In this paper,the influence of thermal performance of cathode-heater assembly of Traveling Wave Tube(TWT),which has different contact form between inner heat shield and supporting cylinder,is analyzed using the simula...In this paper,the influence of thermal performance of cathode-heater assembly of Traveling Wave Tube(TWT),which has different contact form between inner heat shield and supporting cylinder,is analyzed using the simulation software ANSYS.With both thermal radiation and heat conduction are considered,the temperature and heat flux distribution of structures with different contact form are calculated,and also starting time which is needed before temperature come into steady status.The result of analysis suggests that changing the contact form between inner heat shield and support cylinder can influence the thermal performance of cathode-heater assembly and improve assembly's temperature distribution and promote heater's heating efficiency.The result of this paper provides theoretical guidance in the design of cathode-heater assembly.展开更多
Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic...Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.展开更多
In this paper, we obtain Chen’s inequalities in (k,?μ)-contact space form with a semi-symmetric non-metric connection. Also we obtain the inequalites for Ricci and K-Ricci curvatures.
Based on existing algorithms, a newly developed contact search algorithm is proposed. The new algorithm consists of global search, local searching, local tracking and penetration calculation processes. It requires no ...Based on existing algorithms, a newly developed contact search algorithm is proposed. The new algorithm consists of global search, local searching, local tracking and penetration calculation processes. It requires no iteration steps. It can deal with not only general tool surfaces with vertical walls, but also tool surfaces meshed with elements having very poor aspect ratios. It is demonstrated that the FE code employing this new contact search algorithm becomes more reliable, efficient and accurate for sheet metal forming simulation than conventional ones.展开更多
The mechanically bonded CRA-lined pipe is developed to meet the need forcorrosion-resistant alloy steel pipe. Residual contact pressure at the interface of lined pipe isimportant factor that governs the quality of lin...The mechanically bonded CRA-lined pipe is developed to meet the need forcorrosion-resistant alloy steel pipe. Residual contact pressure at the interface of lined pipe isimportant factor that governs the quality of lined pipe. A simplified theoretical method ispresented to predict the residual contact pressure created by hydraulic pressure. The calculatingequation related hydro-forming pressure to the residual contact pressure between two metal faces isderived. And the validation of the proposed equation is accomplished by comparing its result tothose obtained by experimental investigation.展开更多
The propagation of variations, such as fixture errors and datum errors resulting from assembly and machining processes, has been extensively studied. However, only a few studies that focus on form error propagation in...The propagation of variations, such as fixture errors and datum errors resulting from assembly and machining processes, has been extensively studied. However, only a few studies that focus on form error propagation in assembly systems have been implemented. Machining errors, especially form errors, have great impact on assembly accuracy and accuracy stability of precision mechanical systems. With form errors being the research object, a method for calculating mating variation and specifying mating coordinate is proposed to improve the accuracy of the variation propagation model. Taking into account the form error of mating surfaces, the assembly variation propagation of a precision mechanical system is analyzed, and the brief derivation procedure of the variation propagation model is introduced afterwards. The variation propagation model involves a new concept of mating variation specified by the two mating surfaces. An innovative method, the difference surface search based method, is proposed to calculate the mating variation amongst the mating surfaces. The obtained mating variation is then utilized to specify the mating coordinate in the variation propagation model. Moreover, FEM is employed to simulate the contact state of the two mating surfaces to demonstrate effectiveness of the proposed method. Meanwhile, the mating variation and mating coordinate obtained are incorporated into the assembly variation propagation model, which is then verified by a following case study through a comparison between the calculated results and the experimental results. The comparing results indicate that the established model improves the prediction of assembly accuracy. The developed model enables the investigation of various fundamental issues in variation reduction, including variation analysis, process monitoring, accuracy prediction, and accuracy control.展开更多
The wetting heat and contact angle of sixteen coal samples were determined and the slurry-forming ability of coal were researched. Comparing the relationship of the wetting heat and contact angle with the slurry-formi...The wetting heat and contact angle of sixteen coal samples were determined and the slurry-forming ability of coal were researched. Comparing the relationship of the wetting heat and contact angle with the slurry-forming ability or coal, the auther has found out that the slurry-forming ability of coal can be measured by the wetting heat.展开更多
A meshfree method based on reproducing kernel approximation and point collocation is presented for analysis of metal ring compression. The point collocation method is a true meshfree method without the employment of a...A meshfree method based on reproducing kernel approximation and point collocation is presented for analysis of metal ring compression. The point collocation method is a true meshfree method without the employment of a background mesh. It is shown that, in a point collocation approach, the remesh problem because of the mesh distortion in FEM （finite element method） and the low efficiency in Galerkin-based meshfree method are avoided. The corrected kernel functions are introduced to the stabilization of free-surface boundary conditions. The solution of symmetric ring compression problem is compared with a conventional finite element solution, and reasonable results have been obtained.展开更多
The auto efficiently hydration heat arrangement and the non-contacting electrical resistivity device were used to test the therrnology effect and the resistivity variation of Portland cement hydration. The structure f...The auto efficiently hydration heat arrangement and the non-contacting electrical resistivity device were used to test the therrnology effect and the resistivity variation of Portland cement hydration. The structure forming model of Portland cement initial hydration was established through the systematical experiments with different cements, the amount of mixing water and the chemical admixture. The experimental results show that, the structure forming model of cement could be divided into three stages, i e, solution-solution equilibrium period, structure forming period and structure stabilizing period. Along with the increase of mixing water, the time of inflexion appeared is in advance for thermal process of cement hydration and worsened for the structure forming process. Comparison with the control specimen, adding Na2SO4 makes the minimum critical point lower, the flattening period shorter and the growing slope after stage one steeper. So the hydration and structure forming process of Portland cement could be described more exactly by applying the thermal model and the structure-forming model.展开更多
The contact pressure acting on the sheet/tools interface has been studied because of growing the concern about the wear of tools. Recent studies make use of numerical simulation software to evaluate and correlate this...The contact pressure acting on the sheet/tools interface has been studied because of growing the concern about the wear of tools. Recent studies make use of numerical simulation software to evaluate and correlate this pressure with the friction and wear generated. Since there are many studies that determine the coefficient of friction in sheet metal forming by bending under tension (BUT) test, the contact pressure between the pin and the sheet was measured using a film that has the ability to record the applied pressure. The vertical force applied to pin was also measured. The results indicate that the vertical force is more accurate to set the contact pressure that using equations predetermined. It was also observed that the contact area between the sheet and the pin is always smaller than the area calculated geometrically. The friction coefficient was determined for the BUT test through several equations proposed by various authors in order to check if there is much variation between the results. It was observed that the friction coefficient showed little variation for each equation, and each one can be used. The material used was the commercially pure aluminum, alloy Al1100.展开更多
以水平回转式干馏炉为研究对象,采用离散单元法(discrete element method,DEM)建立颗粒运动模型,接触模型采用Hertz无滑动接触模型,分别对在其内设置不同形式抄板(直角抄板﹑弯抄板和直抄板)的混合效果和混合规律进行了数值研究。将大...以水平回转式干馏炉为研究对象,采用离散单元法(discrete element method,DEM)建立颗粒运动模型,接触模型采用Hertz无滑动接触模型,分别对在其内设置不同形式抄板(直角抄板﹑弯抄板和直抄板)的混合效果和混合规律进行了数值研究。将大小颗粒间接触数与颗粒间接触总数之比定义为混合质量,并以此来衡量混合程度,同时分析抄板形式及转速对混合质量的影响。研究结果表明,干馏炉内设抄板时,混合趋于稳定的时间较短,抄板形式对混合质量的影响较小;随着转速的降低,混合质量曲线越平缓,波动幅度越小。研究结果对干馏炉的设计和优化具有一定的指导作用。展开更多
文摘In this paper,the influence of thermal performance of cathode-heater assembly of Traveling Wave Tube(TWT),which has different contact form between inner heat shield and supporting cylinder,is analyzed using the simulation software ANSYS.With both thermal radiation and heat conduction are considered,the temperature and heat flux distribution of structures with different contact form are calculated,and also starting time which is needed before temperature come into steady status.The result of analysis suggests that changing the contact form between inner heat shield and support cylinder can influence the thermal performance of cathode-heater assembly and improve assembly's temperature distribution and promote heater's heating efficiency.The result of this paper provides theoretical guidance in the design of cathode-heater assembly.
基金This work was supported by the Brain Korea 2lProject and the Grallt of Post-Doc Program, KyungpookNational University (1999).
文摘Some techniques such as die surface description, contact judgement algorithm and remeshing are proposed to improve the robustness of the numerical solution. Based on these techniques, a three-dimensional rigid-plastic FEM code has been developed. Isothermal forging process of a cylindrical housing has been simulated. The simulation results show that the given techniques and the FEM code are reasonable and feasible for three-dimensional bulk forming processes.
文摘In this paper, we obtain Chen’s inequalities in (k,?μ)-contact space form with a semi-symmetric non-metric connection. Also we obtain the inequalites for Ricci and K-Ricci curvatures.
基金the National Natural Science F oundation of China (5 9875 0 2 5 ) and Excellent Young Teacher Founda-tion of the Educational Departm ent of China
文摘Based on existing algorithms, a newly developed contact search algorithm is proposed. The new algorithm consists of global search, local searching, local tracking and penetration calculation processes. It requires no iteration steps. It can deal with not only general tool surfaces with vertical walls, but also tool surfaces meshed with elements having very poor aspect ratios. It is demonstrated that the FE code employing this new contact search algorithm becomes more reliable, efficient and accurate for sheet metal forming simulation than conventional ones.
文摘The mechanically bonded CRA-lined pipe is developed to meet the need forcorrosion-resistant alloy steel pipe. Residual contact pressure at the interface of lined pipe isimportant factor that governs the quality of lined pipe. A simplified theoretical method ispresented to predict the residual contact pressure created by hydraulic pressure. The calculatingequation related hydro-forming pressure to the residual contact pressure between two metal faces isderived. And the validation of the proposed equation is accomplished by comparing its result tothose obtained by experimental investigation.
基金supported by National Natural Science Foundation of China (Grant No. 51075035)National Major Scientific Instruments and Equipments Special Project of China (Grant No. 51127004)National Natural Science Foundation of China (Grant No. 51105036)
文摘The propagation of variations, such as fixture errors and datum errors resulting from assembly and machining processes, has been extensively studied. However, only a few studies that focus on form error propagation in assembly systems have been implemented. Machining errors, especially form errors, have great impact on assembly accuracy and accuracy stability of precision mechanical systems. With form errors being the research object, a method for calculating mating variation and specifying mating coordinate is proposed to improve the accuracy of the variation propagation model. Taking into account the form error of mating surfaces, the assembly variation propagation of a precision mechanical system is analyzed, and the brief derivation procedure of the variation propagation model is introduced afterwards. The variation propagation model involves a new concept of mating variation specified by the two mating surfaces. An innovative method, the difference surface search based method, is proposed to calculate the mating variation amongst the mating surfaces. The obtained mating variation is then utilized to specify the mating coordinate in the variation propagation model. Moreover, FEM is employed to simulate the contact state of the two mating surfaces to demonstrate effectiveness of the proposed method. Meanwhile, the mating variation and mating coordinate obtained are incorporated into the assembly variation propagation model, which is then verified by a following case study through a comparison between the calculated results and the experimental results. The comparing results indicate that the established model improves the prediction of assembly accuracy. The developed model enables the investigation of various fundamental issues in variation reduction, including variation analysis, process monitoring, accuracy prediction, and accuracy control.
文摘The wetting heat and contact angle of sixteen coal samples were determined and the slurry-forming ability of coal were researched. Comparing the relationship of the wetting heat and contact angle with the slurry-forming ability or coal, the auther has found out that the slurry-forming ability of coal can be measured by the wetting heat.
基金the National Natural Science Foundation of China （No. 50275059）.
文摘A meshfree method based on reproducing kernel approximation and point collocation is presented for analysis of metal ring compression. The point collocation method is a true meshfree method without the employment of a background mesh. It is shown that, in a point collocation approach, the remesh problem because of the mesh distortion in FEM （finite element method） and the low efficiency in Galerkin-based meshfree method are avoided. The corrected kernel functions are introduced to the stabilization of free-surface boundary conditions. The solution of symmetric ring compression problem is compared with a conventional finite element solution, and reasonable results have been obtained.
文摘The auto efficiently hydration heat arrangement and the non-contacting electrical resistivity device were used to test the therrnology effect and the resistivity variation of Portland cement hydration. The structure forming model of Portland cement initial hydration was established through the systematical experiments with different cements, the amount of mixing water and the chemical admixture. The experimental results show that, the structure forming model of cement could be divided into three stages, i e, solution-solution equilibrium period, structure forming period and structure stabilizing period. Along with the increase of mixing water, the time of inflexion appeared is in advance for thermal process of cement hydration and worsened for the structure forming process. Comparison with the control specimen, adding Na2SO4 makes the minimum critical point lower, the flattening period shorter and the growing slope after stage one steeper. So the hydration and structure forming process of Portland cement could be described more exactly by applying the thermal model and the structure-forming model.
文摘The contact pressure acting on the sheet/tools interface has been studied because of growing the concern about the wear of tools. Recent studies make use of numerical simulation software to evaluate and correlate this pressure with the friction and wear generated. Since there are many studies that determine the coefficient of friction in sheet metal forming by bending under tension (BUT) test, the contact pressure between the pin and the sheet was measured using a film that has the ability to record the applied pressure. The vertical force applied to pin was also measured. The results indicate that the vertical force is more accurate to set the contact pressure that using equations predetermined. It was also observed that the contact area between the sheet and the pin is always smaller than the area calculated geometrically. The friction coefficient was determined for the BUT test through several equations proposed by various authors in order to check if there is much variation between the results. It was observed that the friction coefficient showed little variation for each equation, and each one can be used. The material used was the commercially pure aluminum, alloy Al1100.
文摘以水平回转式干馏炉为研究对象,采用离散单元法(discrete element method,DEM)建立颗粒运动模型,接触模型采用Hertz无滑动接触模型,分别对在其内设置不同形式抄板(直角抄板﹑弯抄板和直抄板)的混合效果和混合规律进行了数值研究。将大小颗粒间接触数与颗粒间接触总数之比定义为混合质量,并以此来衡量混合程度,同时分析抄板形式及转速对混合质量的影响。研究结果表明,干馏炉内设抄板时,混合趋于稳定的时间较短,抄板形式对混合质量的影响较小;随着转速的降低,混合质量曲线越平缓,波动幅度越小。研究结果对干馏炉的设计和优化具有一定的指导作用。
