The Influence of CO_(2) Cured Manganese Slag on the Performance and Mechanical Properties of Ultra-High Performance Concrete

The presence of toxic elements in manganese slag(MSG)poses a threat to the environment due to potential pollution.Utilizing CO_(2) curing on MS offers a promising approach to immobilize toxic substances within this material,thereby mitigating their release into the natural surroundings.This study investigates the impact of CO_(2) cured MS on various rheological parameters,including slump flow,plastic viscosity(η),and yield shear stress(τ).Additionally,it assesses flexural and compressive strengths(f_(t) and f_(cu)),drying shrinkage rates(DSR),durability indicators(chloride ion migration coefficient(CMC),carbonization depth(CD)),and the leaching behavior of heavy metal elements.Microscopic examination via scanning electron microscopy(SEM)is employed to elucidate the underlying mechanisms.The results indicate that CO_(2) curing significantly enhances the slump flow of ultra-high performance concrete(UHPC)by up to 51.2%.Moreover,it reduces UHPC’sηandτby rates ranging from 0%to 52.7%and 0%to 40.2%,respectively.The DSR exhibits a linear increase corresponding to the mass ratio of CO_(2) cured MS.Furthermore,CO_(2) curing enhances both f_(t) and f_(cu) of UHPC by up to 28.7%and 17.6%,respectively.The electrical resistance is also improved,showing an increase of up to 53.7%.The relationship between mechanical strengths and electrical resistance follows a cubic relationship.The CO_(2) cured MS demonstrates a notable decrease in the CMC and CD by rates ranging from 0%to 52.6%and 0%to 26.1%,respectively.The reductions of leached chromium(Cr)and manganese(Mn)are up to 576.3%and 1312.7%,respectively.Overall,CO_(2) curing also enhances the compactness of UHPC,thereby demonstrating its potential to improve both mechanical and durability properties.

Effect of CSH Crystal Nucleus on Steam-Free Cured Fly Ash Precast Concrete Components

The measures of steam curing and early-strengthening agents to promote the precast components to reach the target strength quickly can bring different degrees of damage to the concrete.Based on this,the new nanomaterial CSH-the hydration product of cement effectively solves these measures’disadvantages,such as excessive energy consumption,thermal stress damage,and the introduction of external ions.In this paper,the effect of CSH on the early strength of precast fly ash concrete components was investigated in terms of setting time,workability,and mechanical properties and analyzed at the microscopic level using hydration temperature,XRD,and SEM.The results showed that under the same workability,CSH could significantly reduce the amount of admixture,shorten the final setting time,almost not affect the initial setting time,and accelerate the hydration of cement.At the optimum dose of 5%,the mechanical properties of the specimens were improved by more than 98%within 12 h of hydration,resulting in an earlier release time of 12 h and no risk of strength inversion later.The results of this paper give theoretical support to the behavior of precast components under steam-free curing.

Effects of Different Baking Processes on Carotenoid Content in Upper Leaves of Fluecured Tobacco

[Objective] We aimed to improve the quality of flue-cured tobacco with K326 upper leaves and explore the optimal tobacco baking process in Chongqing tobacco-producing region. [Method] Four different baking processes （endogenetic force moisture-removing flue-curing technique, exogenetic force moisture-removing flue-curing technique, three-stage flue-curing process, three-stage and six-step flue- curing process） were adopted in this research to investigate the effects of different baking processes on carotenoid content of same-maturity degree upper leaves of the flue-cured tobacco K326. [Result] The results showed at the yellowing and color fixing stages, the carotenoids were most fully decomposed in endogenetic force moisture-removing flue-curing technique. The decomposed carotenoid content was lowest in exogenetic force moisture-removing flue-curing technique, for which the carotenoid content was highest （50.53 mg/g）. [Conclusion] At the yellowing and color fixing stages, exogenetic force moisture-removing flue-curing technique was most conducive to the carotenoid accumulation in tobacco baking process.

Study on Loading Leaves Density with Cage Clamp on Quality of Cured Tobaccos in Bulk-Curing Barn

In order to determine the best loading density of tobacco leaf with cage clamp in bulk-curing barns, a curing test was conducted on middle-part tobacco leaves. The results showed that for good appearance quality of cured tobacco, the loading density at 59.52 kg/m2 （4 000 kg/barn） was the best, fol owed by 66.96 kg/m2 （4 500 kg/barn） and 74.40 kg/m2 （5 000 kg/barn）. As leaf loading density increased, the contents of leaf nicotine and total nitrogen increased, sugar content had smal changes, the ratio of sugar to nicotine decreased and tended to be balanced and the content of neutral aroma substances was decreasing, but the difference among treatments was not significant. With the increase of loading density, the sensory quality of cured leaf was better. When leaf loading density was 66.96 kg/m2 （4 500 kg/barn）, apperance quality of cured leaf improved considerably, with prominent aro-ma. Therefore, the best loading density of tobacco leaf in cage clamp of bulk-curing barn would be 66.96 kg/m2 （4 500 kg/barn） .

Curing Characteristics and Suitable Harvest Maturity of Fresh Flue-cured Tobacco Leaves in Ankang Tobacco Growing Areas

CuItivars K326, Yunyan 87 and Guiyan 4 were used to investigate the curing characteristics and suitabIe harvest maturity of fresh fIue-cured tobacco Ieaves in Ankang tobacco growing areas. ResuIts indicated that the water Ioss of K326 was sIow,and the Ieaves were resistant to curing and reIative easiIy to cure. The water Ioss of Yunyan 87 and Guiyan 4 were quick, and the Ieaves with normal resistance to curing were reIative difficuIt to cure. For Guiyan 4, the shrinkage of CM1 maturity was the Iargest. For K326 and Yunyan 87, the shrinkages of CM2 maturity were the Iargest whiIe the shrinkage of CM1 maturity was the Iowest, but the difference did not reach statistical significance. The proportion of top-middIe-grade tobacco Ieaves and average price for K326 were the highest with XM2, CM2 and BM2 maturity, and for Yunyan 87 were XM1, CM3 and BM2 maturity. For K326, Ieaves with XM2, CM2 and BM2 maturity showed the balanced chemical components and the best smoking quality.

Effects of Two Curing Methods on Quality of Yellow Sun-cured Tobacco

[Objective] The aim was to research effects of bamboo split curing method and steely barn curing method on quality of yellow sun-cured tobacco, providing scientific references for optimization of curing technology of yellow sun-cured tobacco. [method] The tobaccos were divided into two groups treated with two methods and the related indices of treated tobaccos were then measured to evaluate effects of curing methods on quality of yellow sun-cured tobacco. [Result] Tobaccos treated with two methods were all dominated by reddish yellow and yellow; exterior quality differed little. In detail, total sugar and reducing sugar in an average level in three locations were all higher with method A than those with method B, but nicotine and total N were lower; comprehensive chemical components in group with method B proved more appropriate with higher K. In addition, sensory qualities of leaves in moderate and bottom locations were better with method B compared with method A; sensory quality of top leaves was better; comprehensive sensory quality of leaves treated with method B proved better. On the other hand, cost for method A was 2.82 times of method B; the area of sun-curing field was 3.27 times and manage- ment work was 1.77 times, which indicated that method B is low-cost and time-saving, which would be a guarantee of tobacco quality. [Conclusion] The research provides scientific references for rational use of tobacco resources and optimization of sun-curing technology.

Effects of Different Flue-curing Barns on Aroma Quality of Upper Flue-cured Tobacco Leaves of K326

[Objective] This study was conducted to compare the aroma quality of up-per leaves of K326 flue-cured in different barns, and provide theoretical references for the development and optimization of bulk curing barn and the supporting tech-niques. [Method] The upper leaves of K326 were flue-cured in a commonness barn, a four-shelf bulk curing barn and a three-shelf bulk curing barn separately, and then the contents of aroma components and taste quality indices of the finished leaves were measured and compared. [Result] The contents of total aroma components, chromoplast pigment degradation products, phenylalanine aroma components and neophytadiene showed no significant differences in the leaves flue-cured in four-shelf bulk curing barn and commonness barn, but were significantly or very significantly higher than those in the leaves flue-cured in three-shelf bulk curing barn. The con-tents of carotenoid degradation products, Mail ard reaction products, cembranes aro-ma components and total aroma components （except neophytadiene） showed no significant difference among the three treatments. The results of sensory evaluation revealed that the sensory taste of the leaves flue-cured in four-shelf bulk curing barn was the best, as the finished leaves had rich, delicate aroma, comfortable and clean aftertaste. The leaves flue-cured in commonness barn was better than those flue-cured in three-shelf bulk curing barn in aroma quality, amount and aftertaste. [Conclusion] The four-shelf bulk curing barn had a large volume for tobacco leaf processing, but a similar baking environment to the commonness barn, which is conducive to the formation and accumulation of aroma components, so the finished leaves had similar appearance and quality with those flue-cured in commonness barn. The upper flue-cured leaves in three-shelf bulk curing bran had poorer quality than those flue-cured in the other two barns.

Yield and Nicotine Content of Flue-Cured Tobacco as Affected by Soil Nitrogen Mineralization

Nitrogen(N)supply is the most important factor affecting yield and quality of flue-cured tobacco(FCT).A field experiment and an in situ incubation method were used to study the effects of soil N mineralization in the later stages of growth on yield and nicotine content of FCT in Fenggang and Jinsha,Guizhou Province.The yield and market value of FCT at Fenggang were much lower than those at Jinsha.However,the nicotine content of middle and upper leaves was much higher at Fenggang than at Jinsha when the same rate of fertilizer N was applied,which might be due to a higher N supply capacity at the Fenggang site.At later stages of growth(7-16 weeks after transplanting),the soil net N mineralization at Fenggang(56 kg N ha^(-1))was almost double that at Jinsha(30 kg N ha^(-1)).While soil NH_4-N and NO_3-N were almost exhausted by the plants or leached 5 weeks after transplanting,the N taken up at the later growth stages at Fenggang were mainly derived from soil N mineralization,which contributed to a high nicotine content in the upper leaves.The order of soil N contribution to N buildup in different leaves was:upper leaves>middle leaves>lower leaves.Thus,soil N mineralization at late growth stages was an important factor affecting N accumulation and therefore the nicotine content in the upper leaves.

Influence of subsequent curing on water sorptivity and pore structure of steam-cured concrete

Steam-cured condition is found to cause larger porosity and worse properties of concrete compared with normal curing condition. For the sake of seeking effective measurements to eliminate this bad effect of steam-cured condition on concrete, the water sorptivity and pore structure of steam-cured concretes exposed to different subsequent curing conditions were investigated after steam-curing treatment. The capillary absorption coefficient and porosity of the corresponding concretes were analyzed, and their mechanisms were also discussed. The results indicate that water sorptivity and pore structure of steam-cured concrete are greatly influenced by the curing condition used in subsequent ages. Exposure steam-cured concrete to air condition has an obviously bad effect on its properties and microstructures. Adopting subsequent curing of immersing steam-cured concrete into about 20℃ water after steam curing period can significantly decrease its capillary absorption coefficient and porosity. Steam-cured concrete with 7 d water curing has minimum capillary absorption coefficient and total porosity. Its water sorptivity is decreased by 23% compared with standard curing concrete and the porosity is 9.6% lower. Moreover, the corresponding gradient of water sorptivity and porosity of steam-cured concrete both decrease, thus mictostructure of concrete becomes more homogeneous.

Optimization of a new animal glue binder system cured by CO_2 for use in foundry

A new sand binder system cured by CO2 was prepared based on the animal bone glue.To overcome the disadvantages of animal glue such as agglomeration at room temperature,high energy consumption and low efficiency,an alkaline decomposition process was selected,and certain modifier was used to modify the performance of the animal glue binder.For the alkaline decomposition,NaOH was used as the catalyst with an addition of 4wt.% to the animal glue.A modifier was determined through the orthogonal experiment with a weight ratio of glycerin:glycol:dextrin:animal glue = 9:16:15:100,and the optimal modification reaction should be performed at 75 ℃ with a reaction time of 90 min.Ca(OH)2 was used as a promoter;the optimal CO2 gas flux blowing into the sand was 0.7 m3.h-1 for a duration of 60s under the experimental conditions.Results show that an original strength above 0.7 MPa and a final strength about 4.2 MPa can be achieved,which could meet the requirement of rapid moulding and core-making for foundry.The new binder was characterized and analyzed by means of IR,and the modification and CO2-cured mechanisms of this animal glue binder were also discussed.

Follow-up Study of Retreatment TB Patients with Sputum Smear and/or Culture Positive Two Years after They were Declared Cured with First-line Anti-TB Drugs in Shandong Province

This study aimed to learn the recurrence rate in the retreatment TB patients with sputum smear and/or culture positive （ss＋ and/or c＋） two years after they were declared cured, and to explore causes of recurrence in order to improve long-time treatment outcome. 5 cities were selected as research locations. Recurrence of TB was judged by chest X-ray examination together with sputum smear and culture examination.

Characteristic and effect analysis of protein and peptide in Cantonese cured meat processing

The aim of this work was to explore the physicochemical and structural properties,lipid oxidation and antioxidant capacity of the peptides extracted from Cantonese cured meat and as well as to investigate the effect of drying time on the sarcoplasmic and myofibrillar proteins of Cantonese cured meat.The results suggested that salting out,protein oxidation and heat treatment were closely related to surface hydrophobicity and the secondary structure of peptides was changed by processing.And the peroxide value and the value of tributyltin compounds were different in evaluating the degree of lipid oxidation.Glu and His were the major amino acid.The approximate molecular weights of the sarcoplasmic proteins and myofibrillar proteins ranged from 31 kDa to 50 kDa and 66 kDa,respectively.The results indicated that reducing the levels of protein oxidation and improvement of the antioxidant properties should be of great interest to preserve the nutritional quality of meat products and prolong preservation period.

Screening of Low Tar Flue Cured Tobacco Varieties

The main agronomic traits,economic traits,appearance quality,main chemical components,gas composition and physical parameters of 10 flue cured tobacco varieties were investigated in the experiment.And the field natural incidence of the main diseases was investigated.The results showed that main agronomic characters of the 10 varieties were in line with the breeding objectives,among which 5 varieties have good economic characters;5 varieties have good appearance quality;6 varieties have coordinated chemical composition and high potassium content;9 varieties have good smoke components and physical indicators.

Buildings and civil engineering works-Sealants-Determination of changes in cohesion and appearance of elastic weatherproofing sealants after exposure of statically cured specimens to artificial weathering and mechanical cycling

Foreword ISO(the International Organization for Standardization)is a worldwide federation of national standards bodies(ISO member bodies).The work of preparing International Standards is normally carried out through ISO technical committees.Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee.

Nosocomial infection in patients with ventricular hemorrhage cured by lateral ventricle drainage: An analysis of 41 cases

Objective To analyse infection rate of ventricular hemorrhage after lateral ventricle drainage and evaluate the method and measure of precaution. Methods Patients were divided into first and second groups according to the remaining time of drainage tube and into A and B groups according to drainage in one or two sides. After operation the infection condition of insert tube was observed and blood was cultivated regularly. Results The infection rate in the first group was significantly shorter than that in the second one (P 【 0. 01), while it was no significantly difference between groups A and B (P 】 0. 05). Conclusion To remain drainage tube for one to two weeks is safer than for more than two weeks. The infection rate is higher in group with drainage in two sides than in one. In addition, it is obviously related to the patient’s body condition and immunity. 6 refs,2 tabs.

Study of the structure and the mechanical properties of dynamically cured PP/MAH-g-SEBS/epoxy blends

A new method concerning with the simultaneous reinforcing and toughening of polypropylene （PP） was reported. Dynamical cure of the epoxy resin was successfully applied in the PP/maleic anhydride-grafted styrene-ethylene-butylene-styrene （SEBS） triblock copolymer, and the obtained blends named as dynamically cured PP/MAH-g-SEBS/epoxy blends. The stiffness and toughness of the blends are in a good balance, and MAH-g-SEBS was acted as not only an impact modifier but also a compatibilizer. The structure of the dynamically cured PP/MAH-g-SEBS/epoxy blends is the embedding of the epoxy particles by the MAH-g- SEBS.C2009 Xue Liang Jiang. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.

The Mechanism of Carotenoid Degradation in Flue-Cured Tobacco and Changes in the Related Enzyme Activities at the Leaf-Drying Stage During the Bulk Curing Process

The mechanism of carotenoid degradation and the changes in the activities of related enzymes in flue-cured tobacco at the leaf-drying stage during the bulk-curing process were studied in order to provide theoretical basis for optimization of curing technology. The effect of different rising speeds of temperature on the carotenoid degradation and the related enzymes activities at the color-fixing stage during the bulk curing process was studied by using the electric-heated fluecuring barn designed by Henan Agricultural University, China, based on curing technology with yellowing at low temperature and moderate humidity and leaf drying at moderate humidity. The results showed that the carotenoid degradation components （β-carotene, lutein, neoxanthin, and violaxthin） decreased gradually at the color-fixing stage during the bulk curing process. The carotenoid degradation components viz.,β-carotene, lutein, neoxanthin, and violaxthin at the slow heating curing （T1） were relatively higher than the rapid heating curing （T2） accounting for 10, 2, 32 and 32% respectively, but there were no differences among treatments （P〉 0.05）. The effect of different conditions of curing on the activities of enzymes related to carotenoids degradation were significant. The lipoxygenase, phenylalanine ammonialyase, peroxidase, and polyphenol oxidase enzymes had a bidirectional effect on the quality of tobacco leaves and it was beneficial to form more premise matter of aroma based on the higher enzyme activities at the early leaf-drying stage. The slow heating could regulate the change in various enzymes＇ activities reasonably, making cell redox reaction to reach the dynamic balance and make the degradation of carotenoids adequately. Meanwhile, it could avoid the occurrence of browning reaction and provide foundation for improving the quality of tobacco and optimization of technology for bulk curing and further enhancing aroma.

Experimental studies on the utilization of steel slag in the steam-cured concrete

The possibility of applying steel slag as mineraladmixture in steam-cured concrete was investigated. Thecompressive strength, chloride permeability, carbonationdepth and drying shrinkage of concrete and the microstructurecharacteristics of hardened paste were studied. Results showthat the steam-cured concrete containing steel slag at a highwater-to-binder ratio has low compressive strength, coarsepore structure, moderate permeability, large carbonation depthand great drying shrinkage. The negative effects of steel slagon the mechanical and durability performance of steam-curedconcrete become smaller at a low water-to-binder ratio or byadding ultrafine ground granulated blast furnace slag（UGGBS）. The later-age hydration of cement is significantlypromoted by adding steel slag. The pozzolanic reaction andmicro-filler effect of UGGBS result in dense structure, whichmakes great contribution to the strength development anddurability performance of steam-cured concrete. These effectsof steel slag and UGGBS are significant at a low water tobinder ratio. The steam-cured concrete containing steel slag-UGGBS blended mineral admixture at a low water-to-binderratio has the best performance with high compressive strength,fine pore structure and good durability.

Research on non-steam-cured and non-fired fly-ash thermal insulating materials

A thermal insulating material is synthesized via a non-steam-cured and non-fired route by using fly-ash, sorel cement and hydrogen peroxide solution as raw material. Properties such as apparent density, compressive strength, bending strength, thermal conductivity, water resistance, and thermal tolerance of this matrial are studied, some influencing factors on its performance discussed. This material has an apparent density of 360 kg/m^3, a compressive strength of 1.86 MPa, a thermal conduction coefficient of 0.072 W/（m·K）, a softening coefficient of 0.55, and a thermal tolerant temperature of 300 ℃. Test results show that this material is light in weight, of high strength, and good thermal insulation. In addition, neither steam-curing nor sintering is needed in producing it. Further more, large amount of fly ash is used in this material, making it a low cost and environment-friendly building material.