Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free em...Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free emulsion polymerization when the conception of particle design and polymer morphology was adopted. Moreover, the influence of mole ratio of BA to MAA, pH value on the oligomer was studied. And the effects of the added amount of oligomer, self-crosslinked monomer and HFBA, mass ratio of BA to MMA, reaction temperature and the initiator on the polymerization technology and the performance of the product, were investigated and optimized. The structure and performance of the fluorocarbon polymer emulsion were characterized and tested with FTIR, TEM, MFT and contact angle and water absorption of the latex film. The experimental results show that the optimal conditions for preparing fluorocarbon polymer emulsion are as follows： for preparing the oligomer, tool ratio of BA to MAA is equal to 1.0 ： 1.60, and pH value is controlled within the range of 8.0 and 9.0; for preparing fluorocarbon polymer emulsion, the added amount of oligmer[P（BA/MANa）] is 6%; mass ratio of BA to MMA is 40 ＂ 60; the added amount of self-crosslinked monomer is 2%, the added amount of HFBA is 15 %; reaction temperature is 80 ℃; the mixture of potassium persulfate and sodium bisulfite is used as the initiator. The film-forming stability of the fluorocarbon polymer emul- sion and the performance of the latex film, which is prepared with the soap-free emulsion polymerization, are better than that prepared with the conventional emulsion polymerization.展开更多
Unlike previous emulsion polymerization, we used grafting reactions in soap-free emulsion systems. In this study, we synthesized grafted PMMA/PEI core-shell nanoparticles by varying the MMA/PEI content and molecular w...Unlike previous emulsion polymerization, we used grafting reactions in soap-free emulsion systems. In this study, we synthesized grafted PMMA/PEI core-shell nanoparticles by varying the MMA/PEI content and molecular weight of PEI (M<sub>n</sub> = 600, 8000, and 10,000). The size and morphology of the core-shell nanoparticles were characterized by a particle size analyzer and scanning electron microscopy. The nanoparticles were 178 - 408 nm in diameter and swelled in water or methanol by 30 - 75 nm. The size of the nanoparticles increased with MMA contents, whereas the size distribution progressively became homogeneous with increasing molecular weight of PEI. Lastly, we measured CO<sub>2</sub> adsorption capacity of the grafted PMMA/PEI core-shell nanoparticles, and we found the capacity to be limited at a level of 0.69 mg, which occurred for nanoparticles prepared from emulsions at a pH value of 11.展开更多
Novel core-shell hydroxyapatite/chitosan biocomposite nanospheres were synthesized in a multiple emulsion. The multiple emulsion was a w/o/w emulsion, made of diammonium phosphate solution as an inner aqueous phase, c...Novel core-shell hydroxyapatite/chitosan biocomposite nanospheres were synthesized in a multiple emulsion. The multiple emulsion was a w/o/w emulsion, made of diammonium phosphate solution as an inner aqueous phase, cyclohexane as an oil phase, and calcium nitrate solution and chitosan solution as an outer aqueous. The forming mechanism of core-shell spheres and the influence of temperature on the morphology of the nanospheres were investigated. The diameter of the resulting core-shell nanospheres was 100-200 nm and the thickness of the chitosan shell was about 10 nm. And it concluded that at different reaction temperature the morphologies of the products would be changed. The core-shell nanospheres have potential applications for the development of new biomedical materials.展开更多
A new kind of inelastomer impact modifier with a coreshell structure was synthesized by employing a multistep composite emulsion polymerization technique, the size and morphology structure of the coreshell particles c...A new kind of inelastomer impact modifier with a coreshell structure was synthesized by employing a multistep composite emulsion polymerization technique, the size and morphology structure of the coreshell particles could be controlled by the multistep composite emulsion polymerization technique. The study of the impact strength and the elongation at break of the PVC/CPE blend with different contents of coreshell particles(CS) indicated that the mechanical properties of PVC/CPE/CS composite were the best when the concentration of the particle was 25%(mass fraction) which showed the different regularities and characteristics of elastomer toughening plastic.展开更多
Silica sol prepared by sol-gel method was introduced into poly (butyl acrylate) (PBA)/poly (butyl acrylate-styrene-methacryloxypropyl trimethoxysilane) (PSBM) core-shell emulsions to prepare a series of paper surface ...Silica sol prepared by sol-gel method was introduced into poly (butyl acrylate) (PBA)/poly (butyl acrylate-styrene-methacryloxypropyl trimethoxysilane) (PSBM) core-shell emulsions to prepare a series of paper surface sizing agents. The rheological measurement indicated that PSBM emulsions exhibited shear-thinning behavior, and the phenomena became more pronounced with increasing silica sol concentration. Dynamic mechanical analysis (DMA) demonstrated that the stronger interfacial interaction between silica sol and polymer matrix, but microphase separation took place with excess silica sol. Thereby the tensile strength and thermal stability of emulsion films were increased with desirable silica sol concentration, and when silica sol concentration was greater than 6 wt%, the tensile strength leveled off and the decomposition temperature decreased from 351.19℃ to 331.63℃. The degree of crystallinity increased from 5.12% to 10.98% with 4% silica sol addition, resulting in enhanced rigidity of films. Furthermore, the interaction between polymer and fiber was improved with certain amount of silica sol, resulting in improved sizing degree, ring crush strength, surface strength and folding strength. However, excessive crosslinking will be harmful for the properties of sized paper.展开更多
In this manuscript, we describe the novel method for preparing the microcapsules containing α-tocopherol oil droplets as the first core material, calcium chloride powder as the second core material and the fine water...In this manuscript, we describe the novel method for preparing the microcapsules containing α-tocopherol oil droplets as the first core material, calcium chloride powder as the second core material and the fine water droplets as the third core material by the interfacial condensation reaction between hydroxyl propyl methyl cellulose and tannic acid. The interfacial condensation reaction was performed between hydroxyl propyl methyl cellulose dissolved in the continuous water phase and tannic acid dissolved in the inner fine water droplets as the third core material. The calcium chloride powder as the second core material was dispersed in the α-tocopherol oil droplet as the first core material beforehand. The α-tocopherol oil containing the second and the third core materials was dispersed in the continuous water phase to form the [(S + W)/O/W] emulsion. The α-tocopherol oil as the first core material was microencapsulated satisfactorily and the contents of the second core material were increased with the concentration of stearic acid as the oil soluble stabilizer. The mechanical strength of microcapsules increased with the concentration of hydroxyl propyl methyl cellulose. Thermal energy could be released by breaking the microcapsules in water and by dissolving calcium chloride in the continuous water phase.展开更多
In this work, we describe a straightforward approach to produce monodisperse Janus and core-shell particles by using organic solvent free single emulsion droplet-based microfluidic device combining with off-chip polym...In this work, we describe a straightforward approach to produce monodisperse Janus and core-shell particles by using organic solvent free single emulsion droplet-based microfluidic device combining with off-chip polymerization. To accomplish this, methyl methacrylate（MMA） was used as both the oil phase and solvent to dissolve a polymerizable PEGbased macromolecular surfactant, instead of traditional surfactant, and the photo-initiator. Janus particles can be easily obtained by off-chip UV polymerization due to polymerization induced phase separation between PEG and the formed poly（methyl methacrylate）. At the same time, core-shell particles can also be easily attained by inverting the original collecting tube several times and then exposing to UV light. These results may extend the scope of microfluidic technology and the studies on polymerization induced self-assembly/phase-separation into easy fabrication of various new functional materials.展开更多
Organo-fly ash （OFA） was prepared with pretreated fly ash （FA） and hexadecyltrimethyl ammonium bromide （HDTMAB）, and the composites composed of OFA and polyaniline were obtained by emulsion polymerization at dif...Organo-fly ash （OFA） was prepared with pretreated fly ash （FA） and hexadecyltrimethyl ammonium bromide （HDTMAB）, and the composites composed of OFA and polyaniline were obtained by emulsion polymerization at different OFA weight ratios （2.0 wt%, 5.0 wt%, 10.0 wt%, 15.0 wt% and 20.0 wt%） in the presence of dodecylbenzenesulfonic acid as dopant and emulsifier. A polymerization procedure was supposed. The electrical conductivities of the composites were tested by the four-probe technique. The chemical structure and crystallinity of the composites were confirmed by FT-IR and X-ray diffraction, respectively. Morphologies of FA, OFA and the composites were observed by SEM. The element analysis was performed by energy dispersive spectrometry. The thermal stability of the composites was analyzed by TGA. The results showed that the electrical conductivity of the composites decreased with increasing the feed weight ratio of OFA, and the lowest value was 0.62 S/cm. HDTMAB and PAn were just adsorbed on the surface of FA and OFA, respectively according to the physical adsorption without destroying the crystalline structure of FA or OFA. The surface became smoother after organification of FA by using HDTMAB, and its content on FA surfaces was about 26.9 wt%. The core/shell structure of the composite was observed by SEM analysis. The composites showed a higher thermal stability than pure PAn by introduction of OFA into this polymerization system, the heat stability of PAn was increased by decreasing 31.8 wt% of weight loss after introducing 20 wt% of OFA.展开更多
基金Funded by the Jiangsu Provincial Creative Fund for Scientific and Tech-nical Small and Medium-size Enterprise
文摘Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free emulsion polymerization when the conception of particle design and polymer morphology was adopted. Moreover, the influence of mole ratio of BA to MAA, pH value on the oligomer was studied. And the effects of the added amount of oligomer, self-crosslinked monomer and HFBA, mass ratio of BA to MMA, reaction temperature and the initiator on the polymerization technology and the performance of the product, were investigated and optimized. The structure and performance of the fluorocarbon polymer emulsion were characterized and tested with FTIR, TEM, MFT and contact angle and water absorption of the latex film. The experimental results show that the optimal conditions for preparing fluorocarbon polymer emulsion are as follows： for preparing the oligomer, tool ratio of BA to MAA is equal to 1.0 ： 1.60, and pH value is controlled within the range of 8.0 and 9.0; for preparing fluorocarbon polymer emulsion, the added amount of oligmer[P（BA/MANa）] is 6%; mass ratio of BA to MMA is 40 ＂ 60; the added amount of self-crosslinked monomer is 2%, the added amount of HFBA is 15 %; reaction temperature is 80 ℃; the mixture of potassium persulfate and sodium bisulfite is used as the initiator. The film-forming stability of the fluorocarbon polymer emul- sion and the performance of the latex film, which is prepared with the soap-free emulsion polymerization, are better than that prepared with the conventional emulsion polymerization.
文摘Unlike previous emulsion polymerization, we used grafting reactions in soap-free emulsion systems. In this study, we synthesized grafted PMMA/PEI core-shell nanoparticles by varying the MMA/PEI content and molecular weight of PEI (M<sub>n</sub> = 600, 8000, and 10,000). The size and morphology of the core-shell nanoparticles were characterized by a particle size analyzer and scanning electron microscopy. The nanoparticles were 178 - 408 nm in diameter and swelled in water or methanol by 30 - 75 nm. The size of the nanoparticles increased with MMA contents, whereas the size distribution progressively became homogeneous with increasing molecular weight of PEI. Lastly, we measured CO<sub>2</sub> adsorption capacity of the grafted PMMA/PEI core-shell nanoparticles, and we found the capacity to be limited at a level of 0.69 mg, which occurred for nanoparticles prepared from emulsions at a pH value of 11.
基金Funded by the National Natural Science Foundation of China(No.50872099)
文摘Novel core-shell hydroxyapatite/chitosan biocomposite nanospheres were synthesized in a multiple emulsion. The multiple emulsion was a w/o/w emulsion, made of diammonium phosphate solution as an inner aqueous phase, cyclohexane as an oil phase, and calcium nitrate solution and chitosan solution as an outer aqueous. The forming mechanism of core-shell spheres and the influence of temperature on the morphology of the nanospheres were investigated. The diameter of the resulting core-shell nanospheres was 100-200 nm and the thickness of the chitosan shell was about 10 nm. And it concluded that at different reaction temperature the morphologies of the products would be changed. The core-shell nanospheres have potential applications for the development of new biomedical materials.
文摘A new kind of inelastomer impact modifier with a coreshell structure was synthesized by employing a multistep composite emulsion polymerization technique, the size and morphology structure of the coreshell particles could be controlled by the multistep composite emulsion polymerization technique. The study of the impact strength and the elongation at break of the PVC/CPE blend with different contents of coreshell particles(CS) indicated that the mechanical properties of PVC/CPE/CS composite were the best when the concentration of the particle was 25%(mass fraction) which showed the different regularities and characteristics of elastomer toughening plastic.
文摘Silica sol prepared by sol-gel method was introduced into poly (butyl acrylate) (PBA)/poly (butyl acrylate-styrene-methacryloxypropyl trimethoxysilane) (PSBM) core-shell emulsions to prepare a series of paper surface sizing agents. The rheological measurement indicated that PSBM emulsions exhibited shear-thinning behavior, and the phenomena became more pronounced with increasing silica sol concentration. Dynamic mechanical analysis (DMA) demonstrated that the stronger interfacial interaction between silica sol and polymer matrix, but microphase separation took place with excess silica sol. Thereby the tensile strength and thermal stability of emulsion films were increased with desirable silica sol concentration, and when silica sol concentration was greater than 6 wt%, the tensile strength leveled off and the decomposition temperature decreased from 351.19℃ to 331.63℃. The degree of crystallinity increased from 5.12% to 10.98% with 4% silica sol addition, resulting in enhanced rigidity of films. Furthermore, the interaction between polymer and fiber was improved with certain amount of silica sol, resulting in improved sizing degree, ring crush strength, surface strength and folding strength. However, excessive crosslinking will be harmful for the properties of sized paper.
文摘In this manuscript, we describe the novel method for preparing the microcapsules containing α-tocopherol oil droplets as the first core material, calcium chloride powder as the second core material and the fine water droplets as the third core material by the interfacial condensation reaction between hydroxyl propyl methyl cellulose and tannic acid. The interfacial condensation reaction was performed between hydroxyl propyl methyl cellulose dissolved in the continuous water phase and tannic acid dissolved in the inner fine water droplets as the third core material. The calcium chloride powder as the second core material was dispersed in the α-tocopherol oil droplet as the first core material beforehand. The α-tocopherol oil containing the second and the third core materials was dispersed in the continuous water phase to form the [(S + W)/O/W] emulsion. The α-tocopherol oil as the first core material was microencapsulated satisfactorily and the contents of the second core material were increased with the concentration of stearic acid as the oil soluble stabilizer. The mechanical strength of microcapsules increased with the concentration of hydroxyl propyl methyl cellulose. Thermal energy could be released by breaking the microcapsules in water and by dissolving calcium chloride in the continuous water phase.
基金financially supported by the National Natural Science Foundation of China(Nos.21274102 and 21304063)the Priority Academic Program Development(PAPD)of Jiangsu Higher Education Institutions
文摘In this work, we describe a straightforward approach to produce monodisperse Janus and core-shell particles by using organic solvent free single emulsion droplet-based microfluidic device combining with off-chip polymerization. To accomplish this, methyl methacrylate（MMA） was used as both the oil phase and solvent to dissolve a polymerizable PEGbased macromolecular surfactant, instead of traditional surfactant, and the photo-initiator. Janus particles can be easily obtained by off-chip UV polymerization due to polymerization induced phase separation between PEG and the formed poly（methyl methacrylate）. At the same time, core-shell particles can also be easily attained by inverting the original collecting tube several times and then exposing to UV light. These results may extend the scope of microfluidic technology and the studies on polymerization induced self-assembly/phase-separation into easy fabrication of various new functional materials.
基金supported by the Shaanxi Provincial Education Department(No.09JK528) and Program of Shaanxi Key Subject
文摘Organo-fly ash （OFA） was prepared with pretreated fly ash （FA） and hexadecyltrimethyl ammonium bromide （HDTMAB）, and the composites composed of OFA and polyaniline were obtained by emulsion polymerization at different OFA weight ratios （2.0 wt%, 5.0 wt%, 10.0 wt%, 15.0 wt% and 20.0 wt%） in the presence of dodecylbenzenesulfonic acid as dopant and emulsifier. A polymerization procedure was supposed. The electrical conductivities of the composites were tested by the four-probe technique. The chemical structure and crystallinity of the composites were confirmed by FT-IR and X-ray diffraction, respectively. Morphologies of FA, OFA and the composites were observed by SEM. The element analysis was performed by energy dispersive spectrometry. The thermal stability of the composites was analyzed by TGA. The results showed that the electrical conductivity of the composites decreased with increasing the feed weight ratio of OFA, and the lowest value was 0.62 S/cm. HDTMAB and PAn were just adsorbed on the surface of FA and OFA, respectively according to the physical adsorption without destroying the crystalline structure of FA or OFA. The surface became smoother after organification of FA by using HDTMAB, and its content on FA surfaces was about 26.9 wt%. The core/shell structure of the composite was observed by SEM analysis. The composites showed a higher thermal stability than pure PAn by introduction of OFA into this polymerization system, the heat stability of PAn was increased by decreasing 31.8 wt% of weight loss after introducing 20 wt% of OFA.
