring challenges in a coal processing plant. To solve those challenges, it is important to understand the effect of different parameters on the fine particle separation, and control flotation performance for a particular system. This study is going to indicate the effect of various parameters （particle Characteristics and hydrodynamic conditions） on coal flotation responses （flotation rate constant and recovery） by different modeling techniques. A comprehensive coal flotation database was prepared for the statistical and soft computing methods. Statistical factors were used for variable selections. Results were in a good agreement with recent theoretical flotation investigations. Computational models accurately can estimate flotation rate constant and coal recovery （correlation coefficient 0.85, and 0.99, respectively）. According to the results, it can be concluded that the soft computing models can overcome the complexity of process and be used as an expert system to control, and optimize parameters of coal flotation process.

Nonlinear Dynamic Characteristics of the Vectored Thruster AUV in Complex Sea Conditions

The mobility of the vectored thruster AUV in different environment is the important premise of control system design. The new type of autonomous underwater vehicle (AUV) equipped with rudders and vectored thrusters which are combined to control the course is studied. Firstly, Euler angles representation and quaternion method are applied to establish six-DOF kinematic model respectively, then Newton second law and Lagrangian approach are used to deduce the vectored thruster AUV’s nonlinear dynamic equations with six degrees of freedom (DOF) respectively in complex sea conditions based on the random wave theory according to the structural and kinetic characteristics of the vectored thruster AUV in this paper. The kinematic models and dynamic models based on different theories have the same expression and conclusion, which shows that the kinematic models and dynamic models of the vectored thruster AUV are accurate. The Runge-Kutta arithmetic is used to solve the dynamic equations, which not only can simulate the motions such as cruise and hover but also can describe the vehicle’s low-frequency and high-frequency motion. The results of computation show that the mobility of the vectored thruster AUV in interference-free environment and the integrated signals including low-frequency motion signal and high-frequency motion signal in environmental disturbance accord with practical situation, which not only solve the problem of especial singularities when the pitch angle θ = ±90° but also clears up the difficulties of computation and display of the coupled nonlinear motion equations in complex sea conditions. Moreover, the high maneuverability of the vectored thruster AUV equipped with rudders and vectored thrusters is validated, which lays a foundation for the control system design.

Influence of heat treatment conditions on bending characteristics of 6063 aluminum alloy sheets

Bending deformation behaviors of solution treated(ST),natural aged(NA)and T6tempered6063aluminum alloy sheetswere studied by three-point bending tests.The changes of bending force,interior angle,bending radius and sheet thickness in thefillet region were analyzed by experimental measurements and numerical simulations.The results showed that the bendingcharacteristics were strongly dependent on the heat treatment conditions.The T6alloy sheets were bent more sharply and localplastic deformation occurred severely in the fillet region.However,the ST and NA alloy sheets exhibited relatively uniform bendingdeformation and large bending radius.The bending force of T6alloy was the highest,followed by the NA alloy and that of the STalloy was minimum.After unloading,as compared with the ST and NA alloys,the springback of T6alloys was markedly larger.Theaging time showed a positive sensitivity on the springback and non-uniform bending deformability.The bending characteristics areattributed to the combined effects of yield strength,yield ratio and coefficient of neutral layer.

Biological characteristics of marine bacterium S-9801 strain and its culture conditions of pigment production

Strain of Flavobacterium sp.(S-9801),was screened from 207 strains of marine bacteria isolated from the Bohai Sea continental shelf and the Zhujiang Estuary,for its red pigment production.The biological characteristics of strain S-9801 and culture conditions of pigment production have been checked out in this study. The color of the bacterial colony on 2216E medium was from coccineus to rose bengal. Optimum culture conditions were sodium chloride concentration(g/dm3),10～30;pH,3～8;temperature,25～28℃;tryptone and yeast extract as nitrogen sources and glucose as carbon source. Under optimum conditions,pigment accumulation started after 12 h,reaching a maximum rate of synthesis at 36 h.

Experimental Study on Combustion Characteristics of Pulverized Coal under Enriched-oxygen Condition by Entrained Flow Reactor

Four different pulverized coals have been used to study the effects of oxygen concentration on combustion characteristics under different enriched-oxygen conditions by entrained flow reactor experiments. The results show that: with the increase of oxygen concentration, the ignition temperature of four coals greatly decreases and the low volatile coals decrease faster; with the increase of oxygen concentration, the ignition mode of pulverized coal has an obviously transformation from homogeneous ignition to heterogeneous ignition, and the corresponding oxygen concentrations are about 40% and 50%-60% respectively for bituminous coal and lignite, and both about 30% for lean coal and anthracite; with the increase of oxygen concentration, the optimal pulverized coal concentrations of bituminous coal and lignite increase firstly and then decrease, but for lean coal and anthracite, the optimal pulverized coal concentrations decrease slowly with the increase of oxygen concentration.

Germination Characteristics of Hordeum brevisubulatum Seeds in Different Conditions

[ Objective] To study the germination characteristics of Hordeum brevisubulatum seeds in the Songnen Plains of China under different conditions and find out the optimum conditions for germination. [ Method] A total of five variable temperatures including 15/25, 20/30, 15/30, 20/25 and 15/20 ℃, five concentrations of sodium chloride solutions including 0, 75, 85, 95 and 105 mmol/L, and five concentrations of CS2 strain （the A values were 0, 0.500 0, 0.050 0, 0.005 0 and 0.000 5, respectively） were studied by orthogonal experimental design. [ Result] The germination rate, germination energy and germination index were significantly （ P 〈 0.05） affected by the temperature and sodium chloride concentration, but rarely affected by the CS2 strain concentration. Moreover, the germination rate, germination potential and germination index were all decreased with the increasing of sodium chloride concentration. [ Conclusion] The optimal germination conditions of Hordeum brevisubulatum are as follows： temperatures of 15/25 ℃ and 15/30℃, 0 mmoVL of sodium chloride concentration.

Geometrical and Geotechnical Characteristics of Landslides in Korea under Various Geological Conditions

The goal of this study is to determine the geometrical and geotechnical characteristics of landslides under various geological conditions using detailed field surveys, laboratory soil tests and precipitation records. Three study areas are selected to consider different rocks, including gneiss in Jangheung, granite in Sangju and sedimentary rocks in Pohang, South Korea. Many landslides have occurred in these three areas during the rainy season.Precipitation records indicate that landslides occurring in the gneiss area of Jangheung and granite area of Sangju may be influenced by the hourly rainfall intensity rather than cumulative rainfall.However, landslides occurring in the sedimentary rock area of Pohang may be influenced by hourly rainfall intensity and cumulative rainfall. To investigate the factors that influence these types of landslides, a detailed landslide survey was performed and a series of laboratory soil tests were conducted.According to the detailed field survey, most landslides occurred on the flanks of mountain slopes, and the slope inclination where they occurred mostly ranged from 26 to 30 degrees, regardless of the geological conditions. The landslide in the gneiss area of Jangheung is larger than the landslides in the granite area of Sangju and sedimentary rock area of Pohang.Particularly, the landslide in the sedimentary rock area is shorter and shallower than the landslides in the gneiss and granite areas. Thus, the shape and size of the landslide are clearly related to the geological conditions. According to the integrated soil property and landslide occurrence analyses results, the average dry unit weight of the soils from the landslide sites is smaller than that of the soils obtained from the nonlandslide site. The average coefficient of permeability of soils obtained from the landslide sites is greater than that of soils obtained from the non-landslide sites with the same geology. These results indicate that the soils from the landslide sites are more poorly graded or looser than the soils from the non-landslide sites.

Tribological characteristics of C/C-SiC braking composites under dry and wet conditions

C/C-SiC braking composites,based on reinforcement of carbon fibers and matrices of carbon and silicon carbide,were fabricated by warm compaction and in situ reaction process.The tribological characteristics of C/C-SiC braking composites under dry and wet conditions were investigated by means of MM-1000 type of friction testing machine.The influence of dry and wet conditions on the tribological characteristics of the C/C-SiC composites was ascertained.Under dry condition,C/C-SiC braking composites show superior tribological characteristics,including high coefficient of friction (0.38),good abrasive resistance (thickness loss is 1.10 μm per cycle) and steady breaking.The main wear mechanism is plastic deformation and abrasion caused by plough.Under wet condition,frictional films form on the worn surface.The coefficient of friction (0.35) could maintain mostly,and the thickness loss (0.70 μm per cycle) reduces to a certain extent.Furthermore,braking curves are steady and adhesion and oxidation are the main wear mechanisms.

Quantizing Analysis and Processing of Test Conditions for Infantry Grenade Ignition Characteristics

A rule of how the ignition probability or invalidation probability of infantry grenade varies with the projectile quantity is presented based on the statistical analysis. The statistical induction, quantizing analysis and data processing in the infantry grenade type approval test are completed, and we obtain how various test factors in the research item affect the test results(invalidation probability), i.e., quantized data. The acquisition of these quantized data provides theory basis and data auspice for further reasonable filtration of all test factors and the optimization of test scheme.

Below-ground growth characteristics of 13-year-old Pinus densiflora on different contour conditions in a post-fire plantation in Samcheuk,Korea

We estimated the growth volume of artificially reforested Pinus densiflora in a post-fire area on three different contour conditions by comparing and analyzing the vertical and horizontal distributions of below-ground roots on each contour. The main roots at the south-facing slope (SS) developed in a long and straight form, and those on the north-facing slope (NS) in a twisted form. The side roots developed more than the main roots on the Ridge. The depth of taproots decreased in the following order: SS > NS > Ridge. The roots on the SS developed in a pile-form root structure whereas those in the Ridge and NS developed concentrically near the root collar. The amount of root development decreased in the following order: SS > NS > Ridge. The ratio of fine roots from the whole-root development decreased in the following order: Ridge > SS > NS. These results can guide considerations of growth differences according to the planting contour conditions for future establishment of P. densiflora artificial plantations.

A new type of micro-disseminated gold deposits in association with diabase found in Yunnan and Guizhou provinces and Guangxi Zhuang Autonomous Region——Their geological characteristics and metallogenic conditions

With the continuous development of gold ore prospecting and exploration in recent years a new type of micro-disseminated gold deposits have been found in the regions of Southwest Guizhou Province and Northwest Guangxi Zhuang Autonomous Region,with the orebodies directly occurring in diabase or in the contact zone between diabase and strata.The orebodies are strictly controlled by fault structures.The discovery of this type of gold deposits has brought about new prospects for gold ore prospecting in the Yunnan-Guizhou-Guangxi Golden Triangle region.From the preliminary analysis of the geological characteristics of the Qiaoxiang gold deposit in Wangmo County,in combination with the results of research work in the adjacent areas in recent years,this paper roughly described the geological characteristics and metallogenic conditions of this type of gold ore deposits with an attempt to make more and more geologists pay enough attention to this type of gold ore deposits,so as to promote gold ore prospecting in Guizhou Province to develop toward a variety of types of gold deposits in all round way.

Comparison of Flow Characteristics Around Refractive and Right-angled Groins in Barotropic and Baroclinic Conditions

Groins are employed to prevent nearshore areas from erosion and to control the direction of flow. However, the groin structure and its associated flow characteristics are the main causes of local erosion. In this study, we investigate the flow patterns around refractive and right-angle groins. In particular, we analytically compare the flow characteristics around a refractive groin and study the degree of accuracy that can be achieved by using a right-angle groin of various projected lengths. To compare the flow characteristics, we replaced the right-angle groin with an approximation of a refractive groin. This replacement had the least effect on the maximum velocity of flow in the channel. Moreover, we investigated the distribution of the density variables of temperature and salinity, and their effects on the flow characteristics around the right-angle groin. A comparison of the flow analysis results in baroclinic and barotropic conditions reveals that the flow characteristic values are very similar for both the refractive and right-angle groins. The geometry of the groin, i.e., right-angle or refractive, has little effect on the maximum speed to relative average speed. Apart from the angular separation, the arm length of the groin in downstream refractive groins has less effect on other flow characteristics than do upstream refractive groins. We also correlated a number of non-dimensional variables with respect to various flow characteristics and groin geometry. These comparisons indicate that the correlation between the thalweg height and width of the channel and groin arm＇s length to projection length have been approximated using linear and nonlinear formulas regardless of inner velocity in the subcritical flow.

Characteristics and Meteorological Conditions of Ozone Pollution in Shantou City

Based on routine monitoring data of air quality and meteorological data in Shantou City during 2015-2019,temporal-spatial variation characteristics of O 3 pollution and its correlation with meteorological conditions in Shantou City were explored.The research results showed that O 3 pollution days in Shantou City showed an increasing trend year by year,and O 3 pollution had far-distance transportation and the development trend from offshore Nan ao Island to urban district.In spring and autumn,there was serious O 3 pollution,and it was the most prominent in October.Its diurnal variation in O 3 pollution days was mainly wide-peak type in the afternoon,showing as that O 3 concentration declined slowly after the noon.In O 3 pollution days,higher O 3 concentration was easy to appear at night,causing that O 3 peak in the second day was uplifted,and there was continuous O 3 pollution.Combining backward trajectory analysis chart,it was found that Shantou was mainly affected by coastal transport of northerly polluted air mass,and it was transported into Shantou City from the east to the northeast.O 3 from long-distance transmission superimposed with locally generated O 3,which commonly pushed up the level of O 3 concentration.The weather of O 3 pollution in Shantou City had the characteristics of high temperature and low humidity.There was 25-30℃of temperature interval and 46%-60%of relative humidity interval,and it was accompanied by grade-2 easterly wind.

Different Growth Characteristics of Grewia mollis, Grewia tenax and Grewia villosa Under Nursery and Field Conditions

This study was carried out to assess the growth characteristics of Grewia moll＆, Grewia tenax and Grewia villosa under the nursery and field conditions. Two experiments were conducted at the farm of the College of Natural Resources and Environmental Studies, University of Juba, Khartoum, Sudan. Randomized complete block design with three replications was used. Morphological and physiological factors were measured. Seedlings height, number of leaves, number of branches and sub-branches were different （P 〈 0.05） among the three species at the nursery stage and under field conditions. Collar diameter showed significant difference among the species under field conditions. Physiological factors exhibited more significant variations in the field than at the nursery stage. Variations in growth characteristics were attributed to genetics differences and different growth habit, while variations in physiological factors （photosynthesis and transpiration rate） were attributed to differences in leaf structure, size and number of stomatal pores.

Biomass growth characteristics of 13-year-old Pinus densiflora S.et Z.in a post-fire plantation on different contour conditions in Samcheuk,Korea

We used preliminary data to estimate the growth volume of artificially reforested Pinus densiflora in a post-fire area on three different contour conditions. We compared the growth of P. densiflora on a south-facing slope(Ssth), north-facing slope(Snth) and ridge area(Ridge), using 7 trees selected from each stand aspect. The tree height, diameter and growth volume were measured and the dry weight of each plant part were compared and analyzed. The results revealed that the total dry weight was highest on Ssth(5992.3 g), followed by Snth(4833.2 g) and lowest on Ridge(3160.1 g). The height growth was highest on Snth(285.8 cm), followed by Ssth(274.5 cm) and lowest on Ridge(211.5 cm). The diameter growth was greatest on Ssth(7.37 cm), followed by Snth(7.10 cm) and lowest on Ridge(5.72 cm). The volume growth was highest on Ssth(4257.7 cm3), followed by Snth(3750.7 cm3) and lowest on Ridge(2093.7 cm3). Therefore, we should consider and include the concept of slope orientation together with differences in habitat environments in afforestation projects when creating artificial forests with P. densiflora. These study results can serve as important preliminary data for future establishment of artificial forest of P. densiflora in a post-fire plantation.