A study of pulsed high voltage driven hollow-cathode electron beam sources through synchronous optical trigger

In this study,a pulsed,high voltage driven hollow-cathode electron beam sources through an optical trigger is designed with characteristics of simple structure,low cost,and easy triggering.To validate the new design,the characteristics of hollow-cathode discharge and electron beam characterization under pulsed high voltage drive are studied experimentally and discussed by discharge characteristics and analyses of waveform details,respectively.The validation experiments indicate that the pulsed high voltage supply significantly improves the frequency and stability of the discharge,which provides a new solution for the realization of a high-frequency,high-energy electron beam source.The peak current amplitude in the high-energy electron beam increases from 6.2 A to 79.6 A,which indicates the pulsed power mode significantly improves the electron beam performance.Besides,increasing the capacitance significantly affects the highcurrent,lower-energy electron beam more than the high-energy electron beam.

Online Learning Control for Harmonics Reduction Based on Current Controlled Voltage Source Power Inverters

Nonlinear loads in the power distribution system cause non-sinusoidal currents and voltages with harmonic components.Shunt active filters(SAF) with current controlled voltage source inverters(CCVSI) are usually used to obtain balanced and sinusoidal source currents by injecting compensation currents.However,CCVSI with traditional controllers have a limited transient and steady state performance.In this paper,we propose an adaptive dynamic programming(ADP) controller with online learning capability to improve transient response and harmonics.The proposed controller works alongside existing proportional integral(PI) controllers to efficiently track the reference currents in the d-q domain.It can generate adaptive control actions to compensate the PI controller.The proposed system was simulated under different nonlinear(three-phase full wave rectifier) load conditions.The performance of the proposed approach was compared with the traditional approach.We have also included the simulation results without connecting the traditional PI control based power inverter for reference comparison.The online learning based ADP controller not only reduced average total harmonic distortion by 18.41%,but also outperformed traditional PI controllers during transients.

Recent Developments of Modulation and Control for High-Power Current-Source-Converters Fed Electric Machine Systems

The pulse-width-modulated(PWM)current-source converters(CSCs)fed electric machine systems can be considered as a type of high reliability energy conversion systems,since they work with the long-life DC-link inductor and offer high fault-tolerant capability for short-circuit faults.Besides,they provide motor friendly waveforms and four-quadrant operation ability.Therefore,they are suitable for high-power applications of fans,pumps,compressors and wind power generation.The purpose of this paper is to comprehensively review recent developments of key technologies on modulation and control of high-power(HP)PWM-CSC fed electric machines systems,including reduction of low-order current harmonics,suppression of inductor–capacitor(LC)resonance,mitigation of common-mode voltage(CMV)and control of modular PWM-CSC fed systems.In particular,recent work on the overlapping effects during commutation,LC resonance suppression under fault-tolerant operation and collaboration of modular PMW-CSCs are described.Both theoretical analysis and some results in simulations and experiments are presented.Finally,a brief discussion regarding the future trend of the HP CSC fed electric machines systems is presented.

Multilevel Current Source Converters for High Power Medium Voltage Applications

In medium voltage high power applications,multi-level current source converters(CSCs)are good candidate to increase system power region,reliability,and the quality of output waveforms.Compared with widely researched voltage source multi-level converters(MLCs),the current source MLCs have the advantages of inherent short-circuit protection,high power capability and high quality of output current waveforms.The main features of MLCs include reduced harmonics,lower switching frequency and reduced current stress on each device which is a particularly important for high power application with low voltage and high current requirements.This paper conducts a general review of the current research about MLCs in higher power medium voltage application.The different types of parallel structure based MLCs and the modulation methodologies will be introduced and compared.Specifically,the circuit analysis of the common-mode(CM)loop for parallel structures will be conducted,the common-mode voltage(CMV)and circulating current suppression methods developed on the base of multilevel modulations will be addressed.

A Comparison of Control Methods for Z-Source Inverter

In recent years, Z-source inverters (ZSI) have been proposed as an replacement power conversion concept which it has both voltage buck and boost abilities. In addition, ZSI doesn’t require dead-time to protection short circuit at two switches any of the same phase leg in the inverter bridge and to achieve optimal harmonic of current, voltage. This paper presents two different control methods (CM) for ZSI. The aim of this study to compare between two modulation methods, there are modi?ed space vector pulse width modulation method (MSVM) and the simple boost control (SBC) about the unique harmonic performance features, the total average and peak switching device power of the inverter system. In addition, this paper also analyzes about the ability exceed modulation index in linear region of two CM using MATLAB/Simulink.

Very Low Power,Low Voltage,High Accuracy,and High Performance Current Mirror

A novel low power and low voltage current mirror with a very low current copy error is presented and the principle of its operation is discussed. In this circuit, the gain boosting regulated cascode scheme is used to improve the output resistance, while using inverter as an amplifier. The simulation results with HSPICE in TSMC 0.18 μm CMOS technology are given, which verify the high performance of the proposed structure. Simulation results show an input resistance of 0.014 Ω and an output resistance of 3 GΩ. The current copy error is favorable as low as 0.002% together with an input （the minimum input voltage of Vin,min- 0.24 V） and an output （the minimum output voltage of Vout,min~ 0.16 V） compliances while working with the 1 V power supply and the 50 μA input current. The current copy error is near zero at the input current of 27 μA. It consumes only 76μW and introduces a very low output offset current of 50 pA.

Inherently Sinusoidal Single-phase Voltage Source Inverter Based on Modified Cuk Cell

Renewable energy has become important for electricity generation because of the high air pollution associated with conventional fossil-based energy systems.Conventional fossil-based power plants are gradually transitioning by incorporating renewable energy sources,such as photovoltaic(PV)cells.In a PV system,an inverter converts DC power from solar panels to AC power required to serve common electrical loads.A conventional H-bridge inverter topology has several disadvantages,such as the voltage being not sinusoidal,switching the DC voltage and high common-mode voltage.The common-mode voltage can cause a large leaked capacitive current,which can result in undesirable operation in solar power applications.A common solution to this problem is the addition of a large filter to the input or output of an inverter.An inherent sinusoidal voltage source inverter based on a modified Cuk converter as its basic cell,which simultaneously generates a sinusoidal output voltage and a lower common-mode voltage,is proposed.The proposed topology does not require additional input or output filters.Analytical expressions are derived to confirm the operation of the proposed topology.Simulation results confirm the mathematical analysis.A laboratory-scale experiment is performed to verify the proposed inverter.

Comparative Methodical Assessment of Established MOSFET Threshold Voltage Extraction Methods at 10-nm Technology Node

Threshold voltage (VTH) is the most evocative aspect of MOSFET operation. It is the crucial device constraint to model on-off transition characteristics. Precise VTH value of the device is extracted and evaluated by several estimation techniques. However, these assessed values of VTH diverge from the exact values due to various short channel effects (SCEs) and non-idealities present in the device. Numerous prevalent VTH extraction methods are discussed. All the results are verified by extensive 2-D TCAD simulation and confirmed through analytical results at 10-nm technology node. Aim of this research paper is to explore and present a comparative study of largely applied threshold extraction methods for bulk driven nano-MOSFETs especially at 10-nm technology node along with various sub 45-nm technology nodes. Application of the threshold extraction methods to implement noise analysis is briefly presented to infer the most appropriate extraction method at nanometer technology nodes.

Three Phase Dual Input Direct Matrix Converter for Integration of Two AC Sources from Wind Turbines

This project proposes a novel dual-input matrix converter (DIMC) which is used to integrate the output of the wind energy to a power grid. The proposed matrix converter is developed based on the traditional indirect matrix converter under reverse power flow operation mode, but with its six-switch voltage source converter replaced by a nine-switch configuration followed by the current source inverter (CSI). Matrix electric power conversion topologies and their switch functions are flexible and are used for specific applications. With the additional three switches, the proposed DIMC can provide six input terminals, which make it possible to integrate two independent AC sources from two independent wind turbines into a single grid tied power electronics interface. Commanded currents can be extracted from the two input sources to the grid. The proposed PI control and modulation schemes guaranteed sinusoidal input and output waveforms as well as reduced THD. The simulation results are provided to validate the effectiveness of the proposed control and modulation schemes for the proposed converter.

计及采样扰动抑制的电压源逆变器三矢量无模型预测电流控制方法

针对传统电压源逆变器无模型预测电流控制(model-free predictive current control,MFPCC)方法存在电流纹波大、电流梯度更新停滞以及预测性能易受采样扰动影响的问题。该文提出一种计及采样扰动的三矢量MFPCC方法。在一个控制周期应用3个基本矢量,并根据价值函数计算矢量作用时间,降低了输出电流纹波;其次,通过建立不同矢量作用下的电流梯度方程组,实现电流梯度数据的实时更新,消除了停滞现象;再次,分析采样扰动对MFPCC的影响,采用扩张状态观测器估计采样扰动以补偿预测电流控制,抑制其对输出电流的影响。最后,通过仿真和实验,对所提方法的有效性进行了验证。

模块化高压大容量DC/DC变换器综述

随着新能源发电占比增加和电网规模的不断扩大,直流输电系统的容量不断提升,含有不同电压等级的直流电网是未来发展的必然趋势。在此背景下,DC/DC变换器作为直流电网关键设备,在多电压等级互联场景中发挥着重要作用。文中首先对已有的模块化高压大容量DC/DC变换器进行归纳、分类和比较,然后阐述了目前模块化高压大容量DC/DC变换器的拓扑结构、工作原理与特点,并针对其特点提出了不同变换器的适用场景,最后对未来的研究方向提出了建议。

R&D and application of voltage sourced converter based high voltage direct current engineering technology in China

As a new generation of direct current(DC)transmission technology,voltage sourced converter(VSC)based high voltage direct current(HVDC)has been widely developed and applied all over the world.China has also carried out a deep technical research and engineering application in this area,and at present,it has been stepped into a fast growing period.This paper gives a general review over China’s VSC based HVDC in terms of engineering technology,application and future development.It comprehensively analyzes the technical difficulties and future development orientation on the aspects of the main configurations of VSC based HVDC system,topological structures of converters,control and protection technologies,flexible DC cables,converter valve tests,etc.It introduces the applicable fields and current status of China’s VSC based HVDC projects,and analyzes the application trends of VSC based HVDC projects both in China and all over the world according to the development characteristics and demands of future power grids.

一种多波长激光器的多模式驱动研究

介绍了一种多波长半导体激光器驱动系统的设计,该系统采用了压控电流源与PicoLAS模块混合驱动的方法,具有效率高、体积小、电路简单可靠、易于系统集成等优点,为半导体激光器的驱动设计提供了一种选择和参考。

一种具有高温保护的三段式充电控制电路

锂电池由于寿命长、容量大、质量轻等优点而应用广泛,但过充和高温都有可能对电池造成极大破坏,因此对锂电池的充电保护设计变得尤为关键。基于Cansemi 0.18μm MIXS 5 V工艺,通过多参量共同作用来调节p沟道金属氧化物半导体(PMOS)管栅极电位,以实现涓流、恒流、恒压三段式充电设计。本设计具有高温调节与保护功能,在高温充电环境下,随着温度的升高,充电电流逐渐减小。直至温度达到门限温度,充电回路彻底关闭,避免了锂电池在高温环境下依然保持大电流充电的情况。仿真以及流片测试结果表明所设计电路能实现三段式充电方式,电池能被充至4.185~4.206 V,精度达到±0.4%以内,且能够实现高温控制与保护功能。

变母线电压的LLC高压电容充电电源设计

提出了一种两级式可变母线电压的高压电容充电电源技术方案,该拓扑在半桥LLC谐振电路的基础上增加了一级图腾柱无桥功率因数校正(PFC)电路,通过改变母线电压来解决传统LLC谐振电源在输出更高电压时,工作频率变化范围过大带来的充电效率下滑的问题。由于图腾柱电路本身具备功率因数校正的功能,该电源设计还拥有能够直接从电网取电而不影响电网电能质量的优势。首先介绍了本电源设计中两部分的电路拓扑和工作原理,采用等效电阻法分析了电容负载下的电源输出特性。针对前级图腾柱电路设计了双环控制器以实现对母线电压和功率因数的控制,针对后级LLC电路提出了比例积分(PI)加低通滤波的恒流控制器以降低高频噪声带来的不利影响。最后通过模型构建与仿真分析,研究了高压电容充电电源3000 V/1 A时的充电特性,验证了本电源技术方案、设计和控制策略的可行性。

高压大容量柔性直流换流阀关键设计和发展趋势

柔性直流输电技术具有控制灵活性高、无换相失败问题和动态无功支撑能力强等突出优点,已广泛应用于点对点输电、背靠背联网和构建直流电网等场景。柔性直流换流阀通过功率器件的频繁开断来实现交、直流的电能转换,是柔性直流输电工程的核心设备。首先,结合工程实践经验,系统梳理并提出了不同应用场景下柔性直流换流阀的关键设计要求,对比分析了柔性直流输电工程中常用的功率器件及柔性直流换流阀拓扑,展望了柔性直流换流阀的发展趋势。此外,针对2种典型的未来应用场景,对比了不同的技术方案,可为柔性直流输电技术应用于高压大容量远距离输电场景提供有益借鉴。

基于双端初始电流行波时频矩阵相似度的柔性直流输电线路保护原理

针对目前柔性直流(voltage source converter-based high voltage DC,VSC-HVDC)电网的线路保护中存在的问题,提出一种基于双端初始电流行波(Initial current traveling wave,ICTW)时频矩阵相似度的柔性直流输电线路保护原理。首先,对柔性直流电网在线路区内外故障下两端保护所在处ICTW的故障特性进行分析,总结出在特定时间窗内,区内故障下两端ICTW的频域相似度远高于区外故障。在此基础上,利用S变换对双端ICTW进行时频分析,建立时频矩阵,并对其做奇异值分解(singular value decomposition,SVD)。然后根据特征矩阵构造双端ICTW的相似度计算公式,以该相似度的大小判别线路区内外故障。另外,根据线路两端ICTW的高低频能量比识别雷击干扰。最后,各种故障情况下的仿真结果表明,该保护原理不依赖线路边界元件,可以保护不同长度线路的全长,具有更高的耐过渡电阻和抗噪声能力,并且能够满足柔性直流电网主保护的速动性要求。