COUPLED THERMO MECHANICAL FEM ANALYSIS OF TWIST COMPRESSION DEFORMATION PROCESS

3-D rigid-viscoplastic FEM of compressible materials was applied to analyze the deformation behavior during twist compression forming of axisymmetrical body at high temperatures. When calculating the temperature fields, considering the thermo mechanical coupling effect between temperature and deformation, 2-D FEM and CNG methods were adopted, and the up winding technique was used to avoid the influences of numerical instability on calculated results.

2D FEM analysis for coupled thermo-hydro-mechanical-migratory processes in near field of hypothetical nuclear waste repository

In order to consider the influence of temperature and underground water movement, an elastoplastic model and a 2D FEM stress fields on the migration of radioactive nuclide with code for analysis of coupled thermo-hydro-mechanical （THM） processes in saturated and unsaturated porous media were extended and improved through introducing the percolation and migration equation, so that the code can be used for solving the temperature field, flow field, stress field and nuclide concentration field simultaneously. The states of temperatures, pore pressures and nuclide concentrations in the near field of a hypothetical nuclear waste repository were investigated. The influence of the half life of the radioactive nuclide on the temporal change of nuclide concentration was analyzed considering the thermo-hydro-mechanical-migratory coupling. The results show that, at the boundary of the vitrified waste, the concentration of radioactive nuclide with a half life of 10 a falls after a period of rising, with the maximum value of 0.182 mol/m3 and the minimum value of 0.181 mol/m^3 at the end of computation. For a half life of 1 000 a, the concentration of radioactive nuclide always increases with the increase of the time during the computation period; and the maximum value is 1.686 mol/m^3 at the end of the computation. Therefore, under the condition of THM coupling, the concentration of radioactive nuclide with a shorter half life will decrease more quickly with water flow; but for the radioactive nuclide with a longer half life, its concentration will keep at a higher level for a longer time in the migration process.

Coupled BEM-FEM Analysis of the Large-Diameter Cylinder Structure System

A method of coupled BEM-FEM analysis for the elastic spatial structure system is presented. It can be applied to the calculation of the stress and deformation of the large-diamater cylinder structure system and it is suitable for symmetric or non-symmetric structures under the distributed or concentrated load. Numerical examples show that the proposed method and computer program BEFEM are quite efficient in the analysis of the large-diameter cylinder structure problems in ocean engineering.

MPS-FEM Coupled Method for Study of Wave-Structure Interaction

Nowadays,an increasing number of ships and marine structures are manufactured and inevitably operated in rough sea.As a result,some phenomena related to the violent fluid-elastic structure interactions(e.g.,hydrodynamic slamming on marine vessels,tsunami impact on onshore structures,and sloshing in liquid containers)have aroused huge challenges to ocean engineering fields.In this paper,the moving particle semi-implicit(MPS)method and finite element method(FEM)coupled method is proposed for use in numerical investigations of the interaction between a regular wave and a horizontal suspended structure.The fluid domain calculated by the MPS method is dispersed into fluid particles,and the structure domain solved by the FEM method is dispersed into beam elements.The generation of the 2D regular wave is firstly conducted,and convergence verification is performed to determine appropriate particle spacing for the simulation.Next,the regular wave interacting with a rigid structure is initially performed and verified through the comparison with the laboratory experiments.By verification,the MPS-FEM coupled method can be applied to fluid-structure interaction(FSI)problems with waves.On this basis,taking the flexibility of structure into consideration,the elastic dynamic response of the structure subjected to the wave slamming is investigated,including the evolutions of the free surface,the variation of the wave impact pressures,the velocity distribution,and the structural deformation response.By comparison with the rigid case,the effects of the structural flexibility on wave-elastic structure interaction can be obtained.

TRANSIENT FEM FOR AXISYMMETRIC COUPLED THER-MOELASTICITY

Axisymmetric coupled thermoelasticity is investigated by finite element method,and the inertia effect is also considered.A quasi-thermal conduction equation is obtained through transformation.A numerical algorithm is proposed based on the Newmark technology.The effect of inertia and coupling is investigated.

Coupled Thermo-Mechanical Modeling of Long Cone-Shaped Forging Based on Rigid Visco-Plastic FEM

Based on synthetically considering the coupled thermo mechanical relations between temperature and deforming, a numerical simulation of the forging process for the special long cone shaped workpiece of Al 5.44Mg 2.15Li 0.12Zr alloy at high temperature was conducted by using the rigid visco plastic finite element method. The relations between the total load and the displacement during the forging, and the distributions of stress, strain, temperature and strain rate, which can provide useful information for the process design, are obtained.

基于声学FEM-BEM的户内变电站噪声场计算

准确计算户内变电站大型、复杂的噪声场分布,进而评价可采用降噪措施的减噪效果,是解决户内变电站噪声污染的关键问题。为此,综合声学有限元法(finite element method,FEM)求解复杂声场收敛性好及精度高的优点,及声学边界元法(boundary element method,BEM)降维求解大型声场的优势,提出了一种基于声学FEM-BEM的户内变电站噪声场求解算法。首先,建立变电站内部声源声固耦合模型,采用声学FEM求解混响噪声作用下的声固耦合响应;然后,基于声学FEM-BEM耦合理论,求解内、外耦合边界处结构单元受声固耦合激励产生的位移及应力载荷;最后,根据声压及应力载荷激发的外场声波扩散模型,基于常规Gauss数值积分法,建立外部空间声域2维BEM声学积分方程,求解外部声场。该算法在湖南某110 kV户内变电站噪声场的求解分析中得到了成功应用,与实测值的相对误差为3.61%~4.87%。

基于DEM-FEM耦合方法的碎屑流对桥墩最大冲击力的影响因素研究

碎屑流是我国山区最危险的地质灾害之一,山区桥墩常受到碎屑流冲击而开裂、倾斜甚至倒塌,给山区桥梁建设、运营带来严重的安全隐患。采用离散元方法(discrete element method,DEM)和有限元方法(finite element method,FEM)耦合的三维数值模拟方法模拟了碎屑流对双柱式桥墩的冲击效应,并结合斜槽试验,验证了耦合方法的准确性,进一步分析了碎屑流冲击坡度、距离和体积密度对桥墩冲击力的影响规律。结果表明,最大冲击力与碎屑流冲击坡度、距离和体积密度分别呈幂函数(指数大于1)、幂函数(指数小于1)和线性正相关。冲击坡度、距离和体积密度对最大冲击力的敏感度值分别为3.012、0.202、0.804,在桥梁碎屑流灾害防治时需重视冲击坡度和体积密度的影响。将冲击力的数值模拟值与流体动力学模型预测值对比分析表明,流体动力学模型理论公式能较好地预测桥墩所受的最大冲击力,最大预测误差低于23.6%。相关研究结果可为山区桥梁碎屑流灾害防治与设计提供一定的参考依据。

考虑强度速率衰减效应的地震滑坡SPH-FEM模拟

基于SPH和FEM耦合的数值计算方法,引入滑动面摩擦强度的速率衰减模型,提出了一种能够模拟地震诱发滑坡破坏过程的数值模拟方法。基于所提数值方法模拟了唐家山地震滑坡,模拟结果与现场勘查结果及室内试验现象较为一致。基于模拟的滑动面上摩擦系数的演化过程,将唐家山滑坡的发生分为4个阶段:启动阶段、摩擦衰减阶段、低摩擦滑移阶段和逐步稳定阶段。模拟结果表明速度增加和摩擦强度衰减的相互促进,是触发滑体的高速运动的根本原因。提出采用滑体上作用的动摩擦力fd和动下滑力Td的比值R作为判别指标用于判断大型滑坡的启动,当首次出现R小于1时认为滑动面发生整体贯通并出现失稳启动。基于滑动面不同位置摩擦系数的演化,揭示了滑坡启动中滑动面摩擦强度衰减和滑动面的渐进贯通过程,解释了地震作用与滑动面摩擦参数速率衰减效应共同作用触发大型滑坡发生破坏的内在机理。

基于DEM-FEM耦合的环锤式破碎机反击板可靠性分析

由于环锤式破碎机破碎物料的过程是一个极其复杂多变的过程,且与反击板所受的碰撞力是不连续、无规则的,因此,无法使用公式推导或使用单一软件对反击板受力进行计算,为了能够更好地确定破碎机破碎过程中反击板的载荷大小、分布和寿命,文中提出了一种基于离散元(DEM)和有限元(FEM)耦合计算的环锤式破碎机反击板可靠性分析方法,通过EDEM建立环锤式破碎机破碎物料仿真过程,并提取出破碎过程中反击板的载荷分布,与ANSYS Workbench建立耦合计算通道,计算得到在正常工作参数下反击板的受力大小和位置,在此基础上采用n Code Design Life疲劳分析软件对反击板进行寿命分析,得到反击板的受力云图和损伤云图,研究转子转速、反击板倾角、转子与筛板距离等不同因素下对反击板可靠性的影响,结果表明:转子转速为1000 r∕min时反击板的最大受力值为247.9 MPa、反击板角度为60°时应力最大值为206.48 MPa、转子与筛板距离为530 mm时受力最大值为268.37 MPa。

基于SPH-FEM耦合算法的台阶精准爆破延期时间研究及应用

电子雷管在大型露天矿爆破中广泛使用,利用其精准起爆特性通过设置合理延期时间可有效改善爆破质量,对矿山生产降本增效具有重要意义。基于光滑粒子流体动力学—有限单元(SPH-FEM)耦合算法,利用LS-Dyna软件建立了多个巴润矿常规台阶尺寸的三维数值模型。针对电子雷管起爆条件下不同孔间和排间延时分别建立双孔、三孔SPH-FEM三维模型,从矿岩体SPH粒子应力和移动2个维度研究了被爆矿岩体的受力破碎、抛掷位移特征,并重点分析了不同排间延时下后排炮孔爆破漏斗的偏移角度。据此确定了最佳孔间、排间延期时间范围,并通过现场验证对比试验,选出了适合该爆区的最优延时。研究结果表明:在巴润矿现行孔排距条件下利用电子雷管精准起爆,孔间延时在20~30 ms内可达到较好的破碎效果;排间延时大于35 ms时,先爆炮孔为后续炮孔提供新的自由面和抛掷空间,且大于40 ms时应力趋于稳定;在现场验证试验中,试验区内边长1 m以下的破碎矿岩体占比达91%,较非试验爆区中同尺寸岩块占比提高了14%,破碎效果得到有效改善。

基于SPH-FEM耦合方法的泥石流冲击输电塔基础的动力分析

泥石流是我国西南山区常见的地质灾害。架空输电杆塔在泥石流的冲击下往往发生基础破坏甚至会造成杆塔倒塌。首先采用光滑粒子流体动力学(smoothed particle hydrodynamics,简称SPH)方法和有限元方法(finite element method,简称FEM)相耦合的三维数值方法模拟了泥石流对杆塔基础的冲击作用;在与相关模型试验结果验证的基础上,开展了不同泥石流密度、黏度系数及初始速度条件下对输电塔基础的冲击力作用的参数分析;研究结果表明:随着泥石流初始速度的增加,冲击力峰值会随之增大;前排基础的冲击力峰值均大于后排基础;泥石流冲击过程特性受到泥石流密度和黏度系数影响。与稀性泥石流相比:黏性泥石流冲击基础后,基础下游真空区相对要小;此外,将数值模拟结果与Kwan冲击力公式及铁二院推荐的冲击压力设计公式预测值进行对比分析可以发现:Kwan冲击力公式能较好地预测出基础所受泥石流冲击力的平均趋势,最大预测误差低于30%,铁二院公式预测的稀性和黏性泥石流的冲击压力平均偏低分别约17%和28%。相关研究结果有望为泥石流频发区域输电塔基础的设计和风险评估提供一定的参考依据。

基于自适应FEM-SPH耦合算法的飞机典型部位破片冲击战伤的数值研究

针对飞机典型部位在遭到高速破片攻击后结构整体的战伤状态及破片的剩余行为开展数值模拟。应用LS-DYNA软件,结合有限单元方法(finite element method,FEM)和光滑粒子流体动力学(smoothed particle hydrodynamics,SPH)两者的优势,建立自适应的FEM-SPH耦合模拟方法,并构建2种飞机典型部位的计算模型,采用六面体网格局部细化方法实现了核心位置的精确模拟,并进行试验来验证数值模型;开展了一系列高速冲击战伤模拟,对比了不同工况下破片高速冲击结构后形成的碎片云和破口形貌,并对破片的剩余速度和质量进行分析,确定了破片在结构蒙皮上的临界跳飞角。结果表明:自适应FEM-SPH耦合算法的计算结果与试验结果吻合良好,能够对破片高速冲击战伤进行有效准确模拟;碎片云分布形状随破片速度增加变得狭长,冲击角度会改变碎片云和结构破口形状朝向;碎片云高度和扩散速度随破片速度或角度的变化趋势基本一致并都呈线性关系;破片的速度减少量不随初始速度变化,质量减少量则与冲击速度正相关,两者与冲击角度都负相关;破片临界跳飞角与冲击速度大小基本呈线性关系。

基于DEM-FEM耦合模型的质量流量对喷丸强化效果的影响

目的提出一种将有限元(FEM)与离散元(DEM)相耦合的新方法,即通过定义关键字的方式在ABAQUS软件内实现DEM-FEM耦合功能,并应用此方法建立喷丸强化模型。方法将弹丸视为等直径刚体,利用刚体动力学模拟弹丸-弹丸和弹丸-靶材之间相互作用以及整个弹丸流。通过建立的DEM-FEM耦合喷丸强化模型研究质量流量对残余应力场和表面粗糙度的影响。结果质量流量对喷丸强化效果有显著影响,最大残余应力随质量流量的增加而减小,由2 kg/min时的–596.77 MPa下降到6 kg/min时的–581.91 MPa;表面残余应力随质量流量的增加先增大后减小,由2 kg/min时的–420.86 MPa增大到4 kg/min时的472.06 MPa,随后减小到6 kg/min时的–450.50 MPa;表面粗糙度Ra随质量流量的增加减小,由2 kg/min时的11.21μm减小到6 kg/min时的9.82μm。设计了喷丸强化实验,对质量流量2 kg/min的结果进行了验证。结论实测值与模拟值吻合较好,所建立的模型可以准确反映实际喷丸强化过程。质量流量对喷丸强化效果具有显著影响。

饱和地基中劲芯水泥土墙隔振的二维BEM-FEM耦合分析

振动污染在国际上已被列入“七大环境公害”之一,填充沟是振动污染治理的一种常用隔振屏障。传统的填充沟受工程造价和施工工艺等限制工程中应用较困难;为克服上述问题,提出一种新型隔振屏障-内插预制芯墙的劲芯水泥土墙。对于饱和地基中劲芯水泥土墙的隔振问题,饱和地基采用饱和土半解析边界元法(boundary element method,BEM)建模,劲芯水泥土墙采用有限元法(finite element method,FEM)建模,根据饱和地基-水泥土墙交界面的平衡和连续性条件,分别建立了劲芯水泥土墙对入射Rayleigh波(瑞利波)的远场被动隔振和对动力机器基础振动近场主动隔振的半解析BEM-FEM耦合分析方法,并对劲芯水泥土墙的隔振效果进行了计算分析。研究结果表明:饱和地基中设置劲芯水泥土墙能够起到较好的隔振作用,其隔振效果与混凝土墙基本相当且远优于纯水泥土墙;预制芯墙在劲芯水泥土墙隔振系统中起关键作用,为避免弹性波从芯墙底绕射而降低隔振效果,预制芯墙深度应与水泥土墙深度保持一致;增大芯墙厚度对隔振效果提升不大。在等深芯墙条件下,增大墙深能显著提高远场隔振效果,但对近场隔振效果提升较小;增大墙厚也可提高隔振效果,但提高幅度不大。实际工程中,建议结合工程造价和施工工艺,选择合适的水泥土墙和预制芯墙墙厚。此外,屏障距振源距离对主动隔振效果影响较小,建议根据被保护建筑与振源之间的实际情况,选择合适位置构建隔振屏障。

基于PD-FEM混合模型的材料热力耦合损伤分析

提出了一种新的近场动力学-有限元方法(peridynamics-finite element method,PD-FEM)混合模型.该模型用于求解材料热力耦合损伤问题,将求解域划分为近场动力学(PD)区域和有限元方法(FEM)区域,通过FEM节点与PD物质点构成的混合键连接各个子区域.采用该模型对氧化铝陶瓷板在热冲击载荷作用下的损伤行为进行了模拟分析,计算结果表明,采用该混合模型获得的裂纹萌生及扩展与实验研究结果吻合良好,验证了该模型的正确性.该PD-FEM混合模型继承了PD处理不连续问题的优势,同时,由于FEM的引入,大大提高了PD方法在研究材料热力耦合损伤问题时的求解效率.

基于SPH-FEM耦合算法及模型试验的减振棚洞研究

为探究更为安全、有效的边坡落石防护结构,本研究基于光滑粒子流体动力学—有限元(SPH-FEM)耦合动力学数值计算及1∶10几何相似室内模型试验,针对“砂土-发泡橡胶”复合垫层棚洞的减振机制展开研究。结果表明:落石以20 m/s速度冲击时,顶板腹部正中单元峰值应力可达2.89 MPa,超过C30砼极限抗拉强度2.01 MPa;添加0.2、0.4、0.6、0.8、1.0 m发泡橡胶垫层后,正中单元峰值应力依次为2.36、1.12、0.79、0.65、0.58 MPa,相较于纯砂土垫层,降幅依次可达18.34%、61.25%、72.66%、77.51%、79.93%;针对试验期间棚洞顶板腹部纵向测点P1,添加2、4、6 cm厚橡胶垫层,其峰值应变由50.57με依次降至27.17、15.22、10.36με,降幅为46.27%、69.90%、79.51%;针对顶板腹部横向测试位置T1,复合垫层工况下应变峰值由48.47με降至26.54、17.29、13.59με;复合垫层可大幅降低落石冲击能量与顶板应力水平,模型试验与数值计算结果基本相吻合,本文工况下发泡橡胶现场设置厚度以0.4~0.6 m为宜。研究成果可为相关防护工程设计提供借鉴与参考。

基于SPH-FEM算法的森林灭火弹爆炸抛撒灭火剂初速的数模拟研究

针对森林灭火弹爆炸抛撒问题,应用LS-DYNA软件对森林灭火弹爆炸抛撒灭火剂初速进行数值模拟研究。依据森林灭火弹爆炸抛撒实验的数据,对Gurney公式进行修正;建立森林灭火弹的仿真模型,将仿真模型所得灭火剂初速与修正后Gurney公式所得灭火剂初速进行对比,验证SPH-FEM耦合算法研究此类问题的可行性;对森林灭火弹装药结构进行优化,分析阶梯装药结构对灭火剂初速的影响。结果表明,修正后Gurney公式能够更好地适用于灭火剂初速的计算;采用SPH-FEM耦合算法模拟所得灭火剂初速与修正后Gurney公式所得灭火剂初速的吻合度高,表明采用SPH-FEM耦合算法研究此类问题是可行的;对森林灭火弹装药结构进行阶梯化改进可以增大灭火剂抛撒面积与提升灭火剂抛撒均匀性,提高森林灭火弹灭火效率。

FEM COUPLING FIELD ITERATION AND ITS CONVERGENCE FOR A GMM ACTURATOR

The coupling iteration (CI) of the finite element method(FEM) is used to simulate the magnetic and mechanical characteristics for a GMM actuator. The convergent ability under different prestress and different load types is investigated. Then the calculated deformations are compared with the experimental values. The results convince that the CI of FEM is suitable for the simulation of energy coupling and transformation mechanism of the GMM. At last, the output deformation properties are studied under different input currents, showing that there is a good compromise between good linearity and large strain under the prestress 6 MPa.

THE NUMERICAL ANALYSIS OF UNSTEADY HEAT TRANSFER OF A PISTON-LINER COUPLED SYSTEM IN AN INTERNAL COMBUSTION ENGINE

This paper provides a numerical analysis model of unsteady heat trans-fer in piston-liner set of an internal combustion engine.The model simulates the un-steady heat transfer process among the combustion mixture,piston set,lubricantfilm,liner and coolant in a whole engine cycle,and can predict the temperature fluc-tuation and distribution on piston crown,inner surface of liner,piston ring and thelubricant film.A computer program is developed to calculate the unsteady heat trans-fer process of piston-liner system in a water-cooled diesel engine.