Wear and Contact Temperature on Steel Surface in Linear Dry Friction Contact with Polimers with SGF

In this paper, we tried to present a qualitative correlation, based on extensive experimental trials between the value and the evolution of the friction coefficient, wear and contact temperature in the case of linear dry contact, thermoplastic material reinforced with SGF （short glass fibres） and various steel surfaces. We tried, believing successfully, the graphic illustration of the evolution of the steel surface wear and of the contact temperature, depending on the friction coefficient. It was analyzed in detail the influence of the normal load and sliding speed, but also of the metallic surface roughness on the friction coefficient.

Modeling of contact temperatures and their influence on the tribological performance of PEEK and PTFE in a dual-pin-ondisk tribometer

The direct blending of polyether ether ketone(PEEK)with a solid lubricant such as polytetrafluoroethylene(PTFE)improves its tribological performance,but compromises its outstanding mechanical properties and processability.While these negative effects might be circumvented via the hybrid wear method,the influence of the contact temperature between multiple sliding components acting together is not fully understood.Herein,an analytical temperature model considering the influence of both micro-and macro-thermal behavior is extended to predict the contact temperature of a dual-pin-on-disk hybrid wear system.The interactions between several heat sources are investigated and experimentally verified.The analytical results show that the nominal temperature rise of the shared wear track is determined by the combined effect of the heat generated by both pin components,while the rise in flash temperature at the region in contact with each pin component is dependent upon its individual characteristics and working conditions.Hence,while different temperature peaks can coexist in the shared wear track,the maximum value dominates the performance of the system.For the experimentally investigated PEEK–PTFE–steel hybrid wear system,the formation of tribofilms is blocked,and the hybrid wear system fails,when the peak temperature exceeds the glass transition temperature of both pins due to an increase in applied load.

Effect of sintering temperature on the physical properties and electrical contact properties of doped AgSnO_2 contact materials

AgSnO_ 2 electrical contact materials doped with Bi_2O_3,La_2O_3,and TiO_2 were successfully fabricated by the powder metallurgy method under different initial sintering temperatures.The electrical conductivity,density,hardness,and contact resistance of the Ag Sn O_2/Bi_2O_3,AgSnO_2/La_2O_3,and AgSnO_2/Ti O_2 contact materials were measured and analyzed.The arc-eroded surface morphologies of the doped AgSnO_2 contact materials were investigated by scanning electron microscopy(SEM).The effects of the initial sintering temperature on the physical properties and electrical contact properties of the doped AgSnO_2 contact materials were discussed.The results indicate that the physical properties can be improved and the contact resistance of the AgSnO_2 contact materials can be substantially reduced when the materials are sintered under their optimal initial sintering temperatures.

Effect of contact thermal resistance on temperature distributions of concrete-filled steel tubes in fire

To predicate the temperature distribution of concrete-filled steel tubes(CFSTs) being exposure to fire,a finite element analysis model was developed using a finite element package,ANSYS.A suggested value of contact thermal resistance was therefore proposed with the supporting of massive numbers of collected test data.Parametric analysis was conducted subsequently towards the cross-sectional temperature distribution of CFST columns in four-side fire,in which the exposure time,width of the cross section,steel ratio were taken into account with considering contact thermal resistance.It was found that contact thermal resistance has little effect on the overall temperature regulation with the exposure time,the width of cross-section or the change of steel ratio.However,great temperature dropping at the concrete adjacent to the contact interface,and gentle temperature increase at steel tube,exist if considering contact thermal resistance.The results of the study are expected to provide theoretical basis for the fire resistance behavior and design of the CFST columns being exposure to fire.

Diamond Film Synthesis with a DC Plasma Jet:Effect of the Contacting Interface between Substrate and Base on the Substrate Temperature

The contacting interface between the substrate and water-cooled base is vital to the substrate temperature during diamond films deposition by a DC （direct current） plasma jet. The effects of the solid contacting area,conductive materials and fixing between the substrate and the base were investigated without affecting the other parameters. Experimental results indicated that the preferable solid contacting area was more than 60% of total contacting areal; the particular Sn-Pb alloy was more suitable for conducting heat and the concentric fixing ring was a better setting for controlling the substrate temperature. The result was explained in terms of the variable thermal contact resistance at the interface between substrate and base. The diamond films were analyzed by scanning electron microscopy （SEM） for morphology, X-ray diffraction （XRD） for the intensity of characteristic spectroscopy and Raman spectroscopy for structure.

Effect of the annealing temperature on the long-term thermal stability of Pt/Si/Ta/Ti/4H–SiC contacts

The Pt/Si/Ta/Ti multilayer metal contacts on 4H-Si C are annealed in Ar atmosphere at 600°C-1100°C by a rapid thermal processor（RTP）. The long-term thermal stability is evaluated by aging the annealed contact at 600°C in air. The contact＇s properties are determined by current-voltage measurement, and the specific contact resistance is calculated based on the transmission line model（TLM）. Transmission electron microscope（TEM） and energy-dispersive x-ray spectrometry（EDX） are used to characterize the interface morphology, thickness, and composition. The results reveal that a higher annealing temperature is favorable for the formation of an Ohmic contact with a lower specific contact resistance, and causes the rapid degradation of the Ohmic contact in the aging process.

Plasma-assisted surface treatment for low-temperature annealed ohmic contact on AlGaN/GaN heterostructure field-effect transistors

In this study, a low-temperature annealed ohmic contact process was proposed on AlGaN/GaN heterostructure field effect transistors （HFETs） with the assistance of inductively coupled plasma （ICP） surface treatment. The effect of ICP treatment process on the 2DEG channel as well as the formation mechanism of the low annealing temperature ohmic contact was investigated. An appropriate residual AlGaN thickness and a plasma-induced damage are considered to contribute to the low-temperature annealed ohmic contact. By using a single Al layer to replace the conventional Ti/Al stacks, ohmic contact with a contact resistance of 0.35 Ω.mm was obtained when annealed at 575 ℃ for 3 min. Good ohmic contact was also obtained by annealing at 500 ℃ for 20 rain.

Experimental investigation of high temperature thermal contact resistance with interface material

Thermal contact resistance plays a very important role in heat transfer efficiency and thermomechanical coupling response between two materials,and a common method to reduce the thermal contact resistance is to fill a soft interface material between these two materials.A testing system of high temperature thermal contact resistance based on INSTRON 8874 is established in the present paper,which can achieve 600 C at the interface.Based on this system,the thermal contact resistance between superalloy GH600 material and three-dimensional braid C/C composite material is experimentally investigated,under different interface pressures,interface roughnesses and temperatures,respectively.At the same time,the mechanism of reducing the thermal contact resistance with carbon fiber sheet as interface material is experimentally investigated.Results show that the present testing system is feasible in the experimental research of high temperature thermal contact resistance.

Morphology and electrical contact properties of electrical connection materials in corrosive atmosphere

The impact mechanism of environmental fac tors, such as corrosive atmosphere, on connector materials was investigated, and the porosity of gold plating was tested. Series of inspections and analytical research meth ods were introduced in this article. The surface morphology of specimens after corrosion was observed by stereoscopic microscope and scanning electron microscope. Chemical constitution was examined by Xray energy spectrum. The contact resistances were measured by fourpoint method. The experiment results show that after exposure to certain environment, the corrosion products, such as Cu20, Cu（NO3）2.3H20, and NiO, are observed on the surface of the specimens without gold coatings, whereas the corrosion products appear to have circleshaped spots on goldplating surface after corrosion test, which indicate that the gold plating has good corrosion protection. The porosity is increased with the increase of corrosion time for every kind of specimens gold plated, and the corrosion degree of gold plating specimens is decreased with the increase of the thickness of gold coatings. The static contact resistances of circleshaped spots appear higher contact resistance than normal value, which can reach to 2,000 mr2 nearly. It is found that the high and unstable contact resistance of the pore and products is more likely to cause contact failure.

Evolution of the electrical contact of dynamic pantograph–catenary system

A good contact between the pantograph and catenary is critically important for the working reliability of electric trains, while the basic understanding on the electrical contact evolution during the pantograph--catenary system working is still ambiguous so far. In this paper, the evolution of electric contact was studied in respects of the contact resistance, temperature rise, and microstructure variation, based on a home-made pantograph-catenary simulation system. Pure carbon strips and copper alloy contact wires were used, and the experimental electrical current, sliding speed, and normal force were set as 80 A, 30 km/h, and 80 N, respectively. The contact resistance presented a fluctuation without obvious regularity, concentrating in the region of 25 and 50 mf~. Temperature rise of the contact point experienced a fast increase at the first several minutes and finally reached a steady state. The surface damage of carbon trips in microstructure analysis revealed a complicated interaction of the sliding friction, joule heating, and arc erosion.

An Experimental Study on the Drag Property of High-Temperature Particles Falling into Cold Liquid Pool

This experiment is to study the special resistant induced by the high-speed evaporation surrounding themoving high-temperature particles. An observable equipment was designed, in which the first 11 experiments wereperformed by pouring one or several Zirconia spheres with various high-temperature and a diameter of 3～ 10 mminto a water pool. The particles falling-down speeds were recorded by high-speed photographic instrumentation,and pressures and water temperatures were measured. A comparison between the experiments with cold and hotspheres respectively, employing three different sphere types each, was presented. The experimental data, com-pared with the theory of the evaporation drag model, are nearly identical.

Experiment and finite element method analysis mass erosion and transfer of Ag/La_2NiO_4-based electrical contacts during operation

A uniform transient temperature field model of electrical contacts operation was found by analyzing the process of closing arc constriction resistance Joule heat ~ breaking arc. Essential parameters of Ag/La2NiO4 electrical contact material for transient temperature field calculation were obtained through tests of electrical contact experimental instrument under 18 V DC in different cur- rents, other correlation experiments, and calculation anal- ysis. The finite element method was applied to solve the transient temperature field, and the features and distribution of the transient temperature field were obtained. The condition of material erosion and mass transfer can be forecasted by those calculation results. It is beneficial to research about the lifetime of Ag/La2NiO4 electrical material.

Temperature field analysis of two rotating and squeezing steel-rubber rollers

Rubber has strong nonlinear viscoelastic characteristic. Under effect of the periodically changing external force,it will show the phenomenon of lagging deformation and mechanical loss,which means deformation lags behind stress changes and the situation of loss of work is caused by the hysteresis. Loss of work will be transformed into thermal energy and makes the temperature of rubber and the object in contact with it rise,which will thereby affect the dynamic characteristics of the structure. Based on a pair of mutual rotating and squeezing steel-rubber rollers as the research object,the finite element simulation software Ansys is used in this paper to analyze the temperature field of the structure. As a result,temperature distribution characteristics of two directions are obtained. One is squeezing area along the direction of the wall,the other is along the direction of thickness of rubber. Then the influence of the rotating speed and the pressure between two rollers on temperature of rubber is analyzed. The temperature experiment of mutual squeezing contact steelrubber roller is carried out on the experimental platform via using infrared thermal imager and infrared thermometer. The experiment data are in accordance with the simulation results on regulation of temperature distribution as well as high degree of similarity on value,which shows the effectiveness of simulation. Research results are of great significance for temperature characteristic analysis of rubber structure.

Research on Non-Contact Weak Current Detection Technology

With the continuous development of industrial technology, the weak current plays an increasingly important role in all fields of life. In order to facilitate the user to carry, the study of contactless weak current measurement technology is also emerging. This article’s design idea is based on two-dimensional reluctance sensor device built non-contact weak current detection system. The system uses the reluctance sensor HMC1002 to collect the current signal and the temperature sensor DS18B20 to compensate the temperature. The signals collected by the reluctance sensor and the temperature sensor are extremely weak. After being amplified by the amplifying circuit, the signal is conducive to subsequent detection and processing. Filter circuit can filter out interference signals to achieve the goal of improving accuracy. After the corresponding algorithm of the microcontroller will convert the signal voltage, easy to read and store, thus designing a non-contact current measurement capable of detecting weak currents and achieving higher accuracy.

Surface XPS-investigations of tobacco leaves treated with low-temperature plasma

The tobacco leaves were treated with low-temperature plasma in Ar, N2, O2, and air atmospheres at different powers (60―130 W). The surface-elemental components, their relative contents, and the functional groups of the surface components of the tobacco leaves were determined using XPS (X-ray photoelectron spectroscopy). The ex- perimental results showed that the percentage of the elements C, N, and O had changed considerably and a large number of polar functional groups containing oxygen atoms were incorporated into the components on the tobacco surfaces. The measurements of the surface contact angle showed that the surface contact angle of the modified tobacco leaves was 0 degree, whereas it was 110 degrees before the plasma treatment. These results indicate that the wettability of the modified tobacco leaves improved dramatically. This work may be significant for future researches on the surface modification of the tobacco leaves.

盘式制动器在不同制动模式下的热-机耦合行为研究

对盘式制动器在拖曳制动、紧急制动和缓慢制动这3种不同制动模式下的热-机耦合行为进行分析。结果表明,在拖曳制动模式下,制动盘两侧摩擦片的变形形式各不相同,因此制动盘两侧摩擦片的温度分布不一致。此外,钳指侧和活塞侧摩擦片的振动信号和接触力信号差异明显,钳指侧对摩擦副的摩擦振动逐渐加剧,并产生新的振动频率;活塞侧对摩擦副的振动趋于稳定,原有的振动频率逐渐消失;在紧急制动模式下,制动盘两侧摩擦片的温度分布特征类似,均是从进摩擦区向出摩擦区扩散,但是由于作用时间较短,温度上升不明显。但两侧摩擦片的振动信号有所区别,尤其是活塞侧摩擦片出现持续自激振动,并且产生新的振动频率。在缓慢制动模式下,虽然制动盘两侧的摩擦片外径均为表面高温区,但在制动后期,活塞侧摩擦片表面高温排布呈现出“点状分布式”特点。钳指侧摩擦片和活塞侧摩擦片的振动信号存在差异,钳指侧摩擦片振动持续时间较长,但其振动强度较活塞侧则更加微弱。界面力学信号分析结果很好地验证了该结论。

Influence of RE on Ageing Precipitate Characteristics and Softening Resistance of Copper Alloys Contact Wire

The effect of RE （such as Ce, Y and mixed Ce ＋ Y, etc） on ageing precipitate, characteristics and softening resistance of Cu-Cr-Zr alloys contact wire used in electrical railway were investigated in this paper. The results show that the tested Cu-Cr-Zr alloy with trace RE addition could attain higher microhardness and lower electrical conductivity to some extent after being soluted at 950 ℃ for 1 h and aged at 480 ℃. The precipitation process of secondary phase could be accelerated by cold working before ageing treatment which resulted in ageing hardening. Aged at 480 ℃ after 60% cold working, the values of electrical conductivity and microhardness improved significantly compared with that without deformation. The mixed RE （Ce ＋ Y） improved the softening resistance substantially in these trace RE additions, which could increase the soften temperature by 45 ℃.

Realization of laser textured brass surface via temperature tuning for surface wettability transition

Superhydrophobic surfaces have attracted extensive interests and researches into their fundamentals and potential applications.Laser texturing provides the convenience to fabricate the hierarchical micro/nanostructures for superhydrophobicity.However,after laser texturing,long wettability transition time from superhydrophilicity to superhydrophobicity is a barrier to mass production and practical industrial applications.External stimuli have been applied to change the surface composition and/or the surface morphology to reduce wettability transition time.Herein,by temperature tuning,wettability transition of laser textured brass surfaces is investigated.Scanning electron microscopy and surface contact angle measurement are employed to characterize the surface morphology and wettability behavior of the textured brass surfaces.By low-temperature heating(100℃~150℃),partial deoxidation of the top Cu O layer occurs to form hydrophobic Cu_2O.Therefore,superhydrophobicity without any chemical coating and surface modification could be achieved in a short time.Furthermore,after low-temperature heating,the low adhesive force between the water droplet and the sample surface is demonstrated for the laser textured brass surface.This study provides a simple method to fabricate the micro/nanostructure surfaces with controllable wettability for the potential applications.