Influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds

The influence of submerged entry nozzle clogging on the behavior of molten steel in continuously cast slab molds was studied using commercial code CFX4.3. The results indicate that clogging at the top part of the nozzle port not only increases the velocity of molten steel, but also enhances the wall shear stress, F number and heat flux. This clogging has the greatest effect on the behavior of molten steel. However, clogging at the top 1/3 of the nozzle only increases the velocity of molten steel and has little influence. Clogging at the bottom of the nozzle almost has no influence.

Formation mechanism of internal cracks in continuously cast slab

In order to make clear the formation mechanism of centerline cracks incontinuously cast slabs, the form, distribution and other characteristics of the cracks wereanalyzed. The final solidification point, surface temperature of the slabs and strain in solidifyingshell were investigated. The results were that: (1) Five relatively low temperature zones exist onslab surface below the three water spraying nozzles and near the two edges, respectively, whichcorresponds to the places of centerline cracks and triangle-zone cracks. (2) Centerline cracks andtriangle-zone cracks occur because of weak secondary cooling, uneven cooling along slab width, andlarge variation of roll gap. (3) After minimizing the variation of roll gap and applying the newsecondary cooling pattern, the occurring frequency of centerline and triangle-zone cracks minimizesto zero.

Dynamic Soft Reduction for Continuously Cast Rail Bloom

Center porosity and centerline segregation in continuously cast bloom can be minimized by the well-known method of dynamic soft reduction. Metallurgical results of soft reduction previously employed in continuous bloom casting for heavy rail steel in Panzhihua Iron and Steel Group were not fully achieved because of the improper soft reduction process. Therefore, experiments for optimizing the process parameters of soft reduction for bloom were carried out. The results show that the proportion of the center porosity, which is less than 1.0, increases from 28.41% to 99.81%, while the proportion of the centerline segregation class increases from 40.91% to 100%, and the proportion of the central cavity increases from 92.05% to 100%, whereas the center carbon segregation index decreases from 1.17 to 1.05. The internal quality and the mechanical performance of the rails produced from continuously cast blooms meet the requirement of high-speed tracks of 350 km/h.

Modeling of the Microstructure Evolution in Continuously Cast Al-pb Alloys

A numerical model is presented describing the microstructure evolution of an immiscible alloy under the continuous casting conditions. Calculations are carried out to investigate the microstructure evolution in a vertical strip cast sample of Al+5wt pct Pb alloy. The numerical results show that there exists a peak value for the supersaturation in front of the solid祃iquid interface, and the minority phase droplets are nucleated in a region around this peak. Under strip casting conditions the Marangoni migration dominates the motion of droplets. This leads to an accumulation of the minority phase droplets in front of the solid祃iquid interface.

Analysis of solute redistribution and centerline segregation in continuously cast thin slab

A model has been built to calculate the solute redistribution in continuously cast thin slab and the effect of the fluid flow in mush on the centerline segregation was analyzed. The corresponding simulation program was developed by applying the SIMPLER algorithm. The momentum, energy and species conservation equations were solved simultaneously. The macro-segregation of a 3-D thin slab with 900 mm × 50 mm cross section was simulated. The obtained results show that negative segregation forms near the slab surface and severe centerline segregation forms in the mid-thickness plane. The species concentration in the centerline of the slab increases obviously at the final solidification stage.

NUMERICAL SIMULATION ON SOLIDIFICATION OF HORIZONTALLY CONTINUOUSLY CAST IRON BARS

The solidification process of a horizontally continuously cast gray iron bar of 4.6cm in diame- ter was modelled.The function describing the distribution of heat flux at the internal surface of graphite sleeve,which was equal to that on the surface of the iron bar,was inversely derived using numerical calculation from the temperature distribution in the sleeve measured in real production.By using the distribution of heat flux as a boundary condition on the surface of the iron bar,the numerical simulation on solidification of the iron bar taking longitudinal heat conduction into account was made.The profile of solidification front obtained from the numer- ical simulation was approximately coincident with that in real production.In addition,the quantitative relationships of the thickness of solidified shell at the exit of the mold to the main technological parameters,including the temperature of liquid iron at the entrance of the mold, the moving speed of the bar and the intensity of water cooling,were obtained from the numeri- cal simulation.

Physical Simulation to Determine High TemperatureMechanical Behavior of Continuously Cast Steels

Hot ductility and strength of Continuous casting(CC) steels at elevated temperatures from CC processeswere studied by physical simulation. The method is the hot ductility test. The design of test parameters and datainterpretation are discussed. The results show that the bulging of CC steel slabs which is caused by the mechanismof creep has great influence on the formation of central segregation and internal cracks. Creep tests including staticcreep tests and dynamic creep ones were performed at 1200 and 1300℃. Effects of strain rate and temperature onhot ductility are also discussed and a simple model is presented to explain the interaction between hardening and softening.

Non-metallic Inclusions in Continuously Cast Aluminum Killed Steels

In aluminum killed steels, the size, shape, quantity and formation of non-metallic inclusions in ladle steel (before and after RH vacuum treatment) and in tundish as well as in slabs were studied by EPMA (Electron Probe Microanalysis) and by analyzing the total oxygen. The results showed that in the slabs the total oxygen was quite low and the inclusions discovered were mainly small-sized angular alumina inclusions. This indicates that most inclusions have been removed by floating out during the continuous casting process. In addition, the countermeasures were discussed to decrease the alumina inclusions in the slabs further.

A Model for Diagnosing the Formation of Internal Cracks in Continuously CastSlabs

The internal cracks in continuously cast slabs are attributed to the excessive tensile strain occurring at the solidifying frontduring the continuous casting process. Based on the understanding, a model for diagnosing the formation of the internal cracks was established, in which the strains at the solidifying front caused by' bulging, straightening or unbending, and roll misalignment were calculated and compared with a critical strain value to estimate whether the internal cracks form. Moreover, the established model was appliedto a real slab caster to reveal the distribution of the strains in casting direction and its effect on the internal cracks. It was proved that themodel was reliable and useful for optimizing the operation of continuous casting.

Irregular initial solidification by mold thermal monitoring in the continuous casting of steels:A review

Occasional irregular initial solidification phenomena,including stickers,deep oscillation marks,depressions,and surface cracks of strand shells in continuous casting molds,are important limitations for developing the high-efficiency continuous casting of steels.The application of mold thermal monitoring(MTM) systems,which use thermocouples to detect and respond to temperature variations in molds,has become an effective method to address irregular initial solidification phenomena.Such systems are widely applied in numerous steel companies for sticker breakout prediction.However,monitoring the surface defects of strands remains immature.Hence,indepth research is necessary to utilize the potential advantages and comprehensive monitoring of MTM systems.This paper summarizes what is included in the irregular initial solidification phenomena and systematically reviews the current state of research on these phenomena by the MTM systems.Furthermore,the influences of mold slag behavior on monitoring these phenomena are analyzed.Finally,the remaining problems of the formation mechanisms and investigations of irregular initial solidification phenomena are discussed,and future research directions are proposed.

Microstructure evolution and its influence on thermoplasticity of wide and thick continuous casting slab with heavy reduction

After the heavy reduction(HR)process was carried out at the solidification end of the continuous casting slab,the austenite grains were refined by recrystallization,which improved the thermoplasticity of the slab.However,the reduction in deformation during the HR process initiated stress concentration at the slab surface,and the crack risk increased.To effectively evaluate the risk of slab surface cracks under these complex conditions,the effect of the HR on the austenite recrystallization and thermoplasticity of a microalloyed slab surface was investigated by 15-pass reduction thermal simulation according to the wide and thick slab continuous casting process.The softening fraction was introduced as a global internal variable to quantitatively analyze various recrystallized re-refined grains.After the critical strain reaches the critical strain of dynamic recrystallization,a variety of recrystallization modes alternately occur.Among them,the contribution rate of dynamic crystallization to the later refinement reaches more than 50%.The contribution rates of static recrystallization and metadynamic recrystallization to grain refinement are almost the same.The thermoplasticity of the slab surface first increases and then decreases with increasing reduction pass.It was verified by transmission electron microscopy that the main reason for the decrease in thermoplasticity is that the dislocation multiplication rate increases,resulting in a sharp increase in stress and a decrease in thermoplasticity.

Effect of superheat on quality of central equiaxed grain zone of continuously cast bearing steel billet based on two-dimensional segregation ratio

The quality of central equiaxed grain zone （CEGZ） of GCr15 bearing steel billets was investigated at different superheats （20, 25 and 35 ℃ by experimental observations and a finite element model in order to optimize superheat in continuous casting process. Several GCrl5 billets were collected from the continuous casting shop, and the same CEGZ was chosen for comparison of internal quality of GCrl5 billets. Considering the limitation of segregation index at some points, two- dimensional segregation ratio in CEGZ was introduced. Firstly, the segregation ratio and the area of center large dark points in CEGZ obtain the minimum at 25 ℃ superheat, which indicates that the quality of CEGZ at 25 ~C superheat is improved compared with those at 20 and 35 ℃ superheats for corresponding continuously cast billets. The highest superheat and the lowest superheat are not beneficial for improving the central zone quality in the billets. Secondly, the quality of CEGZ of GCr15 billets increases with a decrease in the secondary dendrite arm spacing of CEGZ. Finally, according to the established finite element model, it is deduced that the secondary dendrite arm spacing of CEGZ is closely related to its later solidifica- tion time at solid fraction of 0.5-1.0, and the former will be decreased when decreasing the latter.

Heat Transfer and Central Segregation of Continuously Cast High Carbon Steel Billet

A numerical model of heat transfer was developed to investigate the heat transfer of continuously cast billet with the aid of surface temperature tests by ThermaCAMTM researcher and nail shooting experiments. The effects of secondary cooling practice and casting speed on the solidification process and central segregation of carbon were investigated as well with the actual central segregation tests. The results show that the surface center and billet center temperatures exhibit a different pattern during solidification, and the solidified shell thickness is presented as an ＂S＂ type. With the increase of secondary cooling intensity and the decrease of casting speed, the end points of the solidus line and the liquidus line move forward, and the central segregation level of carbon decreases. The optimal casting condition is suggested for continuously cast high carbon billet with F-EMS （final electromagnetic stirring）.

Numerical simulation of macrosegregation in continuously cast gear steel 20CrMnTi with final electromagnetic stirring

A 3D/2D hybrid multi-physical-field mathematical model,which takes into consideration the thermosolutal buoyance,was developed to predict the macrosegregation of gear steel 20CrMnTi continuously cast by a curved billet caster with size of 160 mm×160 mm,and investigated the effect of final electromagnetic stirring(F-EMS)on the fluid flow,heat transfer and solute distribution in the liquid core of continuously cast steel.The results show that the application of F-EMS eliminates the effect of thermosolutal buoyancy on the asymmetric distribution of carbon concentration in the cross section of billet and accelerates the final solidification of resident molten steel in the liquid core of strand,but promotes the negative carbon segregation near the billet center.When the gear steel 20CrMnTi is cast at the temperature of 1803 K and speed of 1.7 m/min,the solidification end advances forward from 9.84 to 9.72 m,and center carbon segregation ratio of billet decreases from 1.24 to 1.17 with the increase in current density of F-EMS from 0 to 350 A.

Quality Control for Continuously Cast Slab of High Strength Weathering Steel Q450NQR1

In order to reduce the transverse corner cracks of high strength weathering steel Q450NQR1,the factors influencing transverse corner cracks on continuously cast slab,such as level fluctuation of molten steel in mold,mold taper,primary cooling,mold powder,secondary cooling,nitrogen content in steel,spray nozzle structure,processing parameters and equipment of CC,etc.,were analyzed.Based on this,a series of comprehensive countermeasures have been proposed.The operation shows by the use of key technologies,including stabilizing steel level,optimizing the mold taper,weakening the primary cooling and the secondary cooling,reforming the mold powder,and adjusting spray nozzle structure,the transverse corner cracks on continuously cast slab have been significantly reduced,and the edge cracks on hot rolled sheet have been eliminated due to the transverse corner cracks.The qualified slabs are delivered to produce weathering cold forming sectional steel,whose yield strength is greater than 450MPa.

Forming Conditions and Neural Network Control of Continuously Directional Microstructurein Directional Solidification Continuous Casting Process

Directional solidification continuous casting (DSCC) process is a new manufacturing technology for metallic materials which combines advantages of both directional solidification technology and continuous casting technology. Unlimited long shaped metal with directionally solidifying microstructure can be produced by this process. It is experimentally shown that controlling condition of stable and continuous growth of single crystal structure means the precise control of the location of the S/L interface, which is affected and determined by seven process parameters. Moreover, these parameters are also interacted each other, so the disturbance of any parameters may cause the failure of controlling of S/L interface. In this paper, on the basis of analyzing the forming conditions of continuously directional microstructures in DSCC process, the control model of DSCC procedure by neural network control (NNC) method was proposed and discussed. Combining with the experiments, we first used the computer to simulate the effects of the solidification parameters on destination control variable (S/L interface) and the interactions among these parameters during DSCC procedure. Secondly many training samples necessary for neural network calculation can be obtained through the simulation. Moreover, these samples are inputted into neural network software (NNs) and trained, then the control model can be built up.

Influencing Factors on Center Segregation in Continuously Cast Pipeline Steel Slabs

The factors which influence center segregation of continuously cast slabs are obtained through analyzing the database of macrostructrue. It indicates that center segregation becomes severer with the increasing content of carbon, phosphorus and sulfur; Center segregation will be reduced obviously if the content of manganese is higher than 1.5% and the ratio of Mn/S is higher than 300; High degree of superheat , high casting speed and increasing width of slabs will increase the degree of center segregation. Since center segregation below class B has little effect on the property of steel, hence, in order to low the ratio of center segregation of class B-1.0 down to 10%, several control strategies are presented as follows: the contents of carbon, phosphorus and sulfur must be focalized in lower range of steel grade demanded, but manganese upper operating range control. The referenced contents of the elements in molten steel are required like this: [C]【0.07%,[P]【0.01%,[S]【0.005%,[Mn]】1.5%,[Mn]/[S]】300; The degree of superheat should be lower than 24℃ and the casting speed should be defined to 1.0-1.1 m·min-1. At the same time, proper secondary cooling system of water distribution should be developed and the precision of continuous caster should be also improved.

Formation and control of the surface defect in hypo-peritectic steel during continuous casting:A review

Hypo-peritectic steels are widely used in various industrial fields because of their high strength,high toughness,high processability,high weldability,and low material cost.However,surface defects are liable to occur during continuous casting,which includes depression,longitudinal cracks,deep oscillation marks,and severe level fluctuation with slag entrapment.The high-efficiency production of hypo-peritectic steels by continuous casting is still a great challenge due to the limited understanding of the mechanism of peritectic solidification.This work reviews the definition and classification of hypo-peritectic steels and introduces the formation tendency of common surface defects related to peritectic solidification.New achievements in the mechanism of peritectic reaction and transformation have been listed.Finally,countermeasures to avoiding surface defects of hypo-peritectic steels duiring continuous casting are summarized.Enlightening certain points in the continuous casting of hypo-peritectic steels and the development of new techniques to overcome the present problems will be a great aid to researchers.

Overview of Particles and Bubbles in Continuously Cast Steel

This paper gives an overview of phenomena associated with particles and bubbles in continuously cast steel. During steel processing from deoxidation to solidification the inclusion population undergoes changes with opportunities of removal. Flotation is an important separation mechanism. Inclusion particles may accumulate in the solidifying strand, thus forming enriched bands, which depend on the type of casting machine. Bubbles are created during inert gas injection. They also change in size, can float out, but also form accumulation bands. The interaction of bubbles and particles is discussed. Internal structure that recently has been observed on the inner surface of bubbles will be reviewed.

Real Heat Flux Analysis of Continuously Casting Round Billet

The distributions of heat flux along the height and the circumferential direction of round billet mould were measured continuously.The influence of casting speed,carbon content,powder,and pouring temperature on the average longitudinal and circumferential heat flux in the ＂high heat flux region＂ was discussed.The experimental and analytical results provide a basis for an intelligent mould with online detection of defects,adjustment of operational parameters,optimization of the monitoring system,and even prediction of abnormal heat transfer.