Microstructure-Properties Correlation of Dual Phase Steels Produced by Controlled Rolling Process

The purpose of this research is to quantify the effects of compositional and processing parameters on the microstruc-ture and properties of dual phase steel produced directly by hot rolling and rapid cooling. Steels with the base composition of 0.1%C, 1.4%Si, and 1.0%Mn with additions of 0.5%Cr to influence hardenability, 0.04%Nb to retard recrystallization in the latter stages of rolling, or 0.02%Ti to inhibit grain growth during and after reheating were investigated. Investigation was made to predict microstructure evolution and to correlate microstructure with processing parameters. The effects of the important microstructure parameters such as ferrite grain size, martensite volume fraction (VM) and morphology (polygonal or fibrous) on the tensile and impact properties are discussed. Multiple linear regression analysis of the ultimate tensile strength has shown that, increasing VM and martensite microhardness and grain refinement of ferrite are the major contributions to increase the strength of the steel. It was found that the dual-phase steel produced by controlled rolling process, with a microstructure which consisted of fine grained ferrite (4 um) and 35%~40% fibrous martensite, presented optimum tensile and impact properties because of enhanced resistance to crack propagation.

STRAIN-INDUCED ISOTHERMAL PRECIPITATION OF Nb,V AND Ti CARBONITRIDES IN MICROALLOYED STEELS DURING CONTROLLED ROLLING

The strain-induced isothermal precipitation and the law of coarsening of Nb,V and Ti carbonitrides in Nb-steel.V-steel.Nb-V steel and Ti-V-Nb steel have been investigated systematically by means of STEM,EDAX,a new extraction replica technique and the quanti- tative phase analyses method.

Research and Application of Non-symmetrical Roll Bending Control of Cold Rolling Mill

The existing research of the flatness control for strip cold rolling mainly focuses on the calculation of the optimum adjustment of individual flatness actuator in accordance with the flatness deviation, which can be used for general flatness control. However, it does not work for some special rolling processes, such as the elimination of ultra single side edge-waves and the prevention of strip break due to tilting roll control overshooting. For the purpose of solving these problems, the influences of non-symmetrical work roll bending and intermediate roll bending on flatness control were analyzed by studying efficiencies of them. Moreover, impacts of two kinds of non-symmetrical roll bending control on the pressure distribution between rolls were studied theoretically. A non-symmetrical work roll bending model was developed by theoretical analysis in accordance with practical conditions. The model was applied to the revamp of a 1250 6-H reversible universal crown mill (UCM) cold mill. Theoretical study and practical applications show that the coordination utilization of the non-symmetrical work roll bending control and tilting roll control was effective in flatness control when there appeared bad strip single side edge waves, especially when the incoming strip was with a wedge shape. In addition, the risk of strip break due to tilting control overshooting could be reduced. Furthermore, the non-symmetrical roll bending control can reduce the extent of uneven distribution of pressure between rolls caused by intermediate roll shifting in flatness control and slow down roll wear. The non-symmetrical roll bending control technology has important theoretical and practical significance to better flatness control.

Austenite Recrystallization and Controlled Rolling of Low Carbon Steels

The dynamic recrystallization and static recrystallization in a low carbon steel were investigated through single-pass and double-pass experiments. The results indicate that as the deformation temperature increases and the strain rate decreases, the shape of the stress-strain curve is changed from dynamic recovery shape to dynamic recrystallization shape. The austenite could not recrystallize within a few seconds after deformation at temperature below 900 ℃. According to the change in microstructure during deformation, the controlled rolling of low carbon steel can be divided into four stages： dynamic recrystallization, dynamic recovery, strain-induced ferrite transformation, and rolling in two-phase region. According to the microstructure after deformation, the controlled rolling of low carbon steel can be divided into five regions： non-recrystallized austenite, partly-recrystallized austenite, fully-recrystallized austenite, austenite to ferrite transformation, and dual phase.

Controlled Rolling and Cooling Process for Low Carbon Cold Forging Steel

Effect of controlled rolling and cooling process on the mechanical properties of low carbon cold forging steel was investigated for different processing parameters of a laboratory hot rolling mill. The results show that the specimens with fast cooling after hot rolling exhibit very good mechanical properties, and the improvement of the mechanical properties can be attributed mainly to the ferrite-grain refinement. The mechanical properties increase with decreasing final cooling temperature within the range from 670 ℃ to 570 ℃ due to the finer interlamellar spacing of pearlite colony. The specimen with fast cooling after low temperature rolling shows the highest values of the mechanical properties. The effect of the ferrite grain size on the mechanical properties was greater than that of pearlite morphology in the present study. The mechanical properties of specimens by controlled rolling and cooling process without thermal treatment were greatly superior to that of the same specimens by the conventional rolling, and their tensile strength reached 490 MPa grade even in the case of low temperature rolling without controlled rolling. It might be expected to realize the substitution medium-carbon by low-carbon for 490 MPa grade cold forging steel with controlled rolling and cooling process.

Optimization of Holding Temperature and Holding Thickness for Controlled Rolling on Plate Mill

Holding temperature and holding thickness are main parameters for two-phase controlled rolling on plate mill. The optimization of holding temperature and holding thickness for pass schedule calculation of two-phase controlled rolling on plate mill was presented and its feature is as follows： （1） Determination of holding thickness can be automatically obtained based on the influence of mill safety limits, tracking zone length and holding time on holding thickness; （2） Determination of holding temperature can be automatically obtained and the holding time can be reduced as much as possible; （3） Algorithm can modify the holding temperature and thickness depending on slab size and product size.

EFFECT OF THE CONTROLLED ROLLING CONTROLLED COOLING ON STRENGTH AND DUCTILITY OF THE BAINITE MICRO ALLOYED ENGINEERING STEEL

The continuous cooling transformation of hot deformation austenite austenite of test steel and the effect of different processing schedules of controlled rolling and controlled cooling on the strength and ductility have been studied. The theory and the experiment base are presented for controlled rolling and controlled cooling of the SBL micro alloyed engineering steel.

Rolling Control Characteristic Experimental Investigation of a Canard Missile with Free-Spinning Tail

To study the rolling control characteristics of a canard-controlled missile, a series of wind tunnel experiment is conducted. The experimental method, the structure features of wind tunnel model and the experimental results are introduced in this paper. The experimental data show that the canard is an inefficient rolling control device for canard-controlled missile with fixed tail fins; but for the free-spinning tail fin configuration, the canard can conduct rolling control of the missile, and even have higher controlling efficiency under larger canard deflection angle.

Effect of controlled rolling on the martensitic hardenability of dual phase steel

The C-Mn and C-Mn-Nb steels were thermo-mechanically processed to develop dual phase steel and to study the effect of controlled rolling on the martensitic hardenability of austenite. The steel specimens were intercritically annealed at 790℃, rolled at that temperature to the reductions of 10%, 23%, and 47% and immediately cooled at different rates. Quantitative metallography was used to construct the microstructure map, which illustrated that increasing deformation progressively reduced the proportion of new ferrite formed at all cooling rates and increased the amount of martensite at fast and intermediate rates. The martensitic hardenability of austenite remaining after all the rolling reductions was plotted as a function of cooling rates. It was observed that for the austenite-martensite conversion efficiencies greater than about 25%, controlled rolling increased the martensitic hardenability of austenite.

DECOUPLED MODEL FOR FLATNESS CONTROL IN 4-H CVC COLD ROLLING MILLS

ＩＮＴＲＯＤＵＣＴＩＯＮＴｈｅｐｒｅｃｉｓｅｃｏｎｔｒｏｌｏｆｒｏｌｇａｐｉｎ４ｈＣＶＣｍｉｌｓｉｓｐａｒｔｉｃｕｌａｒｌｙｄｉｆｉｃｕｌｔｄｕｅｔｏｔｈｅｃｏｍｐｌｅｘｉｎｔｅｒａｃｔｉｏｎｓｂｅｔｗｅｎｗｏｒｋｒｏｌｓｈｉｆｔｉｎｇａｎｄｂｅｎ...

Adaptive neuro-fuzzy interface system for gap acceptance behavior of right-turning vehicles at partially controlled T-intersections

Gap acceptance theory is broadly used for evaluating unsignalized intersections in developed coun tries. Intersections with no specific priority to any move ment, known as uncontrolled intersections, are common in India. Limited priority is observed at a few intersections, where priorities are perceived by drivers based on geom etry, traffic volume, and speed on the approaches of intersection. Analyzing such intersections is complex because the overall traffic behavior is the result of drivers, vehicles, and traffic flow characteristics. Fuzzy theory has been widely used to analyze similar situations. This paper describes the application of adaptive neurofuzzy interface system （ANFIS） to the modeling of gap acceptance behavior of rightturning vehicles at limited priority Tintersections （in India, vehicles are driven on the left side of a road）. Field data are collected using video cameras at four Tintersections having limited priority. The data extracted include gap/lag, subject vehicle type, conflicting vehicle type, and driver＇s decision （accepted/rejected）. ANFIS models are developed by using 80 % of the extracted data （total data observations for major road right turning vehicles are 722 and 1,066 for minor road right turning vehicles） and remaining are used for model vali dation. Four different combinations of input variables are considered for major and minor road right turnings sepa rately. Correct prediction by ANFIS models ranges from 75.17 % to 82.16 % for major road right turning and 87.20 % to 88.62 % for minor road right turning. Themodels developed in this paper can be used in the dynamic estimation of gap acceptance in traffic simulation models.

Research and Development Trend of Shape Control for Cold Rolling Strip

Shape is an important quality index of cold rolling strip. Up to now, many problems in the shape control domain have not been solved satisfactorily, and a review on the research progress in the shape control domain can help to seek new breakthrough directions. In the past 10 years, researches and applications of shape control models, shape control means, shape detection technology, and shape con- trol system have achieved significant progress. In the aspect of shape control models, the researches in the past improve the accuracy, speed and robustness of the models. The intelligentization of shape control models should be strengthened in the future. In the aspect of the shape control means, the researches in the past focus on the roll opti- mization, mill type selection, process optimization, local strip shape control, edge drop control, and so on. In the future, more attention should be paid to the coordination control of both strip shape and other quality indexes, and the refinement of control objective should be strengthened. In the aspects of shape detection technology and shape control system, some new types of shape detection meters and shape control systems are developed and have successfully indus- trial applications. In the future, the standardization of shape detection technology and shape control system should be promoted to solve the problem of compatibility. In general,the four expected development trends of shape control for cold roiling strip in the future are intelligentization, coordi- nation, refinement, and standardization. The proposed research provides new breakthrough directions for improv- ing shape quality.

STUDY ON COUPLING MODEL OF (SEEPAGE-FIELD) AND STRESS-FIELD FOR ROLLED CONTROL CONCRETE DAM

Based on the construction interfaces in rolled control concrete dam(RCCD), the methods were proposed to calculate the influence thickness of construction interfaces and the corresponding physical mechanics parameters. The principle on establishing the coupling model of seepage_field and stress_field for RCCD was presented. A 3_D Finite Element Method(FEM) program was developed. Study shows that such parameters as the thickness of construction interfaces,the elastic ratio and the (Poisson's) ratio obtained by tests and theoretical analysis are more reasonable, the coupling model of seepage_field and stress_field for RCCD may indicate the coupling effect between the two fields scientifically, and the developed 3_D FEM program can reflect the effect of the construction interfaces more adequately. According to the study, many scientific opinions are given both to analyze the influence of the construction interfaces to the (dam's) characteristic, and to reveal the interaction between the stress_field and the seepage_field.

Three-dimensional Construction and Omni-directional Rolling Analysis of a Novel Frame-like Lattice Modular Robot

Lattice modular robots possess diversity actuation methods, such as electric telescopic rod, gear rack, magnet, robot arm, etc. The researches on lattice modular robots mainly focus on their hardware descriptions and reconfiguration algorithms. Meanwhile, their design architectures and actuation methods perform slow telescopic and moving speeds, relative low actuation force verse weight ratio, and without internal space to carry objects. To improve the mechanical performance and reveal the locomotion and reconfiguration binary essences of the lattice modular robots, a novel cube-shaped, frame-like, pneumatic-based reconfigurable robot module called pneumatic expandable cube（PE-Cube） is proposed. The three-dimensional（3D） expanding construction and omni-directional rolling analysis of the constructed robots are the main focuses. The PE-Cube with three degrees of freedom（Do Fs） is assembled by replacing the twelve edges of a cube with pneumatic cylinders. The proposed symmetric construction condition makes the constructed robots possess the same properties in each supporting state, and a binary control strategy cooperated with binary actuator（pneumatic cylinder） is directly adopted to control the PE-Cube. Taking an eight PE-Cube modules＇ construction as example, its dynamic rolling simulation, static rolling condition, and turning gait are illustrated and discussed. To testify telescopic synchronization, respond speed, locomotion feasibility, and repeatability and reliability of hardware system, an experimental pneumatic-based robotic system is built and the rolling and turning experiments of the eight PE-Cube modules＇ construction are carried out. As an extension, the locomotion feasibility of a thirty-two PE-Cube modules＇ construction is analyzed and proved, including dynamic rolling simulation, static rolling condition, and dynamic analysis in free tipping process. The proposed PE-Cube module, construction method, and locomotion analysis enrich the family of the lattice modular robot and provide the instruction to design the lattice modular robot.

Recrystallization model for hot-rolling of 5182 aluminum alloy

A recrystallization model for hot rolling of 5182 aluminum alloy was presented by means of the fractional softening during double interval deformation. It is found that the recrystallization rate depends on strain rate more sensitively than deformation temperature, and the time for full recrystallization is very short as strain rate is greater than 1?s -1 . Using the recrystallization—time—temperature curves, the desirable hot rolled microstructure can be obtained by controlling the rolling speed, temperature and cooling rate before cooling during the last pass in reversing mill.[

An Expert System in Automatic Gauge Control for Rolling Process

Beacuse the practical mathematic model of rolling process can't be built accurately,this paper established an expert system to control the rolling steels' gauge by adjusting the setup roll open, which combined the experience of theoreticians and operators. The system applied the expression method of rule-skeleton+rule-body', and selected an appropriate non-exact reference model and self-study algorithm. The whole system, including auxiliary routes, is designed in Borland C++. Some experiments on this system have been done, and a good result has been achieved.

Roll System and Stock's Multi-parameter Coupling Dynamic Modeling Based on the Shape Control of Steel Strip

The existence of rolling deformation area in the rolling mill system is the main characteristic which dis- tinguishes the other machinery. In order to analyze the dynamic property of roll system＇s flexural deformation, it is necessary to consider the transverse periodic movement of stock in the rolling deformation area which is caused by the flexural deformation movement of roll system simul- taneously. Therefore, the displacement field of roll system and flow of metal in the deformation area is described by kinematic analysis in the dynamic system. Through intro- ducing the lateral displacement function of metal in the deformation area, the dynamic variation of per unit width rolling force can be determined at the same time. Then the coupling law caused by the co-effect of rigid movement and flexural deformation of the system structural elements is determined. Furthermore, a multi-parameter coupling dynamic model of the roll system and stock is established by the principle of virtual work. More explicitly, the cou- pled motion modal analysis was made for the roll system. Meanwhile, the analytical solutions for the flexural defor- mation movement＇s mode shape functions of rolls are discussed. In addition, the dynamic characteristic of the lateral flow of metal in the rolling deformation area has been analyzed at the same time. The establishment ofdynamic lateral displacement function of metal in the deformation area makes the foundation for analyzing the coupling law between roll system and rolling deformation area, and provides a theoretical basis for the realization of the dynamic shape control of steel strip.

Technological investigation on the Short Stroke Width Control Rolling in the Rougher Mills of Hot Strip Continuous Rolling Mill Train

According to technological requirement of hot charge rolling and hot direct rolling,in this paper,we investigated the technology of the width control rolling in the rougher mills of hot strip continuous rolling mill train.On the basis of improving width range of continuous casting of slab,we obtained a good result of greatly increasing the yield of slab→coil is achieved.

Study and application of crown feedback control in hot strip rolling

Crown feedback control is one part of the automatic shape control （ASC） system. On the basis of large simulation researches conducted, a linear crown feedback control model was put forward and applied in actual strip rolling. According to its successful op- eration in the ASP 1700 hot strip mill of Angang Group for one year and also from the statistical results of several crown measurements, it can be definitely said that this control model is highly effective and shows stable performance. The control effectiveness of different gauges of strips with the feedback control is found to increase by 10%-30% compared with that without feedback control.

Short Stroke Control with Gaussian Curve and PSO Algorithm in Plate Rolling Process

The precision width control is vital for product quality and production economy in plate width control process, so short stroke control method was used in plate rolling by opening or closing edger gap so as to avoid head end necking. Head end necking on different broadening ratio was analyzed, and sections of different elongations at edger roiling was calculated; based on the law of volume constancy, the adjustment functions were described by parabolic functions. Control curves were developed with three Gaussian curves by means of additional combining; SSC control curve was changed with different weights of those curves, w1 effect one-third of SSC length, w2 effect two-third of SSC length, w3 effect all three parts of SSC length. In order to adjust the amount of weights for precise quantification, PSO algorithm was used to build sufficiency function so as to obtain best rectangular degree by global optimization. Practical applications showed that the method proposed is available to improve the product rolling yields by 1.0% -2. 0% and worthy to apply to plate rolling.