期刊文献+
共找到231篇文章
< 1 2 12 >
每页显示 20 50 100
Collector optimization for tradeoff between breakdown voltage and cut-off frequency in SiGe HBT 被引量:1
1
作者 付强 张万荣 +3 位作者 金冬月 丁春宝 赵彦晓 鲁东 《Chinese Physics B》 SCIE EI CAS CSCD 2014年第11期354-358,共5页
As is well known, there exists a tradeoff between the breakdown voltage BVcEO and the cut-off frequency fT for a standard heterojunction bipolar transistor (HBT). In this paper, this tradeoff is alleviated by collec... As is well known, there exists a tradeoff between the breakdown voltage BVcEO and the cut-off frequency fT for a standard heterojunction bipolar transistor (HBT). In this paper, this tradeoff is alleviated by collector doping engineering in the SiGe HBT by utilizing a novel composite of P+ and N- doping layers inside the collector-base (CB) space-charge region (SCR). Compared with the single N-type collector, the introduction of the thin P+ layers provides a reverse electric field weakening the electric field near the CB metallurgical junction without changing the field direction, and the thin N layer further effectively lowers the electric field near the CB metallurgical junction. As a result, the electron temperature near the CB metallurgical junction is lowered, consequently suppressing the impact ionization, thus BVcEO is improved with a slight degradation in fT. The results show that the product of fTXBVcEo is improved from 309.51 GHz.V to 326.35 GHz.V. 展开更多
关键词 SiGe heterojunction bipolar transistors (HBTs) breakdown voltage cut-off frequency collectoroptimization
下载PDF
Over Voltage Fault due to Disconnection of Consumer’s Transformer Neutral Wire
2
作者 Erdene Adiyasuren Enkh-Od Erdene +1 位作者 Sergelen Byambaa Shagdarsuren Gantumur 《Journal of Energy and Power Engineering》 2023年第1期11-14,共4页
Practically,the load currents in three phases are asymmetric in the power system.It means that the impedances are different in all three phases.If the consumer’s transformer neutral cut off and/or was disconnected fr... Practically,the load currents in three phases are asymmetric in the power system.It means that the impedances are different in all three phases.If the consumer’s transformer neutral cut off and/or was disconnected from the neutral of power supply source,then there will be some trouble and failure occurred.The current in the neutral wire drops down to zero when the neutral wire is cut off and the phase currents of all three-phase equal to each other since there was no return wire.The currents are equal but the voltages at the phase consumers are different.Especially for residential single-phase consumers,the voltage at the consumers of the phase varies differently for three phase systems when the neutral wire was disconnected at consumer side and even the voltage at the consumers one or two of those three phases becomes over nominal voltage or reaches nearly line voltage.In this case,the electronic appliances in that phase will be fed by high voltage than the rated value and they can be broken down.In the power system of UB(Ulaanbaatar)city,there are some occasional such kind of failures every year.Obviously,many electronic appliances were broken down due to high voltage and the electricity utility companies respond for service charge of damaged parts. 展开更多
关键词 Neutral connection and neutral wire phase and line voltage single-phase residential consumer transformer neutral cut off asymmetric load current protective earth
下载PDF
The transverse laser induced thermoelectric voltages in step flow growth (1-x)Pb(Mg_(1/3)Nb_(2/3))O_(3-x)PbTiO_3 thin films
3
作者 尚杰 张辉 +2 位作者 李勇 曹明刚 张鹏翔 《Chinese Physics B》 SCIE EI CAS CSCD 2010年第10期452-457,共6页
This paper reports that the transverse laser induced thermoelectric voltages (LITV) axe observed for the first time in the step flow growth (1- x)PD(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT, x = 0.20, 0.33, 0.50) thin fi... This paper reports that the transverse laser induced thermoelectric voltages (LITV) axe observed for the first time in the step flow growth (1- x)PD(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT, x = 0.20, 0.33, 0.50) thin films deposited on vicinal-cut strontium titanate single crystal substrates. Because lead magnesium niobate-lead titanate is a solid solution of lead magnesium niobate (PMN) and lead titanate (PT), there are two types of signals. One is wide with a time response of a microsecond, and the other superimposed with the wide signal is narrow with a time response of a nanosecond. The transverse LITV signals depend on the ratio of PMN to PT drastically. Under the irradiation of 28-ns pulsed KrF excimer laser with the 248-nm wavelength, the largest induced voltage is observed in the 0.50Pb(Mg1/3Nb2/3)O3-0.50 PbTiO3 films. Moreover, the effects of film thickness, substrates, and tilt angles of substrates are also investigated. 展开更多
关键词 laser induced thermoelectric voltage (1- x)PD(Mg1/3Nb2/3)O3-xPbTiO3 films anisotropic Seebeck effect
下载PDF
Layer regrouping for water-flooded commingled reservoirs at a high water-cut stage 被引量:2
4
作者 Chuan-Zhi Cui Jian-Peng Xu +3 位作者 Duan-Ping Wang Zhi-Hong Liu Ying-song Huang Zheng-Ling Geng 《Petroleum Science》 SCIE CAS CSCD 2016年第2期272-279,共8页
Layer regrouping is to divide all the layers into several sets of production series according to the physical properties and recovery percent of layers at high water-cut stage, which is an important technique to impro... Layer regrouping is to divide all the layers into several sets of production series according to the physical properties and recovery percent of layers at high water-cut stage, which is an important technique to improve oil recovery for high water-cut multilayered reservoirs. Dif- ferent regroup scenarios may lead to different production performances. Based on unstable oil-water flow theory, a multilayer commingled reservoir simulator is established by modifying the production split method. Taking into account the differences of layer properties, including per- meability, oil viscosity, and remaining oil saturation, the pseudo flow resistance contrast is proposed to serve as a characteristic index of layer regrouping for high water-cut multilayered reservoirs. The production indices of multi- layered reservoirs with different pseudo flow resistances are predicted with the established model in which the data are taken from the Shengtuo Oilfield. Simulation results show that the pseudo flow resistance contrast should be less than 4 when the layer regrouping is implemented. The K-means clustering method, which is based on the objec- tive function, is used to automatically carry out the layer regrouping process according to pseudo flow resistances. The research result is applied to the IV-VI sand groups of the second member of the Shahejie Formation in the Shengtuo Oilfield, a favorable development performance is obtained, and the oil recovery is enhanced by 6.08 %. 展开更多
关键词 Water-flooded reservoirs Layer regrouping.Flow resistance - High water cut Reservoir simulation
下载PDF
Preliminary Study on Water Demand Law of 1-0 Rooted Cuttings of Populus szechuanica
5
作者 Dabuqiong Haoyu WANG +2 位作者 Huanhuan XIE Zhen XING Yanhui YE 《Meteorological and Environmental Research》 CAS 2021年第4期39-42,共4页
In order to provide theoretical basis and technical support for the afforestation and artificial water supply of P.szechuanica in arid areas,the characteristics of water consumption of P.szechuanica were explored,and ... In order to provide theoretical basis and technical support for the afforestation and artificial water supply of P.szechuanica in arid areas,the characteristics of water consumption of P.szechuanica were explored,and the law of water demand of P.szechuanica was grasped.In this paper,potted seedlings of 1-0 rooted cuttings of P.szechuanica were taken as research objects,and change situation of water consumption under different water control gradients was measured regularly by using weighing method,further analyzing dynamic change of water consumption of P.szechuanica and revealing water demand law of 1-0 rooted cuttings of P.szechuanica.The results showed that total change of water consumption of 1-0 rooted cuttings of P.szechuanica had"slow-fast-slow-fast"double-peak trend in the growth period of the current year,and corresponded with univariate linear relation(R^(2)=0.7137),with significant difference.In whole growth period,water consumption in August was the highest,which was 2.7 times of that in June and July and 1.5 times of that after September.In different water control treatments,the dynamic changes of daily and monthly water consumption were significantly different.In seven water control treatments,monthly water consumption was between(6315.95±1690.70)and(10105.28±3065.30)g/month,and mean was(8211.07±2308.23)g/month.With intensification of water control treatment,water consumption increased,but there was no seedling death due to water shortage.P.szechuanica has great plasticity in water demand,and can survive in both arid and humid environments.Meanwhile,it is revealed that P.szechuanica is the most widely distributed tree species in the region. 展开更多
关键词 Populus szechuanica 1-0 rooted cuttings Water consumption Water demand law
下载PDF
基于Normalized Cut的图像分割改进算法 被引量:11
6
作者 黄一岑 沈一帆 《计算机工程与应用》 CSCD 北大核心 2008年第34期179-181,187,共4页
用Normalized Cu(tN-Cut)准则分割图片时,会出现诸如过分割或者欠分割的不理想情况。在N-Cut结果的基础上提出了一种改进算法:利用合并-分裂方法,将颜色和纹理相似的区域合并,并对某些区域做进一步N-Cut分割。实验证明,改进后的算法不... 用Normalized Cu(tN-Cut)准则分割图片时,会出现诸如过分割或者欠分割的不理想情况。在N-Cut结果的基础上提出了一种改进算法:利用合并-分裂方法,将颜色和纹理相似的区域合并,并对某些区域做进一步N-Cut分割。实验证明,改进后的算法不仅保留了N-Cut方法的优点,而且从一定程度上解决了过分割和欠分割的缺点,能够处理一些自然界的彩色图片,得到了比较理想的分割结果。 展开更多
关键词 合并-分裂 N—cut准则 Texton
下载PDF
高性能涂层刀具切削GH4169高温合金的切削性能研究
7
作者 徐兴伟 李良成 +4 位作者 伍爱江 陈诚 崔俊博 熊计 刘俊波 《工具技术》 北大核心 2024年第5期47-52,共6页
针对难加工材料GH4169镍基高温合金切削问题,制备了TiAlN/TiAlSiN复合涂层切削刀具,主要研究了不同偏压下TiAlN/TiAlSiN复合涂层刀具的涂层显微组织、力学性能以及切削GH4169镍基高温合金时的切削性能。结果表明:偏压和涂层厚度增加,涂... 针对难加工材料GH4169镍基高温合金切削问题,制备了TiAlN/TiAlSiN复合涂层切削刀具,主要研究了不同偏压下TiAlN/TiAlSiN复合涂层刀具的涂层显微组织、力学性能以及切削GH4169镍基高温合金时的切削性能。结果表明:偏压和涂层厚度增加,涂层柱状晶趋势明显,表面孔隙减少,涂层致密性提高;偏压增加,复合涂层与基体结合力增加,并且在偏压为-100V时,结合力达到最大值74.3N。涂层的硬度和弹性模量也随着偏压的增加而增大;切削GH4169高温合金时,涂层刀具的切削磨损量明显小于未涂层刀具,且随着偏压的增加,涂层刀具的寿命得到提高;当偏压为-100V时,切削寿命最高,这归因于切削过程中Ni, Cr, Al等元素氧化并在表面形成一层致密且具有一定润滑特性的保护膜。 展开更多
关键词 涂层 偏压 刀具 高温合金
下载PDF
微过充下三元镍钴铝锂离子电池的老化机理
8
作者 王岩松 陈顺 +1 位作者 范国栋 张希 《电池》 CAS 北大核心 2024年第2期154-159,共6页
电芯的不一致性及电量不均衡,会导致部分锂离子电池单体出现微过充现象,但此情况对于电池容量的影响未被完全揭示。在不同最高截止电压(4.2 V、4.3 V和4.4 V)下对三元镍钴铝(Li_(x)Ni_(0.80)Co_(0.15)Al_(0.05)O_(2))电池进行恒流充电... 电芯的不一致性及电量不均衡,会导致部分锂离子电池单体出现微过充现象,但此情况对于电池容量的影响未被完全揭示。在不同最高截止电压(4.2 V、4.3 V和4.4 V)下对三元镍钴铝(Li_(x)Ni_(0.80)Co_(0.15)Al_(0.05)O_(2))电池进行恒流充电循环老化实验,采用差分电压分析、电化学阻抗谱(EIS)等测试方法,探究高截止电压循环对电池老化的影响。随着最高截止电压的升高,电池老化速度加快,以2.5 A电流循环280次后,4.2 V、4.3 V、4.4 V下的容量保持率分别为90.30%、88.19%和86.19%。差分电压分析表明,容量衰减加速的原因是正极活性物质损失和活性Li+损失。EIS测试表明,微过充导致固体电解质相界面(SEI)膜阻抗略微升高,电荷转移阻抗升高,且程度随截止电压的升高而增大。 展开更多
关键词 锂离子电池 镍钴铝(Li_(x)Ni_(0.80)Co_(0.15)Al_(0.05)O_(2)) 微过充 高截止电压 老化模式 活性物质损失 电荷转移阻抗
下载PDF
提升末端区域电网供电能力的调控方案及稳控策略研究
9
作者 刘昭睿 王凯 +2 位作者 王新建 郭琪 范卓 《内蒙古电力技术》 2024年第3期52-60,共9页
针对内蒙古某末端区域电网供电能力受同塔双回线路N-2故障及母线故障制约问题,开展安全稳定控制系统(以下简称稳控系统)控制策略研究。首先,基于对典型故障后末端区域电网稳定特性的仿真计算与分析,结合新能源出力、火电机组开机等对切... 针对内蒙古某末端区域电网供电能力受同塔双回线路N-2故障及母线故障制约问题,开展安全稳定控制系统(以下简称稳控系统)控制策略研究。首先,基于对典型故障后末端区域电网稳定特性的仿真计算与分析,结合新能源出力、火电机组开机等对切负荷定值的影响,制订预控方案与稳控系统相结合的综合调度控制方案;然后,分析电解铝行业整流变压器负荷转移特性,提出可优先实切负荷量计算方法和适用于末端电网的分档阶梯切负荷原则,对末端区域电网稳控系统的控制策略进行优化。 展开更多
关键词 供电能力 安全稳定控制系统 切负荷 电压稳定 暂态稳定
下载PDF
计及临界稳定特性的感应电动机群等值方法
10
作者 李涛 黄淼 吴启飞 《大电机技术》 2024年第3期1-7,共7页
为降低感应电动机临界稳定特性对感应电动机群等值的影响,提高感应电动机群等值模型的准确性和适用性,本文提出一种计及安全临界电压和临界切除时间的感应电动机群等值方法。首先,分析表征感应电动机临界稳定特性强弱的指标,结合聚类分... 为降低感应电动机临界稳定特性对感应电动机群等值的影响,提高感应电动机群等值模型的准确性和适用性,本文提出一种计及安全临界电压和临界切除时间的感应电动机群等值方法。首先,分析表征感应电动机临界稳定特性强弱的指标,结合聚类分析算法,将感应电动机群分为稳定性不同的3组。其次,依据感应电动机群等值的基本原则,求解等值感应电动机电气参数。最后,以IEEE-9节点系统为算例,比较通过本文方法和现有方法得到的等值模型在不同故障下的系统响应。仿真结果表明,本文方法得到的等值模型能更好地还原原感应电动机群的工作特征。 展开更多
关键词 感应电动机 安全临界电压 临界切除时间 聚类分析 动态聚合
下载PDF
电化学放电线切割电压-电流特性研究 被引量:1
11
作者 李其 蒋毅 +2 位作者 孔令蕾 赵万生 平雪良 《电加工与模具》 2015年第6期15-19,共5页
设计并搭建了基于水平走丝方式的电化学放电线切割加工装置,可用于非导电硬脆材料的微细线切割加工,研究了加工过程中的电压电流特性。当电压超过临界值后,电极丝表面会形成不稳定的气层并产生放电现象;随着电压升高,放电状态由火花放... 设计并搭建了基于水平走丝方式的电化学放电线切割加工装置,可用于非导电硬脆材料的微细线切割加工,研究了加工过程中的电压电流特性。当电压超过临界值后,电极丝表面会形成不稳定的气层并产生放电现象;随着电压升高,放电状态由火花放电向电弧放电过渡。对石英玻璃的加工实验结果显示,通过增加电压并使放电电压维持在火花区内,能在保证表面质量较好的同时提高加工效率,在电弧区加工可得到更高的材料去除率,但工件表面质量会下降。 展开更多
关键词 微细加工 水平走丝 电化学放电线切割 电压-电流特性
下载PDF
基于M-BUS的矿用超声波明渠流量计设计 被引量:1
12
作者 徐乐年 刘伟光 王全 《煤矿机电》 2011年第4期43-46,50,共5页
为实时监控明渠流量,有效预防矿井水害的发生,采用无喉道槽和非接触测量的超声波智能流量传感器测量明渠流量,既给出了明渠实时流量与水头高度之间的关系,减少了淤积的泥沙对测量的影响,又提高了流量测量装置的稳定性。实验表明,超声波... 为实时监控明渠流量,有效预防矿井水害的发生,采用无喉道槽和非接触测量的超声波智能流量传感器测量明渠流量,既给出了明渠实时流量与水头高度之间的关系,减少了淤积的泥沙对测量的影响,又提高了流量测量装置的稳定性。实验表明,超声波无喉道槽流量计的不确定度低于4%,符合国家的相关标准。 展开更多
关键词 明渠流量计 无喉道槽 超声波智能流量传感器 动态电压阈值
下载PDF
AC-LED结温与开启电压关系测量
13
作者 张大伟 许键 《光学仪器》 2014年第1期1-5,共5页
根据交流发光二极管(AC-LED)的工作特征,提出了一种简单而精准的AC-LED结温测量方法:开启电压法。通过理论分析和实验发现,AC-LED的开启电压会随着结温的上升而下降,且两者之间有良好的线性关系,从而确认将开启电压作为温度变化参数来... 根据交流发光二极管(AC-LED)的工作特征,提出了一种简单而精准的AC-LED结温测量方法:开启电压法。通过理论分析和实验发现,AC-LED的开启电压会随着结温的上升而下降,且两者之间有良好的线性关系,从而确认将开启电压作为温度变化参数来间接测量AC-LED的结温。实验表明,开启电压法测量结温的重复性最大误差为2.0℃,热阻重复性最大误差为0.6℃/W。经过对比分析,开启电压法得到热阻值比参考脉冲法更接近真实值。 展开更多
关键词 AC-LED 结温 测量方法 开启电压法
下载PDF
Enhanced piezoresistivity in Ni-silicone rubber composites 被引量:1
14
作者 常方高 杨枫 +2 位作者 王少祥 张娜 宋桂林 《Chinese Physics B》 SCIE EI CAS CSCD 2009年第2期652-657,共6页
This paper reports that the nickel-silicone rubber composites with enhanced piezoresistivity were synthesized with much reduced nickel concentration. A large piezosensitivity of 0.716/kPa and a gauge factor of 600 hav... This paper reports that the nickel-silicone rubber composites with enhanced piezoresistivity were synthesized with much reduced nickel concentration. A large piezosensitivity of 0.716/kPa and a gauge factor of 600 have been obtained for a composite sample with filler-polymer ratio of 2.7:1 by weight. Measurements of resistance as a function of uniaxial force reveal that the piezoresistance arises predominantly from the internal heterogeneity of the material and the effect of geometrical changes of samples under pressure is negleetably small. The nonlinear current-voltage characteristic of the composite depends strongly on the filler content, the initial compression and the electrical current flowing in the sample. Ohmic behaviour has been observed only in the highly compressed samples. The breakdown strength decreases with increasing filler content of the composite. Both I - V and R - f characteristics indicates that the resistivity of the composites decreases with electrical field, suggesting that the composite may also be used to make voltage sensitive resistors for protecting circuits. All the experimental results favour a quantum tunnelling mechanism of conductivity. It finds that the concept 'negative resistance', often used to describe the phenomena that current decreases with increasing voltage, is not appropriate and should be avoided. 展开更多
关键词 PIEZORESISTIVITY quantum tunnelling I - V characteristics voltage sensitive resistors
下载PDF
CUT201超声仪在工程应用的实例分析
15
作者 赵洪波 崔岩 《交通世界》 2004年第4期39-41,共3页
我院自2000年购进了CUT201型超声仪以后,除了在教学中得以应用,还积极参加了工程实践活动。
关键词 cut201超声仪 混凝土测量 道路工程 回弹-超声综合法 测量精度 强度测量
下载PDF
GB/T 15576-2008涌流试验影响因素分析及对策研究
16
作者 信天 李洪亮 +2 位作者 窦慧 王鑫 张超 《环境技术》 2021年第2期225-231,共7页
针对低压成套无功功率补偿装置型式试验中的涌流在实际检测过程中由于检验要求不明确,导致试验数据受其他因素影响较大的问题,该文以GB/T 15576-2008为基础,采用标准比对、仿真与实际试验论证相结合的方法,研究短路容量、投切角度、电... 针对低压成套无功功率补偿装置型式试验中的涌流在实际检测过程中由于检验要求不明确,导致试验数据受其他因素影响较大的问题,该文以GB/T 15576-2008为基础,采用标准比对、仿真与实际试验论证相结合的方法,研究短路容量、投切角度、电容残压对涌流值的影响。研究结果建议以装置的短路耐受强度认证申请值作为额定试验系统短路容量,以85°〜90°作为峰值投入的投切角度区间,最后一组投入的电容器残压值尽可能小或两次投入时间间隔应至少保证3 min以上,作为各第三方检测机构的规范统一的检验要求。研究结论完善了涌流试验的检验技术要求和检测方法,可为涌流型式试验提供重要的技术参考和标准依据。 展开更多
关键词 低压成套无功功率补偿装置 涌流 短路容量 投切角度 电容残压
下载PDF
0.15-μm T-gate In_(0.52)Al_(0.48)As/In_(0.53)Ga_(0.47)As InP-based HEMT with fmax of 390 GHz
17
作者 钟英辉 张玉明 +4 位作者 张义门 王显泰 吕红亮 刘新宇 金智 《Chinese Physics B》 SCIE EI CAS CSCD 2013年第12期522-526,共5页
In this paper, 0.15-μm gate-length In0.52Al0.48As/In0.53Ga0.47As InP-based high electron mobility transistors (HEMTs) each with a gate-width of 2×50 μm are designed and fabricated. Their excellent DC and RF c... In this paper, 0.15-μm gate-length In0.52Al0.48As/In0.53Ga0.47As InP-based high electron mobility transistors (HEMTs) each with a gate-width of 2×50 μm are designed and fabricated. Their excellent DC and RF characterizations are demonstrated. Their full channel currents and extrinsic maximum transconductance (gm,max) values are measured to be 681 mA/mm and 952 mS/mm, respectively. The off-state gate-to-drain breakdown voltage (BVGD) defined at a gate current of-1 mA/mm is 2.85 V. Additionally, a current-gain cut-off frequency (fT) of 164 GHz and a maximum oscillation frequency (fmax) of 390 GHz are successfully obtained; moreover, the fmax of our device is one of the highest values in the reported 0.15-μm gate-length lattice-matched InP-based HEMTs operating in a millimeter wave frequency range. The high gm,max, BVGD, fmax, and channel current collectively make this device a good candidate for high frequency power applications. 展开更多
关键词 breakdown voltage cut-off frequency high electron mobility transistors maximum oscillation frequency
下载PDF
微过充条件下锂离子电池的老化机理 被引量:2
18
作者 王银飞 杨铮鑫 +1 位作者 杜进桥 蒋方明 《电池》 CAS 北大核心 2023年第5期499-503,共5页
锂离子电池容易发生微过充导致电池失效,影响整个电池系统的安全。通过不同充电截止电压(3.6 V、3.7 V、3.8 V和3.9 V)下的磷酸铁锂锂离子电池微过充循环实验发现:微过充循环后的电池与正常循环电池相比,容量衰减更快;微过充后电池发生... 锂离子电池容易发生微过充导致电池失效,影响整个电池系统的安全。通过不同充电截止电压(3.6 V、3.7 V、3.8 V和3.9 V)下的磷酸铁锂锂离子电池微过充循环实验发现:微过充循环后的电池与正常循环电池相比,容量衰减更快;微过充后电池发生的老化机理为锂库存损失(LLI)和活性材料损失(LAM),且LLI与LAM之比随着充电截止电压的升高而增大,3.9 V充电截止电压条件下,电池LLI和LAM分别达到20.37%和22.17%。此外,欧姆内阻和极化内阻都随着截止电压的升高而增大,且固体电解质相界面(SEI)膜也在不断增厚。 展开更多
关键词 微过充 锂离子电池 老化机理 容量衰减 截止电压
下载PDF
高渗透率分布式电源影响下配电网极限线损计算方法 被引量:3
19
作者 张晋铭 欧阳森 +2 位作者 辛曦 郭一帆 张杰宁 《广东电力》 2023年第4期21-31,共11页
针对现有配电网极限线损研究中未能充分考虑高渗透率分布式电源(distributed generation,DG)下节点电压越限、上级系统有功平衡功率损失等情况,使得极限线损的计算考虑不周的问题,提出一种高渗透率DG影响下配电网的极限线损计算方法。首... 针对现有配电网极限线损研究中未能充分考虑高渗透率分布式电源(distributed generation,DG)下节点电压越限、上级系统有功平衡功率损失等情况,使得极限线损的计算考虑不周的问题,提出一种高渗透率DG影响下配电网的极限线损计算方法。首先,考虑该背景影响下的电压越限问题,设计以DG有功、无功出力的最小变化差为目标的电压调控策略,构建计及DG出力变化的极限线损模型,使其更符合实际运行情况;其次,在模糊算法原理基础上以不同渗透率为程度界限,构建半梯形隶属度函数及对应模糊规则,得到上级系统有功平衡功率损失模型,并在供电功率不足时,构建计及削负荷操作的配电网极限线损模型;最后,以改进的IEEE 33节点配电系统为例,基于概率潮流分别讨论DG并入后极限线损减小、增大2种情况,验证所提极限线损模型的有效性。 展开更多
关键词 高渗透率 分布式电源 电压调控 削负荷 概率潮流 极限线损
下载PDF
高气压环境等离子弧行为与工艺研究
20
作者 李勇 佟浩东 +1 位作者 高辉 周灿丰 《焊接学报》 EI CAS CSCD 北大核心 2023年第6期82-89,I0008,共9页
等离子弧切割技术因其高效稳定的工艺优势被广泛应用于工业领域.文中以空气等离子弧为研究对象,通过COMSOL Multiphysics软件建立了喷嘴结构的二维轴对称有限元数学模型,并对电弧磁流体模型进行了优化.基于磁流体动力学和电弧等离子体理... 等离子弧切割技术因其高效稳定的工艺优势被广泛应用于工业领域.文中以空气等离子弧为研究对象,通过COMSOL Multiphysics软件建立了喷嘴结构的二维轴对称有限元数学模型,并对电弧磁流体模型进行了优化.基于磁流体动力学和电弧等离子体理论,选用等离子平衡放电多物理场接口,并确立了空气等离子电弧模型的控制方程和边界条件,实现对电弧模型的编译求解.仿真结果表明,在引弧电流一致的条件下,随着环境压力的增加,电弧在温度分布和速度分布上均呈现收缩的态势.基于3 MPa高压焊接试验舱,搭建了高压环境等离子弧切割实验系统,通过对气路和非高频引弧电路的优化设计,实现了环境压力为0.1~0.7 MPa的稳定起弧.并基于此开展了高压梯度下的等离子弧切割实验,并结合切割质量指标研究了环境压力对等离子弧电离行为的影响. 展开更多
关键词 高压环境 等离子弧电离行为 引弧 切割工艺 仿真试验
下载PDF
上一页 1 2 12 下一页 到第
使用帮助 返回顶部