Instantaneous creep in face-centered cubic metals, 5N Al（99.999%）, 2N Al （99%） and 4N Cu （99.99%） with different grain sizes, was firstly investigated by sudden stress-change experiments at ultra- low strain rat...Instantaneous creep in face-centered cubic metals, 5N Al（99.999%）, 2N Al （99%） and 4N Cu （99.99%） with different grain sizes, was firstly investigated by sudden stress-change experiments at ultra- low strain rates ε ≤10-10 s-1 and temperature T 〈 0.32 Tn. The experimental results indicate that the observed instantaneous creep is strongly dependent on grain size, the concentration of impurity, and stacking fault energy. Creep in high-purity aluminum, 5N Al, with a very large grain size, d 〉 1600μm, shows non-viscous behavior, and is controlled by the recovery of dislocations in the boundary of dislocation cells. On the other hand, for 5N A1 with a small grain size, d=30μm, and low-purity aluminum, 2N A1, with d8= 25μm, creep shows viscous behavior and may be related to ＇low temperature grain boundary sliding＇. For high-purity copper, 4N Cu, with d= 40 grn and lower stacking fault energy, creep shows a non-viscous behavior, and is controlled by the recovery process of dislocations. For all of the samples, creep shows anelastic behavior.展开更多
The strain rate sensitivity to creep of single crystal Cu（110）, metal tantalum, and 128°Y-X LiNbO3 piezoelectric single crystal were measured at room temperature by MTS Nanoindenter XP. Among the three kinds of...The strain rate sensitivity to creep of single crystal Cu（110）, metal tantalum, and 128°Y-X LiNbO3 piezoelectric single crystal were measured at room temperature by MTS Nanoindenter XP. Among the three kinds of materials studied, Cu showed the highest degree of resistance to creep-induced deformation, which is followed by Ta, while the LiNbO3 single crystal deformed more readily than the others. The values of the steady-state strain rate sensitivities determined by the indentation methods are in the range of 0.002-0.006, 0.02-0.06 and 0.02-0.03 for Cu, Ta, and LiNbO3, respectively. The mechanisms for the indentation-induced creeping behavior and the factors that influenced the creeping are discussed.展开更多
In the present study, creep properties of as-cast Mg-5Al-5Ca-2Sn(AXT552) alloy were investigated by means of a GWT304 creep testing machine at temperatures of 175 °C and 200 °C in the stress range of 35-90 M...In the present study, creep properties of as-cast Mg-5Al-5Ca-2Sn(AXT552) alloy were investigated by means of a GWT304 creep testing machine at temperatures of 175 °C and 200 °C in the stress range of 35-90 MPa. Results show that creep rates increase with applied stress at an identical temperature. Creep strain at 100 hours is 0.0518% and 0.083% at creep conditions of 175°C/75 MPa and 200°C/60 MPa, respectively, which is comparable to MRI230 D and much lower than most of AX series alloys. By the observation and analysis for samples before and after creep tests using a Shimadzu XRD-7000 type X-ray diffractometer(XRD) and a Hitachi S-3400 N type scanning electron microscope(SEM), it was found that Al_2Ca(C15) phase precipitated out of C36 phase or matrix. The cavity formation and connection at the interface of soft matrix and hard intermetallics caused the propagation of cracking along the eutectic phase during creep process and dislocation accommodated grain/phase boundary sliding is expected to be the dominant creep mechanism.展开更多
Enhanced tensile ductilities in coarse grained Al-Mg-Zn and Al-Mg-Fe materials were studied.The materials were Al-2Mg-5Zn,Al-3Mg-5Zn,Al-4Mg-5Zn,Al-3Mg-0.11Fe,Al-3Mg-0.27Fe,and Al-3Mg-0.40Fe.Tensile elongation-to-failu...Enhanced tensile ductilities in coarse grained Al-Mg-Zn and Al-Mg-Fe materials were studied.The materials were Al-2Mg-5Zn,Al-3Mg-5Zn,Al-4Mg-5Zn,Al-3Mg-0.11Fe,Al-3Mg-0.27Fe,and Al-3Mg-0.40Fe.Tensile elongation-to-failure tests were conducted at constant cross-head speed and constant temperatures from 300 to 450℃.Strain rate change tests were conducted at a constant temperature from 300 to 450℃and in strain-rate range from 4.31×10-5to 1.97×10-2s-1.Experimental results show that over 100%ductilities are consistently achieved in these materials.This superplasticity-like behavior is rate-controlled by solute-drag creep.Although ternary Zn and Fe additions do not have an adverse effect on solute-drag creep and ductility,they increase stress exponent and its sensitivity to Mg content during solute-drag creep.展开更多
The design and performance evaluation of a sustained load creep testing machine was undertaken in this research. The design was motivated by the need to make locally available, a cost effective, technically efficient,...The design and performance evaluation of a sustained load creep testing machine was undertaken in this research. The design was motivated by the need to make locally available, a cost effective, technically efficient, and easily operated creep testing facility;for creep behaviour studies of materials. Design drawings and purchase of materials and components for the design were undertaken after thorough evaluation of the following design and materials selection criteria: design principle and theory, local availability of raw materials and components required for the design, material properties, cost of materials and design, ease of utilization and maintenance, and basis of testing and data capture. The machine casing and frame, heating chamber (consisting of the furnace and a dual specimen mounting stage), load lever and hanger system, and the electro-technical components;were fabricated and coupled following the produced design specifications. The machine was tested and its performance was assessed using its heating efficiency, repeatability and reproducibity of experimental test results, maintainability and cost-effectiveness as criteria. It was observed from repeat tests that the machine has the capacity of generating reliable data for computing creep strain-time results. The efficiency and temperature regulating capacity of the heating unit of the machine were also observed to be very satisfactory. The cost of the design was about 112,000 Naira ($700.00) which is cheaper in comparison to similar commercial creep testing machines from abroad. The machine was also found not to pose maintenance or repairs challenges.展开更多
基金Funded by the Tianjin Research Program of Application Foundation and Advanced Technology(12JCYBJC32100)the Scientific Research Foundation for the Returned Overseas Chinese Scholars,State Education Ministryin part by Grants-in-Aid from the Japan Society for the Promotion of Science(JSPS)
文摘Instantaneous creep in face-centered cubic metals, 5N Al（99.999%）, 2N Al （99%） and 4N Cu （99.99%） with different grain sizes, was firstly investigated by sudden stress-change experiments at ultra- low strain rates ε ≤10-10 s-1 and temperature T 〈 0.32 Tn. The experimental results indicate that the observed instantaneous creep is strongly dependent on grain size, the concentration of impurity, and stacking fault energy. Creep in high-purity aluminum, 5N Al, with a very large grain size, d 〉 1600μm, shows non-viscous behavior, and is controlled by the recovery of dislocations in the boundary of dislocation cells. On the other hand, for 5N A1 with a small grain size, d=30μm, and low-purity aluminum, 2N A1, with d8= 25μm, creep shows viscous behavior and may be related to ＇low temperature grain boundary sliding＇. For high-purity copper, 4N Cu, with d= 40 grn and lower stacking fault energy, creep shows a non-viscous behavior, and is controlled by the recovery process of dislocations. For all of the samples, creep shows anelastic behavior.
基金This work was financially supported by the National Natural Science Foundation of China (No.90406024).
文摘The strain rate sensitivity to creep of single crystal Cu（110）, metal tantalum, and 128°Y-X LiNbO3 piezoelectric single crystal were measured at room temperature by MTS Nanoindenter XP. Among the three kinds of materials studied, Cu showed the highest degree of resistance to creep-induced deformation, which is followed by Ta, while the LiNbO3 single crystal deformed more readily than the others. The values of the steady-state strain rate sensitivities determined by the indentation methods are in the range of 0.002-0.006, 0.02-0.06 and 0.02-0.03 for Cu, Ta, and LiNbO3, respectively. The mechanisms for the indentation-induced creeping behavior and the factors that influenced the creeping are discussed.
文摘In the present study, creep properties of as-cast Mg-5Al-5Ca-2Sn(AXT552) alloy were investigated by means of a GWT304 creep testing machine at temperatures of 175 °C and 200 °C in the stress range of 35-90 MPa. Results show that creep rates increase with applied stress at an identical temperature. Creep strain at 100 hours is 0.0518% and 0.083% at creep conditions of 175°C/75 MPa and 200°C/60 MPa, respectively, which is comparable to MRI230 D and much lower than most of AX series alloys. By the observation and analysis for samples before and after creep tests using a Shimadzu XRD-7000 type X-ray diffractometer(XRD) and a Hitachi S-3400 N type scanning electron microscope(SEM), it was found that Al_2Ca(C15) phase precipitated out of C36 phase or matrix. The cavity formation and connection at the interface of soft matrix and hard intermetallics caused the propagation of cracking along the eutectic phase during creep process and dislocation accommodated grain/phase boundary sliding is expected to be the dominant creep mechanism.
基金Project(DMR-9702156)supported by the National Science Foundation of USAProject(50801034)supported by the National Natural Science Foundation of ChinaProject(20060425)supported by the Scientific and Technological Research Key Lab Foundation of Liaoning Education Department
文摘Enhanced tensile ductilities in coarse grained Al-Mg-Zn and Al-Mg-Fe materials were studied.The materials were Al-2Mg-5Zn,Al-3Mg-5Zn,Al-4Mg-5Zn,Al-3Mg-0.11Fe,Al-3Mg-0.27Fe,and Al-3Mg-0.40Fe.Tensile elongation-to-failure tests were conducted at constant cross-head speed and constant temperatures from 300 to 450℃.Strain rate change tests were conducted at a constant temperature from 300 to 450℃and in strain-rate range from 4.31×10-5to 1.97×10-2s-1.Experimental results show that over 100%ductilities are consistently achieved in these materials.This superplasticity-like behavior is rate-controlled by solute-drag creep.Although ternary Zn and Fe additions do not have an adverse effect on solute-drag creep and ductility,they increase stress exponent and its sensitivity to Mg content during solute-drag creep.
文摘The design and performance evaluation of a sustained load creep testing machine was undertaken in this research. The design was motivated by the need to make locally available, a cost effective, technically efficient, and easily operated creep testing facility;for creep behaviour studies of materials. Design drawings and purchase of materials and components for the design were undertaken after thorough evaluation of the following design and materials selection criteria: design principle and theory, local availability of raw materials and components required for the design, material properties, cost of materials and design, ease of utilization and maintenance, and basis of testing and data capture. The machine casing and frame, heating chamber (consisting of the furnace and a dual specimen mounting stage), load lever and hanger system, and the electro-technical components;were fabricated and coupled following the produced design specifications. The machine was tested and its performance was assessed using its heating efficiency, repeatability and reproducibity of experimental test results, maintainability and cost-effectiveness as criteria. It was observed from repeat tests that the machine has the capacity of generating reliable data for computing creep strain-time results. The efficiency and temperature regulating capacity of the heating unit of the machine were also observed to be very satisfactory. The cost of the design was about 112,000 Naira ($700.00) which is cheaper in comparison to similar commercial creep testing machines from abroad. The machine was also found not to pose maintenance or repairs challenges.
