The unknown γ-ray excess in the northwest region of Arp 220 was revisited by analyzing~11.8 years of the Fermi Large Area Telescope(Fermi-LAT) data in this study.We found that its photon flux was approximately three ...The unknown γ-ray excess in the northwest region of Arp 220 was revisited by analyzing~11.8 years of the Fermi Large Area Telescope(Fermi-LAT) data in this study.We found that its photon flux was approximately three times higher than that of the previous study in the 0.2-100 GeV band,and the corresponding significance level ~8.15σ was approximately four times higher than before.The light curves of 15 and 45 time bins from the whole time all showed two active periods,and the variability of the second period was more significant than that of the first period.The spectral indices from the two active periods were not statistically different and were close to the range of γ-ray flat-spectrum radio quasars observed by Fermi-LAT.Because the position of CRATES J153246+234400 was consistent with the best-fit position of our analysis,we suggest that CRATES J153246+234400 is more likely a γ-ray counterpart for the variational region.For Arp 220,there was no significant variability in the γ-ray emission.展开更多
The La0.8Sr0.04Ca0.16Co0.6Fe0.4O3-δ (LSCCoF) and La0.9Sr0.1Ga0.8Mg0.2O3 (LSGM) powders were synthesized by glycine-nitrate combustion process and conventional solid-state reaction method, respectively. The LSCCoF-LSG...The La0.8Sr0.04Ca0.16Co0.6Fe0.4O3-δ (LSCCoF) and La0.9Sr0.1Ga0.8Mg0.2O3 (LSGM) powders were synthesized by glycine-nitrate combustion process and conventional solid-state reaction method, respectively. The LSCCoF-LSGM composite cathode material was successfully elaborated and deposited on dense pellets of the LSGM electrolyte by means of slurry spin-coating process. The cathode films with the best surface morphology and microstructure were obtained when the operating parameters fixed as follows: the content of ethyl cellulose which acted as pore former and binder is 10 wt.%, the content of terpineol which acted as modifier is 5 wt.%, the speed of rotation rate is 3200 r/min and the best post-deposition sintering temperature is 1000°C.展开更多
基金the support for this work from the National Key R&D Program of China under Grant No.2018YFA0404204the National Natural Science Foundation of China(NSFC U1931113 and U1738211)+1 种基金the Foundations of Yunnan Province(2018IC059 and 2018FY001(-003))the scientific research fund of Yunnan Education Department(2020Y0039)。
文摘The unknown γ-ray excess in the northwest region of Arp 220 was revisited by analyzing~11.8 years of the Fermi Large Area Telescope(Fermi-LAT) data in this study.We found that its photon flux was approximately three times higher than that of the previous study in the 0.2-100 GeV band,and the corresponding significance level ~8.15σ was approximately four times higher than before.The light curves of 15 and 45 time bins from the whole time all showed two active periods,and the variability of the second period was more significant than that of the first period.The spectral indices from the two active periods were not statistically different and were close to the range of γ-ray flat-spectrum radio quasars observed by Fermi-LAT.Because the position of CRATES J153246+234400 was consistent with the best-fit position of our analysis,we suggest that CRATES J153246+234400 is more likely a γ-ray counterpart for the variational region.For Arp 220,there was no significant variability in the γ-ray emission.
基金Project supported by the Natural Science Foundation of Yunnan Province (2009ZC027M)Program for New Century Excellent Talents in University (NCET-07-0387)
文摘The La0.8Sr0.04Ca0.16Co0.6Fe0.4O3-δ (LSCCoF) and La0.9Sr0.1Ga0.8Mg0.2O3 (LSGM) powders were synthesized by glycine-nitrate combustion process and conventional solid-state reaction method, respectively. The LSCCoF-LSGM composite cathode material was successfully elaborated and deposited on dense pellets of the LSGM electrolyte by means of slurry spin-coating process. The cathode films with the best surface morphology and microstructure were obtained when the operating parameters fixed as follows: the content of ethyl cellulose which acted as pore former and binder is 10 wt.%, the content of terpineol which acted as modifier is 5 wt.%, the speed of rotation rate is 3200 r/min and the best post-deposition sintering temperature is 1000°C.
