DESIGN OF TERNARY CURRENT-MODE CMOS CIRCUITS BASED ON SWITCH-SIGNAL THEORY

By applying switch-signal theory, the interaction between MOS transmission switch-ing transistor and current signal in current-mode CMOS circuits is analyzed, and the theory oftransmission current-switches which is suitable to current-mode CMOS circuits is proposed. Thecircuits, such as ternary full-adder etc., designed by using this theory have simpler circuit struc-tures and correct logic functions. It is confirmed that this theory is efficient in guiding the logicdesign of current-mode CMOS circuits at switch level.

DESIGN OF SYMMETRIC TERNARY CURRENT-MODE CMOS CIRCUITS

By applying switch-signal theory, the theory of transmission current-switches based on symmetric ternary logic is proposed, this theory is suitable to design symmetric ternary current-mode CMOS circuits. The symmetric ternary current-mode CMOS circuits designed by using this theory not only have simpler circuit structures and correct logic functions, but also can process bidirectional signals.

CURRENT MODE CIRCUIT SYMBOLIC ANALYSIS WITH MATH-EMATICA

A practical method of current mode circuit symbolic analysis using Mathematica is proposed. With the powerful symbolic manipulation capacity of Mathematica, current mode circuit symbolic analysis can be significantly simplified. The active devices are modelled by nullors. The examples of current mode filters using CCIIs are presented.

Simulation realization of skip cycle mode integrated control circuit in the switching power supply with low standby loss

This paper explores and proposes a design solution of an integrated skip cycle mode （SCM） control circuit with a simple structure. The design is simulated and implemented with XD10H-1.0μm modular DIMOS 650 V process. In order to meet the requirement of a wide temperature range and high yields of products, the schematic extracted from the layout is simulated with five process corners at 27℃ and 90℃. Simulation results demonstrate that the proposed integrated circuit is immune to noise and achieves skipping cycle control when switching mode power supply （SMPS） works with low load or without load.

A State Variable Method for the Realization of Universal Current-Mode Biquads

A state variable method of converting single-resistance-controlled- oscillators (SRCO), into universal current-mode biquad (offering realizations of all the five standard filter functions namely, low pass, band pass, high pass, notch and all pass) has been highlighted. The workability of the exemplary implementation of the derived current-mode universal biquad has been demonstrated by PSPICE simulation results based upon 0.35 μ m technology. It is expected that the proposed method can be applied to other SRCOs to generate other multifunction filter structures.

Electronically Controllable Fully-Uncoupled Explicit Current-Mode Quadrature Oscillator Using VDTAs and Grounded Capacitors

An electronically controllable fully uncoupled explicit current-mode quadrature oscillator employing Voltage Differencing Transconductance Amplifiers (VDTAs) as active elements has been presented. The proposed configuration employs two VDTAs along with grounded capacitors and offers the following advantageous features 1) fully and electronically independent control of condition of oscillation (CO) and frequency of oscillation (FO);2) explicit current-mode quadrature oscillations;and 3) low active and passive sensitivities. The workability of proposed configuration has been demonstrated by PSPICE simulations with TSMC CMOS 0.18 μm process parameters.

A Fault Feature Extraction Model in Synchronous Generator under Stator Inter-Turn Short Circuit Based on ACMD and DEO3S

This paper proposed a new diagnosis model for the stator inter-turn short circuit fault in synchronous generators.Different from the past methods focused on the current or voltage signals to diagnose the electrical fault,the sta-tor vibration signal analysis based on ACMD(adaptive chirp mode decomposition)and DEO3S(demodulation energy operator of symmetrical differencing)was adopted to extract the fault feature.Firstly,FT(Fourier trans-form)is applied to the vibration signal to obtain the instantaneous frequency,and PE(permutation entropy)is calculated to select the proper weighting coefficients.Then,the signal is decomposed by ACMD,with the instan-taneous frequency and weighting coefficient acquired in the former step to obtain the optimal mode.Finally,DEO3S is operated to get the envelope spectrum which is able to strengthen the characteristic frequencies of the stator inter-turn short circuit fault.The study on the simulating signal and the real experiment data indicates the effectiveness of the proposed method for the stator inter-turn short circuit fault in synchronous generators.In addition,the comparison with other methods shows the superiority of the proposed model.

A VERSATILE CURRENT-MODE BIQUAD USING OPERATIONAL AMPLIFIERS

A versatile current-mode biquadratic filter using three operational amplifiers and nine passive elements is proposed. By suitably choosing the output branch, lowpass, bandpass, highpass, bandstop and allpass transfer functions are realized simultaneously without changing the circuit configuration and elements. Two circuits, one is for low frequency application and the other for high frequency, are proposed. The center frequency, quality factor and gain constants of the circuit can be tuned independently. Simulated results show that the circuits work successfully.

Electronically-Controlled Current-mode second order Sinusoidal Oscillators Using MO-OTAs and Grounded Capacitors

Five new electronically-controllable second order current-mode sinusoidal oscillators using three mul-ti-output operational transconductance amplifiers (MO-OTAs) and two grounded capacitors (GC) have been presented. Simulation results are included to confirm the theoretical analysis based upon CMOS OTAs implementable in 0.5 μm technology.

Universal Current-Mode Biquad Employing Dual Output Current Conveyors and MO-CCCA with Grounded Passive Elements

A new universal multiple input multiple output (MIMO) type current-mode biquad employing two dual output current conveyors (DOCCII), one multiple output current controlled current amplifier (MOCCCA) and four passive grounded elements is proposed which can realize all the five basic filtering functions namely, low-pass (LP), high-pass (HP), band-pass (BP), band-stop (BR) and all-pass (AP) in current mode from the same configuration. The centre frequency can be set by the passive elements of the circuit and the quality factor Q0 is electronically tunable through bias currents of the MOCCCA. Therefore, the biquad filter has independent tenability for the and Q0. The active and passive sensitivities of Q0 and are low. The workability of the new configuration has been demonstrated by PSPICE simulation results based upon a CMOS CCII in0.35μm technology.

An Adaptive Slope Compensation Circuit for Peak Current Mode of Boost Switching Power Supply

Based on the analysis of the basic principle of slope compensation, a high-precision adaptive slope compensation circuit for peak current mode boost DC/DC converter is designed. The circuit dynamically detects the input and output voltage of the boost circuit to realize automatic adjustment of the compensation amount with the change of duty ratio, which makes the ramp compensation slope optimized. The design uses a high-precision subtracter to improve the accuracy of slope compensation. While eliminating sub-slope oscillation and improving the stability of boost circuit, the negative impact of compensation on boost circuit is minimized, and the load capacity and transient response speed of boost circuit are guaranteed. The circuit is designed based on SMIC 0.18um CMOS technology, with simple structure, high reliability and easy engineering implementation. Spectre circuit simulator 17.1.0.124 64b simulation results show that the circuit has high compensation accuracy and wide input and output voltage range. When the working voltage is 3.3 V, the compensation slope can be adjusted adaptively under different duty cycles, and the minimum error between the compensation slope and the theoretical optimal compensation slope is only 0.42%.

Thermal runaway evolution of a 280 Ah lithium-ion battery with LiFePO_(4) as the cathode for different heat transfer modes constructed by mechanical abuse

Lithium iron phosphate batteries have been increasingly utilized in recent years because their higher safety performance can improve the increasing trend of recurring thermal runaway accidents.However,the safety performance and mechanism of high-capacity lithium iron phosphate batteries under internal short-circuit challenges remain to be explored.This work analyzes the thermal runaway evolution of high-capacity LiFePO_(4) batteries under different internal heat transfer modes,which are controlled by different penetration modes.Two penetration cases involving complete penetration and incomplete penetration were detected during the test,and two modes were performed incorporating nails that either remained or were removed after penetration to comprehensively reveal the thermal runaway mechanism.A theoretical model of microcircuits and internal heat conduction is also established.The results indicated three thermal runaway evolution processes for high-capacity batteries,which corresponded to the experimental results of thermal equilibrium,single thermal runaway,and two thermal runaway events.The difference in heat distribution in the three phenomena is determined based on the microstructure and material structure near the pinhole.By controlling the heat dissipation conditions,the time interval between two thermal runaway events can be delayed from 558 to 1417 s,accompanied by a decrease in the concentration of in-situ gas production during the second thermal runaway event.

Control of microwave signals using bichromatic electromechanically induced transparency in multimode circuit electromechanical systems

We theoretically investigate the tunable delay and advancement of microwave signals based on bichromatic electromechanically induced transparency in a three-mode circuit electromechanical system, where two nanomechanical resonators with closely spaced frequencies are independently coupled to a common microwave cavity. In the presence of a strong microwave pump field, we obtain two transparency windows accompanied by steep phase dispersion in the transmitted microwave probe field. The width of the transparency window and the group delay of the probe field can be controlled effectively by the power of the pump field. It is shown that the maximum group delay of 0.12 ms and the advancement of0.27 ms can be obtained in the current experiments.

Chip Design of Li-Ion Battery Charger Operating in Constant-Current/Constant-Voltage Modes

A design for a Li-ion battery charger IC that can operate in a constant current-constant voltage （CC- CV） charge mode is proposed. In the CC-CV charge mode,the charger IC provides a constant charging current at the beginning, and then the charging current begins to decrease before the battery voltage reaches its final value. After the battery voltage reaches its final value and remains constant,the charging current is further reduced. This approach prevents charging the battery with full current near its saturated voltage,which can cause heating. The novel design of the core of the charger IC realizes the proposed CC-CV charge mode. The chip was implemented in a CSMC 0.6μm CMOS mixed signal process. The experimental results verify the realization of the proposed CC- CV charge mode. The voltage of the battery after charging is 4. 1833V.

Design and implementation of GM- APD array readout circuit for infrared imaging

Based on an avalanche photodiode（ APD） detecting array working in Geiger mode（ GM-APD）, a high-performance infrared sensor readout integrated circuit（ ROIC） used for infrared 3D（ three-dimensional） imaging is proposed. The system mainly consists of three functional modules, including active quenching circuit（ AQC）, time-to-digital converter（ TDC） circuit and other timing controller circuit. Each AQC and TDC circuit together constitutes the pixel circuit. Under the cooperation with other modules, the current signal generated by the GM-APD sensor is detected by the AQC, and the photon time-of-flight（ TOF） is measured and converted to a digital signal output to achieve a better noise suppression and a higher detection sensitivity by the TDC. The ROIC circuit is fabricated by the CSMC 0. 5 μm standard CMOS technology. The array size is 8 × 8, and the center distance of two adjacent cells is 100μm. The measurement results of the chip showthat the performance of the circuit is good, and the chip can achieve 1 ns time resolution with a 250 MHz reference clock, and the circuit can be used in the array structure of the infrared detection system or focal plane array（ FPA）.

Instantaneous Current Feedback Control Strategy on Buck Mode Inverter

Buck型逆变器的电感电流瞬时值反馈控制和电容电流瞬时值反馈控制存在本质区别。以差动正激直流斩波器型高频环节逆变器为例，采用理论推导方法，研究这两种电流控制逆变器的稳定性、输出外特性、短路能力、输出功率特性、带非线性负载能力及动态响应特性。研究结果表明，电感电流瞬时值反馈控制逆变器具有电感电流和输出功率受限、较强的过载和短路能力、较软的输出外特性、较弱的带非线性负载能力、较差的动态响应等特点；而电容电流瞬时值反馈控制逆变器具有电感电流和输出功率不受限、较弱的过载能力、无短路能力、硬的输出外特性、较强的带非线性负载能力、较好的动态响应等特点。研究成果为Buck型逆变器电流型控制策略的选择及其设计提供重要的理论依据。

Chaos synchronization of a chain network based on a sliding mode control

A sliding mode control approach is proposed to implement the synchronization of the chain tree network. The doublescroll circuit chaos systems are treated as nodes and the network is constructed with the state variable coupling. By selecting a switching sliding surface, the chaos synchronization of the network is achieved with one control input only. The stability analysis and the numerical simulations demonstrate that the complete synchronization in a chain network can be realized for all nodes.

Dynamic analysis and fractional-order adaptive sliding mode control for a novel fractional-order ferroresonance system

Ferroresonance is a complex nonlinear electrotechnical phenomenon, which can result in thermal and electrical stresses on the electric power system equipments due to the over voltages and over currents it generates. The prediction or determination of ferroresonance depends mainly on the accuracy of the model used. Fractional-order models are more accurate than the integer-order models. In this paper, a fractional-order ferroresonance model is proposed. The influence of the order on the dynamic behaviors of this fractional-order system under different parameters n and F is investigated. Compared with the integral-order ferroresonance system, small change of the order not only affects the dynamic behavior of the system, but also significantly affects the harmonic components of the system. Then the fractional-order ferroresonance system is implemented by nonlinear circuit emulator. Finally, a fractional-order adaptive sliding mode control （FASMC） method is used to eliminate the abnormal operation state of power system. Since the introduction of the fractional-order sliding mode surface and the adaptive factor, the robustness and disturbance rejection of the controlled system are en- hanced. Numerical simulation results demonstrate that the proposed FASMC controller works well for suppression of ferroresonance over voltage.

Voltage Mode Universal Filter Using Current Differencing Buffered Amplifier as an Active Device

Integrated filter circuit design resulted in desire for replacement of Inductors by active elements like Operational Amplifiers which led to the introduction of active filters. Active filter design has evolved over a period of time. Starting with OP AMPs, we have witnessed phenomenal growth of active component usage in filter design and development catering to varying requirements. This has contributed greatly in emergence of circuits with minimal limitations and advantages in terms of wide Bandwidth and High slew rates. Current Differencing Buffered Amplifier (CDBA) based active filter design has resulted in introduction of many novel circuits .This paper proposes a new Voltage-mode three input and Single output (TISO) multifunction filter based on single CDBA, four resistors and two capacitors. This second order filter circuit is capable of realizing various filter functions by choosing values of the three inputs variably. The natural frequency (ω0) can be tuned with passive components and the Q of the circuit is independent of (ω0) .The higher cascading capability of the circuit is ensured because of its low - output impedance. Further PSPICE-simulated results are in conformity with theoretical values.

Complete eigenmode analysis of a ladder-type multiple-gap resonant cavity

A theoretical model is developed for calculating the eigenmodes of the multi-gap resonant cavity. The structure of concern is a kind of ladder-type circuit, offering the advantages of easy fabrication, high characteristic impedance （R/Q）, and thermal capacity in the millimeter wave to THz regime. The eigenfunction expansion method is used to establish the field expressions for the gaps and the coupling region. Then, the match conditions at the interface are employed, which leads to a group of complicate boundary equations in the form of an infinite series. To facilitate the mathematical treatments and perform a highly efficient calculation, these boundary equations are transformed into the algebraic forms through the matrix representations. Finally, the concise dispersion equation is obtained. The roots of the dispersion equation include both the axial modes in the gaps, which include the fundamental and the high-order modes, and the cavity modes in the coupling region. Extensive numerical results are presented and the behaviors of the multi-gap resonant cavity are examined.