A novel Ag/ZnO core-shell structure for efficient sterilization synergizing antibiotics and subsequently removing residuals

The massive use of antibiotics has led to the aggravation of bacterial resistance and also brought environmental pollution problems.This poses a great threat to human health.If the dosage of antibiotics is reduced by increasing its bactericidal performance,the emergence of drug resistance is certainly delayed,so that there's not enough time for developing drug resistance during treatment.Therefore,we selected typical representative materials of metal Ag and semiconductor ZnO nano-bactericides to design and synthesize Ag/ZnO hollow core-shell structures(AZ for short).Antibiotics are grafted on the surface of AZ through rational modification to form a composite sterilization system.The research results show that the antibacterial efficiency of the composite system is significantly increased,from the sum(34.7%+22.8%-57.5%)of the antibacterial efficiency of AZ and gentamicin to 80.2%,net synergizes 22.7%,which fully reflects the effect of 1+1>2.Therefore,the dosage of antibiotics can be drastically reduced in this way,which makes both the possibility of bacterial resistance and medical expenses remarkably decrease.Subsequently,residual antibiotics can be degraded under simple illumination using AZ-self as a photocatalyst,which cuts off the path of environmental pollution.In short,such an innovative route has guiding significance for drug resistance.

Exploring the Core-shell Structure of BaTiO3-based Dielectric Ceramics Using Machine Learning Models and Interpretability Analysis

A machine learning(ML)-based random forest(RF)classification model algorithm was employed to investigate the main factors affecting the formation of the core-shell structure of BaTiO_(3)-based ceramics and their interpretability was analyzed by using Shapley additive explanations(SHAP).An F1-score changed from 0.8795 to 0.9310,accuracy from 0.8450 to 0.9070,precision from 0.8714 to 0.9000,recall from 0.8929 to 0.9643,and ROC/AUC value of 0.97±0.03 was achieved by the RF classification with the optimal set of features containing only 5 features,demonstrating the high accuracy of our model and its high robustness.During the interpretability analysis of the model,it was found that the electronegativity,melting point,and sintering temperature of the dopant contribute highly to the formation of the core-shell structure,and based on these characteristics,specific ranges were delineated and twelve elements were finally obtained that met all the requirements,namely Si,Sc,Mn,Fe,Co,Ni,Pd,Er,Tm,Lu,Pa,and Cm.In the process of exploring the structure of the core-shell,the doping elements can be effectively localized to be selected by choosing the range of features.

Engineering hollow core-shell hetero-structure box to induce interfacial charge modulation for promoting bidirectional sulfur conversion in lithium-sulfur batteries

Severe polysulfide shuttling and sluggish sulfur redox kinetics significantly decrease sulfur utilization and cycling stability in lithium-sulfur batteries(LSBs).Herein,we develop a hollow CoO/CoP-Box core-shell heterostructure as a model and multifunctional catalyst modified on separators to induce interfacial charge modulation and expose more active sites for promoting the adsorption and catalytic conversion ability of sulfur species.Theoretical and experimental findings verify that the in-situ formed core-shell hetero-interface induces the formation of P-Co-O binding and charge redistribution to activate surface O active sites for binding lithium polysulfides(LiPSs)via strong Li-O bonding,thus strongly adsorbing with Li PSs.Meanwhile,the strong Li-O bonding weakens the competing Li-S bonding in LiPSs or Li2S adsorbed on CoO/CoP-Box surface,plus the hollow heterostructure provides abundant active sites and fast electron/Li+transfer,so reducing Li2S nucleation/dissolution activation energy.As expected,LSBs with CoO/CoP-Box modified separator and traditional sulfur/carbon black cathode display a large initial capacity of 1240 mA h g^(-1)and a long cycling stability with 300 cycles(~60.1%capacity retention)at 0.5C.Impressively,the thick sulfur cathode(sulfur loading:5.2 mg cm^(-2))displays a high initial areal capacity of 6.9 mA h cm^(-2).This work verifies a deep mechanism understanding and an effective strategy to induce interfacial charge modulation and enhance active sites for designing efficient dual-directional Li-S catalysts via engineering hollow core-shell hetero-structure.

Constructing a hollow core-shell structure of RuO_(2) wrapped by hierarchical porous carbon shell with Ru NPs loading for supercapacitor

Hollow core-shell structure nanomaterials have been broadly used in energy storage, catalysis, reactor,and other fields due to their unique characteristics, including the synergy between different materials,a large specific surface area, small density, large charge carrying capacity and so on. However, their synthesis processes were mostly complicated, and few researches reported one-step encapsulation of different valence states of precious metals in carbon-based materials. Hence, a novel hollow core-shell nanostructure electrode material, RuO_(2)@Ru/HCs, with a lower mass of ruthenium to reduce costs was constructed by one-step hydrothermal method with hard template and co-assembled strategy, consisting of RuO_(2) core and ruthenium nanoparticles(Ru NPs) in carbon shell. The Ru NPs were uniformly assembled in the carbon layer, which not only improved the electronic conductivity but also provided more active centers to enhance the pseudocapacitance. The RuO_(2) core further enhanced the material’s energy storage capacity. Excellent capacitance storage(318.5 F·g^(-1)at 0.5 A·g^(-1)), rate performance(64.4%) from 0.5 A·g^(-1)to 20 A·g^(-1), and cycling stability(92.3% retention after 5000 cycles) were obtained by adjusting Ru loading to 0.92%(mass). It could be attributed to the wider pore size distribution in the micropores which increased the transfer of electrons and protons. The symmetrical supercapacitor device based on RuO_(2)@Ru/HCs could successfully light up the LED lamp. Therefore, our work verified that interfacial modification of RuO_(2) and carbon could bring attractive insights into energy density for nextgeneration supercapacitors.

Fabricating Core-Shell WC@C/Pt Structures and its Enhanced Performance for Methanol Electrooxidation

The spray-dried spheres within a W/Pt multi-separation can be used to prepare discrete core-shell WC@C/Pt catalysts through a typical carburization production mechanism at 800 ℃. In contrast with previous studies of the WC/Pt synthesis, the reaction observed here proceeds through an indirect annealing thereby resulting in core-shell structure, and mechanism at 600℃ wherein species diffuse, Pt nanoparticles were successfully dispersed in size/shape and randomly scattered across the in situ produced C spheres. Through direct carburization or at higher initial hydrochloroplatiuic acid concentrations, however, complete reaction with core-shell spheres was not observed. Indirect carburization reduces the strain felt by the bonds featuring the larger WC WC and Pt nanoparticles to be reserved, stability toward methanol oxidation. particles and allows the motion of carbon around influencing the eleetrocatalytic performance and

Core-shell mesoporous carbon hollow spheres as Se hosts for advanced Al-Se batteries

Incorporating a selenium(Se)positive electrode into aluminum(Al)-ion batteries is an effective strategy for improving the overall battery performance.However,the cycling stability of Se positive electrodes has challenges due to the dissolution of intermediate reaction products.In this work,we aim to harness the advantages of Se while reducing its limitations by preparing a core-shell mesoporous carbon hollow sphere with a titanium nitride(C@TiN)host to load 63.9wt%Se as the positive electrode material for Al-Se batteries.Using the physical and chemical confinement offered by the hollow mesoporous carbon and TiN,the obtained core-shell mesoporous carbon hollow spheres coated with Se(Se@C@TiN)display superior utilization of the active material and remarkable cycling stability.As a result,Al-Se batteries equipped with the as-prepared Se@C@TiN composite positive electrodes show an initial discharge specific capacity of 377 mAh·g^(-1)at a current density of 1000 mA·g^(-1)while maintaining a discharge specific capacity of 86.0 mAh·g^(-1)over 200 cycles.This improved cycling performance is ascribed to the high electrical conductivity of the core-shell mesoporous carbon hollow spheres and the unique three-dimensional hierarchical architecture of Se@C@TiN.

Atomically Dispersed Ruthenium Catalysts with Open Hollow Structure for Lithium-Oxygen Batteries

Lithium–oxygen battery with ultrahigh theoretical energy density is considered a highly competitive next-generation energy storage device,but its practical application is severely hindered by issues such as difficult decomposition of discharge products at present.Here,we have developed N-doped carbon anchored atomically dispersed Ru sites cathode catalyst with open hollow structure(h-RuNC)for Lithium–oxygen battery.On one hand,the abundance of atomically dispersed Ru sites can effectively catalyze the formation and decomposition of discharge products,thereby greatly enhancing the redox kinetics.On the other hand,the open hollow structure not only enhances the mass activity of atomically dispersed Ru sites but also improves the diffusion efficiency of catalytic molecules.Therefore,the excellent activity from atomically dispersed Ru sites and the enhanced diffusion from open hollow structure respectively improve the redox kinetics and cycling stability,ultimately achieving a high-performance lithium–oxygen battery.

Vacancy engineering mediated hollow structured ZnO/ZnS S-scheme heterojunction for highly efficient photocatalytic H_(2) production

Designing a step-scheme(S-scheme)heterojunction photocatalyst with vacancy engineering is a reliable approach to achieve highly efficient photocatalytic H_(2)production activity.Herein,a hollow ZnO/ZnS S-scheme heterojunction with O and Zn vacancies(VO,Zn-ZnO/ZnS)is rationally constructed via ion-exchange and calcination treatments.In such a photocatalytic system,the hollow structure combined with the introduction of dual vacancies endows the adequate light absorption.Moreover,the O and Zn vacancies serve as the trapping sites for photo-induced electrons and holes,respectively,which are beneficial for promoting the photo-induced carrier separation.Meanwhile,the S-scheme charge transfer mechanism can not only improve the separation and transfer efficiencies of photo-induced carrier but also retain the strong redox capacity.As expected,the optimized VO,Zn-ZnO/ZnS heterojunction exhibits a superior photocatalytic H_(2) production rate of 160.91 mmol g^(-1)h^(-1),approximately 643.6 times and 214.5 times with respect to that obtained on pure ZnO and ZnS,respectively.Simultaneously,the experimental results and density functional theory calculations disclose that the photo-induced carrier transfer pathway follows the S-scheme heterojunction mechanism and the introduction of O and Zn vacancies reduces the surface reaction barrier.This work provides an innovative strategy of vacancy engineering in S-scheme heterojunction for solar-to-fuel energy conversion.

Synthesis and Characterization of Fluorine-containing Polyacrylate Emulsion with Core-Shell Structure

A fluorine-containing polyacrylate copolymer emulsion was synthesized by a seed emulsion polymerization method, in which methyl methacrylate （MMA） and butyl acrylate （BA） were used as main monomers and hexafluorobutyl methacrylate （HFMA） as fluorine-containing monomer. The structure and properties were characterized by Fourier transform infrared spectrum （FT-IR）, transmission electron microscopy （TEM）, particle size analysis, X-ray photoelectron spectroscopy （XPS）, contact angle （CA）, differential scanning calorimetry （DSC） and thermogravimetry （TG） analysis. The FTIR and TEM results showed that HFMA was effectively involved in the emulsion copolymerization, and the formed emulsion particles had a core-shell structure and a narrow particle size distribution. XPS and CA analysis revealed that a gradient concentration of fluorine existed in the depth profile of fluorine-containing emulsion film which was richer in fluorine and more hydrophobic in one side. DSC and TG analysis also showed that a clear core-shell structure existed in the fluorine-containing emulsion particles, and their film showed higher thermal stability than that of fluorine-free emulsion.

Synthesis of core-shell nanostructured Cr2O3/C@TiO2 for photocatalytic hydrogen production

In this study,the Cr2O3/C@TiO2 composite was synthesized via the calcination of yolk–shell MIL-101@TiO2.The composite presented core–shell structure,where Cr-doped TiO2 and Cr2O3/C were the shell and core,respectively.The introduction of Cr^3+and Cr2O3/C,which were derived from the calcination of MIL-101,in the composite enhanced its visible light absorbing ability and lowered the recombination rate of the photogenerated electrons and holes.The large surface area of the Cr2O3/C@TiO2 composite provided numerous active sites for the photoreduction reaction.Consequently,the photocatalytic performance of the composite for the production of H2 was better than that of pure TiO2.Under the irradiation of a 300 W Xe arc lamp,the H2 production rate of the Cr2O3/C@TiO2 composite that was calcined at 500°C was 446μmol h−1 g−1,which was approximately four times higher than that of pristine TiO2 nanoparticles.Moreover,the composite exhibited the high H2 production rate of 25.5μmol h−1 g−1 under visible light irradiation(λ>420 nm).The high photocatalytic performance of Cr2O3/C@TiO2 could be attributed to its wide visible light photoresponse range and efficient separation of photogenerated electrons and holes.This paper offers some insights into the design of a novel efficient photocatalyst for water-splitting applications.

Effect of milling process on the core-shell structures and dielectric properties of fine-grained BaTiO_3-based X7R ceramic materials

Fine-grained BaTiO3-based X7R ceramic materials were prepared and the effects of milling process on the core-shell structures and dielectric properties were investigated using scanning electron microscope, transmission electron microscope, and energy dispersive spectroscopy （EDS）. As the milling time extends, the dielectric constant of the ceramics increases, whereas the temperature coefficient of capacitance at 125℃ drops quickly. The changes in dielectric properties are considered relevant to the microstructure evolution caused by the milling process. Defects on the surface of BaTiO3 particles increase because of the effects of milling process, which will make it easier for additives to diffuse into the interior grains. As the milling time increases, the shell region gets thicker and the core region gets smaller; however, EDS results show that the chemical inhomogeneity between grain core and grain shell becomes weaker.

Synthesis of Ag@Al_2O_3 Core-shell Structure Nanoparticles and Their Enhancement Effect on Dielectric Properties for Ag@Al_2O_3/Polyimide Nanocomposites

A novel core-shell structure Ag@Al2O3 nano-particles were synthesized and doped into polyimide as conductive fillers to prepare the composite films with high dielectric properties and low dielectric loss. The morphology and structures of the Ag@Al2O3 nano-particles were characterized by transmission electron microscopy （TEM）, X-ray diffraction （XRD）, and UV-visible spectroscopy. All the results proved that the Ag@Al2O3 nano-parficles had a typical core-shell structure, for the Ag particles were coated by Al2O3 shell and the average sizes ofAg@Al2O3 particles were between 30 to 150 nm. The as-prepared Ag@Al2O3 nanoparticles were doped into the polyimide with different mass fractions to fabricate the Ag@Al2O3/PI composite films via in-situ polymerization process. SEM analysis of composite films showed that the Ag@Al2O3 nano- particles homogeneously dispersed in polyimide matrix with nanoseale. As dielectric materials for electronic packaging systems, the Ag@Al2O3/PI composites exhibited appropriate mechanical properties and erthaneed dielectric properties, including greatly enhanced dielectric constant and just a slight increase in dielectric loss. These improvements were attributed to the core-shell structure of fillers and their fine dispersion in the PI matrix.

Core-shell structured 1,4-benzoquinone@TiO_2 cathode for lithium batteries

Organic carbonyl compounds are considered as promising candidates for lithium batteries due to theirhigh capacity and environmental friendliness, However, they suffer from serious dissolution in the elec-trolyte, leading to fast capacity decay. Here we report core-shell structured 1,4-benzoquinone@titaniumdioxide （BQ@TiO2） composite as cathode for lithium batteries. The composite cathode can deliver a highdischarge capacity of 441.2 mA h/g at 50 mA/g and a high capacity retention of 80.7% after 100 cycles. Thegood cycling performance of BQ@TiO2 composite can be attributed to the suppressed dissolution of BQ,which results from the physical confinement effect of Ti02 shell and the strong interactions between BQand Ti02. Moreover, the combination of ex situ infrared spectra and density functional theory calculationsreveals that the active redox sites of BQ are carbonyl groups. This work provides an alternative way tomitigate the dissolution of small carbonyl compounds and thus enhance their cycling stability.

Shell-driven Fine Structure Transition of Core Materials in Co@Au Core-shell Nanoparticles

Co@Au core shell nanoparticles(NPs) of different shell thicknesses were fabricated by a combination of the displacement process and the reduction-deposition process in a microfluidic reactor. The effect of the shell thickness on the fine structures(local atom arrangement) of core materials was investigated by X-ray Absorption Near Edge Structure(XANES) and Extended X-ray Absorption Fine Structure(EXAFS).The results indicate that the shell thickness affects the fine structure of the core materials by causing atomic re-arrangement between the hexagonal close pack(hcp) and the face centered cubic(fcc) structure, and forming Co-Au bonds in the core-shell interface.

Preparation of Self-crosslinked Fluorocarbon Polymer Emulsion with Core-shell Structure by the Method of Soap-free Emulsion Polymerization

Using methyl methacrylate （MMA）, butyl acrylate（BA） and hexafluorobutyl acrylate（HFBA） as main raw materials, we prepared self-crosslinked fluorocarbon polymer emulsion with core-shell structure via soap-free emulsion polymerization when the conception of particle design and polymer morphology was adopted. Moreover, the influence of mole ratio of BA to MAA, pH value on the oligomer was studied. And the effects of the added amount of oligomer, self-crosslinked monomer and HFBA, mass ratio of BA to MMA, reaction temperature and the initiator on the polymerization technology and the performance of the product, were investigated and optimized. The structure and performance of the fluorocarbon polymer emulsion were characterized and tested with FTIR, TEM, MFT and contact angle and water absorption of the latex film. The experimental results show that the optimal conditions for preparing fluorocarbon polymer emulsion are as follows： for preparing the oligomer, tool ratio of BA to MAA is equal to 1.0 ： 1.60, and pH value is controlled within the range of 8.0 and 9.0; for preparing fluorocarbon polymer emulsion, the added amount of oligmer[P（BA/MANa）] is 6%; mass ratio of BA to MMA is 40 ＂ 60; the added amount of self-crosslinked monomer is 2%, the added amount of HFBA is 15 %; reaction temperature is 80 ℃; the mixture of potassium persulfate and sodium bisulfite is used as the initiator. The film-forming stability of the fluorocarbon polymer emul- sion and the performance of the latex film, which is prepared with the soap-free emulsion polymerization, are better than that prepared with the conventional emulsion polymerization.

Synthesis of carbon-coated cobalt ferrite core-shell structure composite:A method for enhancing electromagnetic wave absorption properties by adjusting impedance matching

Cobalt ferrite has problems such as poor impedance matching and high density,which results in unsatisfactory electromagnetic wave(EMW)absorption performance.In this study,the CoFe_(2)O_(4)@C core-shell structure composite was synthesized by a two-step hydrothermal method.X-ray diffraction,transmission electron microscopy,Fourier transform infrared spectroscopy,thermogravimetric analysis,and vector network analysis et al.were used to test the structure and EMW absorption properties of CoFe_(2)O_(4)@C composite.The results show that the reflection loss(RL)of the CoFe_(2)O_(4)@C composite reaches the maximum value of25.66 dB at 13.92 GHz,and the effective absorbing band(EAB)is 4.59 GHz(11.20-15.79 GHz)when the carbon mass content is 6.01%.The RL and EAB of CoFe_(2)O_(4)@C composite are increased by 219.55%and 4.59 GHz respectively,and the density is decreased by 20.78%compared with the cobalt ferrite.Such enhanced EMW absorption properties of CoFe_(2)O_(4)@C composite are attributed to the attenuation caused by the strong natural resonance of the cobalt ferrite,moreover,the carbon coating layer adjusts the impedance matching of the composite,and the introduced dipole polarization and interface polarization can cause multiple Debye relaxation processes.

Preparation and Properties of Polyurethane/Nickel Nanofiber with Core-Shell Structure Using Coaxial Electrospinning Method

Nanofiber has been widely used in numerous fields for its good advantages such as large surface area and porosity.However,the relationship between nanofiber structure and coaxial electrospinning process is still not clear and deserved to be studied.In this work,a kind of polyurethane/nickel(PU/Ni)nanofiber with core-shell structures was developed,and the effects of electrospinning parameters on the properties of nanofiber were evaluated.The results showed that the optimized parameters of core-shell electrospinning speeds were 1 mL/h(core)and 1 mL/h(shell),respectively.Sample c with the core-shell electrospinning speed ratio of 1∶1,exhibited the relatively smooth surface,good orientation,and bonding points.It also had the largest tensile strength at 99 cN,tensile elongation at 44.86%,and the best electricity conductivity,which showed great potential in the application of nanofiber fields.

Application of Monodisperse Thermo-Responsive Composite Microgels with Core-Shell Structure Based on Au@Ag Bimetallic Nanorod as Core in Surface Enhanced Raman Spectroscopy Substrate

The monodisperse Au@Ag bimetallic nanorod is encapsulated by crosslinked poly( N-isopropylacrylamide)( PNIPAM) to produce thermo-responsive composite microgel with well-defined core-shell structure( Au@ Ag NR@ PNIPAM microgel)by seed-precipitation polymerization method using butenoic acid modified Au @ Ag NRs as seeds. When the temperature of the aqueous medium increases from 20℃ to 50℃,the localized surface plasmon resonance( LSPR) band of the entrapped Au @ Ag NR is pronouncedly red-shifted because of the decreased spatial distances between them as a result of shrinkage of the microgels,leading to their plasmonic coupling. The temperature tunable plasmonic coupling is demonstrated by temperature dependence of the surface enhanced Raman spectroscopy( SERS) signal of 1-naphthol in aqueous solution. Different from static plasmonic coupling modes from nanostructured assembly or array system of noble metals,the proposed plasmonic coupling can be dynamically controlled by environmental temperature. Therefore, the thermo responsive hybrid microgels have potential applications in mobile LSPR or SERS microsensors for living tissues or cells.

Immobilization of metalloporphyrins on CeO_2@SiO_2 with a core-shell structure prepared via microemulsion method for catalytic oxidation of ethylbenzene

Ce O2@Si O2 core-shell nanoparticles were prepared by microemulsion method, and metalloporphyrins were immobilized on the Ce O2@Si O2 core-shell nanoparticles surface via amide bond. The supported metalloporphyrin catalysts were characterized by N2 adsorption-desorption isotherm(BET), scanning electron microscopy(SEM), transmission electron microscopy(TEM), X-ray diffraction(XRD), ultraviolet and visible spectroscopy(UV-Vis), and Fourier transform infrared spectroscopy(FT-IR). The results show that the morphology of Ce O2@Si O2 nanoparticles is core-shell microspheres with about 30 nm in diameter, and metalloporphyrins are immobilized on the Ce O2@Si O2 core-shell nanoparticles via amide bond. Especially, the core-shell structure contains multi Ce O2 core and thin Si O2 shell, which may benefit the synergistic effect between the Ce O2 core and the porphyrin anchored on the very thin Si O2 shell. As a result, this supported metalloporphyrin catalysts present comparably high catalytic activity and stability for oxidation of ethylbenzene with molecular oxygen, namely, ethylbenzene conversion remains around 12% with identical selectivity of about 80% for acetophenone even after six-times reuse of the catalyst.