Congestion Control Algorithms for the Internet-A Secondary Publication

In the last five years,there has been a V-shaped recovery in the number of papers on congestion control algorithms on the Internet.In this paper,congestion problems on the Internet are discussed,such as congestion collapse and bufferbloat from the perspective of the necessity of congestion control algorithms.The typical congestion control algorithms are introduced,and the research areas and methods of congestion control algorithms are described.Recent research trends and future prospects of congestion control algorithms are also presented.

Traffic flow of connected and automated vehicles at lane drop on two-lane highway: An optimization-based control algorithm versus a heuristic rules-based algorithm

This paper investigates traffic flow of connected and automated vehicles at lane drop on two-lane highway. We evaluate and compare performance of an optimization-based control algorithm(OCA) with that of a heuristic rules-based algorithm(HRA). In the OCA, the average speed of each vehicle is maximized. In the HRA, virtual vehicle and restriction of the command acceleration caused by the virtual vehicle are introduced. It is found that(i) capacity under the HRA(denoted as C_(H)) is smaller than capacity under the OCA;(ii) the travel delay is always smaller under the OCA, but driving is always much more comfortable under the HRA;(iii) when the inflow rate is smaller than C_(H), the HRA outperforms the OCA with respect to the fuel consumption and the monetary cost;(iv) when the inflow rate is larger than C_(H), the HRA initially performs better with respect to the fuel consumption and the monetary cost, but the OCA would become better after certain time. The spatiotemporal pattern and speed profile of traffic flow are presented, which explains the reason underlying the different performance. The study is expected to help for better understanding of the two different types of algorithm.

Enhanced Perturb and Observe Control Algorithm for a Standalone Domestic Renewable Energy System

The generation of electricity,considering environmental and eco-nomic factors is one of the most important challenges of recent years.In this article,a thermoelectric generator(TEG)is proposed to use the thermal energy of an electric water heater(EWH)to generate electricity independently.To improve the energy conversion efficiency of the TEG,a fuzzy logic con-troller(FLC)-based perturb&observe(P&O)type maximum power point tracking(MPPT)control algorithm is used in this study.An EWH is one of the major electricity consuming household appliances which causes a higher electricity price for consumers.Also,a significant amount of thermal energy generated by EWH is wasted every day,especially during the winter season.In recent years,TEGs have been widely developed to convert surplus or unused thermal energy into usable electricity.In this context,the proposed model is designed to use the thermal energy stored in the EWH to generate electricity.In addition,the generated electricity can be easily stored in a battery storage system to supply electricity to various household appliances with low-power-consumption.The proposed MPPT control algorithm helps the system to quickly reach the optimal point corresponding to the maximum power output and maintains the system operating point at the maximum power output level.To validate the usefulness of the proposed scheme,a study model was developed in the MATLAB Simulink environment and its performance was investigated by simulation under steady state and transient conditions.The results of the study confirmed that the system is capable of generating adequate power from the available thermal energy of EWH.It was also found that the output power and efficiency of the system can be improved by maintaining a higher temperature difference at the input terminals of the TEG.Moreover,the real-time temperature data of Abha city in Saudi Arabia is considered to analyze the feasibility of the proposed system for practical implementation.

Two Adaptive Control Algorithms in Semi-Active Suspension System

To reduce the vibration in the suspension, semi active suspension system was employed. And its CARMA model was built. Two adaptive control schemes, the minimum variance self tuning control algorithm and the pole configuration self tuning control algorithm, were proposed. The former can make the variance of the output minimum while the latter can make dynamic behavior satisfying. The stability of the two schemes was analyzed. Simulations of them show that the acceleration in the vertical direction has been reduced greatly. The purpose of reducing vibration is realized. The two schemes can reduce the vibration in the suspension and have some practicability.

Comparison between iterative wavefront control algorithm and direct gradient wavefront control algorithm for adaptive optics system

Among all kinds of wavefront control algorithms in adaptive optics systems, the direct gradient wavefront control algorithm is the most widespread and common method. This control algorithm obtains the actuator voltages directly from wavefront slopes through pre-measuring the relational matrix between deformable mirror actuators and Hartmann wavefront sensor with perfect real-time characteristic and stability. However, with increasing the number of sub-apertures in wavefront sensor and deformable mirror actuators of adaptive optics systems, the matrix operation in direct gradient algorithm takes too much time, which becomes a major factor influencing control effect of adaptive optics systems. In this paper we apply an iterative wavefront control algorithm to high-resolution adaptive optics systems, in which the voltages of each actuator are obtained through iteration arithmetic, which gains great advantage in calculation and storage. For AO system with thousands of actuators, the computational complexity estimate is about O(n2) ～ O(n3) in direct gradient wavefront control algorithm, while the computational complexity estimate in iterative wavefront control algorithm is about O(n) ～(O(n)3/2), in which n is the number of actuators of AO system. And the more the numbers of sub-apertures and deformable mirror actuators, the more significant advantage the iterative wavefront control algorithm exhibits.

Novel TPN control algorithm for exoatmospheric intercept

A novel control algorithm with fixed pulse thrust, based on true proportional navigation（TPN）, is proposed for exoatmospheric intercept.According to the TPN guidance law and pulse thrust characteristics, the principle of control command is presented, the control stability and precision are analyzed.With the help of the TPN guidance law, the algorithm can automatically modulate the turn-on time and duration of the thrust, which could effectively limit the impact of measure noise of the line-of-sight（LOS） angle and rate on the interception miss-distance.At last, the number-theoretic method（NTM） is introduced to acquire the relation between control algorithm and miss-distance, even as it simulates the intercept process with initial state noise.And the reliability of the algorithm is demonstrated with the simulation result.

Control Algorithm of Electric Vehicle in Coasting Mode Based on Driving Feeling

Coasting in gear is a common driving mode for the conventional vehicle equipped with the internal combustion engine（ICE）, and the assistant braking function of ICE is utilized to decelerate the vehicle in this mode. However, the electric vehicle（EV） does not have this feature in the coasting mode due to the relatively small inertia of the driving motor, so it will cause the driver cannot obtain the similar driving feeling to that of the conventional vehicle, and even a traffic accident may occur if the driver cannot immediately adapt to the changes. In this paper, the coasting control for EV is researched based on the driving feeling. A conventional vehicle equipped with continuously variable transmission（CVT） is taken as the reference vehicle, and the combined simulation model of EV is established based on AVL CRUISE and MATLAB/Simulink. The torque characteristic of the CVT output shaft is measured in coasting mode, and the data are smoothed and fitted to a polynomial curve. For the EV in coasting mode, if the state of charge（SOC） of the battery is below 95%, the polynomial curve is used as the control target for the torque characteristic of the driving motor, otherwise, the required torque is replaced by hydraulic braking torque to keep the same deceleration. The co-simulation of Matlab/Simulink/Stateflow and AVL CRUISE, as well as the hardware-in-loop experiment combined with d SPACE are carried out to verify the effectiveness and the real-time performance of the control algorithm. The results show that the EV with coasting braking control system has similar driving feeling to that of the reference vehicle, meanwhile, the battery SOC can be increased by 0.036% and 0.021% in the initial speed of 100 km/h and 50 km/h, respectively. The proposed control algorithm for EV is beneficial to improve the driving feeling in coasting mode, and it also makes the EV has the assistant braking function.

Study on LQR control algorithm using superelement model

The conventional linear quadratic regulator(LQR) control algorithm is one of the most popular active control algorithms.One important issue for LQR control algorithm is the reduction of structure's degrees of freedom(DOF). In this work, an LQR control algorithm with superelement model is intended to solve this issue leading to the fact that LQR control algorithm can be used in large finite element(FE) model for structure. In proposed model, the Craig-Bampton(C-B) method, which is one of the component mode syntheses(CMS), is used to establish superelement modeling to reduce structure's DOF and applied to LQR control algorithm to calculate Kalman gain matrix and obtain control forces. And then, the control forces are applied to original structure to simulate the responses of structure by vibration control. And some examples are given. The results show the computational efficiency of proposed model using synthesized models is higher than that of the classical method of LQR control when the DOF of structure is large. And the accuracy of proposed model is well. Meanwhile, the results show that the proposed control has more effects of vibration absorption on the ground structures than underground structures.

Application of PI Control Algorithm to Discrete Manufacturing Systems

PI （proportional-integral） control algorithm is applied to control WlP （work-in-progress） in a discrete manufacturing system, where the cascade control of PI controllers is presented. It is in the frequency domain that the PI controller is designed with constraints on sensitivity options to ensure the stability and robustness of its parameters. A case is evaluated on a motorcycle engine crankcase production system, whose simulation results confirm that demand fluctuations can be compensated by PI controllers under a normal demand. PI controllers also possess low sensitivity to the distribution of production times.

Local Bifurcation Analysis of a Delayed Fractional-order Dynamic Model of Dual Congestion Control Algorithms

In this paper, we propose a delayed fractional-order congestion control model which is more accurate than the original integer-order model when depicting the dual congestion control algorithms. The presence of fractional orders requires the use of suitable criteria which usually make the analytical work so harder. Based on the stability theorems on delayed fractionalorder differential equations, we study the issue of the stability and bifurcations for such a model by choosing the communication delay as the bifurcation parameter. By analyzing the associated characteristic equation, some explicit conditions for the local stability of the equilibrium are given for the delayed fractionalorder model of congestion control algorithms. Moreover, the Hopf bifurcation conditions for general delayed fractional-order systems are proposed. The existence of Hopf bifurcations at the equilibrium is established. The critical values of the delay are identified, where the Hopf bifurcations occur and a family of oscillations bifurcate from the equilibrium. Same as the delay, the fractional order normally plays an important role in the dynamics of delayed fractional-order systems. It is found that the critical value of Hopf bifurcations is crucially dependent on the fractional order. Finally, numerical simulations are carried out to illustrate the main results. © 2017 Chinese Association of Automation.

APPLICATION OF PREDICTIVE CONTROL ALGORITHM IN SPEED CONTROL SYSTEM

In view of DC speed control system, this paper presents a predictive control algorithm to replace traditional PID control. System predictive model requires little information of the controlled object, and because it adopts rolling optimum method, system

Study of improved gray predictive PID control algorithm

According to these characteristics of the movement of the special platform servo,a new improved grey predictive PID control algorithm was proposed based on the grey predictive PID,and then the algorithm was simulated by MATLAB.As a result that it can improve the response speed and stability of the system,and meet the demand of the system.

A Review of Control Algorithms for Autonomous Quadrotors

The quadrotor unmanned aerial vehicle is a great platform for control systems research as its nonlinear nature and under-actuated configuration make it ideal to synthesize and analyze control algorithms. After a brief explanation of the system, several algorithms have been analyzed including their advantages and disadvantages: PID, Linear Quadratic Regulator (LQR), Sliding mode, Backstepping, Feedback linearization, Adaptive, Robust, Optimal, L1, H∞, Fuzzy logic and Artificial neutral networks. The conclusion of this work is a proposal of hybrid systems to be considered as they combine advantages from more than one control philosophy.

Improved ON-OFF Semi-active Control Algorithm and Its Performance Simulation Analysis

To improve the switching time of the control force in standard sky-hook ON-OFF semi-active control algorithm,a stateadjust coefficient was adopted in the improved ON-OFF( ION-OFF)algorithm. In considering of the riding comfort and the handling stability of vehicle, a comprehensive performance assessment criterion on suspension system was established with the utilization of the corresponding passive suspension system. Several simulations and analyses were conducted on improved ON-OFF semi-active suspension system with the comparison of passive suspension system and ON-OFF semi-active suspension system. The simulation results showed that the optimal comprehensive performance of the improved ON-OFF suspension system could be achieved when the state-adjust coefficient equalled 0. 6 as the vehicle running on C level road with the speed of 10 m/s,and the comprehensive performance was better than ON-OFF suspension system. Conclusions could be drawn from the frequency domain analysis that the performance of riding comfort and handling stability were both improved in the low resonance frequency and the mid-frequency range. The fact could be known that the comprehensive performance of the suspension system was associated with the frequency of the riding road and the sprung mass( SM) with the analysis of affecting factors.

HUMAN-SIMULATING VEHICLE STEERING CONTROL ALGORITHM

A new vehicle steering control algorithm is presented. Unlike the traditional methods do, the algorithm uses a sigmoid function to describe the principle of the human driver＇s steering strategy. Based on this function, a human simulating vehicle steering model, human-simulating steering control（HS） algorithm is designed. In order to improve the adaptability to different environments, a parameter adaptive adjustment algorithm is presented. This algorithm can online modify the value of the key parameters of the HS real time. HS controller is used on a vehicle equipped with computer vision system and computer controlled steering actuator system, the result from the automatic vehicle steering experiment shows that the HS algorithm gives good performance at different speed, even at the maximum speed of 172 km/h.

Simulation research on control algorithm of differential pressure casting process

To improve the precision of the filling pressure curve of differential pressure casting controlled with PID controller,the model of differential pressure casting process is established and two pressure-difference control systems using PID algorithm and Dahlin algorithm are separately designed in MATLAB. The scheduled pressure curves controlled with PID algorithm and Dahlin algorithm,respectively,are comparatively simulated in MATLAB. The simulated pressure curves obtained show that the control precision with Dahlin algorithm is higher than that with PID algorithm in the differential pressure casting process,and it was further verified by production practice.

Distributed Cooperative Control Algorithm for Multi-UAV Mission Rendezvous

Multiple unmanned aerial vehicles(UAVs)cooperative operation is the main form for UAVs fighting in battlefield,and multi-UAV mission rendezvous is the premise of cooperative reconnaissance and attack missions.We propose a rendezvous control strategy,which divides the rendezvous process into two parts:The loose formation rendezvous and the close formation rendezvous.In the first stage,UAVs are supposed to reach the specific target locations simultaneously and form a loose formation.A distributed control strategy based on first-order consensus algorithm is presented to achieve this goal.Then the second stage is designed based on the second-order consensus algorithm to complete the transition from the loose formation to the close formation.This process needs the speeds and heading angles of UAVs to reach an agreement.Besides,control algorithms with a virtual leader are proposed,by which the formation states can reach a specific value.Finally,simulation results show that the control algorithms are capable of realizing the mission rendezvous of multi-UAV and the consistence of UAVs′final states,which verify the effectiveness and feasibility of the designed control strategy.

Comparison of Different Control Algorithms for a Gantry Crane System

For a gantry crane system, this paper presents a comparison between four control algorithms. These algo-rithms are being compared on simplicity, stability and robustness. Goal for the controller is to move the load on a gantry crane to a new position with minimal overshoot of the load and maximal speed of the load. An-other goal is to provide an insight in the behaviour of the possible controllers. In this article a parallel P-controller, cascade P-controller, fuzzy controller and an internal model controller are used. To be able to validate and design the controllers a model is derived from the gantry crane. The controllers and the model are being implemented in Matlab Simulink. Finally the controllers are validated and tuned in Labview on a laboratory gantry scrane scale model. Main conclusion is that all presented controllers can be used as a con-troller for the gantry crane system but the fuzzy controller is showing the best performance.

Research on Double Cascade Control Algorithm for Self-Balancing Two-Wheeled Vehicle

To solve the problem of self-balancing two-wheeled vehicle, this article presents double cascade PID control algorithm. This method reduces the coupling of balance control, speed control and direction control, because of the special system structure. This article successfully solved the sensor fusion of gyroscope and accelerometer by using Kalman filtering algorithm, and adding in fuzzy PID algorithm to improve the flexibility of the steering system, thus greatly improving the accuracy and response rate of the system.

Implementation of Control Algorithms in Small Embedded Systems

This work describes how a control algorithm can be implemented in a small (8-bit) microcontroller for the main purpose of merging embedded systems and control theory in electrical engineering undergraduate classes. Two different methods for discretizing the control expression are compared: Euler transformation and bilinear transformation. The sampling rate’s impact on the algorithm is discussed and theoretical results are verified by an application to a temperature control system in a heating plant. Four control algorithms are compared: PID and PI algorithms discretized with Euler and bilinear transformation, respectively. It is shown that for the heating plant used in this work, a bilinear PI algorithm implemented in a small 8-bit microcontroller outperforms a commercial controller from Panasonic. It is also demonstrated that all the derived algorithms can be implemented using integer calculations only, obviating the need for expensive and time-consuming floating-point calculations. This work bridges the gap between control theory equations and the implementation of control systems in small embedded systems with no inherent floating-point processing power.