Microwave electrometry with Rydberg atoms in a vapor cell using microwave amplitude modulation

We have theoretically and experimentally studied the dispersive signal of the Rydberg atomic electromagneticallyinduced transparency(EIT)Autler–Townes(AT)splitting spectra obtained using amplitude modulation of the microwave(MW)electric field.In addition to the two zero-crossing points interval△f_(zeros),the dispersion signal has two positive maxima with an interval defined as the shoulder interval△f_(sho),which is theoretically expected to be used to measure a much weaker MW electric field.The relationship of the MW field strength E_(MW)and△f_(sho)is experimentally studied at the MW frequencies of 31.6 GHz and 9.2 GHz respectively.The results show that△f_(sho)can be used to characterize the much weaker E_(MW)than that of△f_(zeros)and the traditional EIT–AT splitting interval△f_(m);the minimum E_(MW)measured by△f_(sho)is about 30 times smaller than that by△f_(m).As an example,the minimum E_(MW)at 9.2 GHz that can be characterized by△f_(sho)is 0.056 mV/cm,which is the minimum value characterized by the frequency interval using a vapor cell without adding any auxiliary fields.The proposed method can improve the weak limit and sensitivity of E_(MW)measured by the spectral frequency interval,which is important in the direct measurement of weak E_(MW).

Amplitude modulation and extreme events in turbulent channel flow

Amplitude modulation of near-wall turbulence by large-scale structures in the outer layer is investigated by direct numerical simulation of turbulent channel flows at Reynolds number Re= 540, 1000, 2000. The effect of modulation is obvious in the two-point cross-section correlation map, and the correlation coefficients increase significantly with the Reynolds number. The influence of modulation is reflected in the tail of the probability density function of the near-wall flow signals, which expands as the Reynolds number increases. The flatness factor provides a quantitative description of the high fluctuation events due to modulation. Vortical structures associated with modulation are revealed by conditionally averaging the flow field of the near-wall extreme events, providing a depiction of how the influence of the large-scale structures penetrate towards the near-wall region.

Amplitude modulation measurement of symmetrical microwave power sensor

In order to reduce the mismatch error, a direct current （DC） calibration method is introduced when the modulated microwave signal is measured. The microwave power is input to the left section of the power sensor, and the DC power is input to the right of the power sensor. Due to the existence of parasitic loss and electromagnetic coupling, the microwave power results in a mismatch error. However, the DC power does not have the mismatch error. So the DC power applied in the right section can calibrate the mismatch error of the microwave power in the left section. The calibration factor is measured at different modulation rates and modulation depths.The measurement results show that the carrier frequency is the major factor influencing the measurement results. After calibration, the carrier frequency and the modulation rate have little effect on the output voltage. The frequency response becomes relatively flat in the frequency range up to 20 GHz, and the sensitivity on average is enhanced by about 0.12 mV/dBm. Therefore, the DC calibration method has a certain reference value for the terminal-type microwave power sensor.

Stochastic Resonance in a Single-Mode Laser Driven by Quadratic Colored Pump Noise:Effects of Biased Amplitude Modulation Signal

A single-mode laser noise model driven by quadratic colored pump noise and biased amplitude modulationsignal is proposed.The analytic expression of signal-to-noise ratio is calculated by using a new linearized procedure.Itis found that there are three different typies of stochastic resonance in the model:the conventional form of stochasticresonance,the stochastic resonance in the broad sense,and the bona fide SR.

Noise amplitude modulation jamming signal suppression based on weighted-matching pursuit

To suppress noise amplitude modulation jamming in a single-antenna radar system, a new method based on weighted-matching pursuit （WMP） algorithm is proposed, which can achieve underdetermined blind sources separation of the jamming and the target echo from the jammed mixture in the single channel of the receiver. Firstly, the presented method utilizes a prior information about the differences between the jamming component and the radar transmitted signal to construct two signal-adapted sub-dictionaries and to determine the weights. Then the WMP algorithm is applied to remove the jamming component from the mixture. Experimental results verify the validity of the presented method. By comparison of the pulse compression performance, the simulation results shows that the presented method is superior to the method of frequency domain cancellation （FDC） when the jamming-to-signal ratio （JSR） is lower than 15 dB.

An all-optical phase detector by amplitude modulation of the local field in a Rydberg atom-based mixer

Recently,a Rydberg atom-based mixer was developed to measure the phase of a radio frequency(RF)field.The phase of the signal RF(SIG RF)field is down-converted directly to the phase of a beat signal created by the presence of a local RF(LO RF)field.In this study,we propose that the Rydberg atom-based mixer can be converted to an all-optical phase detector by amplitude modulation(AM)of the LO RF field;that is,the phase of the SIG RF field is related to both the amplitude and phase of the beat signal.When the AM frequency of the LO RF field is the same as the frequency of the beat signal,the beat signal will further interfere with the AM of the LO RF field inside the atom,and then the amplitude of the beat signal is related to the phase of the SIG RF field.The amplitude of the beat signal and the phase of the SIG RF field show a linear relationship within the range of 0 toπ/2 when the phase of the AM is set with a differenceπ/4 from the phase of the LO RF field.The minimum phase resolution can be as small as 0.6°by optimizing the experimental conditions according to a simple theoretical model.This study will expand and contribute to the development of RF measurement devices based on Rydberg atoms.

A new tracking error detection method using amplitude difference detection for signal waveform modulation multi-level discs

The sub-land/sub-pit affects the characteristic of the tracking error signal which is generated by the conventional differential phase detection （DPD） method in the signal waveform modulation multi-level （SWML） read-only disc. To solve this problem, this paper proposes a new tracking error detection method using amplitude difference. Based on the diffraction theory, the amplitude difference is proportional to the tracking error and is feasible to be used for obtaining the off-track information. The experimental system of the amplitude difference detection method is developed. The experimental results show that the tracking error signal derived from the new method has better performance in uniformity and signal-to-noise ratio than that derived from the conventional DPD method in the SWML read-only disc.

Semi-blind Adaptive Beamforming for High-throughput Quadrature Amplitude Modulation Systems

A semi-blind adaptive beamforming scheme is proposed for wireless systems that employ high-throughput quadrature amplitude modulation signalling. A minimum number of training symbols, equal to the number of receiver antenna arrayts elements, are first utilised to provide a rough initial least squares estimate of the beamformer＇s weight vector. A concurrent constant modulus algorithm and soft decision-directed scheme is then applied to adapt the beamformer. This semi-blind adaptive beamforming scheme is capable of converging fast to the minimum mean-square-error beamforming solution, as demonstrated in our simulation study.

Stochastic Resonance in Linear Region of a Single-Mode Laser: Effects of Amplitude Modulation of Signal

A single-mode laser noise model driven by quadratic colored pump noise and amplitude modulation signal is proposed. The real and imaginary parts of the pump noise are assumed to be cross-correlation. The effect of cross- correlation of noise and amplitude modulation of signal on laser statistical properties is studied by using the linearized approximation. The analytic expression of signal-to-noise ratio （SNR） is calculated. It is found that the phenomena of stochastic resonance （SR） respectively exist in the curves of the SNR versus the noise cross-correlation coefficient λ and the SNR versus the pump parameter a, as well as the SNR versus the signal frequency ω in our model. It is shown that there are three different typies of SR in the model： the conventional form of SR, the SR in the broad sense, and the bona fide SR.

A 3-D Polarization Quadrature Amplitude Modulation Method and Constellation Mapping

As a new three-dimensional(3-D)modulation,Polarization Quadrature Amplitude Modulation(PQAM) can be regarded as the combination of Pulse amplitude modulation(PAM) and Quadrature Amplitude Modulation(QAM) Modulation.It can better improve the digital communication efficiency and reduce the Symbol error rate(SER) of the system than one-dimensional or two-dimensional modulation scheme.How to design a feasible constellation is the most concerned problem of PQAM currently.This paper first studies the relationship between the SER theoretical value of PQAM and the distribution of M and N,proposes a new M,N allocation scheme.Secondly,a new and straightforward design method of constructing higher-level 3-D signal constellations,which can be matched with the PQAM,and the constellation can divided into three different structures according to the ary for PQAM.Finally,the simulation results show that:in PQAM system,the modulation scheme and the constellation mapping scheme are proposed in this paper which can effectively reduce the system SER and improve the anti-noise performance of the system.

Close-Loop Bell-Bloom Magnetometer with Amplitude Modulation

A high sensitive optical amplitude modulation magnetometer is investigated and demonstrated experimentally. We build an experimental platform for the atomic magnetometer and configure it as a Bell-Bloom magnetometer with amplitude modulation of 50% duty cycle square waveform. The open-loop input-output model is deduced from the Bloch equation and is verified experimentally. Instead of locking the frequency by using a voltage control oscillator, we realize a closed loop using the coils to generate a feedback field which avoids the stringent require- ment of a high resolution frequency meter and markedly expands the dynamic range as well as the bandwidth. We realize an open loop sensitivity of 0.8pT/Hz1/2 at 20 Hz using a single light beam, which exceeds that of the state-of-the-art Bell-Bloom magnetometers, and the corresponding closed loop sensitivity is 1.2 pT/Hz1/2.

Amplitude modulation excitation for cancellous bone evaluation using a portable ultrasonic backscatter instrumentation

The ultrasonic backscatter(UB)has the advantage of non-invasively obtaining bone density and structure,expected to be an assessment tool for early diagnosis osteoporosis.All former UB measurements were based on exciting a short single-pulse and analyzing the ultrasonic signals backscattered in bone.This study aims to examine amplitude modulation(AM)ultrasonic excitation with UB measurements for predicting bone characteristics.The AM multiple lengths excitation and backscatter measurement(AM-UB)functions were integrated into a portable ultrasonic instrument for bone characterization.The apparent integrated backscatter coefficient in the AM excitation(AIB_(AM))was evaluated on the AM-UB instrumentation.The correlation coefficients of the AIB_(AM) estimating volume fraction(BV/TV),structure model index(SMI),and bone mineral density(BMD)were then analyzed.Significant correlations(|R|=0.82-0.93,p<0.05)were observed between the AIB_(AM),BV/TV,SMI,and BMD.By growing the AM excitation length,the AIB_(AM) values exhibit more stability both in 1.0-MHz and 3.5-MHz measurements.The recommendations in AM-UB measurement were that the avoided length(T1)should be lower than AM excitation length,and the analysis length(T2)should be enough long but not more than AM excitation length.The authors conducted an AM-UB measurement for cancellous bone characterization.Increasing the AM excitation length could substantially enhance AIB_(AM) values stability with varying analyzed signals.The study suggests the portable AM-UB instrument with the integration of real-time analytics software that might provide a potential tool for osteoporosis early screening.

Effect of Hot Carrier on Amplitude Modulation and Demodulation of Gaussian High Power Helicon Wave in Homogeneous Longitudinally Magnetized Strain Dependent Dielectric Material

In the present communication, the hydrodynamic model is used to investigate the amplitude modulation as well as demodulation of an electromagnetic wave of high power helicon pump wave into another helicon wave in strain dependent dielectric material incorporating carrier heating (CH) effects. The consideration of CH in modulation and demodulation is prime importance for the adding of new dimension in analysis of amplification of acoustic helicon wave. By using the dispersion relation, threshold pump electric filed and growth rate of unstable mode from the modulation and demodulation of the high power helicon wave well above from the threshold value will be discussed in the present analysis. The numerical analysis is applied to a strain dependent dielectric material, BaTiO3 at room temperature and irradiated with high power helicon wave of frequency 1.78 × 1014 Hz. This material is very sensitive to the pump intensities, therefore during studies, Gaussian shape of the helicon pump wave is considered during the propagation in stain dependent dielectric material and opto-acoustic wave in the form of Gaussian profile (ω0,κ0) is induced longitudinally along the crystallographic plane of BaTiO3. Its variation is caused by the available magnetic field (ωc), interaction length (z) and pulsed duration of interaction (τ). From the analysis of numerical results, the incorporation of CH effect can effectively modify the magnitude of modulation or demodulation of the amplitude of high power helicon laser wave through diffusion process. Not only the amplitude modulation and demodulation of the wave, the diffusion of the CH effectively modifies the growth rate of unstable mode of frequency in BaTiO3. The propagation of the threshold electric field shows the sinusoidal or complete Gaussian profile, whereas this profile is found to be completely lost in growth of unstable mode. It has also been seen that the growth rate is observed to be of the order of 108 - 1010 s-1 but from diffusion of carrier heating, and that its order is enhanced from 1010 - 1012 s-1 with the variation of the magnetized frequency from 1 to 2.5 × 1014 Hz.

Transfer characteristics of dynamic biochemical signals in non-reversing pulsatile flows in a shallow Y-shaped microfluidic channel: signal filtering and nonlinear amplitude-frequency modulation

The transports of the dynamic biochemical signals in the non-reversing pulsatile flows in the mixing microchannel of a Y-shaped microfluidic device are ana- lyzed. The results show that the mixing micro-channel acts as a low-pass filter, and the biochemical signals are nonlinearly modulated by the pulsatile flows, which depend on the biochemical signal frequency, the flow signal frequency, and the biochemical signal transporting distance. It is concluded that, the transfer characteristics of the dynamic biochemical signals, which are transported in the time-varying flows, should be carefully considered for better loading biochemical signals on the cells cultured on the bottom of the microfluidic channel.

Targeted treatment of cancer with radiofrequency electromagnetic fields amplitude-modulated at tumor-specific frequencies

In the past century, there have been many attempts to treat cancer with low levels of electric and magnetic fields. We have developed noninvasive biofeedback examination devices and techniques and discovered that patients with the same tumor type exhibit biofeedback responses to the same, precise frequencies. Intrabuccal administration of 27.12 MHz radiofrequency(RF) electromagnetic fields(EMF), which are amplitude-modulated at tumor-specific frequencies, results in long-term objective responses in patients with cancer and is not associated with any significant adverse effects. Intrabuccal administration allows for therapeutic delivery of very low and safe levels of EMF throughout the body as exemplified by responses observed in the femur, liver, adrenal glands, and lungs. In vitro studies have demonstrated that tumor-specific frequencies identified in patients with various forms of cancer are capable of blocking the growth of tumor cells in a tissue- and tumor-specific fashion. Current experimental evidence suggests that tumor-specific modulation frequencies regulate the expression of genes involved in migration and invasion and disrupt the mitotic spindle. This novel targeted treatment approach is emerging as an appealing therapeutic option for patients with advanced cancer given its excellent tolerability. Dissection of the molecular mechanisms accounting for the anti-cancer effects of tumor-specific modulation frequencies is likely to lead to the discovery of novel pathways in cancer.

Numerical simulation of jet breakup due to amplitude-modulated (A-M) disturbance

In order to characterize the mechanics of jet breakup, the finite volume formulations were employed to solve the Navier-Stokes equations and continuity equation of jet. The volume of fluid(VOF) method was used to track the free surface of jet. The spray process of the molten Pb63Sn37 alloy was simulated based on the mathematical model by means of FLUENT code. The configuration of jets generated in different disturbance ratios and modulation ratios was obtained. The theoretical results show that the droplets merge together by the number of disturbance ratio N, which agrees with the corresponding picture captured in the experiment. In addition, the droplet streams broken at non-optimal frequency are also uniform according to simulation results, which proves that the A-M disturbance can increase the width of the uniform droplet generating frequency.

Optimized analysis of ionospheric amplitude modulated heating parameters for excitation of very/extremely low frequency radiations

It is now well known that amplitude modulated(AM) high frequency(HF) radio wave transmissions into the ionosphere can be used to generate very/extremely low frequency(VLF/ELF) radio waves using the so-called ‘electrojet antenna’. Duty cycle and heating frequency are analyzed and discussed with the lower-ionosphere modulated heating model, so as to improve the radiation efficiency of VLF/ELF waves in AM ionospheric heating experiments. Based on numerical simulation, the ranges of parametric selectivity in optimal duty cycle and heating frequency( fHF) are derived. The International Reference Ionosphere 2015(IRI-2015) model and two-parameter model are used to predict background electron density profiles, and optimized ranges of duty cycle for different density profiles are analyzed and compared. The influences of wave polarizations on optimal duty cycle are also discussed. It is shown that intensity of the VLF/ELF equivalent radiation source(M) firstly rises and then falls with the increase of duty cycle. When using the IRI model, M peaks at a duty cycle of 50%, optimally ranging from 40%-70%. For the two-parameter model case, an optimal duty cycle is 40% and the optimized ranges vary from 30%-60%. Heating with an X-mode polarization is more efficient than with the O-mode case in VLF/ELF wave generation. Nevertheless, an optimal duty cycle is almost independent of HF wave polarizations. To obtain better VLF/ELF generation, optional fHFmay be 0.8-0.9 times of foE for the O-mode heating and 0.75-0.85 times for the X-mode polarization case. Finally, the variations of these two parameters in different latitudes are discussed.

A high-contrast imaging coronagraph for segmented-mirror large aperture telescopes using a spatial light modulator

The primary mirrors of current and future large telescopes always employ a segmented mirror configuration.The small but non-negligible gaps between neighboring segments cause additional diffraction,which restricts the performance of high-contrast coronagraph.To solve this problem,we propose a coronagraph system based on a single liquid crystal spatial light modulator(SLM).This spatial light modulator is used for amplitude apodization,and its feasibility and potential performance are demonstrated using a laboratory setup using the stochastic parallel gradient descent(SPGD)algorithm to control the spatial light modulator,which is based on point spread function(PSF)sensing and evaluation and optimized for maximum contrast in the discovery working area as a merit function.The system delivers a contrast in the order of 10−6,and shows excellent potential to be used in current and future large aperture telescopes,both on the ground and in space.

A GHz chirped amplitude-modulated laser for high-contrast plasma gratings

The generation and control of large amplitude plasma gratings and other plasma structures is of paramount importance for the realization of plasma photonics. Autoresonant excitation of such structures by means of chirped amplitude-modulated lasers has been recently discussed and analyzed theoretically. Here we discuss the parameter space for the realization of such a scheme and describe the laser system that was built towards this goal. We also expand our earlier theoretical study to account for the more realistic case of a moderately focused laser beam, instead of the simplified plane wave approximation.