Alcohol-assisted low-temperature methanol synthesis was conducted over Cu/ZnO;catalysts while varying the copper content（X）. Unlike conventional methanol synthesis, ethanol acted as both solvent and reaction interme...Alcohol-assisted low-temperature methanol synthesis was conducted over Cu/ZnO;catalysts while varying the copper content（X）. Unlike conventional methanol synthesis, ethanol acted as both solvent and reaction intermediate in this reaction, creating a different reaction pathway. The formation of crystalline phases and characteristic morphology of the co-precipitated precursors during the co-precipitation step were important factors in obtaining an efficient Cu/ZnO catalyst with a high dispersion of metallic copper,which is one of the main active sites for methanol synthesis. The acidic properties of the Cu/ZnO catalyst were also revealed as important factors, since alcohol esterification is considered the rate-limiting step in alcohol-assisted low-temperature methanol synthesis. As a consequence, bifunctionality of the Cu/ZnO catalyst such as metallic copper and acidic properties was required for this reaction. In this respect, the copper content（X） strongly affected the catalytic activity of the Cu/ZnO;catalysts, and accordingly, the Cu/ZnO;.5 catalyst with a high copper dispersion and sufficient acid sites exhibited the best catalytic performance in this reaction.展开更多
The copper contents and its existing forms in the slags during the slag-making stage of Peirce-Smith converters in Guixi Smelter, Jiangxi Province, China have been investigated. The investigation was based on plant tr...The copper contents and its existing forms in the slags during the slag-making stage of Peirce-Smith converters in Guixi Smelter, Jiangxi Province, China have been investigated. The investigation was based on plant trials with the corresponding thermodynamic calculations and kinetic considerations. From the plant data, the total copper content in the slags was in the range of 2% to 8% (mass fraction). The mechanical entrainment of matte drops has been found to be the main cause of the copper loss. The suspension index, defined as the ratio of the mass fraction of copper in suspended matte drops in the slag to that in bulk of the matte phase, has been adopted to quantify the matte entrainment. The values of this parameter estimated in this work have been found mainly within a range of 2.5%-8.0%. The Fe3O4 content in the slag has been estimated to be the most important factor, among others, influencing the separation of slag with matte and, consequently, the copper loss from the slag.展开更多
Metallic hollow spheres are used as base materials in the manufacture of hollow sphere structures and metallic foams. In this study, steel hollow spheres were successfully manufactured using an advanced powder metallu...Metallic hollow spheres are used as base materials in the manufacture of hollow sphere structures and metallic foams. In this study, steel hollow spheres were successfully manufactured using an advanced powder metallurgy technique. The spheres＇ shells were characterized by optical microscopy in conjunction with microstructural image analysis software, scanning electron microscopy（SEM）, energy-dispersive X-ray spectroscopy（EDX）, and X-ray diffraction（XRD）. The microscopic evaluations revealed that the shells consist of sintered iron powder, sintered copper powder, sodium silicate, and porosity regions. In addition, the effects of copper content on various parameters such as shell defects, microcracks, thickness, and porosities were investigated. The results indicated that increasing the copper content results in decreases in the surface fraction of shell porosities and the number of microcracks and an increase in shell thickness.展开更多
Five sets of high entropy alloys(HEAs)FeCoNiCu_(x)(x=0.5,1.0,1.5,2.0,2.5)were produced by vacuum induction smelting.The effects of Cu content on the microstructure and mechanical properties of the alloys were interrog...Five sets of high entropy alloys(HEAs)FeCoNiCu_(x)(x=0.5,1.0,1.5,2.0,2.5)were produced by vacuum induction smelting.The effects of Cu content on the microstructure and mechanical properties of the alloys were interrogated by X-ray diffractometer(XRD),field scanning electron microscope(FESEM)and tensile mechanical test.The result shows that the HEAs form single FCC solid solution phase.With the increase of Cu content,the diffraction peak first deviated to the right and then shifted to the left.The alloys changed from equiaxed crystal structure to refined dendritic crystal structure,as Cu content increased.A large number of Cu atoms are isolated in the inter-crystalline region.The tensile mechanical tests show that with the increase of Cu content,the ultimate tensile strength first increased and then decreased.When x is 2.0,the ultimate tensile strength reaches a maximum of 473 MPa,the percent elongation is 43.0%,and the fracture presents ductile behaviour.展开更多
The effects of copper content on the microstructural and mechanical properties of steel foams are investigated. Spherical urea granules, used as a water-leachable space holder, were coated with a mixture of iron, ultr...The effects of copper content on the microstructural and mechanical properties of steel foams are investigated. Spherical urea granules, used as a water-leachable space holder, were coated with a mixture of iron, ultrafine carbon, and different amounts of copper powders. After the mixture was compacted and the space holder was removed by leaching, a sintering process was performed under an atmosphere of thermally dissociated ammonia. Microstructural evaluations of the cell walls were carried out using optical microscopy and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy. In addition, compression tests were conducted to investigate the mechanical properties of the manufactured steel foams. The results showed that the total porosity decreases from 77.2% to 71.9% with increasing copper content in the steel foams. In the foams' microstructure, copper islands are mostly distributed in pearlite and intergranular carbide phases are formed in the grain boundaries. When the copper content was increased from 0 to 4 wt%, the elastic modulus, plateau stress, fracture stress, and fracture strain of manufactured steel foams improved 4.5, 6, 6.4, and 2.5 times, respectively.展开更多
Copper contents(CU) in bodies and serum cerulopasmin(Cp) were assayed in patients with liver cirrhosis(LC) and hepatocarcinoma(HCC) with atomic absorption and other methods.
Copper base alloy was overlaid onto 35CrMnSiA steel plate by tungsten inert gas （TIG） welding method. The heat transfer process was simulated, the microstructures of the copper base overlay were analyzed by scanning...Copper base alloy was overlaid onto 35CrMnSiA steel plate by tungsten inert gas （TIG） welding method. The heat transfer process was simulated, the microstructures of the copper base overlay were analyzed by scanning electron microscopy （SEM） and energy dispersive spectrometer （EDS）, and the friction and abrasion properties of the overlay were measured. The results show that the Fe content increases in the overlay with increasing the welding current. And with the increase of Fe content in the overlay, the friction coefficient increases and the wear mechanism changes from oxidation wear to abrasive wear and plough wear, which is related to the size and quantity of Fe grains in the overlay. While with the increase of Fe content in the overlay, the protection of oxidation layer against the oxidation wear on the melted metal decreases.展开更多
A new method is proposed to prospect copper deposits with portable XRF analyzer. The method is based on the close relation between Cu and the chalcophile elements or some other elements in the geochemical anomalies of...A new method is proposed to prospect copper deposits with portable XRF analyzer. The method is based on the close relation between Cu and the chalcophile elements or some other elements in the geochemical anomalies of a Cu deposit. Applications of the technique in Northeast China are presented.展开更多
By adding copper to increase the performance,the Ni-Ti-Cu Shape Memory Alloy(SMA),has been widely used in the field of engineering in recent years.A thermodynamic constitutive model for Ni-Ti-Cu SMA considering differ...By adding copper to increase the performance,the Ni-Ti-Cu Shape Memory Alloy(SMA),has been widely used in the field of engineering in recent years.A thermodynamic constitutive model for Ni-Ti-Cu SMA considering different copper contents is established in this work.Numerical results for two different copper contents,as examples,are compared with the experimental results to verify the accuracy of the theoretical work.Based on the verified constitutive model,the effects of different copper content on the mechanical properties of Ni-Ti-Cu SMA and the tensile and compressive asymmetric properties of Ni-Ti-Cu SMA are finally discussed,respectively.展开更多
基金supported by C1 Gas Refinery Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Science,ICT & Future Planning (2015M3D3A1A01064908)
文摘Alcohol-assisted low-temperature methanol synthesis was conducted over Cu/ZnO;catalysts while varying the copper content（X）. Unlike conventional methanol synthesis, ethanol acted as both solvent and reaction intermediate in this reaction, creating a different reaction pathway. The formation of crystalline phases and characteristic morphology of the co-precipitated precursors during the co-precipitation step were important factors in obtaining an efficient Cu/ZnO catalyst with a high dispersion of metallic copper,which is one of the main active sites for methanol synthesis. The acidic properties of the Cu/ZnO catalyst were also revealed as important factors, since alcohol esterification is considered the rate-limiting step in alcohol-assisted low-temperature methanol synthesis. As a consequence, bifunctionality of the Cu/ZnO catalyst such as metallic copper and acidic properties was required for this reaction. In this respect, the copper content（X） strongly affected the catalytic activity of the Cu/ZnO;catalysts, and accordingly, the Cu/ZnO;.5 catalyst with a high copper dispersion and sufficient acid sites exhibited the best catalytic performance in this reaction.
基金the National Science Foundation of China under the contract No. 59874005.]
文摘The copper contents and its existing forms in the slags during the slag-making stage of Peirce-Smith converters in Guixi Smelter, Jiangxi Province, China have been investigated. The investigation was based on plant trials with the corresponding thermodynamic calculations and kinetic considerations. From the plant data, the total copper content in the slags was in the range of 2% to 8% (mass fraction). The mechanical entrainment of matte drops has been found to be the main cause of the copper loss. The suspension index, defined as the ratio of the mass fraction of copper in suspended matte drops in the slag to that in bulk of the matte phase, has been adopted to quantify the matte entrainment. The values of this parameter estimated in this work have been found mainly within a range of 2.5%-8.0%. The Fe3O4 content in the slag has been estimated to be the most important factor, among others, influencing the separation of slag with matte and, consequently, the copper loss from the slag.
文摘Metallic hollow spheres are used as base materials in the manufacture of hollow sphere structures and metallic foams. In this study, steel hollow spheres were successfully manufactured using an advanced powder metallurgy technique. The spheres＇ shells were characterized by optical microscopy in conjunction with microstructural image analysis software, scanning electron microscopy（SEM）, energy-dispersive X-ray spectroscopy（EDX）, and X-ray diffraction（XRD）. The microscopic evaluations revealed that the shells consist of sintered iron powder, sintered copper powder, sodium silicate, and porosity regions. In addition, the effects of copper content on various parameters such as shell defects, microcracks, thickness, and porosities were investigated. The results indicated that increasing the copper content results in decreases in the surface fraction of shell porosities and the number of microcracks and an increase in shell thickness.
基金Funded by the National Natural Science Foundation of China(Nos.51371098,51571118)National Undergraduate Training Program for Innovation and Entrepreneurship(No.201910288094Z)。
文摘Five sets of high entropy alloys(HEAs)FeCoNiCu_(x)(x=0.5,1.0,1.5,2.0,2.5)were produced by vacuum induction smelting.The effects of Cu content on the microstructure and mechanical properties of the alloys were interrogated by X-ray diffractometer(XRD),field scanning electron microscope(FESEM)and tensile mechanical test.The result shows that the HEAs form single FCC solid solution phase.With the increase of Cu content,the diffraction peak first deviated to the right and then shifted to the left.The alloys changed from equiaxed crystal structure to refined dendritic crystal structure,as Cu content increased.A large number of Cu atoms are isolated in the inter-crystalline region.The tensile mechanical tests show that with the increase of Cu content,the ultimate tensile strength first increased and then decreased.When x is 2.0,the ultimate tensile strength reaches a maximum of 473 MPa,the percent elongation is 43.0%,and the fracture presents ductile behaviour.
文摘The effects of copper content on the microstructural and mechanical properties of steel foams are investigated. Spherical urea granules, used as a water-leachable space holder, were coated with a mixture of iron, ultrafine carbon, and different amounts of copper powders. After the mixture was compacted and the space holder was removed by leaching, a sintering process was performed under an atmosphere of thermally dissociated ammonia. Microstructural evaluations of the cell walls were carried out using optical microscopy and scanning electron microscopy in conjunction with energy-dispersive X-ray spectroscopy. In addition, compression tests were conducted to investigate the mechanical properties of the manufactured steel foams. The results showed that the total porosity decreases from 77.2% to 71.9% with increasing copper content in the steel foams. In the foams' microstructure, copper islands are mostly distributed in pearlite and intergranular carbide phases are formed in the grain boundaries. When the copper content was increased from 0 to 4 wt%, the elastic modulus, plateau stress, fracture stress, and fracture strain of manufactured steel foams improved 4.5, 6, 6.4, and 2.5 times, respectively.
文摘Copper contents(CU) in bodies and serum cerulopasmin(Cp) were assayed in patients with liver cirrhosis(LC) and hepatocarcinoma(HCC) with atomic absorption and other methods.
文摘Copper base alloy was overlaid onto 35CrMnSiA steel plate by tungsten inert gas （TIG） welding method. The heat transfer process was simulated, the microstructures of the copper base overlay were analyzed by scanning electron microscopy （SEM） and energy dispersive spectrometer （EDS）, and the friction and abrasion properties of the overlay were measured. The results show that the Fe content increases in the overlay with increasing the welding current. And with the increase of Fe content in the overlay, the friction coefficient increases and the wear mechanism changes from oxidation wear to abrasive wear and plough wear, which is related to the size and quantity of Fe grains in the overlay. While with the increase of Fe content in the overlay, the protection of oxidation layer against the oxidation wear on the melted metal decreases.
文摘A new method is proposed to prospect copper deposits with portable XRF analyzer. The method is based on the close relation between Cu and the chalcophile elements or some other elements in the geochemical anomalies of a Cu deposit. Applications of the technique in Northeast China are presented.
基金support by National Natural Science Foundation of China(No.11502284)Key Deployment Projects of the Chinese Academy of Sciences(KFZD-SW-435)the Fundamental Research Funds for the Central Universities of China(3122020077).
文摘By adding copper to increase the performance,the Ni-Ti-Cu Shape Memory Alloy(SMA),has been widely used in the field of engineering in recent years.A thermodynamic constitutive model for Ni-Ti-Cu SMA considering different copper contents is established in this work.Numerical results for two different copper contents,as examples,are compared with the experimental results to verify the accuracy of the theoretical work.Based on the verified constitutive model,the effects of different copper content on the mechanical properties of Ni-Ti-Cu SMA and the tensile and compressive asymmetric properties of Ni-Ti-Cu SMA are finally discussed,respectively.
