A model following adaptive control system for CSIM is presented in this paper. A dynamic mathematical model of slip control based system is obtained. With the help of model reducing technique, full order model is ...A model following adaptive control system for CSIM is presented in this paper. A dynamic mathematical model of slip control based system is obtained. With the help of model reducing technique, full order model is reduced to simplify the design without degrading much of the performance. Model following adaptive control laws in discrete form are derived. These laws satisfy the hyperstability condition for taking care of the load and machine parameter changes of the drive. A microprocessor 8098 is used to develop the speed controller. The implementation of the control system uses only available variables of the reference model and the controlled plant. Experimental results are given to demonstrate the good performance of the system.展开更多
A new kind of simple and flexible CO2 welding system was developed to carry out waveform control. The system consisted of IGBT inverter, PWM circuit and microprocessor unit （ MPU） , in which the output current of co...A new kind of simple and flexible CO2 welding system was developed to carry out waveform control. The system consisted of IGBT inverter, PWM circuit and microprocessor unit （ MPU） , in which the output current of constant current （CC） power supply could be changed according to transient physical state, and the variable down slope rate control could be used to ensure a stable welding process. The welding experiment results proved the effectiveness of this control approach.展开更多
In this paper the authors present an analysis and the implementation of microprocessor-baseddigital phase-locked loop speed control system for an induction motor which is actuated by aSPWM-GTR inverter.The system is c...In this paper the authors present an analysis and the implementation of microprocessor-baseddigital phase-locked loop speed control system for an induction motor which is actuated by aSPWM-GTR inverter.The system is controlled by a 16-bit single chip microprocessor.A new type of frequency and phase detector is presented in detail,An adaptive method isadopted in speed controller.A three mode control scheme is used.These techniques are very use-ful to the improvement of the dynamic behavior of digital AC motor drive system.Experimental results show that the system is of good stability,high precision and good dynam-ic performance.展开更多
This paper introduces a SF vector control system of a slip frequency controlled induction mo-tor with simple structure,fair performance and convenient operation.It is realized by two singlechip microprocessors and fed...This paper introduces a SF vector control system of a slip frequency controlled induction mo-tor with simple structure,fair performance and convenient operation.It is realized by two singlechip microprocessors and fed from SPWM-GTR inverter.The whole system is combined by twosubsystems,both of them are 8031 single chip microprocessors.The communication between themis coordinated by the full duplex serial port within the chip and ask-and-answer communicationmanner.The error-corrected means adopted has improved the operation reliability of the system.A series of experimental results on a 3 kW induction motor are given at the end of this paper.展开更多
UV wavelength auto-tuned tuned output system is realized by the difference method. Controlled by the microprocessor, output wavelength auto- tracking is achieved.Besides, equipment self-checking auto-positioning and t...UV wavelength auto-tuned tuned output system is realized by the difference method. Controlled by the microprocessor, output wavelength auto- tracking is achieved.Besides, equipment self-checking auto-positioning and temperature correct are realized,The wavelength tuned output efficiency in the experiment is better than 97 %.展开更多
The paper introduces a temperature control systembased on AT89C51 single-chip-microprocessor, and discussesthe principle , hardware structure, and software design of thissystem in detail.
With the development of Ethernet systems and the growing capacity of modem silicon technology, embedded communication networks are playing an increasingly important role in embedded and safety critical systems. Hardwa...With the development of Ethernet systems and the growing capacity of modem silicon technology, embedded communication networks are playing an increasingly important role in embedded and safety critical systems. Hardware/software co-design is a methodology for solving design problems in processor based embedded systems. In this work, we implemented a new 1-cycle pipeline microprocessor and a fast Ethemet transceiver and established a low cost, high performance embedded network controller, and designed a TCP/IP stack to access the Intemet. We discussed the hardware/software architecture in the forepart, and then the whole system-on-a-chip on Altera Stratix EP1S25F780C6 device. Using the FPGA environment and SmartBit tester, we tested the system＇s throughput. Our simulation results showed that the maximum throughput of Ethemet packets is up to 7 Mbps, that of UDP packets is up to 5.8 Mbps, and that of TCP packets is up to 3.4 Mbps, which showed that this embedded system can easily transmit basic voice and video signals through Ethemet, and that using only one chip can realize that many electronic devices access to the Intemet directly and get high performance.展开更多
文摘A model following adaptive control system for CSIM is presented in this paper. A dynamic mathematical model of slip control based system is obtained. With the help of model reducing technique, full order model is reduced to simplify the design without degrading much of the performance. Model following adaptive control laws in discrete form are derived. These laws satisfy the hyperstability condition for taking care of the load and machine parameter changes of the drive. A microprocessor 8098 is used to develop the speed controller. The implementation of the control system uses only available variables of the reference model and the controlled plant. Experimental results are given to demonstrate the good performance of the system.
基金Supported by Research Project of Henan Science and Technology Foundation(0124110209,0211061900).
文摘A new kind of simple and flexible CO2 welding system was developed to carry out waveform control. The system consisted of IGBT inverter, PWM circuit and microprocessor unit （ MPU） , in which the output current of constant current （CC） power supply could be changed according to transient physical state, and the variable down slope rate control could be used to ensure a stable welding process. The welding experiment results proved the effectiveness of this control approach.
文摘In this paper the authors present an analysis and the implementation of microprocessor-baseddigital phase-locked loop speed control system for an induction motor which is actuated by aSPWM-GTR inverter.The system is controlled by a 16-bit single chip microprocessor.A new type of frequency and phase detector is presented in detail,An adaptive method isadopted in speed controller.A three mode control scheme is used.These techniques are very use-ful to the improvement of the dynamic behavior of digital AC motor drive system.Experimental results show that the system is of good stability,high precision and good dynam-ic performance.
文摘This paper introduces a SF vector control system of a slip frequency controlled induction mo-tor with simple structure,fair performance and convenient operation.It is realized by two singlechip microprocessors and fed from SPWM-GTR inverter.The whole system is combined by twosubsystems,both of them are 8031 single chip microprocessors.The communication between themis coordinated by the full duplex serial port within the chip and ask-and-answer communicationmanner.The error-corrected means adopted has improved the operation reliability of the system.A series of experimental results on a 3 kW induction motor are given at the end of this paper.
文摘UV wavelength auto-tuned tuned output system is realized by the difference method. Controlled by the microprocessor, output wavelength auto- tracking is achieved.Besides, equipment self-checking auto-positioning and temperature correct are realized,The wavelength tuned output efficiency in the experiment is better than 97 %.
文摘The paper introduces a temperature control systembased on AT89C51 single-chip-microprocessor, and discussesthe principle , hardware structure, and software design of thissystem in detail.
文摘With the development of Ethernet systems and the growing capacity of modem silicon technology, embedded communication networks are playing an increasingly important role in embedded and safety critical systems. Hardware/software co-design is a methodology for solving design problems in processor based embedded systems. In this work, we implemented a new 1-cycle pipeline microprocessor and a fast Ethemet transceiver and established a low cost, high performance embedded network controller, and designed a TCP/IP stack to access the Intemet. We discussed the hardware/software architecture in the forepart, and then the whole system-on-a-chip on Altera Stratix EP1S25F780C6 device. Using the FPGA environment and SmartBit tester, we tested the system＇s throughput. Our simulation results showed that the maximum throughput of Ethemet packets is up to 7 Mbps, that of UDP packets is up to 5.8 Mbps, and that of TCP packets is up to 3.4 Mbps, which showed that this embedded system can easily transmit basic voice and video signals through Ethemet, and that using only one chip can realize that many electronic devices access to the Intemet directly and get high performance.
