Zr-doping stabilizes spinel LiMn_(2)O_(4)as a low cost long cycle life cathode for lithium ion batteries

The present commercial spinel LiMn_(2)O_(4) delivers only 90 m Ah/g–115 m Ah/g,far lower than the theoretical specific capacity.It degrades fast caused by the Jahn–Teller effect,Mn dissolution and related side reactions that consume Li inventory.In this work,Zr doping is employed to improve the structural stability and electrochemical performance of spinel LiMn_(2)O_(4).Li_(1.06)Mn_(1.94-x)Zr_xO_4(x=0,0.01,0.02,0.04)have been successfully synthesized by a simple solid-state reaction method and evaluated as cathode for lithium ion batteries(LIB).Li_(1.06)Mn_(1.92)Zr_(0.02)O_4 is superior cathode material with a high capacity of 122 m Ah/g at 1-C rate;long cycle stability,98.39%retention after 100 cycles at 1-C rate,excellent high rate performance 107.1 m Ah/g at 10-C rate,and high temperature performance 97.39%retention after 60 cycles.These are thought to be related to Zr doping effectively stabilizing the spinel LiMn_(2)O_(4),by forming stronger Zr–O bonds in the octahedron,suppressing the Jahn–Teller effect,thus improving electrochemical performance.

CNTs@S composite as cathode for all-solid-state lithium-sulfur batteries with ultralong cycle life

The main challenges in development of traditional liquid lithium-sulfur batteries are the shuttle effect at the cathode caused by the polysulfide and the safety concern at the Li metal anode arose from the dendrite formation.All-solid-state lithium-sulfur batteries have been proposed to solve the shuttle effect and prevent short circuits.However,solid-solid contacts between the electrodes and the electrolyte increase the interface resistance and stress/strain,which could result in the limited electrochemical performances.In this work,the cathode of all-solid-state lithium-sulfur batteries is prepared by depositing sulfur on the surface of the carbon nanotubes(CNTs@S)and further mixing with Li10GeP2S12 electrolyte and acetylene black agents.At 60℃,CNTs@S electrode exhibits superior electrochemical performance,delivering the reversible discharge capacities of 1193.3,959.5,813.1,569.6 and 395.5 mAhg^-1 at the rate of 0.1,0.5,1,2 and 5 C,respectively.Moreover,the CNTs@S is able to demonstrate superior high-rate capability of 660.3 mAhg^-1 and cycling stability of 400 cycles at a high rate of 1.0 C.Such uniform distribution of the CNTs,S and Li10GeP2S12 electrolyte increase the electronic and ionic conductivity between the cathode and the electrolyte hence improves the rate performance and capacity retention.

An exPerimental study of effect of solder joint geometry on thermal cycle life in SMT

The geometry of solder joint in SMT is one of the important factors whichdetermine the solder joint reliability. In this study, a type of solder joint specimen has beendesigned and is subjected to thermal cycling to failure between -55 ℃ to +125 ℃ with a 36℃/min heating and cooling rate and 10 min temperature holding times. The solder jointgeometry is castellated and controlled with different solder fillet shape and stand off height.A statistical analysis of the scattered thermal cycle lives of solder joints by two parameterWeibull's probability density function has been carried out in this paper. The experimentalresults show that the more reliable solder joint geometry has flat or slight convex solderfillet with a stand off height larger than 0.1 mm. The results may be the recommendedguideline to design optimal solder joint geometry.

High energy density performance of hydrothermally produced hydrous ruthenium oxide/multiwalled carbon nanotubes composite: Design of an asymmetric supercapacitor with excellent cycle life

Hydrous ruthenium oxide(h-Ru O) nanoparticles and its composite with multiwalled carbon nanotubes(h-Ru O/MWCNT) were synthesized by a simple hydrothermal method and proved to have potential application as hybrid supercapacitor material.The h-Ru Oand h-Ru O/MWCNT were characterized for their physico-chemical properties by PXRD,BET surface area,Raman,SEM-EDS and TEM techniques.The electrochemical performance of the materials were investigated,specific capacitance(Cs) of h-Ru Oand hRu O/MWCNT estimated by their cyclic voltammetric studies were found to be 604 and 1585 F/g respectively at a scan rate of 2 m V/s in the potential range 0–1.2 V.Further,this value was found to be nearly three times higher than that of pure h-Ru O.An asymmetric supercapacitor(AS) device was fabricated by employing h-Ru O/MWCNT as the positive electrode and activated carbon as the negative electrode.The device exhibited Cs of 61.8 F/g at a scan rate of 2 m V/s.Further,the device showed excellent long term stability for 20,000 cycles with 88% capacitance retention at a high current density of 25 A/g.

Amorphous phosphorus chalcogenide as an anode material for lithiumion batteries with high capacity and long cycle life

The ever-increasing demands for modern energy storage applications drive the search for novel anode materials of lithium(Li)-ion batteries(LIBs) with high storage capacity and long cycle life, to outperform the conventional LIBs anode materials. Hence, we report amorphous ternary phosphorus chalcogenide(aP_(4)SSe_(2)) as an anode material with high performance for LIBs. Synthesized via the mechanochemistry method, the a-P_(4)SSe_(2) compound is endowed with amorphous feature and offers excellent cycling stability(over 1500 mA h g^(-1) capacity after 425 cycles at 0.3 A g^(-1)), owing to the advantages of isotropic nature and synergistic effect of multielement forming Li-ion conductors during battery operation. Furthermore,as confirmed by ex situ X-ray diffraction(XRD) and transmission electron microscope(TEM), the a-P_(4)SSe_(2)anode material has a reversible and multistage Li-storage mechanism, which is extremely beneficial to long cycle life for batteries. Moreover, the autogenous intermediate electrochemical products with fast ionic conductivity can facilitate Li-ion diffusion effectively. Thus, the a-P_(4)SSe_(2)electrode delivers excellent rate capability(730 mA h g^(-1)capacity at 3 A g^(-1)). Through in situ electrochemical impedance spectra(EIS) measurements, it can be revealed that the resistances of charge transfer(R_(SEI)) and solid electrolyte interphase(R_(Ct)) decrease along with the formation of Li-ion conductors whilst the ohmic resistance(R_(Ω)) remains unchanged during the whole electrochemical process, thus resulting in rapid reaction kinetics and stable electrode to obtain excellent rate performance and cycling ability for LIBs. Moreover, the formation mechanism and electrochemical superiority of the a-P_(4)SSe_(2)phase, and its expansion to P_(4)S_(3-x)Se_(x)(x = 0, 1, 2, 3) family can prove its significance for LIBs.

Tailored architecture of composite electrolyte for all-solid-state sodium batteries with superior rate performance and cycle life

Seeking for composite electrolytes reinforced all-solid-state sodium ion batteries with superior long lifespan and rate performance remains a great challenge.Here,a unique strategy to tailor the architecture of composite electrolyte via inserting polymer chains into a small quantity of sulfate sodium grafted C_(48)0H_(28)O_(32)Zr_(6)(UIOSNa)is proposed.The intimate contact between polymer segments and UIOSNa with limited pore size facilitates the anion immobilization of sodium salts and reduction of polymer crystallinity,thereby providing rapid ion conduction and reducing the adverse effect caused by the immigration of anions.The tNa+grafting of-SO_(3)Na groups on fillers allows the free movement of more sodium ions to further improve and ionic conductivity.Consequently,even with the low content of UIOSNa fillers,a high ionic conductivity of 6.62×10^(-4) S·cm^(-1) at 60℃ and a transference number of 0.67 for the special designed composite electrolyte are achieved.The assembled all-solid-state sodium cell exhibits a remarkable rate performance for 500 cycles with 95.96%capacity retention at a high current rate of 4 C.The corresponding pouch cell can stably work for 1000 cycles with 97.03%capacity retention at 1 C,which is superior to most of the reported composite electrolytes in the literature.

Growth of RB Population in the Conversion Phase of Chlamydia Life Cycle

Upon infecting a host cell,the reticulate body(RB)form of the Chlamydia bacteria simply proliferates by binary fission for an extended period.Available data show only RB units in the infected cells 20 hours post infection(hpi),spanning nearly half way through the development cycle.With data collected every 4 hpi,conversion to the elementary body(EB)form begins abruptly at a rapid rate sometime around 24 hpi.By modeling proliferation and conversion as simple birth and death processes,it has been shown that the optimal strategy for maximizing the total(mean)EB population at host cell lysis time is a bang-bang control qualitatively replicating the observed conversion activities.However,the simple birth and death model for the RB proliferation and conversion to EB deviates in a significant way from the available data on the evolution of the RB population after the onset of RB-to-EB conversion.By working with a more refined model that takes into account a small size threshold eligibility requirement for conversion noted in the available data,we succeed in removing the deficiency of the previous models on the evolution of the RB population without affecting the optimal bang-bang conversion strategy.

Tailoring Mg^(2+)Solvation Structure in a Facile All-Inorganic[Mg_(x)Li_(y)Cl2_(x+y)·nTHF]Complex Electrolyte for High Rate and Long Cycle-Life Mg Battery

A high-performance all-inorganic magnesium-lithium chloride complex(MLCC)electrolyte is synthesized by a simple room-temperature reaction of LiCl with MgCl_(2) in tetrahydrofuran(THF)solvent.Molecular dynamics simulation,density functional theory calculation,Raman spectroscopy,and nuclear magnetic resonance spectroscopy reveal that the formation of[Mg_(x)Li_(y)Cl_(2x+y)·nTHF]complex solvation structure significantly lowers the coordination number of THF in the first solvation sheath of Mg^(2+),which significantly enhances its de-solvation kinetics.The MLCC electrolyte presents a stable electrochemical window up to 3.1 V(vs Mg/Mg^(2+))and enables reversible cycling of Mg metal deposition/stripping with an outstanding Coulombic efficiency up to 99%at current densities as high as 10 mA cm^(-2).Utilizing the MLCC electrolyte,a Mg/Mo_(6)S_(8) full cell can be cycled for over 10000 cycles with a superior capacity retention of 85 mA h g^(-1) under an ultrahigh rate of 50 C(1 C=128.8 mA g^(-1)).The facile synthesis of highperformance MLCC electrolyte provides a promising solution for future practical magnesium batteries.

CeO_(2)-clay composites for ultra-long cycle life electrochemical capacitive energy storage application

The lattice expansion caused by the reduction of Ce(Ⅳ)to Ce(Ⅲ)impeded the development of the CeO_(2)as an effective electrode material for electrochemical supercapacitors.Herein,we prepared CeO_(2)-clay composites through a one-step hydrothermal method.The interlayer structures of clays efficiently accommodate volume changes induced by crystal lattice expansion to achieve ultra-long cycle stability.After 60000 charge-discharge cycles,the capacitance retention rate of the assembled asymmetric supercapacitors is as high as~-100%.The key findings of this work reveal the potential application of clays in achieving ultralong cycle stability of the CeO_(2)electrode material,paving the way for further application of the CeO_(2)in electrochemical energy storage.

Carbon footprint accounting for cigar production processes: A life cycle assessment perspective

Although the tobacco industry is a significant contributor to energy consumption and carbon emissions its negative environmental impact has received inadequate attention globally.Cigarette factories are a key link in the tobacco industry’s production chain,and using data provided by a cigarette factory in China we conduct a life cycle assessment to account for the carbon footprint of cigar production in cigarette factories.The results of the assessment show that factory air conditioning is the most important contributor to the environmental load of the cigar manufacturing process,while electricity is the key factor that contributes the greatest envi‐ronmental load across all of the processes in the product life cycle.In addition,packaging,including small boxes and cigarette cartons,has a significant impact on the industry’s environmental footprint due to its use of raw materials.We find the carbon footprint of the entire production process for cigar products to be 383.59 kg CO_(2) eq.Based on our findings,we suggest ways to optimize cigar/cigarette factory processes to re‐duce carbon emissions that can help to promote sustainable development in related industries.

Life Cycle Assessment Introduced by Using Nanorefrigerant of Organic Rankine Cycle System for Waste Heat Recovery

The use of nanorefrigerants in Organic Rankine Cycle(ORC)units is believed to affect the cycle environment performance,but backed with very few relevant studies.For this purpose,a life cycle assessment(LCA)has been performed for the ORC system using nanorefrigerant,the material and energy input,characteristic indicators and comprehensive index of environmental impact,total energy consumption and energy payback time(BPBT)of the whole life cycle of ORC system using Al_(2)O_(3)/R141b nanorefrigerant were calculated.Total environmental comprehensive indexes reveal that ECER-135 index decrease by 1.5%after adding 0.2%Al_(2)O_(3)nanoparticles to R141b.Based on the contribution analysis and sensitivity analysis,it can be found out ORC system manufacturing is of the most critical stage,where,the ECER-135 index of ORC component production is the greatest,followed by the preparation process of R141b,transportation phase,and that of Al_(2)O_(3)nanoparticles preparation is small.The retirement phase which has good environmental benefits affects the result significantly by recycling important materials.Meanwhile,the main cause and relevant suggestion for improvement were traced respectively.Finally,the environmental impacts of various power generations were compared,and results show that the power route is of obvious advantage.Among the renewable energy,ORC system using Al_(2)O_(3)/R141b nanorefrigerant with minimal environmental impact is only 0.67%of coal-fired power generation.The environmental impact of current work is about 14.34%of other nations’PV results.

Carbon emissions reduction potentiality for railroad transportation based on life cycle assessment

This study addresses the comparative carbon emissions of different transportation modes within a unified evaluation framework,focusing on their carbon footprints from inception to disposal.Specifically,the entire life cycle carbon emissions of High-Speed Rail(HSR),battery electric vehicles,conventional internal combustion engine vehicles,battery electric buses,and conventional internal combustion engine buses are analyzed.The life cycle is segmented into vehicle manufacturing,fuel or electricity production,operational,and dismantlingrecycling stages.This analysis is applied to the Beijing-Tianjin intercity transportation system to explore emission reduction strategies.Results indicate that HSR demonstrates significant carbon emission reduction,with an intensity of only 24%-32% compared to private vehicles and 47%-89% compared to buses.Notably,HSR travel for Beijing-Tianjin intercity emits only 24% of private vehicle emissions,demonstrating the emission reduction benefits of transportation structure optimization.Additionally,predictive modeling reveals the potential for carbon emission reduction through energy structure optimization,providing a guideline for the development of effective transportation management systems.

Design of Fine Life Cycle Prediction System for Failure of Medical Equipment

The inquiry process of traditional medical equipment maintenance management is complex,which has a negative impact on the efficiency and accuracy of medical equipment maintenance management and results in a significant amount of wasted time and resources.To properly predict the failure of medical equipment,a method for failure life cycle prediction of medical equipment was developed.The system is divided into four modules:the whole life cycle management module constructs the life cycle data set of medical devices from the three parts of the management in the early stage,the middle stage,and the later stage;the status detection module monitors the main operation data of the medical device components through the normal value of the relevant sensitive data in the whole life cycle management module;and the main function of the fault diagnosis module is based on the normal value of the relevant sensitive data in the whole life cycle management module.The inference machine diagnoses the operation data of the equipment;the fault prediction module constructs a fine prediction system based on the least square support vector machine algorithm and uses the AFS-ABC algorithm to optimize the model to obtain the optimal model with the regularized parameters and width parameters;the optimal model is then used to predict the failure of medical equipment.Comparative experiments are designed to determine whether or not the design system is effective.The results demonstrate that the suggested system accurately predicts the breakdown of ECG diagnostic equipment and incubators and has a high level of support and dependability.The design system has the minimum prediction error and the quickest program execution time compared to the comparison system.Hence,the design system is able to accurately predict the numerous causes and types of medical device failure.

Polydopamine-mediated synthesis of Si@carbon@graphene aerogels for enhanced lithium storage with long cycle life

The application of Si as the anode materials for lithium-ion batteries(LIBs) is still severely hindered by the rapid capacity decay due to the structural damage caused by large volume change(> 300%) during cycling. Herein, a three-dimensional(3 D) aerogel anode of Si@carbon@graphene(SCG) is rationally constructed via a polydopamine-assisted strategy. Polydopamine is coated on Si nanoparticles to serve as an interface linker to initiate the assembly of Si and graphene oxide, which plays a crucial role in the successful fabrication of SCG aerogels. After annealing the polydopamine is converted into N-doped carbon(N-carbon) coatings to protect Si materials. The dual protection from N-carbon and graphene aerogels synergistically improves the structural stability and electronic conductivity of Si, thereby leading to the significantly improved lithium storage properties. Electrochemical tests show that the SCG with optimized graphene content delivers a high capacity(712 m Ah/g at 100 m A/g) and robust cycling stability(402 m Ah/g at 1 A/g after 1500 cycles). Furthermore, the full cell using SCG aerogels as anode exhibits a reversible capacity of 187.6 m Ah/g after 80 cycles at 0.1 A/g. This work provides a plausible strategy for developing Si anode in LIBs.

Synthesis of Co-Ni oxide microflowers as a superior anode for hybrid supercapacitors with ultralong cycle life

Li-ion hybrid capacitors（LIHCs）,composing of a lithium-ion battery（LIB） type anode and a supercapacitor（SC） type cathode,gained worldwide popularity due to harmonious integrating the virtues of high energy density of LIBs with high power density of SCs.Herein,nanoflakes composed microflower-like Co-Ni oxide（CoNiO） was successfully synthesized by a simple co-precipitation method.The atomic ratio of as-synthesized CoNiO is determined to be 1：3 through XRD and XPS analytical method.As a typical battery-type material,CoNiO and capacitor-type activated polyanilinederived carbon（APDC） were used to assemble LIHCs as the anode and cathode materials,respectively.As a result,when an optimized mass ratio of CoNiO and APDC was 1：2,CoNiO//APDC LIHC could deliver a maximum energy density of 143 Wh kg^-1 at a working voltage of 1-4 V.It is worth mentioning that the LIHC also exhibits excellent cycle stability with the capacitance retention of -78.2%after 15,000 cycles at a current density of 0.5 A g^-1.

Two-stage aging trajectory prediction of LFP lithium-ion battery based on transfer learning with the cycle life prediction

With the wide application of the LFP lithium-ion batteries,more attention is paid to the battery life and future aging behaviors as the safety and performance of the battery are guaranteed by accurate battery aging monitoring.In recent years,long-term aging trajectory prediction of the lithium-ion battery is always a challenge due to its complex nonlinear aging behaviors especially the aging behaviors in the two aging stages are quite different when the battery experiences the two-stage aging process under fast-charging conditions.Thus,it is harder to achieve accurate long-term aging trajectory prediction of the LFP lithium-ion batteries on the condition of the two-stage aging process.To address it,a novel transfer learning strategy combined with the cycle life prediction technology is presented in this paper.Specifically,a new cycle life prediction method is proposed based on feature extraction and deep learning technology and achieves accurate cycle life prediction.The transfer learning is started by developing a base aging model offline to learn the information of the two-stage aging process.Then,taking the predicted cycle life as its prior information,the Bayesian model migration technology is employed to predict the aging trajectory accurately,and the uncertainty of the aging trajectory is quantified.Two batches of the battery datasets are used for performance evaluation and comparison with two benchmarks.It is novel to combine the cycle life prediction and transfer learning technique to achieve accurate two-stage aging trajectory prediction with only a few data available(first 30%).

Universal organic anodes enable safe low-cost aqueous rechargeable batteries with long cycle life,high capacity, and fast kinetics

Future battery advances and economies of scale will help scrub CO2emissions from transportation and the grid.Economical energy storage lets battery-powered electric vehicles replace internal combustion engines in the transportation sector,which now accounts for the plurality of CO2emissions.For grid-scale applications,the benefits of adding storage are many and well documented[1–2].Beyond increased penetration of intermittent renewable energy generated from such as solar panels

Chinese life cycle impact assessment factors

The methodological basis and procedures for determination of Chinese normalization references and weighting factors according to the EDIP-method is described. According to Chinese industrial development intensity and population density, China was divided into three regions and the normalization references for each region were calculated on the basis of an inventory of all of the region's environmental emissions in 1990. The normalization reference was determined as the total environmental impact potential for the area in question in 1990(EP(j)90) divided by the population. The weighting factor was determined as the normalization reference (ER(j)90) divided by society's target contribution in the year 2000 based on Chinese political reduction plans, ER(j)T2000. This paper presents and discuss results obtained for eight different environmental impact categories relevant for China: global warming, stratospheric ozone depletion, acidification, nutrient enrichment, photochemical ozone formation and generation of bulk waste, hazardous waste and slag and ashes.

Overall Life Cycle Comprehensive Assessment of Pneumatic and Electric Actuator

Pneumatic actuators and electric actuators have almost been applied to all manufacturing industries. The two kinds of actuators can replace each other in most fields, such as the point to point transmission occasion and some rotating occasions. However, there are very few research results about the advantages and disadvantages of two kinds of actuators under the same working conditions so far. In this paper, a novel comprehensive assessment method, named as overall life cycle comprehensive assessment （OLCCA）, is proposed for comparison and assessment of pneumatic and electric actuators. OLCCA contains mechanical properties evaluation （MPE）, life cycle cost analysis based on users （LCCABOU） and life cycle environmental impact analysis （LCEIA） algorithm in order to solve three difficult problems： mechanical properties assessment, cost analysis and environmental impact assessment about actuators. The mechanical properties evaluation of actuators is a multi-objective optimization problem. The fuzzy data quantification and information entropy methods are combined to establish MPE algorithm of actuators. Two kinds of pneumatic actuators and electric actuators with similar bearing capacity and similar work stroke were taken for example to verify the correctness of MPE algorithm. The case study of MPE algorithm for actuators verified its correctness. LCCABOU for actuators is also set up. Considering cost complex structure of pneumatic actuators, public device cost even method （PDCEM） is firstly presented to solve cost division of public devices such as compressors, aftercooler, receivers, etc. LCCABOU method is also effective and verified by the three groups of pneumatic actuators and electric actuators. Finally, LCEIA model of actuators is established for the environmental impact assessment of actuators. LCEIA data collection method and model establishment procedure for actuators are also put forward. With Simapro 7, LCEIA comparison results of six actuators can be obtained： Fossil fuels are the major environmental factor of pneumatic and electric actuators; Environmental impact of electric actuator is large than one of pneumatic actuator under the similar mechanical properties and working conditions of pneumatic and electric actuators. The results are correct and correspond with the actual mechanical properties of actuators. This paper proposes a comprehensive evaluation method of the actuators, which can solve the critical problem that similar electromechanical products are very difficult to be compared with each other from the angle of performance, cost and environment impact.

A techno-economic and life cycle assessment for the production of green methanol from CO_(2): catalyst and process bottlenecks

The success of catalytic schemes for the large-scale valorization of CO_(2) does not only depend on the development of active,selective and stable catalytic materials but also on the overall process design.Here we present a multidisciplinary study(from catalyst to plant and techno-economic/lifecycle analysis)for the production of green methanol from renewable H2 and CO_(2).We combine an in-depth kinetic analysis of one of the most promising recently reported methanol-synthesis catalysts(InCo)with a thorough process simulation and techno-economic assessment.We then perform a life cycle assessment of the simulated process to gauge the real environmental impact of green methanol production from CO_(2).Our results indicate that up to 1.75 ton of CO_(2) can be abated per ton of produced methanol only if renewable energy is used to run the process,while the sensitivity analysis suggest that either rock-bottom H2 prices(1.5$kg1)or severe CO_(2) taxation(300$per ton)are needed for a profitable methanol plant.Besides,we herein highlight and analyze some critical bottlenecks of the process.Especial attention has been paid to the contribution of H2 to the overall plant costs,CH4 trace formation,and purity and costs of raw gases.In addition to providing important information for policy makers and industrialists,directions for catalyst(and therefore process)improvements are outlined.