准确计算户内变电站大型、复杂的噪声场分布,进而评价可采用降噪措施的减噪效果,是解决户内变电站噪声污染的关键问题。为此,综合声学有限元法(finite element method,FEM)求解复杂声场收敛性好及精度高的优点,及声学边界元法(boundary ...准确计算户内变电站大型、复杂的噪声场分布,进而评价可采用降噪措施的减噪效果,是解决户内变电站噪声污染的关键问题。为此,综合声学有限元法(finite element method,FEM)求解复杂声场收敛性好及精度高的优点,及声学边界元法(boundary element method,BEM)降维求解大型声场的优势,提出了一种基于声学FEM-BEM的户内变电站噪声场求解算法。首先,建立变电站内部声源声固耦合模型,采用声学FEM求解混响噪声作用下的声固耦合响应;然后,基于声学FEM-BEM耦合理论,求解内、外耦合边界处结构单元受声固耦合激励产生的位移及应力载荷;最后,根据声压及应力载荷激发的外场声波扩散模型,基于常规Gauss数值积分法,建立外部空间声域2维BEM声学积分方程,求解外部声场。该算法在湖南某110 kV户内变电站噪声场的求解分析中得到了成功应用,与实测值的相对误差为3.61%~4.87%。展开更多
振动污染在国际上已被列入“七大环境公害”之一,填充沟是振动污染治理的一种常用隔振屏障。传统的填充沟受工程造价和施工工艺等限制工程中应用较困难;为克服上述问题,提出一种新型隔振屏障-内插预制芯墙的劲芯水泥土墙。对于饱和地基...振动污染在国际上已被列入“七大环境公害”之一,填充沟是振动污染治理的一种常用隔振屏障。传统的填充沟受工程造价和施工工艺等限制工程中应用较困难;为克服上述问题,提出一种新型隔振屏障-内插预制芯墙的劲芯水泥土墙。对于饱和地基中劲芯水泥土墙的隔振问题,饱和地基采用饱和土半解析边界元法(boundary element method,BEM)建模,劲芯水泥土墙采用有限元法(finite element method,FEM)建模,根据饱和地基-水泥土墙交界面的平衡和连续性条件,分别建立了劲芯水泥土墙对入射Rayleigh波(瑞利波)的远场被动隔振和对动力机器基础振动近场主动隔振的半解析BEM-FEM耦合分析方法,并对劲芯水泥土墙的隔振效果进行了计算分析。研究结果表明:饱和地基中设置劲芯水泥土墙能够起到较好的隔振作用,其隔振效果与混凝土墙基本相当且远优于纯水泥土墙;预制芯墙在劲芯水泥土墙隔振系统中起关键作用,为避免弹性波从芯墙底绕射而降低隔振效果,预制芯墙深度应与水泥土墙深度保持一致;增大芯墙厚度对隔振效果提升不大。在等深芯墙条件下,增大墙深能显著提高远场隔振效果,但对近场隔振效果提升较小;增大墙厚也可提高隔振效果,但提高幅度不大。实际工程中,建议结合工程造价和施工工艺,选择合适的水泥土墙和预制芯墙墙厚。此外,屏障距振源距离对主动隔振效果影响较小,建议根据被保护建筑与振源之间的实际情况,选择合适位置构建隔振屏障。展开更多
To design a propeller for ship power plant,the interaction between ship hull and propeller must be taken into account.The main concern is to apply the wake effect of ship stern on the propeller performance.In this pap...To design a propeller for ship power plant,the interaction between ship hull and propeller must be taken into account.The main concern is to apply the wake effect of ship stern on the propeller performance.In this paper,a coupled BEM(Boundary Element Method)/RANS(Renolds-Averaged Navier−Stokes)solver is used to simulate propeller behind the hull in the self-propulsion test.The motivation of this work is to develop a practical tool to design marine propulsion system without suffering long computational time.An unsteady boundary element method which is also known as panel method is chosen to estimate the propeller forces.Propeller wakes are treated using a time marching wake alignment method.Also,a RANS code coupled with VoF equation is developed to consider the ship motions and wake field effects in the problem.A coupling algorithm is developed to interchange ship wake field to the potential flow solver and propeller thrust to the RANS code.Based on the difference between hull resistance and the propeller thrust,a PI controller is developed to compute the propeller RPM in every time step.Verification of the solver is carried out using the towing tank test report of a 50 m oceanography research vessel.Wake factor and trust deduction coefficient are estimated numerically.Also,the wake rollup pattern of the propeller in open water is compared with the propeller in real wake field.展开更多
A method of coupled BEM-FEM analysis for the elastic spatial structure system is presented. It can be applied to the calculation of the stress and deformation of the large-diamater cylinder structure system and it is ...A method of coupled BEM-FEM analysis for the elastic spatial structure system is presented. It can be applied to the calculation of the stress and deformation of the large-diamater cylinder structure system and it is suitable for symmetric or non-symmetric structures under the distributed or concentrated load. Numerical examples show that the proposed method and computer program BEFEM are quite efficient in the analysis of the large-diameter cylinder structure problems in ocean engineering.展开更多
Four new binuclear Fe(Ⅲ) complexes containing the diboon of isophthallc acid as bridge have been synthesized, namely [Fe2(IPHTA)(L)4](ClO4)4[L denotes 2, 2'-bipyridyl (bpy); 1,10-phenanthroline (phen); 4, 4'-...Four new binuclear Fe(Ⅲ) complexes containing the diboon of isophthallc acid as bridge have been synthesized, namely [Fe2(IPHTA)(L)4](ClO4)4[L denotes 2, 2'-bipyridyl (bpy); 1,10-phenanthroline (phen); 4, 4'-dimethyl-2, 2'-bipyridyl (Me2bpy ) and 5-nitro-1, 10-phenanthroline (NO2-phen), respectively], where IPHTA represents the isophthalate dianion. The complex [Fe2(IPHTA)(phen)4](CIO4)4 was characterized with variable temperature magnetic susceptibility (4-300K). The exchange integral J was found to be 9. 96cm(-1), indicating that weakly ferromagnetic spin-exchange interaction operates between Fe(Ⅲ) and Fe(Ⅲ) ions.展开更多
In this study, the magnetohydrodynamic (MHD) flow through a circular pipe under the influence of a transverse mag- netic field when the outside medium is also electrically conducting is solved numerically by using FEM...In this study, the magnetohydrodynamic (MHD) flow through a circular pipe under the influence of a transverse mag- netic field when the outside medium is also electrically conducting is solved numerically by using FEM-BEM coupling approach. The coupled partial differential equations defined for the interior medium are transformed into homogenous modified Helmholtz equations. For the exterior medium on an infinite region, the Laplace equation is considered for the exterior magnetic field. Unknowns in the equations are also related with the corresponding Dirichlet and Neumann type coupled boundary conditions. Unknown values of the magnetic field on the boundary and for the exterior region are obtained by using BEM, and the unknown velocity and magnetic field inside the pipe are obtained by using SUPG type stabilized FEM. Computations are carried for very high values of magnetic Reynolds numbers Rm1, Reynolds number Re and magnetic pressure Rh of the fluid. The results show that using stabilized method enables us to get stable and accurate numerical approximations consistent with the physical configuration of the problem over rough mesh which also results a cheap computational cost.展开更多
The aim of this paper is to model the steady-state condition of a rotary shaft seal (RSS) system. For this, an iterative thermal-mechanical algorithm was developed based on incremental finite element analyzes. The beh...The aim of this paper is to model the steady-state condition of a rotary shaft seal (RSS) system. For this, an iterative thermal-mechanical algorithm was developed based on incremental finite element analyzes. The behavior of the seal’s rubber material was taken into account by a large-strain viscoelastic, so called generalized Maxwell model, based on Dynamic Mechanical Thermal Analyses (DMTA) and tensile measurements. The pre-loaded garter spring was modelled with a bilinear material model and the shaft was assumed to be linear elastic. The density, coefficient of thermal expansion and the thermal conductance of the materials were taken into consideration during simulation. The friction between the rotary shaft seal and the shaft was simplified and modelled as a constant parameter. The iterative algorithm was evaluated at two different times, right after assembly and 1 h after assembly, so that rubber material’s stress relaxation effects are also incorporated. The results show good correlation with the literature data, which state that the permissible temperature for NBR70 (nitrile butadiene rubber) material contacting with ~80 mm shaft diameter, rotating at 2600/min is 100°C. The results show 107°C and 104°C for the two iterations. The effect of friction induced temperature, changes the width of the contact area between the seal and the shaft, and significantly reduces the contact pressure.展开更多
A 3D rigid-plastic and coupled thermo-mechanical FE model for hot ring rolling(HRR) was developed based on DEFORM 3D software,then coupled heat transferring,material flow and temperature distribution of the ring in HR...A 3D rigid-plastic and coupled thermo-mechanical FE model for hot ring rolling(HRR) was developed based on DEFORM 3D software,then coupled heat transferring,material flow and temperature distribution of the ring in HRR were simulated and the effects of process parameters on them were analyzed.The results show that the deformation nonuniformity of ring blank increases with the increase of the rotational speed of driver roll and friction factor or the decrease of the feed rate of idle roll and initial temperature of ring blank.The temperature nonuniformity of ring blank decreases with the increase of the feed rate of idle roll or the decrease of initial temperature of ring blank and friction factor.There is an optimum rotational speed of driver roll under which the temperature distribution of ring blank is the most uniform.The results obtained can provide a guide for forming parameters optimization and quality control.展开更多
以对称层合板结构为对象,基于经典层合板理论,将其等效为单层各项异性板,采用FE-BEM法(hybrid finite element-boundary element method)分析了其在宽频噪声激励作用下的隔声特性。为验证等效方法的适用性,开展对称复合材料层合板模态...以对称层合板结构为对象,基于经典层合板理论,将其等效为单层各项异性板,采用FE-BEM法(hybrid finite element-boundary element method)分析了其在宽频噪声激励作用下的隔声特性。为验证等效方法的适用性,开展对称复合材料层合板模态测试和数值分析;为验证预估结论的正确性,将FE-BEM法结果与FE-SEA法(hybrid finite element-statistic energy analysis)结果、试验结果分别进行对比。结果表明:将等效方法用于对称层合板固有特性模拟是正确的,等效层合板的固有特性的仿真结果与试验值一致,误差在6.9%以内;等效方法和FE-BEM法结合进行对称层合板隔声预计是有效的,FE-BEM法预计结果与试验结果吻合良好;等效方法和FE-SEA法结合进行对称层合板隔声预计也是有效的,FE-BEM法比FE-SEA法所建模型计算耗时长,算例中计算耗时增大4.4%。展开更多
文摘准确计算户内变电站大型、复杂的噪声场分布,进而评价可采用降噪措施的减噪效果,是解决户内变电站噪声污染的关键问题。为此,综合声学有限元法(finite element method,FEM)求解复杂声场收敛性好及精度高的优点,及声学边界元法(boundary element method,BEM)降维求解大型声场的优势,提出了一种基于声学FEM-BEM的户内变电站噪声场求解算法。首先,建立变电站内部声源声固耦合模型,采用声学FEM求解混响噪声作用下的声固耦合响应;然后,基于声学FEM-BEM耦合理论,求解内、外耦合边界处结构单元受声固耦合激励产生的位移及应力载荷;最后,根据声压及应力载荷激发的外场声波扩散模型,基于常规Gauss数值积分法,建立外部空间声域2维BEM声学积分方程,求解外部声场。该算法在湖南某110 kV户内变电站噪声场的求解分析中得到了成功应用,与实测值的相对误差为3.61%~4.87%。
文摘振动污染在国际上已被列入“七大环境公害”之一,填充沟是振动污染治理的一种常用隔振屏障。传统的填充沟受工程造价和施工工艺等限制工程中应用较困难;为克服上述问题,提出一种新型隔振屏障-内插预制芯墙的劲芯水泥土墙。对于饱和地基中劲芯水泥土墙的隔振问题,饱和地基采用饱和土半解析边界元法(boundary element method,BEM)建模,劲芯水泥土墙采用有限元法(finite element method,FEM)建模,根据饱和地基-水泥土墙交界面的平衡和连续性条件,分别建立了劲芯水泥土墙对入射Rayleigh波(瑞利波)的远场被动隔振和对动力机器基础振动近场主动隔振的半解析BEM-FEM耦合分析方法,并对劲芯水泥土墙的隔振效果进行了计算分析。研究结果表明:饱和地基中设置劲芯水泥土墙能够起到较好的隔振作用,其隔振效果与混凝土墙基本相当且远优于纯水泥土墙;预制芯墙在劲芯水泥土墙隔振系统中起关键作用,为避免弹性波从芯墙底绕射而降低隔振效果,预制芯墙深度应与水泥土墙深度保持一致;增大芯墙厚度对隔振效果提升不大。在等深芯墙条件下,增大墙深能显著提高远场隔振效果,但对近场隔振效果提升较小;增大墙厚也可提高隔振效果,但提高幅度不大。实际工程中,建议结合工程造价和施工工艺,选择合适的水泥土墙和预制芯墙墙厚。此外,屏障距振源距离对主动隔振效果影响较小,建议根据被保护建筑与振源之间的实际情况,选择合适位置构建隔振屏障。
文摘To design a propeller for ship power plant,the interaction between ship hull and propeller must be taken into account.The main concern is to apply the wake effect of ship stern on the propeller performance.In this paper,a coupled BEM(Boundary Element Method)/RANS(Renolds-Averaged Navier−Stokes)solver is used to simulate propeller behind the hull in the self-propulsion test.The motivation of this work is to develop a practical tool to design marine propulsion system without suffering long computational time.An unsteady boundary element method which is also known as panel method is chosen to estimate the propeller forces.Propeller wakes are treated using a time marching wake alignment method.Also,a RANS code coupled with VoF equation is developed to consider the ship motions and wake field effects in the problem.A coupling algorithm is developed to interchange ship wake field to the potential flow solver and propeller thrust to the RANS code.Based on the difference between hull resistance and the propeller thrust,a PI controller is developed to compute the propeller RPM in every time step.Verification of the solver is carried out using the towing tank test report of a 50 m oceanography research vessel.Wake factor and trust deduction coefficient are estimated numerically.Also,the wake rollup pattern of the propeller in open water is compared with the propeller in real wake field.
文摘A method of coupled BEM-FEM analysis for the elastic spatial structure system is presented. It can be applied to the calculation of the stress and deformation of the large-diamater cylinder structure system and it is suitable for symmetric or non-symmetric structures under the distributed or concentrated load. Numerical examples show that the proposed method and computer program BEFEM are quite efficient in the analysis of the large-diameter cylinder structure problems in ocean engineering.
文摘Four new binuclear Fe(Ⅲ) complexes containing the diboon of isophthallc acid as bridge have been synthesized, namely [Fe2(IPHTA)(L)4](ClO4)4[L denotes 2, 2'-bipyridyl (bpy); 1,10-phenanthroline (phen); 4, 4'-dimethyl-2, 2'-bipyridyl (Me2bpy ) and 5-nitro-1, 10-phenanthroline (NO2-phen), respectively], where IPHTA represents the isophthalate dianion. The complex [Fe2(IPHTA)(phen)4](CIO4)4 was characterized with variable temperature magnetic susceptibility (4-300K). The exchange integral J was found to be 9. 96cm(-1), indicating that weakly ferromagnetic spin-exchange interaction operates between Fe(Ⅲ) and Fe(Ⅲ) ions.
文摘In this study, the magnetohydrodynamic (MHD) flow through a circular pipe under the influence of a transverse mag- netic field when the outside medium is also electrically conducting is solved numerically by using FEM-BEM coupling approach. The coupled partial differential equations defined for the interior medium are transformed into homogenous modified Helmholtz equations. For the exterior medium on an infinite region, the Laplace equation is considered for the exterior magnetic field. Unknowns in the equations are also related with the corresponding Dirichlet and Neumann type coupled boundary conditions. Unknown values of the magnetic field on the boundary and for the exterior region are obtained by using BEM, and the unknown velocity and magnetic field inside the pipe are obtained by using SUPG type stabilized FEM. Computations are carried for very high values of magnetic Reynolds numbers Rm1, Reynolds number Re and magnetic pressure Rh of the fluid. The results show that using stabilized method enables us to get stable and accurate numerical approximations consistent with the physical configuration of the problem over rough mesh which also results a cheap computational cost.
文摘The aim of this paper is to model the steady-state condition of a rotary shaft seal (RSS) system. For this, an iterative thermal-mechanical algorithm was developed based on incremental finite element analyzes. The behavior of the seal’s rubber material was taken into account by a large-strain viscoelastic, so called generalized Maxwell model, based on Dynamic Mechanical Thermal Analyses (DMTA) and tensile measurements. The pre-loaded garter spring was modelled with a bilinear material model and the shaft was assumed to be linear elastic. The density, coefficient of thermal expansion and the thermal conductance of the materials were taken into consideration during simulation. The friction between the rotary shaft seal and the shaft was simplified and modelled as a constant parameter. The iterative algorithm was evaluated at two different times, right after assembly and 1 h after assembly, so that rubber material’s stress relaxation effects are also incorporated. The results show good correlation with the literature data, which state that the permissible temperature for NBR70 (nitrile butadiene rubber) material contacting with ~80 mm shaft diameter, rotating at 2600/min is 100°C. The results show 107°C and 104°C for the two iterations. The effect of friction induced temperature, changes the width of the contact area between the seal and the shaft, and significantly reduces the contact pressure.
基金Project(2006AA04Z135) supported by the National Hi-tech Research and Development Program of ChinaProject(50735005) supported by the National Natural Science Foundation of ChinaProject supported by Northwestern Polytechnical University Foundation for Fundamental Research, China
文摘A 3D rigid-plastic and coupled thermo-mechanical FE model for hot ring rolling(HRR) was developed based on DEFORM 3D software,then coupled heat transferring,material flow and temperature distribution of the ring in HRR were simulated and the effects of process parameters on them were analyzed.The results show that the deformation nonuniformity of ring blank increases with the increase of the rotational speed of driver roll and friction factor or the decrease of the feed rate of idle roll and initial temperature of ring blank.The temperature nonuniformity of ring blank decreases with the increase of the feed rate of idle roll or the decrease of initial temperature of ring blank and friction factor.There is an optimum rotational speed of driver roll under which the temperature distribution of ring blank is the most uniform.The results obtained can provide a guide for forming parameters optimization and quality control.
文摘以对称层合板结构为对象,基于经典层合板理论,将其等效为单层各项异性板,采用FE-BEM法(hybrid finite element-boundary element method)分析了其在宽频噪声激励作用下的隔声特性。为验证等效方法的适用性,开展对称复合材料层合板模态测试和数值分析;为验证预估结论的正确性,将FE-BEM法结果与FE-SEA法(hybrid finite element-statistic energy analysis)结果、试验结果分别进行对比。结果表明:将等效方法用于对称层合板固有特性模拟是正确的,等效层合板的固有特性的仿真结果与试验值一致,误差在6.9%以内;等效方法和FE-BEM法结合进行对称层合板隔声预计是有效的,FE-BEM法预计结果与试验结果吻合良好;等效方法和FE-SEA法结合进行对称层合板隔声预计也是有效的,FE-BEM法比FE-SEA法所建模型计算耗时长,算例中计算耗时增大4.4%。
