Simulating the Stress-Strain Response of Building under Oscillating Wind Conditions

Wind load is one of the main lateral control loads that need to be considered in the design of high-rise building structures. It is also of great engineering significance to study the influence of static wind load or time-varying wind load on the dynamic response of structures. In this paper, a high-rise building with a rectangular section (46.8 m × 27 m × 33 m) is simulated based on Ansys18.0 APDL software. The real situation of its response under no lateral wind load and different fluctuating wind load conditions is simulated and the stress and strain response of the building under steady-state and time-varying wind load is given. The results show that the upper strain of the structure under wind load is about 1/1000 of the bottom strain, and the strain of the structure shows obvious accumulation from the top to the bottom, that is, the bottom strain of the building will be higher than the top strain. The influence of time-varying wind load on building structure is related to the loading position of wind load on the structure. The results provide a basis for the structural wind resistance design of this type of building.

Dynamic behaviour of weathered red mudstone in Sichuan(China)under triaxial cyclic loading

The construction of a high-speed railway(HSR) in Southwest China is being hindered by a severe shortage of high-quality subgrade materials. However, red mudstone is widely distributed in the Sichuan Basin of China. The ability to use weathered red mudstone(WRM) to fill subgrade beds by controlling its critical stress and cumulative strain would enable substantial savings in project investments and mitigate damage to the ecological environment. To better understand the dynamic behaviour of WRM, both monotonic and cyclic triaxial tests were performed. The evolution of the cumulative strain vs. increased loading cycles was measured. The influences of confining pressure and loading cycles on the dynamic modulus, damping ratio, critical cyclic stress ratio(CSR), and dynamic stress level(DSL) were investigated. The relationship between the CSR and loading cycles under different failure strain criteria(0.1%-1.0%) was analysed. The prediction model of cumulative strain was also evaluated. The results indicated that the shear strength of WRM sufficiently meets the static strength requirements of subgrade. The critical dynamic stress of WRM can thus satisfy the dynamic stress-bearing requirement of the HSR subgrade. The critical CSR decreases and displays a power function with increasing confining pressure. As the confining pressure increases, the DSL remains relatively stable, ranging between 0.153 and 0.163. Furthermore, the relationship between the dynamic strength and loading cycles required to cause failure was established. Finally, a newly developed model for determining cumulative strain was established. A prediction exercise showed that the model is in good agreement with the experimental data.

Effect of microvoids on microplasticity behavior of dual-phase titanium alloy under high cyclic loading(Ⅰ):Crystal plasticity analysis

A crystal plasticity finite element(CPFE)model was established and 2D simulations were carried out to study the relationship between microvoids and the microplasticity deformation behavior of the dual-phase titanium alloy under high cyclic loading.Results show that geometrically necessary dislocations(GND)tend to accumulate around the microvoids,leading to an increment of average GND density.The influence of curvature in the tip plastic zone(TPZ)on GND density is greater than that of the size of the microvoid.As the curvature in TPZ and the size of the microvoid increase,the cumulative shear strain(CSS)in the primaryα,secondaryα,andβphases increases.Shear deformation in the prismatic slip system is dominant in the primaryαphase.As the distance between the microvoids increases,the interactive influence of the microvoids on the cumulative shear strain decreases.

Ratcheting boundary of 316LN austenitic stainless steel under thermal aging

Previous studies,including ASME and RCC-MR standards,did not consider the influence of environmental factors on the ratcheting boundary of the material,and only a unified ratcheting boundary was proposed.In this paper,thermal aging was taken into consideration,and the effect of thermal aging time on the ratcheting boundary of 316 LN austenitic stainless steel was characterized by the efficiency diagram rule.The results show that,when the secondary ratio U is small,there is no significant difference in ratcheting boundary between the original material and the thermal aged material.When the secondary ratio U is large,the ratcheting boundary of the material presents a slight upward trend with the increase of thermal aging time.Compared with ASME and RCC-MR standards,it is found that RCC-MR is conservative.Based on the evolution of the efficiency index V with the number of cycles,it is more conservative and reasonable to choose the stage when the efficiency index V develops into a constant.

Fatigue crack propagation across grain boundary of Al-Cu-Mg bicrystal based on crystal plasticity XFEM and cohesive zone model

In this paper,a methodology integrating crystal plasticity(CP),the eXtended finite element method(XFEM)and the cohesive zone model(CZM)is developed for an Al-Cu-Mg alloy to predict fatigue crack propagation(FCP)across grain boundary(GB)of Al-Cu-Mg alloy during stageІІ.One GB model is incor-porated into FCP constitutive law to describe grain interaction at GB.A bicrystal containing GB is built up to simulate FCP behavior through L participated GBs.Modelling features including GB characteristic,cumulative plastic strain(CPS)distribution and crystal slipping evidence can be identified.The numer-ical results are compared with published experimental data to check the accuracy of model.This work demonstrates that the combination of CP containing GB constitutive laws,XFEM and CZM is a promising methodology in predicting twist angle-controlled crack deflection through GBs.