In order to study the influence of die combination on continuous variable cross-section direct extrusion （CVCDE） in the extrusion process, the accumulative strain formula is derived, and it can be known that the ext...In order to study the influence of die combination on continuous variable cross-section direct extrusion （CVCDE） in the extrusion process, the accumulative strain formula is derived, and it can be known that the extrusion ratio of various stages directly determines the size of corresponding stage strain by formula. In this paper, as an example of the two interim dies, three die combinations of different angles and extrusion ratio are designed. Aviation magnesium alloy ZM6 is studied, and the results show that dynamic recrystallization is even more complete when continuous shear deformation occurs, so that the refinement and homogenization of microstructure are obtained. By the use of different die combinations, the accumulative strain increases under the conditions of same total extrusion ratio. Thus, the refined crystalline strengthening effect of extrusion deformation can be further analyzed. Due to the dead-zone defects, the actual accumulative strain decreases significantly and the effect of microstructure and performance improvements also decreases with it. Therefore, the optimal design of die combination is the key to the process and product of CVCDE, which provides a scientific basis for the development of severe plastic deformation.展开更多
Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and sc...Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and scanning electron microscopy（SEM） were used to observe the variations in microstructure and fracture morphology of Mg alloy AZ31 as a function of processing methods. The results reveal that grains of Mg alloy AZ31 were refined and their microstructure was homogenized by CVCDE. The recrystallization in Mg alloy AZ31 produced by CVCDE with 2 interim dies was more complete than that produced by conventional extrusion（CE） and CVCDE with 1 interim die, and the grains were finer and more uniform.Plasticity of the AZ31 alloy was improved. Fracture mode was evolved from a combination of ductility and brittleness to a sole ductile form. In summary, a CVCDE mold structure with 2 interim dies can improve microstructure, plasticity, and toughness of Mg alloy AZ31.展开更多
基金financially supported by the National Natural Science Foundation of China(No.51205094)
文摘In order to study the influence of die combination on continuous variable cross-section direct extrusion （CVCDE） in the extrusion process, the accumulative strain formula is derived, and it can be known that the extrusion ratio of various stages directly determines the size of corresponding stage strain by formula. In this paper, as an example of the two interim dies, three die combinations of different angles and extrusion ratio are designed. Aviation magnesium alloy ZM6 is studied, and the results show that dynamic recrystallization is even more complete when continuous shear deformation occurs, so that the refinement and homogenization of microstructure are obtained. By the use of different die combinations, the accumulative strain increases under the conditions of same total extrusion ratio. Thus, the refined crystalline strengthening effect of extrusion deformation can be further analyzed. Due to the dead-zone defects, the actual accumulative strain decreases significantly and the effect of microstructure and performance improvements also decreases with it. Therefore, the optimal design of die combination is the key to the process and product of CVCDE, which provides a scientific basis for the development of severe plastic deformation.
基金financial support from the National Natural Science Foundation of China (No. 51675143)
文摘Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and scanning electron microscopy（SEM） were used to observe the variations in microstructure and fracture morphology of Mg alloy AZ31 as a function of processing methods. The results reveal that grains of Mg alloy AZ31 were refined and their microstructure was homogenized by CVCDE. The recrystallization in Mg alloy AZ31 produced by CVCDE with 2 interim dies was more complete than that produced by conventional extrusion（CE） and CVCDE with 1 interim die, and the grains were finer and more uniform.Plasticity of the AZ31 alloy was improved. Fracture mode was evolved from a combination of ductility and brittleness to a sole ductile form. In summary, a CVCDE mold structure with 2 interim dies can improve microstructure, plasticity, and toughness of Mg alloy AZ31.
