Cultural Practices for Propagation of Spatholobus suberectus via Cutting into Polybags

In this paper,the propagation of Spatholobus suberectus Dunn.was optimized based on the research results conducted in propagation for many years and the actual need for the planting materials.According to the requirements of Good Agricultural Practices for Chinese Medicinal Drugs,cultural practices for propagation of S.suberectus were summed up and standardized,including the environmental requirements,land preparation,bed preparation,cutting of scions,cuttings treatment,cutting,management of cuttings at the nursery,bagged cuttings ready for transplanting,packing and handling,transportation,and preparation of records for archives.

Investigation of a non-explosive directional roof cutting technology for self-formed roadway

Traditional explosives have characteristics of high risk,large vibration,and poor directional fracturing.Consequently,an instantaneous expander with a single crack surface(IESCS),which is a novel nonexplosive directional rock-breaking technique,has been developed.The directional roof-cutting mechanism of the IESCS method,driven by high-pressure gas,was theoretically analyzed.Laboratory experiments and numerical simulations proved the directional slitting effect of the IESCS method to be excellent.Compared with shaped-charge blasting,the charge of IESCS was reduced by 8.9%,but the crack rate increased by 9%in field tests.After IESCS pre-splitting,the roof directionally collapsed along the cutting line,and the gangue filled the goaf.Moreover,the directional roof cutting by the IESCS could decrease roadway stress.The average pressure of hydraulic supports on the cutting side of the roof was 31%lower than that on the non-cutting side of the roof after pre-splitting.After the self-formed roadway constructed by the IESCS was stabilized,the final relative displacement of the roof and floor was 157.3 mm,meeting the required standard of the next working face.Thus,the IESCS was effectively applied to directional roof pre-splitting.The results demonstrate the promising potential of IESCS in the mining and geotechnical fields.

FORMING PRINCIPLE OF TWO SIDE-DIRECTION BURR AND IT'S PREDICTION IN METAL CUTTING

The burr is one of the common phenomena occurring i n metal cutting operations The mathematical mechanical model of two side dir ection burr formation and transformation is established with plane stress strain theory,based on the orthogonal cutting The main laws of formation and change of the burr are revealed,and it is confirmed by experiment result,which first realizes prediction of the forming and changing of the two side direction burr in metal cutting operation.

Comprehensive Review of Studies on Metamorphic Rocks

Marble is a metamorphic rock, which is one of the 3 basic rock types (magmatic, sedimentary, metamorphic) forming the earth’s crust. The major characteristic sought after in a rock mass in the field for it to be exportable and usable as marble is its suitability to be cut in blocks. In the process of producing marble slabs from marble blocks, the blocks are expected not to contain potentially problematic hard or weak zones and their geomechanical and chemical properties should conform to the relevant standards. Ignoring of the geological properties of the rock in the process of deciding for marble production at a marble site and determination of production location, direction and method is the most important parameter that would increase production loss. In order to reduce losses by determination of geological properties of marble, many academic studies have been conducted on the effects of water saturation, temperature, freezing and thawing on its mechanical and fracture properties. There are further studies on crack propagation in marble under stress. However, even those marble blocks that are obtained based on geological parameters may suffer serious cracks or fractures due to stresses caused by their weight and geometry. Therefore, cutting direction is of critical importance in order to minimize marble waste in the process of cutting a marble block which is brought to the inventory or processing site with cracks, cavities or fractures. Certain studies exist within such context, where the geometry of the discontinuity within a block is determined using non-destructive methods, such as ultrasonic testing, in order to determine the appropriate cutting direction. Such studies made use of ultrasonic waves to determine the physical and chemical structures of magmatic and sedimentary rocks by measuring the progress velocity of sonic waves in the rock. Said studies, however, mostly worked on sedimentary and magmatic rock specimens, focusing less on metamorphic rocks such as marble due to their anisotropic properties. Understanding the academic literature studies on marble would provide significant contribution to the reduction of production losses during the processing marble blocks in processing plants and the achievement of production efficiency levels that are within economic limits. Within such scope, this study has reviewed the past academic studies on marble, classified them under 6 categories, and comprehensively analyzed each category based on materials, testing setups, test specimens, test parameters and research techniques.