Experimental investigation of the inhibition of deep-sea mining sediment plumes by polyaluminum chloride

Deep-sea sediment disturbance may occur when collecting polymetallic nodules,resulting in the creation of plumes that could have a negative impact on the ecological environment.This study aims to investigate the potential solution of using polyaluminum chloride(PAC)in the water jet.The effects of PAC are examined through a self-designed simulation system for deep-sea polymetallic nodule collection and sediment samples from a potential deep-sea mining area.The experimental results showed that the optimal PAC dose was found to be 0.75 g/L.Compared with the test conditions without the addition of PAC,the presence of PAC leads to a reduction in volume,lower characteristic turbidity,smaller diffusion velocity,and shorter settling time of the plume.This indicates that PAC inhibits the entire development process of the plume.The addition of PAC leads to the flocculation of mm-sized particles,resulting in the formation of cm-sized flocs.The flocculation of particles decreases the rate of erosion on the seabed by around 30%.This reduction in erosion helps to decrease the formation of plumes.Additionally,when the size of suspended particles increases,it reduces the scale at which they diffuse.Furthermore,the settling velocity of flocs(around 10^(-2) m/s)is much higher that of compared to sediment particles(around 10^(-5) m/s),which effectively reduces the amount of time the plume remains in suspension.

Gravity-Driven Listric Growth Fault and Sedimentation in the Lagoa do Peixe, Rio Grande do Sul Coastal Plain, Brazil

High frequency, high resolution GPR surveys are successfully applied to investigate near-surface stratification architecture of sedimentary units in coastal plains and to define their depositional conditions. However, low frequency GPR surveys to investigate fault-related depositional systems at greater depths are scarce. This survey was designed investigate a > 100 km long linear escarpment that controls the northwest margin of the Lagoa do Peixe, an important lagoon in Rio Grande do Sul Coastal Plain (RGSCP, Brazil). The traditional approach points that RGSCP was developed by juxtaposition of four lagoons/barrier systems as consequence of sea level changes;no deformational structure is admitted to exist before. The low frequency GPR (50 MHz, RTA antenna) and geological surveys carried out in the RGSCP showed the existence of a large, gravity-driven listric growth fault controlling the Lagoa do Peixe escarpment and hangingwall sedimentation. The radargrams in four subareas along the Lagoa do Peixe Growth Fault could be interpreted following the seismic expression of rift-related depositional systems. The radargrams enabled to distinguish three main lagoonal deposition radarfacies. The lower lagoonal radarfacies is a convex upward unit, thicker close to growth fault;the radarfacies geometry indicates that fault displacement rate surpasses the sedimentation rate, and its upper stratum is aged ~3500 l4C years BP. The second lagoonal radarfacies is a triangular wedge restricted to the lagoon depocenter, whose geometry indicates that fault displacement and the sedimentation rates kept pace. The upper lagoonal radarfacies is being deposited since 1060 ± 70 l4C years BP, under sedimentation rate higher than fault displacement rate. The results indicate that low frequency GPR surveys can help in investigating fault-related depositional systems in coastal zones. They also point to a new approach in dealing with RGSCP stratigraphy.

Volume-averaged modeling of multiphase solidification with equiaxed crystal sedimentation in a steel ingot

Macrosegregation is a critical factor that limits the mechanical properties of materials.The impact of equiaxed crystal sedimentation on macrosegregation has been extensively studied,as it plays a significant role in determining the distribution of alloying elements and impurities within a material.To improve macrosegregation in steel connecting shafts,a multiphase solidification model that couples melt flow,heat transfer,microstructure evolution,and solute transport was established based on the volume-averaged Eulerian-Eulerian approach.In this model,the effects of liquid phase,equiaxed crystals,columnar dendrites,and columnar-to-equiaxed transition(CET)during solidification and evolution of microstructure can be considered simultaneously.The sedimentation of equiaxed crystals contributes to negative macrosegregation,where regions between columnar dendrites and equiaxed crystals undergo significant A-type positive macrosegregation due to the CET.Additionally,noticeable positive macrosegregation occurs in the area of final solidification in the ingot.The improvement in macrosegregation is beneficial for enhancing the mechanical properties of connecting shafts.To mitigate the thermal convection of molten steel resulting from excessive superheating,reducing the superheating during casting without employing external fields or altering the design of the ingot mold is indeed an effective approach to control macrosegregation.

Numerical simulation on sand sedimentation and erosion characteristics around HDPE sheet sand barrier under different wind angles

For the safety of railroad operations,sand barriers are utilized to mitigate wind-sand disaster effects.These disasters,characterized by multi-directional wind patterns,result in diverse angles among the barriers.In this study,using numerical simulations,we examined the behavior of High Density Polyethylene(HDPE)sheet sand barriers under different wind angles,focusing on flow field distribution,windproof efficiency,and sedimentation erosion dynamics.This study discovered that at a steady wind speed,airflow velocity varies as the angle between the airflow and the HDPE barrier changes.Specifically,a 90°angle results in the widest low-speed airflow area on the barrier’s downwind side.If the airflow is not perpendicular to the barrier,it prompts a lateral airflow movement which decreases as the angle expands.The windproof efficiency correlates directly with this angle but inversely with the wind’s speed.Notably,with a wind angle of 90°,wind speed drops by 81%.The minimum wind speed is found at 5.1H(the sand barrier height)on the barrier’s downwind side.As the angle grows,the barrier’s windproof efficiency improves,extending its protective reach.Sedimentation is most prominent on the barrier’s downwind side,as the wind angle shifts from 30°to 90°,the sand sedimentation area on the barrier’s downwind side enlarges by 14.8H.As the angle grows,sedimentation intensifies,eventually overtakes the forward erosion and enlarges the sedimentation area.

Investigation of the Clinical Diagnostic Significance of the T-Cell Test for Tuberculosis combined with Erythrocyte Sedimentation Test in Pulmonary Tuberculosis

Objective:To investigate the clinical diagnostic significance of peripheral blood T-cell test(T-spot test)for tuberculosis(TB)infection combined with erythrocyte sedimentation rate(ESR)in pulmonary TB.Methods:41 patients with a clinical diagnosis of TB during hospitalization from January 2020 to April 2023 in our hospital were selected as the experimental group,and 45 patients without TB(bronchopneumonia patients)were selected as the control group.The diagnostic specificity,sensitivity,and accuracy of the T-spot TB test,ESR test,and the combined test of the two were calculated respectively.Results:The sensitivity,specificity,and accuracy of the T-spot TB test combined with ESR for the diagnosis of TB in the experimental group were significantly higher than the individual results of the T-spot TB test and ESR test alone(P<0.05).Conclusion:The T-spot TB test combined with the ESR test for TB diagnosis has greater clinical value than carrying out the tests individually.

Effects of sand sedimentation and wind erosion around sand barrier:Numerical simulation and wind tunnel test studies

Based on numerical simulations,this study highlights the sedimentation and erosion problems around a sand barrier through the relationship between the shear stress of the surface around the sand barrier and the critical shear stress of sand grains.The numerical simulation results were verified using data measured by the wind tunnel test.The results showed that when the porosity was the same,the size and position of the vortex on the leeward side of the sand barrier were related to the inlet wind speed.As the wind speed increased,the vortex volume increased and the positions of the separation and reattachment points moved toward the leeward side.When the porosity of the sand barrier was 30%,the strength of the acceleration zone above the sand barrier was the highest,and the strength of the acceleration zone was negatively correlated with the porosity.Sand erosion and sedimentation distance were related to wind speed.With an increase in wind speed,the sand grain forward erosion or reverse erosion areas on the leeward side of the sand barrier gradually replaced the sedimentation area.With an increase in porosity,the sand sedimentation distance on the leeward side of the sand barrier gradually shortened,and the sand erosion area gradually disappeared.The sand sedimentation distance on the leeward side of the sand barrier with 30%porosity was the longest.The numerical simulation results were in good agreement with the wind tunnel test results.Based on the sand erosion and sedimentation results of the numerical simulation and wind tunnel test,when the porosity was 30%,the protection effect of the High Density Polyethylene(HDPE)board sand barrier was best.

Dynamic coupled thermo-hydro-mechanical problem for heterogeneous deep-sea sediments under vibration of mining vehicle

Due to the influence of deep-sea environment,deep-sea sediments are usually heterogeneous,and their moduli of elasticity and density change as depth changes.Combined with the characteristics of deep-sea sediments,the thermo-hydro-mechanical coupling dynamic response model of heterogeneous saturated porous sediments can be established to study the influence of elastic modulus,density,frequency,and load amplitude changes on the model.Based on the Green-Lindsay generalized thermoelasticity theory and Darcy’s law,the thermo-hydro-mechanical coupled dynamic response model and governing equations of heterogeneous deep-sea sediments with nonlinear elastic modulus and density are established.The analytical solutions of dimensionless vertical displacement,vertical stress,excess pore water pressure,and temperature are obtained by means of normal modal analysis,which are depicted graphically.The results show that the changes of elastic modulus and density have few effects on vertical displacement,vertical stress,and temperature,but have great effects on excess pore water pressure.When the mining machine vibrates,the heterogeneity of deep-sea sediments has great influence on vertical displacement,vertical stress,and excess pore water pressure,but has few effects on temperature.In addition,the vertical displacement,vertical stress,and excess pore water pressure of heterogeneous deep-sea sediments change more gently.The variation trends of physical quantities for heterogeneous and homogeneous deep-sea sediments with frequency and load amplitude are basically the same.The results can provide theoretical guidance for deep-sea mining engineering construction.

Stress Path Analysis of Deep-Sea Sediments Under the Compression-Shear Coupling Load of Crawler Collectors

The mechanical properties of deep-sea sediments during the driving process of crawler collectors are essential factors in the design of mining systems.In this study,a crawler load is divided into a normal compression load and a horizontal shear load.Then,the internal stress state of sedimentary soil is examined through a theoretical calculation and finite element numerical simulation.Finally,the driving of crawlers is simulated by changing the relative spatial position between the load and stress unit,obtaining the stress path of the soil unit.Based on the calculation results,the effect of the horizontal shear load on the soil stress response is analyzed at different depths,and the spatial variation law of the soil stress path is examined.The results demonstrate that the horizontal shear load has a significant effect on the rotation of the principal stress,and the reverse rotation of the principal stress axis becomes obvious with the increase in the burial depth.The stress path curve of the soil is different at various depths.The spatial variation rule of the stress path of the shallow soil is complex,whereas the stress path curve of the deep soil tends to shrink as the depth increases.The stress path of the corresponding depth should be selected according to the actual research purpose and applied to the laboratory test.

Two Kinds of Waves Causing the Resuspension of Deep-Sea Sediments:Excitation and Internal Solitary Waves

The resuspension of marine sediments plays a key role in the biogeochemical cycle and marine ecology system.Internal solitary waves are considered to be important driving forces of the resuspension of bottom sediments.In this paper,the movement of turbidity currents,the generation and the effects on the bottom bed of internal solitary waves and excitation waves are studied by flume tests and numerical simulations,and the sediment resuspension are analyzed.The results show that the excitation wave can lead to the resuspension of the bottom sediments under all the conditions,while the internal solitary wave can lead to the resuspension of the sediment only under some special conditions,such as high amplitude or large underwater slope.Under the experimental conditions,the change in the near-bottom velocity caused by the excitation wave is close to three times that of the internal solitary wave.

Provenance and depositional setting of the Late MiocenePleistocene clastic sediments in the eastern Arabian Peninsula and western Iraq using rare earth elements geochemistry

The sandstones of the Late miocene–Pliocene Dibdibba Formation in the Najaf–Karbala Plateau and Basra were examined to determine their source rocks and origin. The rare earth elements(REE) and trace elements(Sc, Co, V, and Th) concentrations in these sandstones revealed that they likely derived from a single source. The steep light rare earth elements(LREE) and flat, heavy rare earth element(HREE) patterns, negative Eu anomaly, and high ΣREE contents in sandstones suggest its derivation from a suggests that a passive continental margin environment and originated from felsic source rocks. The average concentration of ΣREE is 93.5 ppm, which is lower than that of the average crustal compositions like Upper Continental Crust and Post Archean Australian Shale. The higher proportion of LREE compared to HREE implies that these sandstones were recycled and derived from a distal source. The Th/Co, Th/Sc, La/Sc, La/Co, Eu/Eu*and(La/Lu)cn elemental ratios indicated that these Late Miocene–Pliocene sandstones were derived from felsic rocks located in the marginal region of the Arabian Shield.

Removal Effect of Coagulating Sedimentation Method on Polyethylene Microplastics in Water

Microplastic is a new kind of pollutant.It exists widely in the aquatic environment and seriously endangers the aquatic ecosystem.In this study,the coagulating sedimentation method was used to remove microplastics in water.Polyethylene(PE)was selected as the representative of microplastics,polyferric sulfate(PFS),polyaluminum chloride(PAC)and aluminum sulfate(AS)were used as coagulant,and polyacrylamide(PAM)was used as coagulant aid to study the effects of pH,coagulant concentration and sedimentation time on the removal of PE by single and composite coagulant.The results showed that when the dosage of PFS was 0.5 g/L and pH was 5.0,the removal rate could reach 82.14%,which was better than PAC and AS,indicating that PFS had better coagulation and sedimentation performance for PE;the composite coagulant of PFS+PAC+AS(1 g/L+0.2 g/L+0.2 g/L,pH was 5.0)had the highest removal rate of PE,reaching 96.06%;the removal rate of PE increased with the increase in sedimentation time,but considering that the longer sedimentation time has less contribution to the improvement of removal rate,it is recommended that 4 h is appropriate.

The control of astronomical cycles on lacustrine fine-grained event Sedimentation——A case study of the Chunshang sub-member of the upper Es_(4) in the Dongying Sag

Fine-grained lacustrine sedimentation controlled by astronomical cycles remains a research weakness in sedimentology studies,as most studies have concentrated on how astronomical cycles affect the normal lacustrine fine-grained sedimentation,but how they affect the lacustrine fine-grained event sedimen-tation has been rarely studied.Therefore,this work researched the characteristics of event sedimentation by systematically observing the cores from 30 cored wells in the Shahejie Formation of the Dongying Sag at a depth of over 1800 m,with more than 4000 thin sections being authenticated and over 1000 whole rocks being analyzed by X-ray diffraction(XRD).The research object was the Chunshang Sub-member of Upper Es_(4) in the Fanye 1 well,as it had the most comprehensive analysis data and underwent the most continuous coring.We divided astronomical cycles into different orders and made corresponding curves using the gamma-ray(GR)curve,spectral analysis,power spectrum estimation,and module extreme values,there were 6 long eccentricity periods,22 short eccentricity periods,65.5 obliquity cycles,and 110.5 precession cycles in this sub-member.On this basis,this study analyzed the control of astronomical cycles on the lacustrine fine-grained event sedimentation,and the research shows deposits were developed by slide-slump,turbidities,hyperpycnites,and tempestites in the Chunshang Sub-member of the Upper Es_(4),with higher long eccentricity,the monsoon climate contributes to the formation of storm currents,while with lower long eccentricity,the surface deposits are severely eroded by rivers and rainfalls,thus developing the slide-slump,turbidities,and hyperpycnites.The relationship between the lacustrine fine-grained event sedimentation and astronomical cycles was studied in this case study,which can promote research on fine-grained sedimentary rocks in genetic dynamics and boost the theoretical and disciplinary development in fine-grained sedimentology.

Cycles of fine-grained sedimentation and their influences on organic matter distribution in the second member of Paleogene Kongdian Formation in Cangdong Sag,Bohai Bay Basin,East China

According to the theory of sequence stratigraphy based on continental transgressive-regressive(T-R)cycles,a 500 m continuous core taken from the second member of Kongdian Formation(Kong 2 Member)of Paleogene in Well G108-8 in the Cangdong Sag,Bohai Bay Basin,was tested and analyzed to clarify the high-frequency cycles of deep-water fine-grained sedimentary rocks in lacustrine basins.A logging vectorgraph in red pattern was plotted,and then a sequence stratigraphic framework with five-order high-frequency cycles was formed for the fine-grained sedimentary rocks in the Kong 2 Member.The high-frequency cycles of fine-grained sedimentary rocks were characterized by using different methods and at different scales.It is found that the fifth-order T cycles record a high content of terrigenous clastic minerals,a low paleosalinity,a relatively humid paleoclimate and a high density of laminae,while the fifth-order R cycles display a high content of carbonate minerals,a high paleosalinity,a dry paleoclimate and a low density of laminae.The changes in high-frequency cycles controlled the abundance and type of organic matter.The T cycles exhibit relatively high TOC and abundant endogenous organic matters in water in addition to terrigenous organic matters,implying a high primary productivity of lake for the generation and enrichment of shale oil.

Integrated biomarker response to assess toxic impacts of iron and manganese on deep-sea mussel Gigantidas platifrons under a deep-sea mining activity scenario

Deep-sea mining activities can potentially release metals,which pose a toxicological threat to deep-sea ecosystems.Nevertheless,due to the remoteness and inaccessibility of the deep-sea biosphere,there is insufficient knowledge about the impact of metal exposure on its inhabitants.In this study,deep-sea mussel Gigantidas platifrons,a commonly used deep-sea toxicology model organism,was exposed to manganese(100,1000μg/L)or iron(500,5000μg/L)for 7 d,respectively.Manganese and iron were chosen for their high levels of occurrence within deep-sea deposits.Metal accumulation and a battery of biochemical biomarkers related to antioxidative stress in superoxide dismutase(SOD),catalase(CAT),malondialdehyde(MDA);immune function in alkaline phosphatase(AKP),acid phosphatase(ACP);and energy metabolism in pyruvate kinase(PK)and hexokinase(HK)were assessed in mussel gills.Results showed that deep-sea mussel G.platifrons exhibited a high capacity to accumulate Mn/Fe.In addition,most tested biochemical parameters were altered by metal exposure,demonstrating that metals could induce oxidative stress,suppress the immune system,and affect energy metabolism of deep-sea mussels.The integrated biomarker response(IBR)approach indicated that the exposure to Mn/Fe had a negative impact on deep-sea mussels,and Mn demonstrated a more harmful impact on deep-sea mussels than Fe.Additionally,SOD and CAT biomarkers had the greatest impact on IBR values in Mn treatments,while ACP and HK were most influential for the low-and high-dose Fe groups,respectively.This study represents the first application of the IBR approach to evaluate the toxicity of metals on deep-sea fauna and serves as a crucial framework for risk assessment of deep-sea mining-associated metal exposure.

Predicting impact forces on pipelines from deep-sea fluidized slides:A comprehensive review of key factors

Deep-sea pipelines play a pivotal role in seabed mineral resource development,global energy and resource supply provision,network communication,and environmental protection.However,the placement of these pipelines on the seabed surface exposes them to potential risks arising from the complex deep-sea hydrodynamic and geological environment,particularly submarine slides.Historical incidents have highlighted the substantial damage to pipelines due to slides.Specifically,deep-sea fluidized slides(in a debris/mud flow or turbidity current physical state),characterized by high speed,pose a significant threat.Accurately assessing the impact forces exerted on pipelines by fluidized submarine slides is crucial for ensuring pipeline safety.This study aimed to provide a comprehensive overview of recent advancements in understanding pipeline impact forces caused by fluidized deep-sea slides,thereby identifying key factors and corresponding mechanisms that influence pipeline impact forces.These factors include the velocity,density,and shear behavior of deep-sea fluidized slides,as well as the geometry,stiffness,self-weight,and mechanical model of pipelines.Additionally,the interface contact conditions and spatial relations were examined within the context of deep-sea slides and their interactions with pipelines.Building upon a thorough review of these achievements,future directions were proposed for assessing and characterizing the key factors affecting slide impact loading on pipelines.A comprehensive understanding of these results is essential for the sustainable development of deep-sea pipeline projects associated with seabed resource development and the implementation of disaster prevention measures.

MXene Sediment-Based Poly(vinyl alcohol)/Sodium Alginate Aerogel Evaporator with Vertically Aligned Channels for Highly Efficient Solar Steam Generation

Solar-driven interfacial evaporation from seawater is considered an effective way to alleviate the emerging freshwater crisis because of its green and environmentally friendly characteristics.However,developing an evaporator with high efficiency,stability,and salt resistance remains a key challenge.MXene,with an internal photothermal conversion efficiency of 100%,has received tremendous research interest as a photothermal material.However,the process to prepare the MXene with monolayer is inefficient and generates a large amount of“waste”MXene sediments(MS).Here,MXene sediments is selected as the photothermal material,and a three-dimensional MXene sediments/poly(vinyl alcohol)/sodium alginate aerogel evaporator with vertically aligned pores by directional freezing method is innovatively designed.The vertical porous structure enables the evaporator to improve water transport,light capture,and high evaporation rate.Cotton swabs and polypropylene are used as the water channel and support,respectively,thus fabricating a self-floating evaporator.The evaporator exhibits an evaporation rate of 3.6 kg m^(-2)h^(-1)under one-sun illumination,and 18.37 kg m^(-2)of freshwater is collected in the condensation collection device after 7 h of outdoor sun irradiation.The evaporator also displays excellent oil and salt resistance.This research fully utilizes“waste”MS,enabling a self-floating evaporation device for freshwater collection.

Multiparameter Numerical Investigation of Two Types of Moving Interactions Between the Deep-Sea Mining Vehicle Track Plate and Seabed Soil:Digging and Rotating Motions

To ensure the safe performance of deep-sea mining vehicles(DSMVs),it is necessary to study the mechanical characteristics of the interaction between the seabed soil and the track plate.The rotation and digging motions of the track plate are important links in the contact between the driving mechanism of the DSMV and seabed soil.In this study,a numerical simulation is conducted using the coupled Eulerian–Lagrangian(CEL)large deformation numerical method to investigate the interaction between the track plate of the DSMV and the seabed soil under two working conditions:rotating condition and digging condition.First,a soil numerical model is established based on the elastoplastic mechanical characterization using the basic physical and mechanical properties of the seabed soil obtained by in situ sampling.Subsequently,the soil disturbance mechanism and the dynamic mechanical response of the track plate under rotating and digging conditions are obtained through the analysis of the sensitivity of the motion parameters,the grouser structure,the layered soil features and the soil heterogeneity.The results indicate that the above parameters remarkably influence the interaction between the DSMV and the seabed soil.Therefore,it is important to consider the rotating and digging motion of the DSMV in practical engineering to develop a detailed optimization design of the track plate.

Microplastics in sediment of the Three Gorges Reservoir:abundance and characteristics under different environmental conditions

Freshwater microplastic pollution is an urgent issue of global concern,and research on the distribution in reservoirs is lacking.We investigated the microplastic pollution levels in wet sediments collected from the Three Gorges Reservoir,the largest reservoir of China.Results show that microplastics were ubiquitous in the sediments of the Three Gorges Reservoir,and their abundance ranged from 59 to 276 pp/kg(plastic particles per kg,dry weight).Economic development and total population were important factors affecting the spatial heterogeneity of microplastic abundance,and the contribution of large cities along the reservoir to microplastic pollution should be paid with more attention.Fibrous microplastics were the most abundant type of microplastic particles in reservoir sediments,whereas polystyrene,polypropylene,and polyamide were the main types of polymers.The apparent spatial heterogeneity in morphology and color of microplastics is attributed to different anthropogenic or landbased pollution sources.Moreover,the accumulation of microplastics near the inlet of tributaries reflects the role of potential contributors of tributaries.More importantly,multiple bisphenols(BPs)and heavy metals detected at the microplastic surfaces indicate that microplastics can act as carriers of these pollutants in the environment in the same way as sediments did,which may alter the environmental fate and toxicity of these pollutants.Therefore,we conclude that the Three Gorges Reservoir had been contaminated with microplastics,which posed a stress risk for organisms who ingest them along with their associated pollutants(BPs,heavy metals).

MEASUREMENTS OF ANNUAL DEPOSIT MASS OF COSMIC DUST BY DEEP-SEA SEDIMENTATION

We measured the annual deposit mass of cosmic dust on the Earth based on average sedimentation rate and content of cosmic dust at 20 surface stations on the Pacific investigation area (6°—13°N, 166°—178°W). The results indicate that measured results of each station are more identical and in accord with most measured results in the past, too.

Microplastic and Heavy Metals Distributions in Urban Rivers Sediments,China

This study investigated the distribution of microplastics and heavy metals,along with the interaction between the two in the sediments of urban rivers in China.Results showed that the abundance of microplastics ranged from 2412±187.5 to 7638±1312items kg^(-1)dry sediment across different survey stations,with an average abundance at(4388±713)items kg^(-1)dry sediment.Upon further categorization,it was found that transparent fragments were the primary color and type of microplastics present.The potential ecological risk index(RI)of heavy metals in sediments suggested a low level of ecological risk within a majority of the urban rivers studied.Cd was identified as the main potential ecological risk factor in the sediments of the studied areas.There was a relatively good significant linear relationship between the RI of heavy metals and the abundance of microplastics,bolstering the linkage between these two environmental pollutants.However,the concentrations of heavy metals in microplastics were not dependent on their corresponding contents in sediments.In fact,the concentration of Cu,Cd,and As in microplastics were higher than those in the sediments.This finding confirmed that microplastics could serve as carriers of heavy metals and introduce potential risks to aquatic wildlife and human through the food chain.