A Novel Crowbar Impulse Current Circuit for Testing the Switch-Type SPD

A crowbar impulse current circuit for testing the switch-type surge protective device （SPD） is presented. The crowbar circuit consists of a computer control circuit, a trigger voltage pulse generator, a main discharging switch, and a crowbar pseudospark switch. The active trigger technology was studied in the crowbar impulse current circuit. The circuit monitors the main discharging current and generates a trigger signal at a proper time for the crowbar pseudospark switch operation. The trigger characteristics of the main discharge switch and the crowbar pseu- dospark switch were investigated. By monitoring the preset applied capacitor voltage, the gap distance of the main discharging switch could be adjusted to ensure a discharging delay time less than 2 μs. Equipped with a surface ttashover trigger device made of high relative perimittivity dielectric material BaTiO3 （εr = 3460）, the discharge delay time of the crowbar pseudospark switch is less than 85 ns, and the minimum operating voltage is less than 1% of its self-breakdown voltage. With a storage capacitor of 9 μF , an inductor of 18 μH and a crowbar pseudospark switch, a load of 30 mΩ and an applied capacitor voltage of 40 kV, an impulse current waveform of maximum 25 kA was generated with a rise time and time to half peak value of 17.2 μs and 336μs respectively.

Origin of Initial Current Peak in High Power Impulse Magnetron Sputtering and Verification by Non-Sputtering Discharge

A non-sputtering discharge is utilized to verify the effect of replacement of gas ions by metallic ions and consequent decrease in the secondary electron emission coefficient in the discharge current curves in high-power impulse magnetron sputtering （HiPIMS）. In the non-sputtering discharge involving hydrogen, replacement of ions is avoided while the rarefaction still contributes. The initial peak and ensuing decay disappear and all the discharge current curves show a similar feature as the HiPIMS discharge of materials with low sputtering yields such as carbon. The results demonstrate the key effect of ion replacement during sputtering.

A Novel Starting Impulse Suppression Method for Active Power Filter Based on Slowly Rising Curve

With the widespread application of power electronic equipment in the power grid,the harmonic problem of the power grid becomes more pronounced,reducing the efficiency of power production,transmission,and utilization,and interfering with the normal operation of the power grid.Based on the requirements of harmonic suppression and power system protection,a shunt active power filter(SAPF)is proposed as an effective harmonic suppression method.However,there are problems with impulse current and impulse voltage in the starting process of SAPF.Impulse current and impulse voltage cause the power grid and switchgear to bear greater current stress and voltage stress,which seriously affect the security and reliability of the power grid and may damage the switchgear.To effectively solve the problem of impulse current and impulse voltage,the starting process of SAPF is divided into the uncontrolled rectification stage and the transition stage.The mathematical model of the DC side of APF is established.The causes of impulse current and impulse voltage in the uncontrolled rectifier and transition phases are analyzed.By introducing voltage square,a new starting impulse suppression strategy of active power filter based on the slow rising curve is proposed,fundamentally solving the problems of impulse current and impulse voltage.Simulation results verify the effectiveness and feasibility of this method.

多次雷电冲击对氧化锌避雷器阀片性能的影响(英文)

A lightning arrester is used for electrical equipment protection against damage due to lightning strikes.One example of protected electrical equipment is electrical power transformer.If there is no lightning arrester installed to the transformer,when a lightning strike happens,it may receive a very high lightning overvoltage,which is certainly resulted in the transformer damage at its insulation.Usually,a lightning arrester specification data attached to a lightning arrester contains the rating data of the lightning arrester current and voltage.In the use of lightning arrester,the possibility of receiving multiple lightning strikes is not taken into account sometimes.In fact,in some places,the number of multiple strikes in short duration is quiet high in number.This condition makes the lightning arrester being stroked by multiple lightning strikes.Therefore,it may change the lightning arrester's properties,and then the arrester may not be able to provide good electrical equipment protection against lightning strike anymore.This condition will result in great loss to electrical companies and electrical consumers.Therefore,this research studied the effect of applying multiple lightning strikes to ZnO lightning arrester block.Every time a group of lightning impulse current is applied to the ZnO lightning arrester block,it is followed by the measuring of its 50 Hz voltage and current characteristic. The changing in the ZnO lightning arrester block 50 Hz characteristic then can be analyzed.It was found that by applying more numbers of lightning strikes which made the arrester becoming worse,even though,actually,the lightning impulse peak current was still under the rating of the lightning arrester current.In this case for a 5 kA,24 kV lightning arrester,even though the lightning impulse peak current flowing through the ZnO lightning arrester block was still 2500 A,the lightning arrester ZnO block had already been damaged.Having been damaged,an alternating current flowing through the damaged ZnO block was about 10000 times as much current flowing to the good one.The maximum of impulse energy absorbed by a ZnO block recorded was 334.7 J/cm^3.The damaged ZnO block should be replaced by a good one.

实际接地系统的冲击特性试验研究(英文)

In this work,the results of an experimental study of the impulse characteristic of practical ground electrodes consisting of horizontal conductors of various lengths and full-scale tower footings were reported.These electrodes were installed at an outdoor test site having nonuniform soil,with equipment facilities for generating low-and high-magnitude impulse currents.The tests on the horizontal electrode were used to determine the effective length,the voltage and current distribution along the electrode length and the effect of the injection point along the electrode.The tests on the tower footings were used to determine impulse resistance and demonstrate its non-linear variation with current magnitude.Computer simulations of the test electrodes using the electromagnetic field method showed good agreement with the measured result.

Characterization and comprehension of corona partial discharge in air under power frequency to very low frequency voltage

For the partial discharge test of electrical equipment with large capacitance,the use of lowfrequency voltage instead of power frequency voltage can effectively reduce the capacity requirements of test power supply.However,the validity of PD test under low frequency voltage needs to be evaluated.In order to investigate the influence of voltage frequency on corona discharge in the air,the discharge test of the tip-plate electrode under the frequency from 50 to0.1 Hz is carried out based on the impulse current method.The results show that some of the main features of corona under low frequency do not change.The magnitude of discharge in a positive half cycle is obviously larger than that in a negative cycle.The magnitude of discharge and interval in positive cycle are random,while that in negative cycle are regular.With the decrease of frequency,the inception voltage increases.The variation trend of maximum and average magnitude and repetition rate of the discharge in positive and negative half cycle with the variation of voltage frequency and magnitude is demonstrated,with discussion and interpretation from the aspects of space charge transportation,effective discharge time and transition of discharge modes.There is an obvious difference in the phase resolved pattern of partial discharge and characteristic parameters of discharge patterns between power and low frequency.The experimental results can be the reference for mode identification of partial discharge under low frequency tests.The trend of the measured parameters with the variation of frequency provides more information about the insulation defect than traditional measurements under a single frequency（usually 50 Hz）.Also it helps to understand the mechanism of corona discharge with an explanation of the characteristics under different frequencies.

Enhancement of Soil Discharge Channels on Potential Surrounding Buried Cables Under Impulsive Currents

Substations have a large number of signal transmission cables beneath the ground.Both the insulation safety and signal reliability of the cables are affected severely by the electromagnetic field.Under high-amplitude impulsive currents,the dispersion of currents can cause soil discharge and thus cause unexpected distortions in an electromagnetic field.This paper focuses on the distortions of the electric field.In general,soil discharge channels occur in the vicinity of the independent rod.Closer development of the channel might enhance the electric field distribution and the potential surrounding the outer insulation of the cables(i.e.the surface potential on the cable).Therefore,this paper establishes a platform for observing the soil discharge channel and measuring the surface potential.Direction characteristic of the channel is extracted from the captured image of soil discharge channels and the surface potential is obtained by the measured coupling capacitive current on the shield experimentally.This paper also presents an improved model considering a dynamic growing discharge channel for the transient analysis of the grounding electrode.Study results show the surface potential increases as the discharge channel approaches the cable.To quantify this enhancement effect,the ratio of the highest to the lowest value of surface potential in different directions is taken as the multiple of the surface potential increase.The calculated multiples of the surface potential increase are in the range of 1 to 1.64 times under different conditions by the improved model.Therefore,taking the soil discharge channel into account is helpful to accurately analyze the impulsive interference of buried cables.