Analysis of Reservoir Forming Conditions and Prediction of Continuous Tight Gas Reservoirs for the Deep Jurassic in the Eastern Kuqa Depression,Tarim Basin

The exploration targets in the Kuqa Depression at present are mainly structure traps in Cretaceous-Tertiary.Due to the complexity of mountain distribution and reservoir forming conditions, the exploration of Jurassic in the eastern Kuqa Depression has been in a state of semi-stagnation since the discovery of the Yinan-2 gas reservoir.According to the concept and theory of 'continuous petroleum reservoirs' and the re-analysis of the forming conditions of the Yinan-2 gas reservoir and regional natural gas in the eastern Kuqa Depression,it is believed that the deep Jurassic has good natural gas accumulation conditions as well as geological conditions for forming continuous tight gas reservoirs.The boundary of the Yinan-2 gas reservoir is not controlled by a structural spillpoint.The downdip part of the structure is dominated by gas,while the hanging wall of the fault is filled by water and forming obvious inverted gas and water.The gas reservoir has the normal temperature and ultrahigh pressure which formed in the near source or inner-source.All of these characteristics indicate that the Yinan-2 gas reservoir is different from conventional gas reservoirs.The deep Jurassic in the eastern Kuqa Depression has multisets of source-reservoir-cap assemblages,which comprise interbedded sandstones and mudstones.These assemblages are characterized by a self-generation,self-preserving and self-coverage model.Reservoir sandstones and coal measure mudstones are interbedded with each other at a large scale.As the source rocks,Triassic-Jurassic coal measure mudstones distribute continuously at a large scale and can generate and expel hydrocarbon.Source rocks contact intimately with the overlying sandstone reservoirs.During the late stage of hydrocarbon expulsion,natural gas charged continuously and directly into the neighboring reservoirs.Petroleum migrated mainly in a vertical direction over short distances.With ultra-high pressure and strong charging intensity,natural gas accumulated continuously.Reservoirs are dominated by sandstones of braided delta facies.The sand bodies distribute continuously horizontal.With low porosity and low permeability,the reservoirs are featured by strong heterogeneity.It is hypothesized that the sandstones of the interior depression tend to be relatively tight with increasing depth and structure stress weakness.Thus,it is predicted that continuous tight gas reservoirs of ultra-high pressure may exist in the deep formations of the eastern and even the whole Kuqa Depression.So,it is worth evaluating the exploration potential.

The influence of temperature,pressure,salinity and capillary force on the formation of methane hydrate

We present here a thermodynamic model for predicting multi-phase equilibrium of methane hydrate liquid and vapor phases under conditions of different temperature, pressure, salinity and pore sizes. The model is based on the 1959 van der Waals--Platteeuw model, angle-dependent ab initio intermolecular potentials, the DMW-92 equation of state and Pitzer theory. Comparison with all available experimental data shows that this model can accurately predict the effects of temperature, pressure, salinity and capillary radius on the formation and dissociation of methane hydrate. Online calculations of the p-T conditions for the formation of methane hydrate at given salinities and pore sizes of sediments are available on： www.geochem-model.org/models.htm.

Forming Condition and Geology Prediction Techniques of Deep Clastic Reservoirs

1 Introduction As new exploration domain for oil and gas,reservoirs with low porosity and low permeability have become a hotspot in recent years(Li Daopin,1997).With the improvement of technology,low porosity and low

Studies of Metallic and Trace Minerals of the Tiegelongnan Cu-Au Deposit, Central Tibet, China

Electron probe micro-analysis(EPMA) and scanning electron microscopy(SEM) equipped with energy dispersive spectrometry(EDS) have been used to investigate the principal ore minerals and coexisting metallic mineral inclusions in polished thin sections from the Tiegelongnan deposit, which consists of a high-sulfidation epithermal system(HSES) and a porphyry system(PS). Molybdenite,chalcopyrite, bornite, tennantite, enargite, digenite, anilite, covellite, and tetrahedrite have been identified by EPMA. Intergrowth, cross-cutting and replacement relationships between the metallic minerals suggest that molybdenite formed first(stage 1),followed by chalcopyrite ± bornite ± hematite(stage 2),then bornite ± Cu-sulfides ± Cu-Fe-sulfoarsenides(stage 3),and lastly Cu-Fe-sulfoarsenides ±Cu-sulfides(stage 4). Pyrite is developed throughout all the stages. Droplet-like inclusions of Au-Te minerals commonly occur in tennantite but not in the other major sulfides(molybdenite, chalcopyrite and bornite),implying that tennantite is the most important Au telluride carrier. The pervasive binary equilibrium phases of calaverite and altaite constrain fin the range from ～-6.5 to ～-8 and f<-11.The intergrowth of bornite and chalcopyrite and the conversion from bornite to digenite suggest fluctuated and relatively low precipitation temperature conditions in the HSES relative to the PS.Contrastingly, the dominance of chalcopyrite in the PS, with minor bornite, suggests relatively high temperature conditions. These new results are important for further understanding the mineral formation processes superimposed by HSES and PS systems.

Bulging in incremental sheet forming of cold bonded multi-layered Cu clad sheet: Influence of forming conditions and bending

Bulge is a defect that causes geometrical inaccuracy and premature failure in the innovative incremental sheet forming (ISF) process. This study has two-fold objectives:(1) knowing the bulging behavior of a Cu clad tri-layered steel sheet as a function of forming conditions, and (2) analyzing the bending effect on bulging in an attempt to identify the associated mechanism. A series of ISF tests and bending analysis are performed to realize these objectives. From the cause-effect analysis, it is found that bulge formation in the layered sheet is sensitive to forming conditions in a way that bulging can be minimized utilizing annealed material and performing ISF with larger tool diameter and step size. The bending under tension analysis reveals that the formation of bulge is an outgrowth of bending moment that the forming tool applies on the sheet during ISF. Furthermore, the magnitude of bending moment depending upon the forming conditions varies from 0.046 to 10.24 N·m/m and causes a corresponding change in the mean bulge height from 0.07 to 0.91 mm. The bending moment governs bulging in layered sheet through a linear law. These findings lead to a conclusion that the bulge defect can be overcome by controlling the bending moment and the formula proposed can be helpful in this regards.

Primary Discussion on the Characteristics and Forecasting Methods of Dense Fog in Xuzhou City

[Objective] The study aimed to discuss the characteristics and forecasting methods of dense fog in Xuzhou City. [Method] Based on the data of dense fog in Xuzhou City from 1960 to 2009, the characteristics and forming conditions of dense fog in the region were analyzed, and then its forecasting methods were introduced, finally corresponding disaster prevention measures were put forward. [ Result] Dense fog might ap- pear in each season, its frequency of occurrence was the highest in December, namely 16.4% ; it was the lowest in June （2.2%）, and the fog las- ted for a short time and was thin. Heavy fog occurred more frequently in winter half year than summer half year, and the frequency of occurrence from October to next February was about 66.7%. In addition, dense fog mostly generated from late midnight to morning, while it appeared less in the afternoon. It shows that dense fog in Xuzhou City is mainly radiation fog instead of advection fog, but the two kinds of fog appeared simultane- ously sometimes. [ Conclusion] The research could provide scientific forecasting methods for the precise prediction of dense fog in Xuzhou City.

The Analysis on Comparison of Forming Condition with Abroad Palaeo-Epicontinental Marine Basin and Possibility of Potash Formation in North China

1 Introduction Currently,all six different continents have discovered potash deposits and potash-bearing salt lake saline water.However,the distribution is extremely uneven,which is mostly concentrated in Canada,Russia,Middle-Asia and

Effect of Deformation Condition on Axial Compressive Precision Forming Process of Tube with Curling Die

The effect of the deformation condition on the axial compressive precision forming process of tube with curling die was investigated by using a rigid-plastic FEM. The results show that the forming accuracy depends mainly on geometric condition rp/d0, little on tube material properties and friction condition; the relative gap △/2rp of double-walled tubes obtained decreases with Increasing rp/d0, and there is a parameter k for a given to/do or rp/t0, when rp/d0 >k, △/2rp< 1, otherwise △/2rp>1.

UBM STUDY ON DOUBLE-DIE IRONING PROCESS

The double-die ironing process is studied by means of UBM. The formulas of deformation load.contact stress on die surface, and tensile stress which acts on workpiece is obtained. Taking account of dirnensional accuracy, a new critical condition of limit reduction in cross section area is put forward for the flrst time. The test experiment indicats that results of theoretical analysis well accord with the actual conditions.[0]

Forming conditions of blisters during solution heat treatment of Al–Si alloy semi-solid die castings

In the present study,numerical simulation method was used to analyze the conditions,resulting in the formation of blisters during solution heat treatment.Blister formation is considered to occur as the height of blister reaches 5μm.The effects of process parameters on the magnitude of the forming temperatures of blister(Tb)were discussed.Two kinds of Al-Si alloys were used to analyze the effect of mechanical properties of the alloys on blister forming conditions.Simulation results show that decreasing the initial pressure in gas hole,the long-short axial ratio of gas hole and the size of gas hole,as well as increasing the depth of gas hole and the strength of alloy are helpful to increase the critical temperature of forming blister.These conclusions are helpful for casters to understand the conditions controlling blister formation during solution heat treatment and take actions to avoid the blister defects.

Effects of Forming Conditions and TiC–TiB_2 Contents on the Microstructures of Self-Propagating High-Temperature Synthesized NiAl–TiC–TiB_2 Composites

The NiAl–TiC–TiB2 composites were processed by self-propagating high-temperature synthesis（SHS） method using raw powders of Ni, Al, Ti, B4 C, TiC, and TiB2, and their microstructure and micro-hardness were investigated. The TiC–TiB2 in NiAl matrix, with contents from 10 to 30 wt%, emerged with the use of two methods： in situ formed and externally added. The results show that all final products are composed of three phases of NiAl, TiC, and TiB2. The microstructures of NiAl–TiC–TiB2 composites with in situ-formed TiC and TiB2 are fine, and all the three phases are distributed uniformly. The grains of NiAl matrix in the composites have been greatly refined, and the micro-hardness of NiAl increases from 381 HV100 to 779 HV100. However, the microstructures of NiAl–TiC–TiB2 composites with externally added TiC and TiB2 are coarse and inhomogeneous, with severe agglomeration of TiC and TiB2 particles. The samples containing externally added 30 wt% TiC–TiB2attain the micro-hardness of 485 HV100. The microstructure evolution and fracture mode of the two kinds of NiAl–TiC–TiB2 composites are different.

NECESSARY AND SUFFICIENT CONDITIONS FOR THE EXISTENCE OF LIAPUNOV FUNCTION OF LUR'E FORM WITH■≤0

This paper is concerned with the problem of absolute stability for a control system with severalexecutive elements. Necessary and sufficient conditions are obtained for the existence of Liapunovfunction of Lur'e form with negative semi--definite derivative (i.e. V≤0).