Poroelastodynamic responses and elastic moduli of a transversely isotropic porous cylinder under forced deformation test

Existing transversely isotropic poroelastodynamics solutions are limited to infinite domains and without experimental validation. Furthermore, there is a lack of analytical simulations for the elastic moduli dispersion of fluid-saturated porous cylinders. To address these three limitations and investigate the mechanisms of moduli dispersion, we present the analytical solutions of the poromechanical responses and the elastic moduli dispersion of a transversely isotropic, fluid-saturated, finite porous cylinder subjected to a forced deformation test. Through an example, we demonstrate the effects of loading frequency, boundary conditions, and material's anisotropy, dimension, and permeability on the responses of pore pressure,force, displacement, and dynamic elastic moduli of the cylinder. The specimen's responses are significantly influenced by the frequency of the applied load, resulting in a drained state at low frequencies and an undrained state at high frequencies. At high frequencies, the sample behaves identically for an open or a closed lateral boundary, and permeability has insignificant effects. The dynamic elastic moduli are mainly controlled by the loading frequency and the ratio of the sample's radius to its height. Lastly,we show excellent matches between the newly derived analytical solution and laboratory measurements on one clay and two shale samples from Mont Terri.

Quantitative analysis of deformation in hollow cylinder tests on anisotropic clay formations

A series of triaxial laboratory experiments are performed on thick-walled hollow cylindrical samples of boom clay.The aim of this testing program is to better understand the anisotropic deformation during the excavation.The testing conditions are similar to those to be experienced by host rocks around disposal galleries for radioactive waste.X-ray computed tomography is performed at different steps for each test with the samples remaining inside the loading cell.Initial analysis of the tomography images allows of the observation of the deformation of the central hole.In addition,particles manual tracking and 3D volumetric digital image correlation processing methods are considered being used to analyze the particles displacements and the boundary deformation of the sample quantitatively.An unsymmetrical damaged zone is induced around the hole,with a reverse deformation trend being found at the boundary after unloading,which indicates that the significant anisotropic deformation of boom clay can be induced by mechanical unloading.

RELIABILITY OF TEST LANDS TARGETING IN BED-OF-NAILS STYLE TEST FIXTURE

A systematic, accurate and robust evaluating method for fine pitch printed circuit board （PCB） positioning assessment in testing fixture is developed. Targeting reliability of bed-of-nails tester is successfully evaluated by the 2D pattern transform. Probe offset vector with its Weibull and Gaussian distribution estimates are obtained for further investigation about the causes of misalignment on the basis of a batch tests for same kind of PCBs.

Feasibility of columnar jointed basalt used for high-arch dam foundation

Columnar jointed basalt, with a lot of small-spacing structural planes and poor integrity, is a kind of fractured rock mass. Through comprehensive study of columnar joints shape, roughness of fracture surface and chemical composition of basalt, it is known that columnar joints of Baihetan dam area were formed as a result of cooling and shrinkage effects of magma. The columnar jointed basalt is mainly formed through chemical reaction of chlorite, kaolinite, epidote and tremolite, and the columnar joints mainly consist of chlorite according to slice identification and chemical analysis. Test results show that the columnar jointed basalt has high uniaxial compressive strength, low friction coefficient, and high cohesion, shear strength and deformation index. Meanwhile, the columnar jointed basalt is closely locked, and joint surfaces are well closed. The permeability of the rock is quite weak, and the P-wave velocity in the rock could get up to 5 000 m/s. All these show good rock properties. The columnar joints develop regularly, different from the general fractured rock masses. In summary, the columnar jointed basalt can be used directly as a foundation of dam.

Addressing the permanent deformation behavior of hot mix asphalt by triaxial cyclic compression testing with cyclic confining pressure

Rutting or permanent deformation is one of the major distress modes of hot mix asphalt in the field. Triaxial cycle compression testing （TCCT） is a standardized and scientifically accepted test method to address this distress mode in the lab and to characterize the resistance to permanent deformation. In most labs and according to EN 12697-25, standard TGCTs are carried out with cyclic axial loading and a constant confining pressure. In road pavements on the other hand, dynamic traffic loading due to passing wheels leads to cyclic confining pressure. In order to bring the TCCT closer to reality, the radial reaction and its phase lag to axial loading in standard TCCTs are analyzed and an enhanced TCCT with cyclic confining pressure is introduced. The cyclic confining pressure takes into account the viscoelastic material response by the radial phase lag to axial phase loading. In a subsequent test program, TCCTs with different confining pressure amplitudes were carried out on two hot mix asphalts. Results from standard and enhanced TCCTs were analyzed, compared and discussed. It is shown that the resistance to permanent deformation in- creases significantly when the viscoelastic material response is taken into account in the TCCT by introducing cyclic confining pressure.

Seismic earth pressures on flexible cantilever retaining walls with deformable inclusions

In this study, the results of 1-g shaking table tests performed on small-scale flexible cantilever wallmodels retaining composite backfill made of a deformable geofoam inclusion and granular cohesionlessmaterial were presented. Two different polystyrene materials were utilized as deformable inclusions.Lateral dynamic earth pressures and wall displacements at different elevations of the retaining wallmodel were monitored during the tests. The earth pressures and displacements of the retaining wallswith deformable inclusions were compared with those of the models without geofoam inclusions.Comparisons indicated that geofoam panels of low stiffness installed against the retaining wall modelaffect displacement and dynamic lateral pressure profile along the wall height. Depending on the inclusioncharacteristics and the wall flexibility, up to 50% reduction in dynamic earth pressures wasobserved. The efficiency of load and displacement reduction decreased as the flexibility ratio of the wallmodel increased. On the other hand, dynamic load reduction efficiency of the deformable inclusionincreased as the amplitude and frequency ratio of the seismic excitation increased. Relative flexibility ofthe deformable layer （the thickness and the elastic stiffness of the polystyrene material） played animportant role in the amount of load reduction. Dynamic earth pressure coefficients were compared withthose calculated with an analytical approach. Pressure coefficients calculated with this method werefound to be in good agreement with the results of the tests performed on the wall model having lowflexibility ratio. It was observed that deformable inclusions reduce residual wall stresses observed at theend of seismic excitation thus contributing to the post-earthquake stability of the retaining wall. Thegraphs presented within this paper regarding the dynamic earth pressure coefficients versus the wallflexibility and inclusion characteristics may serve for the seismic design of full-scale retaining walls withdeformable polystyrene inclusions. 2014 Institute of Rock and Soil Mechanics, Chinese Academy of Sciences. Production and hosting byElsevier B.V. All rights reserved.

Measurement of Thermal Expansion Coefficients with Holographic Technique

A simplified mathematical model was created for measurement of thermal expansion coefficients of thinsheet materials with holographic technique. Experimental set-ups corresponding to the mathematicalmodel were designed and built for both tests above room temperature and at low temperatures. Afringe control technique was introduced for low temperature measurements to compensate rigid bodymovement. Thin sheet specimens of silicon and aluminum alloy (7075) were tested with the developedtechnique. The tested results are in good agreement with reported data and thus verify the validityof the developed technique. The thermal expansion coefficients of the tested materials ranged from2.5×10-6C-1 to 23.6×0-60C-1.