Mechanical properties and acoustic emission characteristics of soft rock with different water contents under dynamic disturbance

Uniaxial compression tests and cyclic loading acoustic emission tests were conducted on 20%,40%,60%,80%,dry and saturated muddy sandstone by using a creep impact loading system to investigate the mechanical properties and acoustic emission characteristics of soft rocks with different water contents under dynamic disturbance.The mechanical properties and acoustic emission characteristics of muddy sandstones at different water contents were analysed.Results of experimental studies show that water is a key factor in the mechanical properties of rocks,softening them,increasing their porosity,reducing their brittleness and increasing their plasticity.Under uniaxial compression,the macroscopic damage characteristics of the muddy sandstone change from mono-bevel shear damage and‘X’type conjugate bevel shear damage to a roadway bottom-drum type damage as the water content increases.Dynamic perturbation has a strengthening effect on the mechanical properties of samples with 60%and less water content,and a weakening effect on samples with 80%and more water content,but the weakening effect is not obvious.Macroscopic damage characteristics of dry samples remain unchanged,water samples from shear damage and tensile–shear composite damage gradually transformed into cleavage damage,until saturation transformation monoclinic shear damage.The evolution of acoustic emission energy and event number is mainly divided into four stages:loading stage(Ⅰ),dynamic loading stage(Ⅱ),yield failure stage(Ⅲ),and post-peak stage(Ⅳ),the acoustic emission characteristics of the stages were different for different water contents.The characteristic value of acoustic emission key point frequency gradually decreases,and the damage degree of the specimen increases,corresponding to low water content—high main frequency—low damage and high water content—low main frequency—high damage.

The effect of Ti and Zr content on the structure,mechanics and energy-release characteristics of Ti—Zr—Ta alloys

Energetic structural materials(ESMs)are a new type of structural materials with bearing and damage characteristics.In this work the microstructure,mechanical properties and energy release characteristics of multi-element Ti-Zr-Ta alloys with good casting performance were studied.The microstructure of the Ti_(x)ZrTa alloys gradually change from BCC+HCP to single BCC structure with the increase of Ti.While the Ti_(2)Zr_(y)Ta alloys was still uniform and single BCC structure with the increase of Zr.The evolution of microstructure and composition then greatly affect the mechanical properties and energy-release characteristics of Ti-Zr-Ta alloys.The synergistic effect of dual phase structure increases the fracture strain of Ti_(x)ZrTa(x=0.2,0.5)with the Ti content decreases,while the fracture strain of Ti_(x)ZrTa(x=2.0,3.0,4.0)gradually increase with the Ti content increases caused by the annihilation of the obstacles for dislocation movement.And as Zr content increases,the fracture strain of Ti_(2)Zr_(y)Ta alloys decrease,then the oxidation reaction rate and fragmentation degree gradually increase.The higher oxidation rate and the lager exposed oxidation area jointly leads the higher releasing energy efficiency of Ti_(x)ZrTa alloys with low Ti content and Ti_(2)Zr_(y)Ta alloys with high Zr content.

Energy release characteristics of PTFE/Al/TiH_(2) reactive jet with different TiH_2 content

Titanium hydride(TiH_(2)), a promising high-energy additive, is doped into PTFE/Al to optimize the energy output structure of the reactive jet and strive for better aftereffect damage ability to the target. Six types of PTFE/Al/TiH_(2) reactive liners with different TiH_(2) content are prepared by the molding and sintering method. The energy release characteristics of PTFE/Al/TiH_(2) reactive jet are tested by the transient explosion energy test, and are characterized from pressure and temperature. The reaction delay time,pressure history, and temperature history of the energy release process are obtained, then the actual value of released energy and reaction efficiency of the reactive jet are calculated. The results show that the peak pressure and temperature of the PTFE/Al/TiH_(2) jet initially increase and then decrease with increasing TiH_(2) content. When the TiH_(2) content is 10%, the actual value of released energy and reaction efficiency increased by 24% and 6.4%, respectively, compared to the PTFE/Al jet. The reaction duration of the reactive material is significantly prolonged as the TiH_(2) content increased from 0% to 30%. Finally,combined with the energy release behaviors of PAT material and the dynamic deformation process of liner, the enhancement mechanism of TiH_(2) on energy release of the reactive jet is expounded.

Study on the Relationship between.the Moisture Content of Brown Rice and Milling Characteristics

An experiment about rice milling was made to study on the relationship between the different moisture content of brown rice and the energy consumption, the broken rice rate, the crack rate and the head rice yield. It could be concluded that the head rice yield increased at first falls and then along with the raise of moisture content and it could reach the maximum 70.78% when moisture content was 15.5%; the energy consumption of rice milling decreased along with the increase of moisture contents; the broken rice rate fell at first and then increased along with the raise of moisture contents and it could reach the minimum 4.28% when the moisture content was 15.5%.

Influence of sand content on the flow characteristics of soft soil under cyclic and high-frequency vibration

The flow characteristics of foundation soils subjected to train loads can present engineering hazards in highspeed railways.In order to verify the feasibility of blending coarse sand in modifying soft subsoil,undrained pulling sphere tests were carried out and the train loads were simulated through localized and cyclic vibration at various frequencies.Laboratory testing results indicate that the fl ow characteristics of soft soil can be signifi cantly enhanced by high-frequency vibration;meanwhile the continuous increase in fl ow characteristics caused by cyclic vibration may be an important reason for the long-term settlement of soft subsoil.The infl uence of sand content on fl ow characteristics is also studied in detail,and it is shown that the addition of coarse sand can weaken the fl ow characteristics of soft soil induced by sudden vibration at lower than 50 Hz.Under the condition of cyclic vibration,the growth of the fl ow characteristics of sand-clay mixtures is mainly caused by the fi rst-time vibration in the cycle,and the increase in sand content can make the fl ow characteristics present a faster convergent tendency.

Effects of copper content on the shell characteristics of hollow steel spheres manufactured using an advanced powder metallurgy technique

Metallic hollow spheres are used as base materials in the manufacture of hollow sphere structures and metallic foams. In this study, steel hollow spheres were successfully manufactured using an advanced powder metallurgy technique. The spheres＇ shells were characterized by optical microscopy in conjunction with microstructural image analysis software, scanning electron microscopy（SEM）, energy-dispersive X-ray spectroscopy（EDX）, and X-ray diffraction（XRD）. The microscopic evaluations revealed that the shells consist of sintered iron powder, sintered copper powder, sodium silicate, and porosity regions. In addition, the effects of copper content on various parameters such as shell defects, microcracks, thickness, and porosities were investigated. The results indicated that increasing the copper content results in decreases in the surface fraction of shell porosities and the number of microcracks and an increase in shell thickness.

Statistical characteristics of heavy metals content in groundwater and their interrelationships in a certain antimony mine area

In recent years, most of domestic and foreign researches about heavy metal pollutions of metal mine mainly focus on water, soil and plants on the surface. There is lack of researches about heavy metal pollution in groundwater of metal mine. In this research, a certain antimony mine area is selected as a typical study area. Also, the study about statistical characteristics of heavy metals in groundwater has been carried out. Furthermore, the interrelationships have been preliminarily discussed through related analysis, such as relevant analysis, cluster analysis and principle component analysis. The results show that: the excessive elements in groundwater of study area are Sb, As, Pb, Se, and Ni. The average mass concentration of Sb, As, and Pb is higher than that of drinking water standards(GB5749-2006). The concentration of most heavy metals in dry season is lower than or equal to that in wet season for groundwater. Zn is the only metal in groundwater showing a different pattern, the concentration of which in dry season is higher than that in wet season. Under the impacts of stratum leaching and absorption effect, the concentration of heavy metals(except Pb and Ba) in groundwater are lower than or equal to that in surface water. As and Se, the two heavy metals have a significant positive correlation, which shows the two elements might have gone through similar environmental geochemical effect. Also, the connection among Zn, Hg, Pb, and Mn is not obvious; therefore, the sources of those elements are quite different. In addition, the elements of Se and As have obvious positive interrelationship with elements of CO_3^(2-) and F^-. Also, the Pb has significant positive correlation with PO_4^(3-), H_2SiO_3 and oxygen consumption. The results of cluster analysis show that 9 different heavy metals in the study area can be divided into 3 categories: Zn, Cd, Mn, Hg, Cu, and Cr belong to the first category, Se and As belong to the second one, and the last category is Pb. Also, the principle component analysis divides 6 heavy metals(Zn, As, Hg, Pb, Mn, and Se) into 4 different principle components, which can be utilized to assess heavy metals pollution situations in groundwater. The reliability of this method is higher than 91%. Moreover, the research provides theory basis and models for establishing evaluation index system and exploring the evaluation method of heavy mental pollution in groundwater.

Effect of oxygen content on dielectric characteristics of Cr-doped LaTiO_(x)

The ceramics La_(0.85)Cr_(0.15)TiO_(x)and La_(0.7)Cr_(0.3)TiO_(x)are prepared by conventional solid-state reaction method.The dielectric properties of Cr-doped La TiO_(x)as a function of frequency(0.1 k Hz≤f≤1 MHz)and temperature(77 K≤T≤360 K)are studied.The blocks are then annealed in a flowing O2 or Ar/H_(2)to convert their oxygen content and the tests mentioned above are performed.The highly oxygenated samples exhibit extremely high low-frequency dielectric constants at room temperature(~10^(6)).The results show that the oxygen stoichiometry could significantly influence the dielectric properties of Cr-doped LaTiO_(x).

Influence of soil organic matter contents on soil water characteristics of forests on east slope of Gongga Mountain

By testing soil organic matter （SOM） contents, soil water contents （SWC） within low suctions, and saturated infiltration rates of samples taken from east slope of Gongga Mountain of China, the enhancive effects of SOM contents on SWC within low suctions and saturated infiltration rates were quantified. The simulated functions might be applied on regional experience forest-hydrology model. The improving function of protecting forest floor and increasing SOM contents on forest ecosystem hydrological effects were also embodied.

Study on Soil Nutrient Contents and Nutrient Characteristics of Ginger(Zingiber officinale Rosc.)

[Objective] This study was conducted to provide scientific basis for fertilization of ginger with high quality and high yield. [Method] The soil nutrient contents and plant nutrient characteristics of Zhugen ginger（Zingiber officinale Rosc.） were studied. [Result] The results showed that： the soil of ginger planting area in Chongqing（Yongchuan） Seedlings of science and technology city was acidic overall,the soil organic matter content was low and alkali-hydrolyzable N was at moderate level; and the contents of available P, Ca, Mg, Fe, Mn, Cu and Zn were extremely rich, while the available S was in lack. The contents of N and K were abundant and P was little in ginger plants, the content of K was more than N in ginger roots and stems, while the content of N was more than K in ginger leaves. [Conclusion]In practical production, it was necessary to fertilize rationally and control the ratio of N fertilizer to K fertilizer according to local conditions, thereby promoting ginger growth and realize high-yield ginger production.

Effects of Formulated Fertilizer Synergist on Abscisic Acid Accumulation, Proline Content and Photosynthetic Characteristics of Rice under Drought

To investigate the effects of formulated fertilizer synergist on the drought tolerance in rice, pot experiment was conducted to analyze the photosynthetic characteristics and the accumulation of abscisic acid （ABA） and proline in middle-season rice variety Peiliangyou 93. The synergist could improve the net photosynthetic rate, and coordination between the water loss and the CO2 absorption as well as reduce the harmful effect on photosynthetic process under drought conditions. Under drought, the ABA accumulated massively both in roots and leaves, while the ABA content in roots was far higher than that in leaves. The results indicate that synergist could increase the ABA accumulation, but reduce the proline accumulation in rice plant under drought.

Diversity of Antioxidant Content and Its Relationship to Grain Color and Morphological Characteristics in Winter Wheat Grains

The current interest in the health beneifts of whole wheat grain has prompted breeders to further increase the concentration of antioxidants in wheat. The objective of this study was to investigate the variation in antioxidant content among Chinese wheat grains and the relationship between antioxidants and grain color and morphological characteristics. A wide variation was observed in the total phenolic, carotenoid and lfavonoid contents, as well as the antioxidant activity （AOA）, of Chinese wheat varieties. Black wheat had the highest mean total phenolic, carotenoid and lfavonoid contents and the highest AOA, followed by red and white wheats. The grain color parameters were signiifcantly negatively correlated with total phenolic, carotenoid and lfavonoid contents and AOA among all of the wheat varieties examined, and grain weight was also signiifcantly negatively correlated with these traits. The same correlation between grain weight and antioxidant traits was also observed within individual groups of wheat, which indicates that grain weight may be used as an index for selecting wheat varieties with high AOA. Landraces had signiifcantly higher lfavonoid content than commercial wheat varieties. The results of this study may be useful for breeding nutrient-rich wheat varieties.

The Relationship Between Plant Community Characteristics and Soil Organic Matter Content of Sedentary Grazing Pastures in a Typical Steppe

In order to discuss the relationship between the characteristics of plant communities and the content of topsoil organic matter under the condition of two-season sedentary grazing, authors of this paper selected a Stipa krylovii steppe for research and studied the plant community characteristics and the topsoil organic matter content. The results showed that in the sedentary grazing area, the perennial plant species decreased, the annual plant species increased, and the topsoil organic matter content decreased. There were a negative correlation between plant biomass and topsoil organic matter content, and a positive correlation between total coverage and topsoil organic matter content. The change of plant community characteristics in the sedentary grazing area was related to the implementation of the system of transferring the pasture use rights to the herdsmen and controlled grazing.

Effects of RNAi Silencing of SSIII Gene on Phosphorus Content and Characteristics of Starch in Potato Tubers

The sense and antisense fragments of the soluble starch synthase （SSII1） gene and the intron fragment of somatic embryogenesis receptor-like kinase （SERK1） gene were cloned from potato using PCR techniques. The RNAi plant expression vectors pBI-SSIII-RNAi and pBIC-SSIII-RNAi were constructed which containing fusion fragment of ＂sense fragment-intron-antisense fragment＂ driven by the constitutive expression promoter CaMV 35S and the tuber-specific expression promoter CIPP, respectively. The putative transgenic plants of potato cultivars Kexin-1 and Kexin-4 were obtained using Agrobacterium-mediated transformation method. PCR assay showed that the interference fragment of SSlll gene was integrated into potato genome. The RT-PCR analysis showed that the expression of SSlll gene was repressed apparently on the transcription level. Starch granules of the transgenic potato plants were different in morphology and became cracked in starch granule centre compared with the non-transgenic control plants. The amylose content of starch was increased by 2.68-29.05%, amylopectin to amylose ratio of starch had declined significantly, and the phosphorus content of the starch of the transgenic plants was reduced 9.94-58.36% compared with control plants. The results could provide certain foundation for improvement of potato starch quality.

Effect of steam pretreatment on wood moisture content and characteristics of vacuum drying

The effects of high temperature steam pretreatment on the change in wood moisture content （MC） and characteristics of vacuum drying were investigated in this study. Poplar and manchurian walnut woods were pretreated with high temperature steam at 100~C and 140~C, prior to vacuum drying. A comparison of the characteristics of vacuum drying between steam pretreated wood and untreated wood was carried out. The results show that during steam pretreatment, the MC of wood decreased within a few hours. The reduction of MC varied with the temperature; the higher the temperature, the faster the MC dropped. During the vacuum drying stage, the rates of drying ofpretreated samples were higher than those of untreated samples when MC was below the fiber saturation point. Furthermore, the total drying time of samples treated at a steam temperature of 140~C was lower than that of untreated samples. Therefore, a vacuum procedure after steam pretreatment can effectively shorten the drying time when drying wood.

Effects of CBN content on characteristics of PCBN composites in turning GCr15 hardened steels

Well-sintered polycrystalline cubic boron nitride(PCBN)composites with different contents of cubic boron nitride(CBN) were obtained using Al and TiN as additives under pressure of 5.5 GPa and temperature of 1450 ℃.The network structure of CBN grains and bonding materials was observed using scanning electron microscope(SEM).With the help of X-ray diffraction(XRD) analysis,TiB2 and AlN could be determined as main products and Al3 Ti also was detected in the Al-rich samples after sintering process.Furthermore,it was shown that Vickers hardness of composites was improved with the increase of CBN contents.However,the lifetime of PCBN composites was in negative correlation with the amount of CBN in turning GCr15 hardened steels,and the surface roughness of workpieces machined by these PCBN composites also showed the same trend.A series of cutting data confirmed that the low CBN content in PCBN composites could enhance the working durability and improve the surface quality in turning hardened steels.The present experiments also indicated that the lowest value of flank wear was not constant for different PCBN composites when they were used to machine several workpieces with different hardness.

Physicochemical Characteristics and QTL Mapping Associated with the Lipid Content of High-Lipid Rice

This study was conducted to examine the physicochemical characteristics and perform QTL mapping of genetic factors associated with the lipid content of rice. A rice strain with a high lipid content, “P31-2-2-2-B-B”, was developed from mutants of “Dongjin” created by T-DNA insertion. The lipid content of “P31-2-2-2-B-B” brown rice was 4.42% whereas that of the donor cultivar “Dongjin” was 2.56%. The total fatty acid content of the high-lipid mutant brown rice was 7.82% and that of “Dongjin” was 3.43%. The unsaturated fatty acid composition of the mutant brown rice was 2.73% oleic acid, 2.74% linoleic acid, and 0.34% linolenic acid. In contrast, the fatty acid composition of the donor cultivar “Dongjin” was 1.30% oleic acid and 0.99% linoleic acid. The percentage of unsaturated fatty acid to total fatty acid in the high-lipid mutant was higher (74.3%) than that of “Dongjin” (66.8%). Continuous frequency distribution and transgressive segregation of the lipid content were observed in the F3 family (seeds) derived from a cross between the high-lipid mutant “P31-2-2-2-B-B” and a tongil-type cultivar “Samgang”. This result implied that the lipid content was a quantitative trait controlled by a polygene. Additionally, the broad sense heritability of lipid content was estimated to be 89.6% based on analysis of the F3 seeds. A significant QTL, qRLC5, was identified on chromosome 5 with a LOD score of 2.37, and was flanked by 5007 and 5014. Results of the present study should be useful for improving rice nutritional quality through marker-assisted selection.

Effects of Fermented Nori (<i>Pyropia yezoensis</i>) Liquid Fertilizer on Plant Growth Characteristics and Nutrient Content of Komatsuna (<i>Brassica rapa</i>L. var. Wakana Komatsuna) Cultivated in Vermiculite

We conducted plant growth experiments in microbe-free vermiculite to study the effects of four types of fermented seaweed liquid fertilizer (SLF) made from nori (Pyropia yezoensis) seaweed on the germination, plant growth characteristics, SPAD value, and nutrient content and uptake of komatsuna (Brassica rapa L. var. wakana komatsuna). The four types of fermented nori SLF used in this study were prepared by anaerobic fermentation of unwashed nori (SLF1), aerobic fermentation of unwashed nori (SLF2), anaerobic fermentation of washed nori (SLF3), and aerobic fermentation of washed nori (SLF4). Komatsuna seeds treated with 200-, 300-, and 400-fold dilutions of SLFs exhibited improved relative germination ratios (RGRs) at 3 and 4 days after sowing (DAS). At 4 DAS, the RGRs of seeds treated with 10-, 100-, 200-, 300-, and 400-fold SLF dilutions showed no differential effect. Seeds treated with undiluted SLFs did not germinate by 4 DAS. SLF1 may promote komatsuna seed germination. The nitrogen (N), calcium, magnesium, sodium (Na), and iodine (I) contents of plants treated with SLF1 were significantly increased relative to plants treated with the other SLFs. Moreover, the I and Na contents of plants were significantly increased by foliar spray application of different dilutions of SLF1. However, SLF treatment markedly reduced the shoot dry weight compared with 1/2-strength modified Hoagland nutrient (MHN) solution, although the same amounts of N and K were applied. SPAD values of the plants treated with SLFs were significantly higher than those of plants treated with MHN. Foliar treatment with SLFs had no significant effect on plant growth, SPAD value, or uptake of nutrients (except Na) relative to the control, but the I content was increased. Plants treated with SLF1 and SLF2 exhibited the highest Na uptake. Foliar spray treatments with SLF1 resulted in the highest I contents in plants. Based on our results, SLF1 is suitable for use as a liquid fertilizer to promote germination and increase nutrient content in komatsuna. These results need to be followed up in soil experiments in the presence of microbes in the rhizosphere.

Content Characteristics of Knowledge Integration in the eHealth Field:An Analysis Based on Citation Contexts

Purpose:This study attempts to disclose the characteristics of knowledge integration in an interdisciplinary field by looking into the content aspect of knowledge.Design/methodology/approach:The eHealth field was chosen in the case study.Associated knowledge phrases(AKPs)that are shared between citing papers and their references were extracted from the citation contexts of the eHealth papers by applying a stem-matching method.A classification schema that considers the functions of knowledge in the domain was proposed to categorize the identified AKPs.The source disciplines of each knowledge type were analyzed.Quantitative indicators and a co-occurrence analysis were applied to disclose the integration patterns of different knowledge types.Findings:The annotated AKPs evidence the major disciplines supplying each type of knowledge.Different knowledge types have remarkably different integration patterns in terms of knowledge amount,the breadth of source disciplines,and the integration time lag.We also find several frequent co-occurrence patterns of different knowledge types.Research limitations:The collected articles of the field are limited to the two leading open access journals.The stem-matching method to extract AKPs could not identify those phrases with the same meaning but expressed in words with different stems.The type of Research Subject dominates the recognized AKPs,which calls on an improvement of the classification schema for better knowledge integration analysis on knowledge units.Practical implications:The methodology proposed in this paper sheds new light on knowledge integration characteristics of an interdisciplinary field from the content perspective.The findings have practical implications on the future development of research strategies in eHealth and the policies about interdisciplinary research.Originality/value:This study proposed a new methodology to explore the content characteristics of knowledge integration in an interdisciplinary field.

Identifying the influence of urbanization on soil organic matter content and p H from soil magnetic characteristics

Soil magnetic characteristics are correlated with soil p H and organic matter content. Analyzing soil magnetic characteristics, organic matter content and p H can indirectly evaluate soil pollution caused by human activities. This study analyzed the soil magnetic characteristics, organic matter content and p H in surface soil samples from different land use types in Shihezi city, a newly and rapidly developing oasis city in Xinjiang of China. The aims of this study were to explore the possible relationships among the soil magnetic parameters and thereby improve the understanding of influence of urbanization on soil properties. Eighty surface soil samples at the depth of 0–10 cm were collected from 29 July to 4 August 2013. The results showed that the magnetic minerals in surface soil were dominated by ferromagnetic minerals. Spatially, the magnetic susceptibility（χLF）, anhysteretic remanent magnetization susceptibility（χARM）, saturation isothermal remanent magnetization（SIRM） and ＂soft＂ isothermal remanent magnetization（SOFT） were found to be most dominant in the new northern urban area B（N-B）, followed by built-up areas（U）, suburban agricultural land（F）, and then the new northern urban area A（N-A）. The values of χLF, χARM, SIRM and SOFT were higher in the areas with high intensities of human activities and around the main roads. Meanwhile, the property ＂hard＂ isothermal remanent magnetization（HIRM） followed the order of U〉N-B〉F〉N-A. Built-up areas had an average p H value of 7.93, which was much higher than that in the new northern urban areas as well as in suburban agricultural land, due to the increased urban pollutant emissions. The average value of soil organic matter content in the whole study area was 34.69 g/kg, and the values in the new northern urban areas were much higher than those in the suburban agricultural land and built-up areas. For suburban agricultural land, soil organic matter content was significantly negatively correlated with χLF, and had no correlation with other magnetic parameters, since the soil was frequently ploughed. In the new northern urban areas（N-A and N-B）, there were significant positive correlations of soil organic matter contents with χARM, SIRM, SOFT and HIRM, because natural grasslands were not frequently turned over. For the built-up areas, soil organic matter contents were significantly positively correlated with χLF, χARM, SIRM and SOFT, but not significantly correlated with frequency-dependent susceptibility（χFD, expressed as a percentage） and HIRM, because the soil was not frequently turned over or influenced by human activities. The results showed that soil magnetic characteristics are related to the soil turnover time.